Page 1
Technical data
Hydraulic crawler crane
HS 895 HD
Page 2
Dimensions
Basic machine with undercarriage
2445
R 9760
3650
1700
17380
7945
9360
10000
3975
1720
R 6360
1810
3950
110 0
5480
3675
1610
620
6800
Operating weight
The operating weight includes the basic machine with HD undercarriage, 2 main winches 350 kN including wire ropes (150 m)
and 20 m main boom, consisting of A–frame, boom foot
(7 m), boom head (7 m) and boom section (6 m), 55.1 t basic
counterweight, 1100 mm track pads and 60 t hook block.
Total weight approx. 172.2 t
Ground pressure
Ground bearing pressure 0.98 kg/cm
2
Equipment
Main boom (No. 2220) max. length 84.2 m
Fixed jib (No. 1008) 11 m - 26 m
Modular designed equipment for operation as crane, with dragline or
clamshell.
For dragline operation, a rotating fairlead is fitted into the boom foot.
This minimizes the rope angle to drum, which results in lower rope
wear.
Remarks
1. The lifting capacities stated are valid for lifting operation only
(corresponding with crane classification according to F.E.M.
1.0 01, cr ane grou p A1).
2. Crane standing on firm, horizontal ground.
3. The weight of the lifting device (hoisting ropes, hook block,
shackle etc.) must be deducted from the gross lifting capacity
to obtain a net lifting value.
4. Additional equipment on boom (e.g. boom walkways, auxiliary
jib) must be deducted to get the net lifting capacity.
5. For max. wind speed please refer to lift chart in operator‘s cab
or manual.
6. Working radii are measured from center of swing and under
load.
7. The lifting capacities are valid for 360 degrees of swing.
8. Calculation of stability under load is based on ISO 4305
Table 1 + 2, tipping angle 4°.
9. The structures are calculated according to F.E.M. 1.001 - 1998
(EN 13001-2 / 2004).
2 HS 895 HD
Page 3
Transport dimensions and weights
Basic machine and boom (No. 2220.xx)
Basic machine
with A-frame, 2 x 350 kN winches including wire ropes (150 m), without
3410
970
crawlers, boom foot, basic and carbody counterweight
Width 3500 mm
Weight including jack-up system (1.7 t) 60700 kg
3250
7420
6250
12125
9360
3650
1610
2500
2420
2420
Crawler 2x
Track pads 1100 mm
Width 1450 mm
Weight* 25510 kg
Boom foot (No. 2220.30)
Width 2420 mm
Weight* 3720 kg
Boom section (No. 2220.24) 3 m
Width 2420 mm
Weight* 1030 kg
Boom section (No. 2220.24) 6 m
Width 2420 mm
Weight* 1630 kg
2420
11950
3220
7950
*) Including carbon fibre pendant strap, without auxiliary equipment
Boom section (No. 2220.22) 11.7 m
Width 2420 mm
Weight* 2380 kg
Boom head
Width 2420 mm
Weight* 4250 kg
1) Polyamide sheaves
1)
(No. 2220.24)
HS 895 HD 3
Page 4
Transport dimensions and weights
Fixed jib (No. 1008.xx)
Fixed jib head (No. 1008.20)
1100
6460
Width 1095 mm
Weight* 950 kg
6140
3140
6950
*) Including pendant ropes
Counterweight
5480
5480
1050
1050
1810
1110
340
Fixed jib section (No. 1008.17) 6 m
Width 1200 mm
Weight* 455 kg
Fixed jib section (No. 1008.17) 3 m
Width 1200 mm
Weight* 270 kg
Fixed jib foot with A-frame (No. 1008.20)
Width 2700 mm
Weight* 2350 kg
Counterweight 1x
Width 1660 mm
Weight 13200 kg
Counterweight 2x
Width 1660 mm
Weight 10600 kg
1360
Hooks
2600
2200
1050
4500
500
510
1050
1150
580 - 720
Counterweight (optional 8x) 4x
Width 1480 mm
Weight 5100 kg
Counterweight optional 2x
Width 1200 mm
Weight 13500 kg
200 t hook block – 3 sheaves
Width 480 mm
Weight 2600 kg
120 t hook block – 2 sheaves
Width 400 mm
Weight 1400 kg
35 t single hook
Width 400 580 720 mm
Weight 400 800 1200 kg
4 HS 895 HD
Page 5
Technical description
Engine
Power rating according to ISO 3046, 670 kW (898 hp) at 1900 rpm
Engine type
Fuel tank
Engine complies with NRMM exhaust certification EPA / CARB Tier 2.
