Lift-master Q411 User Manual

Page 1
Part # Q411
CSW / SL Surge Protection Module for Non-OmniControl Commercial Gate Operators
Please read this entire manual before installation
Chamberlain Professional Products strongly recommends the installation of this Surge Protection Module to protect the gate operator from harmful surges caused by lightning strike phenomenon.
It is important to recognize that the surge protection module may not prevent damage to the gate operator in the event of a direct lightning strike.
The success of the surge protection will be based in the proper installation of the Surge Protection Module and the proper grounding of both the surge protector module and the gate operator itself.
This Surge Protection Module will provide protection for the following input commands.
Name of Lines Protected
External Safety Loop “Command” input External Exit Loop “Command” input Fire Department or Key switch “Open” command Strike Open or Push Button to open command Radio receiver “Command” input Ground reference and +24 VDC supply
DO NOT
CSW / SL SURGE SUPPRESSOR
P/N Q411 – P
P/N Q411 – P
USE WITH:
• OMNICONTROL BOARD OR
• OMNICONTROL BOARD OR
• ROBO CONTROL BOARD
• ROBO CONTROL BOARD
®
EXIT
EXIT
SAFTEY
ATENT PENDING
ATENT PENDING
SAFTEY
LOOP
LOOP
LOOP
LOOP
K
K
IR
IR
F
F
Y
Y
E
E
Number of Lines Protected
1 1 1 1 1 2
++
––
STRIKE OPEN
STRIKE OPEN
T
T
P
P
E
E
D
D
E
E
PUSH BUTTON
PUSH BUTTON
H
H
C
C
IT
IT
W
W
S
S
RADIO
RADIO
RECEIVER
RECEIVER
2
2
S
S
S
S
A
A
L
L
C
C
LY
LY
P
P
P
P
U
U
S
S
Earth Ground Rod Installation
Proper grounding gives an electrical charge, such as from an electrical static discharge or a near lightning strike, a path from which to dissipate its energy safely into the earth.
Without this path, the intense energy generated by lightning could be directed towards the gate operator. Although nothing can absorb the tremendous power of a direct lightning strike, proper grounding can protect the gate operator in most cases.
Before digging more than 18" deep, contact local underground utility locating companies.
Avoid damaging gas, power, or other underground utility lines.
The earth ground rod must be located within 3 feet from the gate operator. Use the proper type earth ground rod for your area.
The ground wire must be a single, whole piece of wire. Never splice two wires for the ground wire. If you should cut the ground wire too short, break it, or destroy its integrity, replace it with a single wire length.
Chamberlain Professional Products, Inc. is not responsible for improper installation or failure to comply with all necessary local building codes.
12 gauge wire
8 ft
®
Page 2
765432189
+
10
Exit LoopSafety Loop
Or Photocell
Strike Open or
Push Button
Fire Dep
Key Switch
Radio Receiver
-
765432189
+
10
Exit LoopSafety Loop
Or Photocell
Strike Open or
Push Button
Fire Dep
Key Switch
Radio Receiver
-
765432189
+
10
Exit LoopSafety Loop
Or Photocell
Strike Open or
Push Button
Fire Dep
Key Switch
Radio Receiver
-
765432189
+
10
Exit LoopSafety Loop
Or Photocell
Strike Open or
Push Button
Fire Dep
Key Switch
Radio Receiver
-
765432189
+
10
Exit LoopSafety Loop
Or Photocell
Strike Open or
Push Button
Fire Dep
Key Switch
Radio Receiver
-
CSW / SL Surge Protection Module
Step-by-Step instructions
STEP 2
Remove J1 plug.
STEP 1
STEP 5
Use a nut driver and remove the 2 hex nuts holding the terminal block connector (10 terminals) on the electrical box.
STEP 6
Remove the terminal block connector from the electrical box.
STEP 3
Remove the wire nuts from the black and white wires (16 AGW) coming from the plug .
STEP 4
Remove all the accessory wires attached to the terminal block. Make sure to mark all the wires you are removing to reconnect them later.
OffOff
OffOff
OnOn
OnOn
OnOn
OffOff
OffOff
OffOff
OnOn
OffOff
OffOff
Gate Operator
M
ain
Room
Eug. Rm Oper. Rm
Eug. Dept. M
anu. 1 Rm
Main Dept. Manu. 2 Rm
Air (1)
Conditioner
Air (2)
Conditioner
C
onfere
nce
R
oom
1
Conference
Rm
2, 3
Refer.
Bus 1, 2, 3
Conference
Room 2
C
o
m
p
.
S
erve
2
C
o
m
p.
S
e
rve
1
Turn the gate operator off by turning off the building/facility breaker for the 120 Vac supply to the gate operator.
®
C
S
W
/ S
L
S
U
R
G
E
Page 3
765432189
+
10
Exit LoopSafety Loop
Or Photocell
Strike Open or
Push Button
Fire Dep
Key Switch
Radio Receiver
-
STEP 9
STEP 11
Use supplied wire nuts to connect the AC wire coming from the outlet (through the channel in the electrical box) to the plug (black to black and white to white wires 16 AGW).
STEP 12
STEP 10
Connect the plug of the Surge Protector to the J1 connector on the control board.
STEP 7
Place the Surge Protector module in place of the terminal block. Use a nut driver to secure the 2, 1 inch long hex nuts that came with the module.
STEP 8
Remove the control board and unscrew the lower left hex nut under the board. Slip the ring terminal on the screw stud. Make sure ring is in contact with the control box. Re-screw the hex nut and re-attach the control board.
