662101 GLUTE/SQUAT OPTION
Rev B
ASSEMBLY INSTRUCTIONS
1Part # 7046901
Revision: 07/31/01
IMPORTANT NOTES
WELCOME TO THE WORLD OF Serious steel!
Please note:
* Thank you for purchasing the Parabody 662101 Glute/Squat Option. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at (800) 328-9714.
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
1. Inspect equipment daily . Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury .
4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at (800) 328-9714.
T ools Required for Assembly
* Rubber mallet or hammer
* 3/4” wrench
* Ratchet with 3/4” socket
* Adjustable wrench
* T ape measure
Bolt Length Ruler
NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOL T LENGTH RULER:
1/2 1/2 1/2 1/2 1/2 1/2
0
1
BOLT LENGTH
2
345
2
6
PARTS LIST
KEY
1
2
3
4
PART #
6748802
6748702
6740002
6016401
DESCRIPTION
FOOT PLA TE
SQUA T BAR
GLUTE KICK
ROLLER P AD
QTY
1
1
1
2
KEY
5
6
7
PART #
6670701
3102918
3102801
DESCRIPTION
NON-SKID STRIP
1/2 X 3-1/4” BOLT
1/2” LOCK NUT
QTY
1
2
2
1
7
PRESS
BASE
6 1/2 X 3-1/4”
FIGURE 1
STEP 1
• Swing the PRESS SEAT over 90° to install FOOT PLATE (1). See FIGURE 1.
• SECUREL Y attach the FOOT PLATE (1) to the PRESS BASE using two 1/2 X 3-1/4” BOLTS (6) and two 1/2” LOCK NUTS (7) as
shown in FIGURE 1.
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
3
6
PRESS
ARM
2
4
FIGURE 2
STEP 2
• Slide two ROLLER PADS (4) over the SQUAT BAR (2). See FIGURE 2. Space PADS out equally to support back of neck.
(Optional : SQUAT BAR may be used without ROLLER PADS.)
• Insert SQUAT BAR (4) into the hole on the PRESS ARM as shown.
PRESS
ARM
2
FIGURE 3
STEP 3
• Insert other end of SQUAT BAR (2) into the PRESS ARM. See FIGURE 3.
• Rotate SQUAT BAR (2) 90° to hold SQUAT BAR (2) in PRESS ARM. See FIGURE 3.
4
PRESS
ARM
3
5
FIGURE 4
STEP 4
• Attach one NON-SKID STRIP (5) to the GLUTE KICK (3) as shown in FIGURE 4.
• Insert GLUTE KICK(3) into the hole on the PRESS ARM as shown.
PRESS
ARM
3
FIGURE 5
STEP 5
• Rotate GLUTE KICK (3) 90° to hold GLUTE KICK (3) in PRESS ARM. See FIGURE 5.
Thank you for purchasing the P ARABODY 662101 GLUTE/SQUA T OPTION. If unsure of proper use of
equipment refer to the 662101 OPERA TION GUIDE or call your local P ARABODY distributor or call the
P ARABODY customer service department at (800) 328-9714.
5
Loading...