Life Fitness 8105 User Manual
8105 SMITH PRESS
ASSEMBLY INSTRUCTIONS
Part # 6787901 Revision: 06/18/981
IMPORTANT NOTES
Please note:
* Thank you for purchasing the LIFE FITNESS 8105 SMITH PRESS. Please read these instructions
thoroughly and keep them for future reference. This product must be assembled on a flat, level
surface to assure its proper function.
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your LIFE FITNESS customer service representative
at (800) 328-9714.
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local LIFE FITNESS STRENGTH distributor or
call the LIFE FITNESS STRENGTH customer service department at (800) 328-9714.
5. Consult your physician before beginning any exercise program.
Tools Required for Assembly
* Rubber mallet or hammer
* 3/4” wrench, 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* 3/16, 1/4, 5/16” Allen wrench
* Adjustable wrench
* Tape measure
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH
BOLT LENGTH RULER:
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
3 4 5
2
2
6
PARTS LIST
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PART #
6712002
6711402
6711203
6708901
6711601
6711701
6710201
6710102
6710503
6710403
6787301
6709001
6709901
6709603
6675501
DESCRIPTION
BEARING HOUSING
SAFETY STOP
LOWER SUPPORT
SLEEVE ASSEMBLY
LEFT SAFETY HOOK
RIGHT SAFETY HOOK
SMITH BAR
BAR STOP
LEFT UPRIGHT
RIGHT UPRIGHT
UPPER SUPPORT
CHROME ANGLE
80” GUIDE ROD
COUNTER WEIGHT
PLATE HOLDER
26
QTY
2
2
1
2
1
1
1
2
1
1
1
2
2
2
6
KEY
16
17
18
19
20
21
22
23
24
25
26
27
28
29
PART #
3102937
3102917
3102933
3103003
3102502
3102801
3102802
3203001
3203002
3202901
6708501
3116101
6714501
6695801
DESCRIPTION
1/2 X 4-1/2” BOLT
1/2 X 4” BOLT
3/8 X 2” BOLT
5/8 X 1-1/4” SHOULDER BOLT
1/2” WASHER
1/2” LOCK NUT
3/8” LOCK NUT
2” SHAFT COLLAR
1” SHAFT COLLAR
1-1/2” THRUST BEARING
CABLE ASSEMBLY
4-1/2” PULLEY
8 X 1” GLIDE
2-1/2” OD RUBBER BUMPER
QTY
8
16
2
2
18
24
2
2
4
2
2
2
4
2
28
14
28
FIGURE 1
STEP 1:
• SECURELY
• Attach two 8 X 1” GLIDES (28) to both ends of two COUNTER WEIGHTS (14) as shown in FIGURE 1.
thread one end of the CABLE ASSEMBLY (26) into each of the two COUNTER WEIGHTS (14) as shown in FIGURE 1.
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
3 4 5
3
6
14
14
9
10
FIGURE 2
STEP 2:
• CAREFULLY lower one COUNTER WEIGHT (14) down into the LEFT UPRIGHT (9) & RIGHT UPRIGHT (10) until it bottoms
out as shown in FIGURE 2.
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
3 4 5
4
6
1/2 X 4-1/2” 16
15
3
21
9
10
1/2 X 4-1/2” 16
15
FIGURE 3
STEP 3:
• LOOSELY assemble the LOWER SUPPORT (3) and two PLATE HOLDER (15) to the LEFT & RIGHT UPRIGHTS (9& 10)
using four 1/2 X 4-1/2” BOLTS (16) and four 1/2” LOCK NUTS (21) as shown in FIGURE 3.
5
21
20
10
15
9
1/2 X 4” 17
FIGURE 4
STEP 4:
• SECURELY assemble four PLATE HOLDERS (15) to the LEFT & RIGHT UPRIGHTS (9 & 10) using eight 1/2 X 4” BOLTS
(17), eight 1/2” WASHERS (20), and eight 1/2” LOCK NUTS (21) as shown in FIGURE 4.
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
3 4 5
6
6
Loading...