Linear GD00Z-4 User Manual

GD00Z-4

GARAGE DOOR OPENER REMOTE COMMAND TRANSCEIVER with TILT SENSOR

Installation Instructions

USA & Canada (800) 421-1587 & (800) 392-0123

(760) 438-7000 - Toll Free FAX (800) 468-1340

www.linearcorp.com

PRODUCT DESCRIPTION

➊

GD00Z-4 Overview

• A garage door opener remote command transceiver with built-in Z-Wave technology.

• Allows remote operation of a garage door opener using Z-Wave controllers.

• Acts as a Z-Wave repeater to improve communications within the Z-Wave mesh network.

GD00Z-4 Summary of Operation

• GD00Z-4 connects to the garage door opener’s pushbutton wall console terminals.

• A wireless tilt sensor mounts on the garage door and reports the door’s position to the GD00Z-4.

• GD00Z-4 responds to Z-Wave commands from Z-Wave controllers to open or close the garage door.

• A warning indicator light ﬂ ashes and a beeper sounds for 5 seconds before the door begins to move.

• If the door does not completely open or close, a second open or close command can be sent after 30 seconds.

• If the door does not completely open or close after the second attempt, the GD00Z-4 operation is suspended until a local garage door pushbutton is activated.

Z-Wave Information

• Z-Wave® is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.

• Z-Wave is an Interoperable two-way RF mesh networking technology designed for use with a Z-Wave gateway/ controller and other Z-Wave enabled devices.

• Replication is the process of copying or transferring your Z-Wave network from one controller to another.

• This is a Security enabled Z-Wave product and must be used with a Security enabled Z-Wave controller in order to fully utilize this product. As such, this device will not respond to Basic CC commands.

• ASSOCIATION: The GD00Z-4 s 1 Group with 1 Node. Group 1 must be assigned the Node ID of the controller to which unsolicited notiﬁ cations from the GD00Z-4 will be sent. The Z-Wave controller should set this association automatically after inclusion.

upports

SAFETY NOTES

➋

WARNING

This operator system is equipped with an unattended operation feature. This door could move unexpectedly. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!

WARNING

This system can be installed on sectional type (roll up) doors only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!

WARNING

The Remote Command Transceiver must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard.

WARNING

Do not install the Remote Command Transceiver on garage door operators manufactured prior to 1993 (models without an operational safety beam entrapment detection system).

PRODUCT COMPONENTS

➌

POWER

INPUT

JACK

CONNECTION

WIRES

OPTIONAL

ADJUSTABLE

GD00Z-4 MOUNTING

BRACKET

TILT

SENSOR

INDICATOR

MOUNTING HARDWARE

SCREWS AND

MOUNTING TAPE

FOR TILT SENSOR

STATUS

SCREW AND

FOR ADJUSTABLE

BRACKET

GD00Z-4

POWER

SUPPLY

WIRE

TIES

WARNING

LIGHT

LINK

BUTTON

MOUNTING SCREWS

AND ANCHORS

FOR GD00Z-4

POWER

SUPPLY

RETAINING

BRACKET

SCREW FOR

POWER SUPPLY

BRACKET

TILT SENSOR INSTALLATION AND BATTERY

➍

To activate the tilt sensor,

remove the battery protection pull strip

Attach the mounting plate to the top panel of the door

Use double sided tape or

the two mounting screws supplied

(drill 1/16" pilot holes if required)

The system will notify you when the battery is low, replace the battery with a type CR2032 coin cell

To open the case, twist

a small screwdriver in case slot

LOW BATTERY REPLACEMENT

SLOT

Snap the sensor onto the mounting plate

ARROWS ON PLATE

& SENSOR POINT UP

"UP"

ARROWS

POST ON BOTTOM

Insert the

battery into the transmitter

PLUS SIDE UP !!!

CR2032

PAIRING (INCLUDING) WITH THE SYSTEM

➎

Note: Plug in the GD00Z-4 near your Z-Wave Controller for these steps

WALL

OUTLET

POWER SUPPLY

TO INCLUDE THE GD00Z-4 INTO YOUR CONTROLLER

Place your Z-Wave Controller into

Discovery or Include mode.

Press and release the link button

on the GD00Z-4.

Confirm that the GD00Z-4 was

recognized by your Z-Wave Controller.

Refer to your Z-Wave Controllers instructions for additional information on including devices.

POWER

INPUT

JACK

GD00Z-4

Refer to your Z-Wave Controllers instructions for additional information on excluding devices.

LINK

BUTTON

TO EXCLUDE THE GD00Z-4 FROM YOUR CONTROLLER

Place your Z-Wave Controller into Exclude mode.

Press and release the link button on the GD00Z-4.

Confirm that the GD00Z-4 was excluded by your Z-Wave Controller.

GD00Z-4 MOUNTING

➏

Tilt sensor mounted on the top panel of the door

Use the four screws

and anchors to mount the GD00Z-4 above the opener

3/16" HOLES

FOR ANCHORS

The GD00Z-4 typically mounts on the ceiling near the opener and the power outlet

! WARNING !