MAN D 2842 LE
950 l capacity with continuous level
indicator and reserve warning
Hydraulic system
The main pumps are operated by a distributor gearbox. Axial piston
displacement pumps work in closed and open circuits supplying
oil only when needed (flow control on demand). To minimize peak
pressure an automatically working pressure cut-off is integrated.
This spares pumps and saves energy. The hydraulic oil is cleaned
through electronically controlled pressure and return filters.
Possible contamination is signaled in the cabin. The use of synthetic
environmentally friendly oils is possible. Ready made hydraulic retrofit
kits are available to customize requirements e.g. powering casing
oscillators, VM–vibrators, hydraulic grabs, fixed leaders etc.
Working pressure
Oil tank capacity
max. 350 bar
136 0 l
Main winches
Winch options:
Line pull (nom. load)
Rope diameter
Drum diameter
Rope speed
With change gear box
Rope capacity 1st layer
The winches are outstanding in their compact design and easy
assembly. Clutch and braking functions on the free-fall system are
provided by a compact designed, low wear and maintenance-free
multi–disc brake.
The drag and hoist winches use pressure controlled, variable flow
hydraulic motors. This system features sensors that automatically
adjust oil flow to provide max. winch speed depending on load.
Option:
Auxiliary winch
Tagline winch
70 kN in boom foot
70 kN with free fall
30 kN with free fall
350 kN
36 mm
830 mm
0-77 m/min
0-157 m/min
46.9 m
Crawlers
Boom winch
Line pull max. 150 kN
Rope diameter
Boom up
160 sec. from 15° to 86°
24 mm
Swing
Consists of rollerbearing with external teeth for lower tooth flank
pressure, fixed axial piston hydraulic motor, spring loaded and
hydraulically released multi–disc holding brake, planetary gearbox and
pinion. Swing speed from 0 – 3.6 rpm continuously variable, selector
for 3 speed ranges to increase swing precision.
Standard:
Second swing drive
Option:
Third swing drive
Noise emission
Noise emissions correspond with 2000/14/EC directive on noise
emission by equipment used outdoors.
The track width of the undercarriage is changed hydraulically.
Propulsion through axial piston motor, hydraulically released spring
loaded multi–disc brake, maintenance-free crawler tracks, hydraulic
chain tensioning device.
Track pads
Drive speed (2-speed hydraulic motor)
2nd gear 1.40 km/h
Option:
s¬ *ACKUP¬SYSTEM
s¬ 3ELFASSEMBLY¬SYSTEM
1st gear 0.75 km/h
110 0 mm
Control
The control system – developed and manufactured by Liebherr – is
designed to withstand extreme temperature changes and the rough
heavy duty tasks common in the construction industry. Complete
machine operating data are shown on a high resolution display. The
crane is equipped with proportional control for all movements, which
can be carried out simultaneously.
On request, Liebherr also offers special custom designed control
systems for free-fall winches.
Operation:
Left joy stick for boom winch and swing, right two directional levers
for winch I and II. Crawler control is actuated with the two central foot
pedals. Additionally, hand levers can be attached to the pedals.
