Life Fitness 8225 User Manual
8225 BICEP/TRICEP MACHINE
Part # 6845001
ASSEMBLY INSTRUCTIONS
Revision:11/2/991
IMPORTANT NOTES
Please note:
* Thank you for purchasing the LIFE FITNESS 8225 BICEP/TRICEP MACHINE. Please read
these instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your LIFE FITNESS customer service representative at (800) 328-9714.
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local LIFE FITNESS STRENGTH distributor or
call the LIFE FITNESS STRENGTH customer service department at (800) 328-9714.
5. Consult your physician before beginning any exercise program.
Tools Required for Assembly
* Rubber mallet or hammer
* 3/4” wrench, 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* 5/32”, 7/32” Allen wrenches
* Adjustable wrench
* Tape measure
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH
BOLT LENGTH RULER:
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
3 4 5
2
6
PARTS LIST
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PART #
6846003
6845503
6845103
6777703
6845303
6845703
6847002
6489902
6851401
6851501
6851901
6852001
3116101
6791102
6782301
6852301
6852601
3102917
3102953
3102901
DESCRIPTION
BASE
TOP BOOM
TOWER
TOWER BRACE
UPRIGHT
SEAT SUPPORT
PAD SUPPORT
2 X 7-1/4” PLATE
ARM CURL BAR
TRICEP ROPE
ARM CURL CABLE
TRICEP CABLE
4-1/2” PULLEY
SHROUD
63-1/2” GUIDE ROD
SEAT PAD
ARM PAD
1/2 X 4" BOLT
1/2 X 2-3/4" BOLT
3/8 X 1-1/4” BOLT
QTY
1
1
1
1
1
1
1
2
1
1
1
1
7
1
2
1
1
10
2
7
KEY
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
PART #
3102902
3102922
3202401
3102502
3102501
3102801
3102802
6480301
6412001
3103801
3103302
6266001
6714601
6214401
6214501
3108002
6382301
6703801
6189501
DESCRIPTION
3/8 X 2-1/4" BOLT
3/8 X 2-3/4” BOLT
3/8 X 1” BUTTON HEAD
1/2 “ WASHER
3/8" WASHER
1/2" LOCKNUT
3/8" LOCKNUT
3/8" FLANGE SPACER
3/8" SPRING PIN
5/16” SNAP HOOK
13/16” SHAFT COLLAR
WEIGHT STACK SHAFT
HEAD PLATE
SELECTOR PIN
WEIGHT PLATE
WEIGHT STACK CUSHION
PLATE BUSHING (10 COUNT)
WEIGHT STACK LABELS LBS.
WEIGHT STACK LABELS (1-25)
QTY
3
5
4
10
13
11
8
8
1
2
2
1
1
1
15
2
3
1
1
3
26
3
24
1
18 1/2 X 4”
FIGURE 1
STEP 1:
• LOOSELY assemble the BASE (1) to the TOWER (3) using two 1/2 X 4” BOLTS (18), two 1/2”
WASHERS (24), and two 1/2” LOCK NUTS (26) as shown in FIGURE 1.
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
3 4 5
4
6
18 1/2 X 4”
5
26
1
FIGURE 2
STEP 2:
• LOOSELY assemble the UPRIGHT (5) to the BASE (1) using four 1/2 X 4” BOLTS (18), two 1/2”
WASHERS (24), and four 1/2” LOCK NUTS (26) as shown in FIGURE 2.
13
2
28
3/8 X 2-3/4” 22
27
28
FIGURE 3
STEP 3:
• SECURELY assemble three 4-1/2” PULLEYS (13) to the TOP BOOM (2) using three 3/8 X 2-3/4”
BOLTS (22), six 3/8” FLANGE SPACERS (28), and three 3/8” LOCK NUTS (27) as shown in FIGURE 3.
5
Loading...