P/N
Q
41
1
– P
A
T
E
N
T PEN
D
IN
G
P/N
Q
41
1
– P
A
T
E
N
T PEN
D
IN
G
®
S
T
R
IK
E
O
P
E
N
P
U
S
H
B
U
T
T
O
N
S
T
R
IK
E
O
P
E
N
P
U
S
H
B
U
T
T
O
N
FIRE D
EPT
K
EY
SW
ITCH
FIRE D
EPT
K
EY
SW
ITCH
C
L
A
S
S
2
S
U
P
P
L
Y
C
L
A
S
S
2
S
U
P
P
L
Y
SAFTEY
LOOP
SAFTEY
LOOP
RADIO
RECEIVER
RADIO
RECEIVER
EXIT LOOP
EXIT LOOP
––
++
C
S
W
/ S
L
S
U
R
G
E
S
U
P
P
R
E
S
S
O
R
P/
N
Q
4
11
– P
A
TEN
T PEN
D
IN
G
P/
N
Q
4
11
– P
A
TEN
T PEN
D
IN
G
®
S
T
R
I
K
E
O
P
E
N
P
U
S
H
B
U
T
T
O
N
S
T
R
I
K
E
O
P
E
N
P
U
S
H
B
U
T
T
O
N
FIR
E D
E
PT
K
E
Y
SW
ITCH
FIR
E D
E
PT
K
E
Y
SW
ITCH
C
L
A
S
S
2
S
U
P
P
L
Y
C
L
A
S
S
2
S
U
P
P
L
Y
SAFTEY
LOOP
SAFTEY
LOOP
RADIO
RECEIVER
RADIO
RECEIVER
EXIT
LOOP
EXIT LOOP
––
++
C
S
W
/ S
L
S
U
R
G
E
S
U
P
P
R
E
S
S
O
R
P/
N
Q
4
1
1
– P
A
TE
N
T PE
N
DIN
G
P/
N
Q
4
1
1
– P
A
TE
N
T PE
N
DIN
G
®
S
T
R
I
K
E
O
P
E
N
P
U
S
H
B
U
T
T
O
N
S
T
R
I
K
E
O
P
E
N
P
U
S
H
B
U
T
T
O
N
FIR
E
D
EPT
K
EY SWITCH
FIR
E
D
EPT
K
EY SWITCH
C
L
A
S
S
2
S
U
P
P
L
Y
C
L
A
S
S
2
S
U
P
P
L
Y
SAFTEY
LOOP
SAFTEY
LOOP
RADIO
RECEIVER
RADIO
RECEIVER
EXIT LOOP
EXIT LOOP
––
++
C
S
W
/
S
L
S
U
R
G
E
S
U
P
P
R
E
S
S
O
R
P
/
N
Q
4
1
1
P
A
T
E
N
T
P
E
N
D
IN
G
P
/
N
Q
4
1
1
P
A
T
E
N
T
P
E
N
D
IN
G
®
SAFTEY
LOOP
SAFTEY
LOOP
EXIT
LOOP
EXIT
LOOP
CSW / SL SURGE SUPPRESSOR
There is a green wire with a ring terminal coming out of the Surge Protection module, This ring terminal MUST make good
contact with the chassis of the gate operator.
Reconnect the accessory wires to the Surge Protector. Match them up with the label on the module. All the connectors on the module are removable for easy wiring.
P/N
Q
4
11
– P
A
TEN
T PEN
D
IN
G
P/N
Q
4
11
– P
A
TEN
T PEN
D
IN
G
®
S
T
R
IK
E
O
P
E
N
P
U
S
H
B
U
T
T
O
N
S
T
R
IK
E
O
P
E
N
P
U
S
H
B
U
T
T
O
N
FIR
E D
EPT
K
EY
SW
ITCH
FIR
E D
EPT
K
EY
SW
ITCH
C
L
A
S
S
2
S
U
P
P
L
Y
C
L
A
S
S
2
S
U
P
P
L
Y
SAFTEY
LOOP
SAFTEY
LOOP
RADIO
RECEIVER
RADIO
RECEIVER
EXIT LOOP
EXIT LOOP
––
++
C
S
W
/ S
L
S
U
R
G
E
S
U
P
P
R
E
S
S
O
R
®
C
S
W
/ S
L
S
U
R
G
E
OffOff
OffOff
OnOn
OnOn
OnOn
OffOff
OffOff
OffOff
OnOn
OffOff
OffOff
Gate
Operator
M
ain
Room
Eug. Rm
Oper. Rm
Eug. Dept.
M
anu. 1 Rm
Main Dept.
Manu. 2 Rm
Air (1) Conditioner
Air (2)
Conditioner
C
onf
e
re
nce
Ro
om
1
Conferen
ce
R
m
2
, 3
Refer.
Bus 1, 2, 3
Conference
Room
2
C
om
p.
S
e
rv
e
2
C
o
m
p
.
S
e
r
ve
1
Turn the gate operator back on by turning on the building/facility breaker for the 120 Vac supply to the gate operator.
®
Page 4
CSW / SL Surge Protection Module
STEP 13
Test all the accessories in combination with the gate operator to corroborate proper installation and functionality.
Step-by-Step instructions (con't)
01-50739
For additional protection against surges, ensure that the cables or wires going to your accessories comply with the following rules:
All wires going the accessories must be shielded wires. The shield must be connected as follows: A) At the gate operator: To the chassis of the gate operator B) At the accessories: To their chassis (Earth grounding at the accessories will be even more beneficial)
Ensure that the connections to the chassis are made secure to create good contact.
© 2005 The Chamberlain Group, Inc.
All Rights Reserved
For Technical Support: 1-800-528-2806
845 Larch Avenue Elmhurst, Illinois 60126
www.chamberlain.com
®
Loading...