Linear GD00Z-1 Installation Instructions Manual

Page 1
GD00Z-1
GARAGE DOOR OPENER REMOTE COMMAND CONTROLLER with TILT SENSOR
Installation Instructions
1. PRODUCT DESCRIPTION
The GD00Z-1 Controller connects to the garage door opener’s pushbutton wall console terminals and communicates with the Iris hub using Z-Wave radio signals. A wireless tilt sensor mounts on the garage door and reports the door’s position to the Controller. When the Controller receives a command from the Iris hub, it will open or close the garage door.
Anytime the garage door opener is activated remotely by the Controller, a warning indicator fl ashes and a beeper sounds for fi ve seconds before the door begins to move.
If, due to an obstruction or other cause, the door does not completely open or close when it is activated remotely, the Controller will pause for 30 seconds. After the delay, a second remote activation can be attempted. If the door does not complete its motion on the second attempt, the Controller will suspend operation until the door is operated locally with the opener’s pushbutton wall console.
The Controller is powered by a plug-in power supply. The Model TILT 345 tilt sensor is powered by a 2032 lithium battery. If the tilt sensor battery is low, it will be reported to the Iris hub by the Controller. A link button and status light are provided on the Controller for adding or removing the device with the Iris hub.
Four screws and anchors are provided for mounting the Controller. An adjustable controller mounting bracket with hardware is supplied for installing the unit onto the door opener’s hanging hardware. The wireless tilt sensor mounts with double sided tape or the two screws supplied.
2. SAFETY NOTES
3. PRODUCT FE ATURES 4. TILT SENSOR INSTALLATION AND BATTERY 5. PAIRING WITH IRIS
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-1 - LINEAR P/N: 235686 X22 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
WARNING
This operator system is equipped with an unattended operation feature. This door could move unexpectedly. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
Do not install the Remote Command Controller on garage door operators manufactured prior to 1993 (models without an operational safety beam entrapment detection system).
WARNING
The Remote Command Controller must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard.
Z-Wave® is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.
CONTROLLER
POWER
INPUT
JACK
WARNING
LIGHT
LINK
BUTTON
CONTROLLER CONNECTION
WIRES
DOUBLE SIDED
MOUNTING TAPE,
SCREWS AND ANCHORS
POWER SUPPLY
TILT
SENSOR
STATUS
INDICATOR
ADJUSTABLE
MOUNTING
BRACKET
(OPTIONAL)
POWER SUPPLY
RETAINING
BRACKET
PARING THE CONTROLLER
REMOVING THE CONTROLLER
TO PAIR WITH THE IRIS HUB
TO REMOVE FROM
THE IRIS HUB
FROM THE IRIS WEB SITE, CLICK "DEVICES", THEN CLICK THE "ADD DEVICES" BUTTON
FOLLOW THE ON-SCREEN INSTRUCTIONS TO PAIR THE CONTROLLER WITH THE HUB
SELECT GARAGE DOOR CONTROLLER FROM THE LIST
1
2
3
1
2
4
FROM THE IRIS WEB SITE, CLICK "DEVICES"
ON THE GARAGE DOOR CONTROLLER DEVICE CLICK "MANAGE", THEN CLICK "REMOVE"
FOLLOW THE ON-SCREEN INSTRUCTIONS TO UN-PAIR THE CONTROLLER WITH THE HUB
3
WALL
OUTLET
POWER SUPPLY
POWER
INPUT
JACK
LINK
BUTTON
CONTROLLER
WHEN INSTRUCTED, PRESS THE LINK BUTTON ON THE CONTROLLER
4
WHEN INSTRUCTED, PRESS THE LINK BUTTON ON THE CONTROLLER
www.lowes.com/iris
CR2032
PLUS SIDE UP !!!
IRIS WILL NOTIFY YOU WHEN THE BATTERY IS LOW, REPLACE THE BATTERY WITH A TYPE CR2032 COIN CELL
INSERT THE BATTERY INTO THE TRANSMITTER
TO OPEN THE CASE, TWIST A SMALL SCREWDRIVER IN CASE SLOT
SLOT
ATTACH MOUNTING PLATE TO
TOP PANEL
OF THE DOOR
USE DOUBLE SIDED TAPE OR
THE TWO MOUNTING SCREWS SUPPLIED
(DRILL 1/16" PILOT HOLES IF REQUIRED)
POST ON BOTTOM
"UP"
ARROWS
SNAP SENSOR ONTO THE MOUNTING PLATE
TO ACTIVATE THE TILT SENSOR, REMOVE THE BATTERY PROTECTION PULL STRIP
ARROWS ON PLATE & SENSOR POINT UP
Page 2
6. CONTROLLER MOUNTING 7. CONTROLLER CONNECTIONS 8. SYSTEM OPERATION
9. OPERATION NOTES
1. The warning light will fl ash and the warning beeper will sound fi ve seconds before the door opener is activated. STAY CLEAR
OF THE DOOR, AND DOOR OPENER. THEY ARE ABOUT TO MOVE!
2. If the door does not completely open or close after remote
activation, the Controller will allow user to try to operate the door one more time. If the second attempt fails, the Controller will go into lock-out mode and blink the status indicator. See Note #3.
3. If the status indicator is blinking, the Controller is in lock-out mode and will not accept remote commands. Activate the door from the pushbutton wall console then check that the status indicator stops blinking.
10. TROUBLESHOOTING
PROBLEM
POSSIBLE
CAUSE
CORRECTIVE ACTION
The Controller does not fl ash or beep when activated.
No power to the Controller.
