Life Fitness X35, X30 User Manual

Item Qty Description

67 mm Hex Head Bolt

21
12

4

Hex Head Nut

7

30 mm Hex Head Bolt

2

16 mm Phillips Screw

8.6 mm Lock Washer
Large Flat Washer

2

Large Wave Washer

2

Flat Washer

2

18.1 Lock

2
2
1
6
2
2
4

mm Washer
20 mm Hex Head Bolt
74

mm Hex Head Bolt

8mm

Phillips Screw

81.5 mm Hex Head Bolt

Large

8 mm Phillips Screw
12 mm Phillips Screw

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15

Assembly Guide:

Look for the number coded
hardware bags that match
the assembly sequence.

1)

3) 4)

4) 5)

7)6)

2)

8)

Hardware List

X305& X3 Cross-Trainer

6.

Lift the front end of the USER RIGHT PEDAL LEVER (K) to meet the USER RIGHT ROCKERARM CLEVIS (U). Secure the PEDAL LEVER to the ROCKERARM
CLEVIS using one 81.5 mm HEX HEAD BOLT(13) and one NUT (2). Tighten the BOLT and NUTsecurely. Repeat the procedure for the USER LEFT PEDAL
LEVER and ROCKERARM CLEVIS.

Position the front and back ROCKER ARM CLEVIS COVERS (S & T) over the USER RIGHT ROCKER ARM CLEVIS (U). Secure the CLEVIS COVERS using two
8 mm SCREWS (12). Tighten the SCREWS securely. Repeat the procedure for the USER LEFT ROCKERARM CLEVIS (V).

7.

Position theACCESSORY TRAY (W) over the DISPLAYCONSOLE MOUNTING PLATE (B) located at the top of the UPRIGHTTUBE ASSEMBLY(C) as shown.
Route the CONNECTOR (X) leading from the DISPLAY CONSOLE MOUNTING PLATE through the large hole in theACCESSORY TRAY BRACKET (Y). Secure
the ACCESSORY TRAY using two 8 mm SCREWS (14). Tighten the SCREWS securely.

Position the DISPLAY CONSOLE (Z) over the DISPLAY CONSOLE MOUNTING PLATE (B) located at the top of the UPRIGHTTUBE ASSEMBLY (C). Plug the
CONNECTOR (X) leading from the DISPLAY CONSOLE MOUNTING PLATE into the corresponding CONNECTOR in the back of the DISPLAY CONSOLE. Make
sure the CONNECTOR snaps into place. Push excess wire harness into the opening of the DISPLAYCONSOLE MOUNTING PLATE.

Plug the HEART RATE CONNECTOR (AA) leading from the ACCESSORY TRAY (W) into the corresponding CONNECTOR in the back of the DISPLAY
CONSOLE. Make sure the CONNECTOR snaps into place.

X3-5 Only:

DISPLAY CONSOLE. Make sure the CONNECTOR snaps into place.
Secure the DISPLAY CONSOLE to the DISPLAY CONSOLE MOUNTING PLATE (B) using four 12 mm SCREWS (15). Tighten the SCREWS securely.
CAUTION: Be careful not to pinch the wire harnesses when assembling the DISPLAY CONSOLE (Z) to the DISPLAY CONSOLE MOUNTING PLATE (B).

8.

Refer to the "Getting Started" section of the User Manual for proper location, stabilizing, and POWER ADAPTER instructions.

1.&2.
Levelers & Monocolumn

Plug the LOWER CONSOLE CONNECTOR (BB) leading from theACCESSORY TRAY (W) into the corresponding CONNECTOR in the back of the

6.
Pedal Lever &

9)

11)

10)

12)

13) 2)

14)

15)

3.

4 H C

F

E

2

3

Rocker Arm Assembly

T 12

G

1

A

J

V

4

5.

7.

2

U

S 13

12

10 706020 8030 9040 100 12050 110 130 140 150 160

Assembly Sequence

Tools required: Metric Socket set, Phillips Screwdriver, Metric Wrench set

1.

Position the base unit near the desired location for use (Refer to the "Getting Started" section of the User Manual for proper location). Locate and install the

two LEVELER FEET (A) into the front stabilizer as shown.

2.

