Linear NAPFOB01 User Manual
PRODUCT DESCRIPTION
A1
A2
A1
A2
A1
A2
NAPFOB01
4-BUTTON
KEY FOB
TRANSMITTER
Operation
Instructions
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
A1
A2
The Model NAPFOB01 is a four button, battery powered, water-resistant,
transmitter designed for use with NAPCO
Pressing one of the buttons on the transmitter sends a digital coded
wireless signal to its companion receiver and lights the red signal indicator
on the transmitter. The transmitter sends variations of the code depending
on which button is pressed. The code format features over 4 billion
different encrypted code sequences. To ensure sending a signal, press
the transmitter button for a minimum of 2 seconds.
Each transmitter is powered by two self-contained type CR2025 3-volt
lithium batteries (included). Every activation, the transmitter sends its
battery status to the receiver. If the battery is low, a low battery signal is
sent to the receiver.
Receivers must be programmed to the transmitter’s code before system
testing and operation. Refer to the receiver’s instructions for details on
operation and programming.
The transmitter is supplied with an optional mounting bracket and a belt
clip. For stationary applications, the transmitter snaps into the mounting
bracket. For portable use, the belt clip attaches to mounting bracket
allowing the unit to be clipped to shirt pocket or slid onto a belt.
®
GEM and GEM-C systems.
PROGRAMMING BATTERY REPLACEMENT LINEAR LIMITED WARRANTY
2
For a detail programming guide, the instruction
manual should be consulted for that panel. The
below guide should only be used as a
reference and not as a replacement for using
the programming instructions.
1. Enter Keyfob Number (1-8)
2. Select Area Number (0 to disable, 1-2)
3. Enter 6 Digit ID Number (located on back
of unit).
4. Enter Check sum (0-9 ; A-F) (located on
back of unit) Digit that follows ¨:¨ on the
Serial ID. For A-F use 0 - 5 (See Below)
5. Enter AUX (OP)
0-None A-Keypad Aux
1-Relay Group 1 B-Instant
2-Relay Group 2 C-PGM 2 Output
9-Keypad Panic D-Access on
PGM2
6. Push On/Off to Save
Alpha Numeric Conversion
A = *0 D = *3
B = *1 E = *4
C = *2 F = *5
1
4
3
The NAPFOB01 Keyfob is defaulted with
buttons 1 and 2 being setfor instant
transmission and button 3 and 4 (A1 and
A2) with a 3 second hold down transmission
delay.
Only if you wish to change factory defaults
follow these steps:
Enter Programming - Press all 4 buttons on
the remote at the same time. Once LED
comes on let go - the LED will begin
flashing rapidly.
Press Button 1 ( ) - To switch between
instant or .5 second delay on buttons 1-2
(Instant is the default)
Press Button 2 ( ) - To switch between
Instant or 3 second delay on button 4
(Default is 3 second delay)
Press Button 4 - Turn Button 4 Active or Not
Active (Default is Active).
NOTE: You must re-enter keyfob programming each time a feature is to be changed
REPLACE BATTERIES
3
WITH TWO TYPE CR2025
LITHIUM BATTERIES
PLUS SIDE DOWN
REVERSE STEPS TO
4
REASSEMBLE TRANSMITTER
KEEP AWAY FROM SMALL CHILDREN. IF BATTERIES ARE SWALLOWED,
PROMPTLY SEE A DOCTOR. DO NOT TRY TO RECHARGE THESE BATTERIES.
DISPOSAL OF USED BATTERIES MUST BE MADE IN ACCORDANCE WITH THE
WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.
CR2025
TWIST COIN IN
1
SLOT TO OPEN
TRANSMITTER
CR2025
CAREFULLY REMOVE
2
RETAINING SCREW
AND LIFT OUT BOARD
NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM
BATTERY INFORMATION: THIS PRODUCT CONTAINS A CR
COIN CELL LITHIUM BATTERY WHICH CONTAINS
PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY SEE WWW.DTSC.CA.GOV/HAZARDOUSWASTE/PERCHLORATE
SIDE
DANGER OF EXPLOSION IF BATTERIES
SIDE
REPLACE ONLY WITH THE SAME OR
EQUIVALENT TYPE RECOMMENDED BY
BE CAREFUL NOT TO
DROP SCREW ON BOARD
WARNING
ARE INSTALLED INCORRECTLY.
THE MANUFACTURER.
FEATURES
MOUNTING
BELT
CLIP
KEY FOB
TRANSMITTER
This Linear product is warranted against defects in material and workmanship for twelve (12) months. This
warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal
distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from
their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities
on the part of Linear LLC for consequential damages arising out of or in connection with use or
performance of this product or other indirect damages with respect to loss of property, revenue,
or profi t, or cost of removal, installation, or reinstallation. All implied warranties, including implied
warranties for merchantability and implied warranties for fi tness, are valid only until the warranty expires.
This Linear LLC Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact
Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
Linear radio controls provide a reliable communications link and fi ll an important need in portable wireless
signaling. However, there are some limitations which must be observed.
✴ For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as
Part 15 devices. As such, they have limited transmitter power and therefore limited range.
✴ A receiver cannot respond to more than one transmitted signal at a time and may be blocked by
radio signals that occur on or near their operating frequencies, regardless of code settings.
✴ Changes or modifi cations to the device may void FCC compliance.
✴ Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
✴ A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale
distributor or dealer, and these facts should be communicated to the ultimate users.
This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Copyright © 2013 Linear LLC 187-1772 B
BRACKET
A1
IMPORTANT !!!
A2
ACTIVATION
BUTTONS
Loading...