Life Fitness OHDPR9 User Manual
OLYMPIC HEAVY DUTY POWER RACK 9’
(OHDPR9)
Part # 7671001
Rev. A
ASSEMBLY INSTRUCTIONS
Revision:12/10/031
PARTS LIST
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PART #
LEA7586101
LEA7586501
LEA7656601
LEA7656901
LEA7585801
LEA7586601
LEA7586901
LEA7588301
LEA7584401
LEA7584501
LEA7587501
LEA7587901
LEA7587801
LEA7589201
DESCRIPTION
LEFT UPRIGHT BASE
RIGHT UPRIGHT BASE
FRONT UPRIGHT
REAR UPRIGHT
CROSS SUPPORT
WEIGHT HORN UPRIGHT
REAR UPRIGHT SUPPOR T
CHIN-UP SUPPOR T
RIGHT ADJUSTMENT RACK
LEFT ADJUSTMENT RACK
WEIGHT HORN
LEFT BAR SUPPOR T
RIGHT BAR SUPPOR T
BAR CA TCH
QTY
1
1
2
2
2
2
1
1
2
2
10
1
1
2
KEY
15
16
17
18
19
20
21
22
23
24
25
26
27
PART #
LEA7596501
LEA3239318
LEA3239306
LEA3245201
LEA3102502
LEA3237505
LEA3239503
LEA7617301
LEA3102801
LEA3102802
LEA7601701
LEA3239317
LEA3105303
DESCRIPTION
BOTTOM UPRIGHT SUPPOR T
1/2 X 4-1/2” BOL T
1/2 X 1-1/2” BOL T
3/8 X 3-3/4” FLA T HEAD BOL T
1/2” FLA T W ASHER
1/2” INT TOOTH LOCK W ASHER
3/8” INT TOOTH LOCK W ASHER
1/2” PLASTIC DOME W ASHER
1/2” LOCK NUT
3/8” LOCK NUT
SWIVEL SPOTTER
1/2 X 4-1/4” BOL T
9/16” HOLE CAP
QTY
1
6
4
16
4
60
16
44
54
16
2
44
14
T ools Required for Assembly
* 3/4”, 9/16” wrench
* Ratchet with 3/4”, 9/16” socket
* 7/32” Allen W rench
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH
0
1/2 1/2 1/2 1/2 1/2 1/2
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
1
23456
2
17 1/2 X 1-1/2” BOL T
26 1/2 X 4-1/4” BOL T
16 1/2 X 4-1/2” BOL T
20
1/2” INT TOOTH
LOCK W ASHER
21
3/8” INT TOOTH
LOCK W ASHER
18 3/8 X 3-3/4” FLA T HEAD BOL T
22
1/2” PLASTIC
DOME W ASHER
19
1/2”
FLA T WASHER
23
1/2”
LOCK NUT
24
3/8”
LOCK NUT
3
FIGURE 1
4
23
20
22
26 1/2 X 4-1/4”
4
2
1
STEP 1:
• LOOSEL Y assemble the REAR UPRIGHT (4) to the LEFT UPRIGHT BASE (1) using two 1/2 X 4-1/4” BOLTS (26), two 1/2” PLASITC
DOME W ASHERS (22), two 1/2” INT TOOTH LOCK W ASHERS (20) and two 1/2” LOCK NUTS (23) as shown in FIGURE 1.
• LOOSEL Y assemble the REAR UPRIGHT (4) to the RIGHT UPRIGHT BASE (2) using two 1/2 X 4-1/4” BOLTS (26), two 1/2” PLASITC
DOME W ASHERS (22), two 1/2” INT TOOTH LOCK W ASHERS (20) and two 1/2” LOCK NUTS (23) as shown in FIGURE 1.
4
4
4
20
23
Use this set of holes for
assembly with PLA TFORM.
15
22
26 1/2 X 4-1/4”
Use this set of holes for
assembly without PLATFORM.
FIGURE 2
STEP 2:
• LOOSEL Y assemble the BOTTOM UPRIGHT SUPPOR T (15) to the REAR UPRIGHTS (4) using four 1/2 X 4-1/4” BOL TS (26), four
1/2” PLASITC DOME WASHERS (22), four 1/2” INT TOOTH LOCK WASHERS (20) and four1/2” LOCK NUTS (23) as shown in
FIGURE 2.
5
Loading...