Life Fitness 8115 User Manual
8115 FLAT & INCLINE BENCH
Part # 6791801
ASSEMBLY INSTRUCTIONS
Revision:7/20/981
IMPORTANT NOTES
Please note:
* Thank you for purchasing the LIFE FITNESS 8115 FLAT & INCLINE BENCH. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled on a
flat, level surface to assure its proper function.
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your LIFE FITNESS customer service representative at (800) 328-9714.
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local LIFE FITNESS STRENGTH distributor or
call the LIFE FITNESS STRENGTH customer service department at (800) 328-9714.
5. Consult your physician before beginning any exercise program.
Tools Required for Assembly
* Rubber mallet or hammer
* 3/4” wrench, 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH
BOLT LENGTH RULER:
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
3 4 5
2
6
PARTS LIST
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
PART #
6651703
6700503
6712803
6697203
6624202
6624302
6651602
6780001
6780301
3202106
3202107
3102917
3102910
DESCRIPTION
REAR UPRIGHT
BENCH FRAME
ADJUSTABLE SLEEVE
BASE TUBE
LEFT BACK PAD ANGLE
RIGHT BACK PAD ANGLE
2 X 15-1/2” PLATE
SEAT PAD
BACK PAD
1/2 X 9-1/2” BOLT
1/2 X 6-1/2” BOLT
1/2 X 4” BOLT
1/2 X 3” BOLT
QTY
1
1
1
1
1
1
2
1
1
1
1
2
2
KEY
14
15
16
17
18
19
20
21
22
23
24
25
PART #
3202101
3102901
3102502
3102501
3102801
3102804
6406401
6619301
6653101
6412001
3120701
3118401
DESCRIPTION
1/2 X 1-1/4” BOLT
3/8 X 1-1/4” BOLT
1/2” WASHER
3/8” WASHER
1/2” LOCK NUT
1/2” LOW HEIGHT NUT
HINGE TAB
U-PIN
1/2” SPACER
3/8” SPRING PIN
1/2” PAL NUT
4” VINYL CAP
QTY
2
4
6
6
5
3
2
1
1
1
1
1
22
2
21
24
25
FIGURE 1
STEP 1:
• Assemble one U-PIN (21) to the BENCH FRAME (2) using one 1/2” SPACER (22) and one 1/2” PAL NUT (24) as shown in
FIGURE 1.
• Slide one 4” VINYL CAP (25) onto the U-PIN (21) as shown in FIGURE 1.
3
Loading...