LiftMaster CSL24V User Manual

QuickStart for single gate applications

This QuickStart is intended to highlight a single right-hand gate application. Each application is unique and it is the responsibility of the purchaser, installer and end user to ensure that the total gate system is installed and operated properly. Refer to the installation manual for complete information regarding installation, testing, and programming.

INSTALLATION

1 Install the concrete pad and conduit.

™

MODEL CSL24V™& CSL24VH

INSTALL THE COVER

2 Attach the operator to the concrete pad. 3 Attach the gate brackets to the gate. 4 Close the gate. 5 Route the chain through the operator. 6 Connect the chain to the gate brackets. 7 Remove the pin from the vent plug on the gear box.

Close the gate BEFORE installing the chain.

Align the tabs on the rear cover with the slots on the chassis

and place the cover over the operator.

2 Secure both sides of the rear cover to the chassis with two

5/16-18 hex bolts and washers.

3 Align the front cover with the back cover, making sure the

grooves line up.

4 Secure the front cover to the chassis with two 5/16-18 hex

bolts and washers.

5 Secure the front cover to the rear cover using the 5/16-18

screw.

5/16-18 Screw

Tabs on Rear Cover

5/16-18 Hex Bolts and Washers

Slots on Chassis

Groove on Front Cover

+ DC

+ BATT

WIRING

SET OPEN

SET CLOSE

OFF

PRESS & RELEASE TO BEGIN

MOVE GATE

INPUT POWER

PRESS & RELEASE TO BEGIN

SETUP

LIMIT

TO BEGIN

PRESS & RELEASE TO BEGIN

180

MIN

MAX

BATT LOW

NETWORK

OPEN

STOP

XMITTER

NETWORK

To protect against fire and electrocution:

• DISCONNECT power and battery BEFORE installing or servicing operator.

For continued protection against fire:

• Replace ONLY with fuse of same type and rating.

INITIAL LIMITS AND FORCE ADJUSTMENT

1 Press and release the SET OPEN and SET CLOSE buttons simultaneously to enter limit setting mode.

WIRE THE ENTRAPMENT PROTECTION DEVICES

Connect the entrapment protection device to the EYES EDGE terminal on the control

board.

• Close Photoelectric Sensor Entrapment Protection: Connect wires from the photoelectric sensors to the Inputs on the CLOSE EYES/INTERRUPT terminal.

• Close Edge Entrapment Protection: Connect wires from the entrapment protection device to the Inputs on the CLOSE EDGE terminal.

• Open Entrapment Protection: Connect wires from the entrapment protection device to the Inputs on the OPEN EYES/EDGE terminal.

ALARM

RESET

AC Power Switch

2 Press and hold one of the MOVE GATE buttons to move the gate to the

open or close limit.

3 Press and release the SET CLOSE or SET OPEN button

depending on which limit is being set.

4 Press and hold one of the MOVE GATE button to move the

ALARM

RESET

gate to the other limit.

5 Press and release the SET CLOSE or SET OPEN button depending on which

limit is being set.

CONNECT BATTERIES

1 Connect the battery wires to the

J15 plug on the control board.

2 Turn ON AC power to the

operator.

3 Turn ON the AC power switch on

the operator.

POWER WIRING

This operator can be wired for either 120 Vac or 240 Vac or a

solar panel (not provided). These instructions show a 120 Vac application. For information regarding a 240 Vac or solar application refer to the installation manual.

1 Turn off the AC power from the main

power source circuit breaker.

2 Run the AC power wires to the

operator.

3 Connect the green wire to the earth

ground rod and AC ground using a wire nut. NOTE: The earth ground

rod can be grounded to the chassis.

4 Connect the white wire to NEUTRAL

using a wire nut.

Black Wire

Red Wire

Jumper

EARTH GROUND ROD

1 Install the earth ground rod within 3 feet

of the operator.

2 Run wire from the earth ground rod to the

operator.

Check national and local codes for proper depth

6 Cycle the gate open and close. This automatically sets the force.

When limits are set properly the operator will automatically exit limit setting mode.

FINE TUNE THE FORCE

The FORCE DIAL on the control board is used for fine tuning the force. The force setting should be high enough that the gate will not reverse by itself nor cause nuisance interruptions, but low enough to prevent serious injury to a person. The force setting is the same for both the open and close gate directions.

1 Open and close the gate with the test buttons.

2 If the gate stops or reverses before reaching the fully

open or closed position, increase the force by turning the force control slightly clockwise.

3 Perform the “Obstruction Test” after every force setting adjustment (see below).

OBSTRUCTION TEST

1 Open and close the gate with the test buttons, ensuring that the gate is stopping at the proper open and close limit

positions.

2 Place a solid object between the open gate and a rigid structure. Ensure that the gate, the solid object, and the rigid

structure can withstand the forces generated during this obstruction test.

3 Run the gate in the close direction. The gate should stop and reverse upon contact with the solid object. If the gate

does not reverse off the solid object, reduce the force setting by turning the force control slightly counter-clockwise. The gate should have enough force to reach both the open and close limits, but MUST reverse after contact with a solid object.

4 Repeat the test for the open direction.

PROGRAMMING

ALARM

RESET

5 Connect the black wire to HOT using

a wire nut.

Junction Box

1 Press and release the LEARN

button (operator will beep and green XMITTER LED will light).

2 Press the remote control button for the

desired function. The operator will automatically exit learn mode (operator will beep and green XMITTER LED will go out) if programming is successful.