With the DISPLAY CONSOLE MOUNTING PLATE (B) facing upward, lay the UPRIGHT TUBEASSEMBLY (C) on floor in front of BASE FRAME (D). Cut

the wire tie securing the LOWER WIRE HARNESS (E) to the front of the BASE FRAME. Connect the UPPER WIRE HARNESS (F) to the LOWER WIRE

HARNESS.

Position the UPRIGHT TUBEASSEMBLY(C) between the FRONT FRAME PLATES on the BASE FRAME (D). Feed any excess wire harness into the

BASE FRAME. Tilt the UPRIGHT TUBE ASSEMBLY into an upright position.Align the holes on the plates with the holes on the UPRIGHT TUBE

ASSEMBLY. Secure the UPRIGHT TUBE ASSEMBLY to the BASE FRAME using four 67 mm HEX HEAD BOLTS (1) and four NUTS (2). Leave BOLTS

loose at this time.

Using two 30 mm HEX HEAD BOLTS (3), secure the UPRIGHT TUBEASSEMBLY(C) to the backside of the SUPPORT PLATE on the BASE FRAME (D).

Tighten the BOLTS securely. Tighten the previous four HEX HEAD BOLTS (1) securely.

Position the right and left (H & J) over the . Secure the FRONT SHROUDS using nine 16 mm

(4). Tighten the SCREWS securely.

Locate the USER RIGHT PEDAL LEVER (K) and PEDAL (L) (marked with an “R”). Position the PEDAL above the PEDAL MOUNTING PLATE (M) and

3.

secure the PEDAL using six 16 mm SCREWS (4) and six LOCK WASHERS (5). Tighten the SCREWS securely. Repeat for the USER LEFT PEDALand

PEDAL LEVER.

FRONT SHROUDS FRONT FRAME PLATES (G) SCREWS

(G)

Pedals

L

M

4.
Rocker Arms

BQ

Pedals & Right Rear
Pedal Lever

2 K

K

4

12

V

11

S

R

T

Accessory Tray &
Console

Z

14

AA

BB

W

X3 Only

5

Y

X

B

15

Slide one LARGE FLAT WASHER (6) and one LARGE WAVE WASHER (7) onto the USER RIGHT PIVOT SHAFT (N). Slide the WASHERS fully over the

4.

PIVOT SHAFT until seated against the pre-installed stop ring.

Locate the USER RIGHT ROCKERARM ASSEMBLY (O) (Marked with an “R”). With the top handgrip facing the front of the unit (as shown), slide the

USER RIGHT ROCKERARM ASSEMBLY onto the USER RIGHT PIVOTSHAFT (N) until seated against the WASHERS (6 & 7). Secure the ROCKER

ARM ASSEMBLY to the PIVOT SHAFTusing one FLAT WASHER (8), LOCK WASHER (9), and 20 mm HEX HEAD BOLT(10). Tighten the BOLT securely.

Insert one ROCKER ARM END CAP (P) into the end of the ROCKER ARM SHAFT. Repeat the procedure for the USER LEFTROCKER ARM ASSEMBLY

(Q).

Position the rear end of the USER RIGHT PEDAL LEVER (K) near the USER RIGHT REAR CLEVIS (R). Position the end of the PEDAL LEVER between

5.

the clevis flanges. Align the holes and secure as shown using one 74 mm HEX HEAD BOLT (11) and one NUT (2).Tighten the BOLTand NUT securely.

Position one front and back CLEVIS COVER (S & T) over the USER RIGHT REAR CLEVIS (R). Secure the CLEVIS COVERS using two 8 mm SCREWS

(12). Tighten the SCREWS securely.

N 6 7

O

8 10

9 P

X BB AA

© 2005 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness is a registered trademarks of Brunswick

Corporation. Any use of this trademark, without the express written consent of Life Fitness is forbidden. 7954201 Rev A (06/05)

TOTAL-BODY ELLIPTICAL CROSS-TRAINERS | TREADMILLS | LIFECYCLE EXERCISE BIKES

5100 N.RIVER ROAD, SCHILLERPARK, ILLINOIS 60176

LIFEFITNESS.COM

Life Fitness offers a full line of premier fitness equipment for the home.

STAIRCLIMBERS | GYMSYSTEMS

®

Cross-Trainer

5

0

X3 & X3

ASSEMBLY

INSTRUCTIONS