Life Fitness 360101 User Manual
Serious Steel
1360101 375 LEG PRESS ADAPTER KITi
Part # 6837701
ASSEMBLY INSTRUCTION
1
Eevision: 07/06/99
]IMPORTA~, ,T N~)TES
1
There is a risk assumed by individuals who use this type of equipment. To minirrrize risk, please
follow these rules:
1. Consult your physician before beginning any exercise program.
2. Inspect equipment daily. Tio~hten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
Do not allow minors or children to play on or around this equipment.
3.
Exercise with care to avoid injury.
4.
If un~fire of proper use of equipment, call your local Parabody distributor or call the "
5.
Parabody customer service department at (800) 328-9714.
Please note:
* Thank you for purchasing the Parabody 360101 Leg Press Adapter Kit. Please read these
instructions thoroughly and keep them for future reference. This product faust be assembled
on a flat, level surface to assure its proper function.
We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
*
water. Touch-up paint can be purchased from your Parabody customer service representative
at (800) 328-9714.
! TooI’s Required for Assembly]
* Rubber mallet or hammer
* 3/4" wrench
* 9/16" wrench
* Ratchet with 3/4" and 9/16" sockets
* Adjustable wrench
* Tape measure
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH RULER:
BOLT LENGTH
PARTS LIST
PART# DESCRIPTION
6838003 FRON~FLEG
6693902
6838103 ’ BASE CONNECTION
" ~
STEP 1
¯ Slidetwo2" SQ. COVERCAPS (6) over the FRONT LEG
3116i01 3-V2"eULLZY
5
6405201 2" SQ. END CAP
6
6-~700~ 2" SQ. COVER CAP
7
68~2701 ’
8
3102501 3/8" %VASHER
NOTE: The LEG PRESS ATTACHMENT (832101) must be assembled before connecting it to the
(I) as sho~vn in FIGURE
Pig I .FY BRACKET
2" SQ. r~UBB~BUM~ZR
PARABODY 375 ttOME GYI~I
QIY
1 9 3102802
1 i0 3102933
2
1 ~
2 14
1 15 ’3’102502
6 16 3102801
KEY PART#
12’ 3102937
6837801
6837901
DESCRIPTION
3/8" LOCKNUT
3/8 X 2" BOLT
1/2X3"BOLT ’ ’ ’
lnx
PRLMARY CABLE
LEG PRESS CABLE
I/2" WASHER
.... I~2" LOCK ~
FIGURE 1
STEP 2
¯
~
Slide one 2" SQ. END CAF (5) into the BASE CONNEC
FIGURE 2
STEP 3
¯ Attachone 2" SQ, RUBBER BUMPER (7) tothe top ofthePULLEY
BRACKET (2) as shown in FIGURE
shown in FIGURE 2.
FIGURE 3
3
STACK GUARD
BASE
~ 1/2 WASHER
FIGURE 4
STEP 4
¯
Remove two 1/2 X 4" BOLTS, two 1/2" WASHERS, and two 1/2" LOCK NUTS from the BASE and STACK GUARD as shown in
FIGURE 4. (NOTE: Discard the 1/2 X 4" BOLT.)
1/2 X 4" BOLT
BASE
,STACK GUARD
FIGURE 5
I/2X4-1/2"
STEP 5
¯
Securely fasten the FRONT LEG (I) and the BASE CONNECTION (3) to the BASE and STACK GUARD using two 1/2 X 4-1/2’"
BOLTS (12) and two previously removed 1/2" LOCKNUTS. See FIGURE
[ 1/2 [
I
1/2
[
2
1/2
[ 1/2 [ 1/2 [
3 4 5 6
4
1/2
Loading...