Life Fitness OHDHR User Manual
OLYMPIC HEAVY DUTY HALF RACK
(OHDHR)
Part # 7671201
Rev. A
ASSEMBLY INSTRUCTIONS
Revision:12/12/031
PARTS LIST
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PART #
LEA7664801
LEA7665001
LEA7665101
LEA7584901
LEA7665501
LEA7586601
LEA7622401
LEA7663901
LEA7584401
LEA7584501
LEA7587501
LEA7587901
LEA7587801
LEA7605901
DESCRIPTION
LEFT UPRIGHT BASE
RIGHT UPRIGHT BASE
LEFT UPRIGHT SUPPOR T
REAR UPRIGHT
RIGHT UPRIGHT SUPPOR T
WEIGHT HORN UPRIGHT
LEFT BAR CA TCH
PULL-UP SUPPOR T
RIGHT ADJUSTMENT RACK
LEFT ADJUSTMENT RACK
WEIGHT HORN
LEFT BAR SUPPOR T
RIGHT BAR SUPPOR T
RIGHT BAR CA TCH
QTY
1
1
1
2
1
2
1
1
1
1
10
1
1
1
KEY
15
16
17
18
19
20
21
22
23
24
25
26
PART #
LEA7596501
LEA3239306
LEA3245201
LEA3102502
LEA3237505
LEA3239503
LEA7617301
LEA3102801
LEA3102802
LEA7601701
LEA3239317
LEA3105303
DESCRIPTION
BOTTOM UPRIGHT SUPPOR T
1/2 X 1-1/2” BOL T
3/8 X 3-3/4” FLA T HEAD BOL T
1/2” FLA T W ASHER
1/2” INT TOOTH LOCK W ASHER
3/8” INT TOOTH LOCK W ASHER
1/2” PLASTIC DOME W ASHER
1/2” LOCK NUT
3/8” LOCK NUT
SWIVEL SPOTTER
1/2 X 4-1/4” BOL T
9/16” HOLE CAP
QTY
1
4
8
4
52
8
48
52
8
2
48
6
T ools Required for Assembly
* 3/4”, 9/16” wrench
* Ratchet with 3/4”, 9/16” socket
* 7/32” Allen W rench
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH
0
1/2 1/2 1/2 1/2 1/2 1/2
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
1
23456
2
16 1/2 X 1-1/2” BOL T
25 1/2 X 4-1/4” BOL T
19
1/2” INT TOOTH
LOCK W ASHER
20
3/8” INT TOOTH
LOCK W ASHER
17 3/8 X 3-3/4” FLA T HEAD BOL T
21
1/2” PLASTIC
DOME W ASHER
18
1/2”
FLA T WASHER
22
1/2”
LOCK NUT
23
3/8”
LOCK NUT
3
FIGURE 1
4
22
19
1
21
4
2
25 1/2 X 4-1/4”
STEP 1:
• LOOSEL Y assemble the REAR UPRIGHT (4) to the LEFT UPRIGHT BASE (1) using two 1/2 X 4-1/4” BOL TS (25), two 1/2” PLASITC
DOME W ASHERS (21), two 1/2” INT TOOTH LOCK W ASHERS (19) and two 1/2” LOCK NUTS (22) as shown in FIGURE 1.
• LOOSEL Y assemble the REAR UPRIGHT (4) to the RIGHT UPRIGHT BASE (2) using two 1/2 X 4-1/4” BOL TS (25), two 1/2” PLASITC
DOME W ASHERS (21), two 1/2” INT TOOTH LOCK W ASHERS (19) and two 1/2” LOCK NUTS (22) as shown in FIGURE 1.
4
4
4
22
19
Use this set of holes for
assembly with PLA TFORM.
15
21
25 1/2 X 4-1/4”
26
Use this set of holes for
assembly without PLATFORM.
FIGURE 2
STEP 2:
• LOOSEL Y assemble the BOTTOM UPRIGHT SUPPOR T (15) to the REAR UPRIGHTS (4) using four 1/2 X 4-1/4” BOLTS (25), four
1/2” PLASITC DOME WASHERS (21), four 1/2” INT TOOTH LOCK W ASHERS (19) and four1/2” LOCK NUTS (22) as shown in
FIGURE 2.
• Insert six 9/16” HOLE CAPS (26) into the holes of the REAR UPRIGHTS (4) as shown in FIGURE 2.
5
Loading...