REMOVE POWER FROM THE

GARAGE DOOR OPENER

BEFORE CONTINUING

THE GD00Z-4 CAN ALSO BE ATTACHED TO THE OPENER'S

HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET

Secure bracket with screw

INDENT

THE GD00Z-4 WARNING

LAMP MUST BE VISIBLE IN

ALL DOOR POSITIONS

The optional adjustable

mounting bracket fits 3 ways on the GD00Z-4

The bracket snaps onto indents on either side or on the end of the GD00Z-4

INDENT

Use the bolts and nuts supplied to attach the bracket to a secure structure

BE SURE THE GD00Z-4 IS CLEAR OF ALL MOVING PARTS OF THE GARAGE DOOR AND THE WARNING LAMP IS NOT OBSTRUCTED

GD00Z-4 CONNECTIONS

➐

Connect the GD00Z-4 connection wires to the pushbutton wall console terminals on the garage door opener. The terminals may be named "PWC", "WC", "PB", "PUSHBUTTON", or "RED and WHITE". Terminal names and locations vary by model.

Either wire can connect to either terminal

GARAGE

DOOR

OPENER

Plug the power cord into the power input jack on the GD00Z-4

PUSHBUTTON

Remove the screw from 120 VAC

outlet faceplate. Secure the retaining bracket to the faceplate with the provided screw. Snap the power supply into the bracket while plugging into the outlet.

DO NOT DISCONNECT

ANY WIRES CURRENTLY

CONNECTED TO THE

GARAGE DOOR OPENER !!!

USE WIRE TIES TO SECURE EXCESS WIRING CLEAR OF ALL MOVING PARTS OF THE GARAGE DOOR AND OPENER

SYSTEM OPERATION

➑

Restore power to your

garage door opener

To synchronize the system,

use the garage door opener's pushbutton to manually open and close the door

Use your Z-Wave Controller to activate your garage door opener

The GD00Z-4 will beep and

flash for five seconds before the door moves

The GD00Z-4 will activate

the door opener and open or close the door

FLASH

BEEP

FLASH

BEEP

FLASH

STAY CLEAR

OF THE DOOR !!!

STAY CLEAR

OF THE DOOR !!!

OPERATION NOTES

➒

1. The warning light will ﬂ ash and the warning beeper will sound for ﬁ ve seconds before the door opener is activated. STAY CLEAR OF THE DOOR, AND DOOR

OPENER. THEY ARE ABOUT TO MOVE!

2. If the door does not completely open or close after remote activation, the GD00Z-4

will allow user to try to operate the door one more time. If the second attempt fails, the GD00Z-4 will go into lock-out mode. See Note #3.

3. If the GD00Z-4 is in lock-out mode and will not accept remote commands, activate the door from the pushbutton wall console.

4. Once the GD00Z-4 has initiated the movement of the garage door, another command cannot be sent for 30 seconds. This eliminates the chance of “bouncing” the garage door and possibly damaging the garage door opener.

GD00Z-4 Speciﬁ cations

Power Supply: Input: 120 VAC, 0.8 A Output: 12 VDC, 2 A

Operating Temperature: -4º—122° F (-20º—50° C)

Audible Alarm: 45 db @ 10 feet

Strobe: 360 Lumens

Communications: Z-Wave (908.4 MHz)

Mounting: Screws and anchors to

the ceiling, or bracket to the opener’s hanging hardware

Tilt Sensor Speciﬁ cations

Power Supply: Type CR2032 Coin Cell Battery

Operating Temperature: -4º—122° F (-20º—50° C)

Battery Life: 24 Months (typical)

Communications: Proprietary 345 MHz

Range: 100” line-of-sight to GD00Z-4

Mounting to Garage Door: Double-sided tape or two

mounting screws

(Speciﬁ cations subject to change without notice)

NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION: THIS

PRODUCT CONTAINS A CR COIN CELL LITHIUM

BATTERY WHICH CONTAINS PERCHLORATE

MATERIAL - SPECIAL HANDLING MAY APPLY - SEE

www.dtsc.ca.gov/hazardouswaste/perchlorate

KEEP AWAY FROM SMALL CHILDREN. IF BATTERY

IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO

NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL

OF USED BATTERIES MUST BE MADE IN

ACCORDANCE WITH THE WASTE RECOVERY AND

RECYCLING REGULATIONS IN YOUR AREA.

TROUBLESHOOTING

➓

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

Unable to include in Z-Wave network.

The GD00Z-4 does not ﬂ ash or beep when activated.

GD00Z-4 was not properly excluded from a previous Z-Wave network.

No power to the GD00Z-4.

1. Reset the GD00Z-4 by pressing the LINK button 5 times. A quick

beep followed by a longer beep will indicate the reset.

1. Make sure the power supply is plugged in securely to a live outlet.

2. Make sure the power cord is plugged in securely to the GD00Z-4.

The GD00Z-4 ﬂ ashes and beeps when activated but the door does not move.

Obstruction blocking the door or incorrect wiring.

1. Make sure that there are no obstacles preventing the door from moving.

2. Make sure that the GD00Z-4 connection wires are connected to the proper terminals on the garage door opener. Trace the wires from the garage door opener’s pushbutton wall console to the door opener. This is where the GD00Z-4 connection wires should be connected.

Garage door opens or closes, but the status does not change on the Z-Wave Controller.

The tilt sensor signal is not being received by the GD00Z-4.

1. Make sure the tilt sensor is mounted correctly on the garage door, with the arrow pointing up.

2. Make sure the battery pull tab has been removed from the tilt sensor.

3. Replace the battery in the tilt sensor.

LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12) months. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any.

There are no obligations or liabilities on the part of Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or proﬁ t, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for ﬁ tness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu of all other warranties express or implied.

All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Returns at 1-855-546-3351 for an RPA# and other impor tant details.

REGULATORY NOTICES

This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Changes or modiﬁ cations not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Les changements ou modiﬁ cations non approuvés expressément par la partie responsable de la conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.