1. Make sure the power supply is plugged in securely to a live outlet.
2. Make sure the power cord is plugged in securely to the Controller.
The Controller fl ashes and beeps when activated but the door does not move.
Obstruction blocking the door or incorrect wiring.
1. Make sure that there are no obstacles preventing the door from moving.
2. Make sure that the Controller’s connection wires are connected to the proper terminals on the garage door opener. Trace the wires from the garage door opener’s pushbutton wall console to the door opener. This is where the Controller’s connection wires should be connected to.
Garage door opens or closes, but the status does not change on the Iris website or mobile app.
The tilt sensor signal is not being received by the Controller.
1. Make sure the tilt sensor is mounted correctly on the garage door, with the arrow pointing up.
2. Make sure the battery pull tab has been removed from the tilt sensor.
3. Replace the battery in the tilt sensor.
LINEAR LIMITED RETAIL WARRANTY
Linear LLC (the Company) warrants to the original purchaser that products delivered hereunder will be free of defects in materials and workmanship for a period of one (1) year from the date of purchase.
The Company within said period shall at its option, either repair or replace free of charge, any product or part thereof found, upon the Company’s inspection, to be so defective, and will return the repaired or replaced product to the purchaser at Company’s expense.
All products returned for warranty service require a Return Product Authorization Number (RPA#). For warranty service, shipping instructions, and an RPA#, contact Linear Technical Services at 1-855-546-3351. Devices must be sent to the Company at owner’s expense and be accompanied with statement of defect and proof of purchase.
This warranty is conditioned on the following:
1. The Company must be notifi ed within one year of purchase and have been given the opportunity of inspection by return of any alleged defective product free and clear of all liens and encumbrances to the Company or its distributor; and
2. The product must not have been abused, misused or improperly maintained and/or repaired during such period; and
3. Such defect has not been caused by corrosion or exposure to other than ordinary wear and tear.
THE COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
The Company’s maximum liability hereunder is limited to the purchased price of the product. In no event shall the Company be liable for any consequential, indirect, incidental or special damages of any nature arising from the sale or use of the product, whether based in contract, tort, strict liability or otherwise.
Note: Some states do not allow limitations on incidental or consequential damages or how long an implied warranty lasts, so that the above limitations may not fully apply. This warranty gives specifi c legal rights and you may also have other rights which may vary from state to state.
This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-1 - LINEAR P/N: 235686 X22 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2
THE CONTROLLER TYPICALLY MOUNTS ON THE CEILING NEAR THE OPENER AND THE POWER OUTLET
TILT SENSOR MOUNTED ON THE TOP PANEL OF THE DOOR
THE CONTROLLER CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
THE CONTROLER'S WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
3/16" HOLES
FOR ANCHORS
THE OPTIONAL ADJUSTABLE MOUNTING BRACKET FITS 3 WAYS ON THE CONTROLLER
THE BRACKET SNAPS ONTO INDENTS ON EITHER SIDE OR ON THE END OF THE CONTROLLER
SECURE BRACKET WITH SCREW
USE THE FOUR SCREWS AND ANCHORS TO MOUNT THE CONTROLLER ABOVE THE OPENER
INDENT
INDENT
USE THE BOLTS AND NUTS SUPPLIED TO ATTACH THE BRACKET TO A SECURE STRUCTURE
BE SURE THE CONTROLLER IS CLEAR OF ALL MOVING PARTS OF THE GARAGE DOOR
INDENT
PUSHBUTTON
PUSHBUTTON
GARAGE
DOOR
OPENER
CONNECT THE CONTROLLER CONNECTION WIRES TO THE PUSHBUTTON WALL
CONSOLE TERMINALS ON THE GARAGE DOOR OPENER. THE TERMINALS MAY BE NAMED "PWC", "WC", "PB", "PUSHBUTTON", OR "RED AND WHITE". TERMINAL NAMES AND LOCATIONS VARY BY MODEL.
DO NOT DISCONNECT
ANY WIRES CURRENTLY
CONNECTED TO THE
GARAGE DOOR OPENER !!!
1
PLUG THE POWER SUPPLY INTO 115 VAC OUTLET AND SECURE IT WITH THE RETAINING BRACKET
BE SURE WIRES ARE CLEAR OF ALL MOVING PARTS OF THE GARAGE DOOR AND OPENER
3
EITHER WIRE CAN CONNECT TO EITHER TERMINAL
PLUG THE POWER CORD INTO THE POWER INPUT JACK ON THE CONTROLLER
2
FLASH
FLASH
FLASH
BEEP
BEEP
BEEP
USE THE IRIS WEB SITE AND MOBILE APPS TO CONTROL YOUR GARAGE DOOR, VIEW STATUS, AND SET CUSTOM RULES
THE CONTROLLER WILL ACTIVATE THE DOOR OPENER AND OPEN OR CLOSE THE DOOR
STAY CLEAR
OF THE DOOR !!!
1
THE CONTROLLER WILL BEEP AND FLASH FOR FIVE SECONDS BEFORE THE DOOR MOVES
2
3
4
THE IRIS WEB PAGE OR MOBILE APP WILL SHOW THE NEW STATUS OF THE DOOR AFTER THE DOOR COMPLETES ITS CYCLE
NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION:
THIS PRODUCT CONTAINS A CR COIN CELL LITHIUM BATTERY WHICH CONTAINS
PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY - SEE
www.dtsc.ca.gov/hazardouswaste/perchlorate
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.
Changes or modifi cations not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
Les changements ou modifi cations non approuvés expressément par la partie responsable de la conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
Copyright © 2014 Linear LLC 235686 X22
Loading...