Options:
s¬ 3PECIAL¬DEMOLITION¬CONTROL¬SYSTEM¬
s¬ -$%¬-ACHINE¬DATA¬RECORDING
s¬ 0$%¬0ROCESS¬DATA¬RECORDING
s¬ '3-¬MODEM
HS 895 HD 5
Page 6
Equipment (main boom No. 2220.xx and 55.1 t counterweight)
Casing oscillator
Casing oscillator*
Winch options 2 x 350 kN
Line speed 1st gear 0–77 m/min
(with change gear box) 0–157 m/min
Drilling diameter 3300 mm
Max. chisel weight 18 t
*) Load chart for duty cycle operation see page 8
6 HS 895 HD
Free-fall winches with maintenance-free, spring loaded multi-disc
brake working in an oil bath. Simultaneous working of both winches is
assured through our hydraulic system.
Hydraulic supply for casing oscillator
q = 2x 350 l/min
P = 300 bar max.
Mechanical connection casing oscillator on undercarriage.
Automatic operation for one- and two-rope grabs (optional). During the
drilling process the engine power can be freely divided between casing
oscillator and hoisting winches as required.
Page 7
Equipment (main boom No. 2220.xx and 55.1 t counterweight)
Dynamic soil compaction
Capacities in metric tons for boom lengths (25.7 m - 43.4 m)
Boom length
Radius (m) 25.7 m 31.7 m 37.4 m 43.4 m
tttt
9 40404038
10 40 38 36 34
11 35 35 32 31
12 32 32 30 28
Max. capacities in metric tons do not exceed 75% of tipping load.
All loads given are max. values and must not be exceeded. They are
only permitted in two-rope automatic operation and are valid for work
on a surface with max. inclination of 1%.
Lifting heights must not exceed 30 m.
HS 895 HD 7
Page 8
Load chart for duty cycle operation (main boom No. 2220.xx)
55.1 t counterweight
Capacities in metric tons for boom lengths (20 m - 58.1 m) - with 350 kN winches
Boom length (m)
Radius 20 23 25.7 28.7 31.7 34.7 37.4 40.4 43.4 46.4 49.1 52.1 55.1 58.1 Radius
(m) tttttttttttttt (m)
5.6 49.2 5.6
6 49.2 49.2 6
7 49.2 49.2 49.2 49.2 49.2 49.2 7
8 49.2 49.2 49.2 49.2 49.2 49.2 49.2 49.2 49.2 8
9 49.2 49.2 49.2 49.2 49.2 49.2 49.2 49.2 49.2 44.2 36.3 31.7 27.4 9
10 49.2 49.2 49.2 49.2 49.2 49.2 49.2 49.2 49.2 44.2 36.3 31.7 27.4 24.8 10
12 49.2 49.2 49.2 49.2 49.2 49.2 49.2 46.8 45.8 42.7 36.3 31.7 27.4 24.8 12
14 49.2 49.2 49.2 49.2 49.2 49.2 47.4 44.6 40.8 37.4 32.1 29.2 26.5 24.5 14
16 42.3 42.3 42.5 42.4 42.4 42.2 42.2 40.8 37.0 33.5 29.2 26.6 24.8 23.0 16
18 35.9 35.9 36.2 36.1 36.0 35.8 35.8 35.6 34.2 29.7 26.8 24.8 23.5 21.8 18
20 31.0 31.0 31.3 31.2 31.1 30.9 30.9 30.7 29.4 26.9 25.1 23.3 21.8 20.3 20
22 27.1 27.4 27.3 27.2 27.0 27.0 26.8 25.8 24.4 23.2 21.9 20.6 18.9 22
24 24.2 24.1 24.0 23.9 23.9 23.6 22.8 22.0 21.7 20.3 19.1 17.8 24
26 21.5 21.4 21.2 21.3 21.1 20.5 19.8 19.4 18.8 17.9 16.6 26
28 19.2 19.2 19.0 19.1 18.9 18.6 17.8 17.6 16.9 16.4 15.8 28
30 17.3 17.1 17.2 17.0 16.8 16.3 15.9 15.4 14.9 14.2 30
32 15.5 15.5 15.4 15.2 14.8 14.5 14.0 13.5 13.0 32
34 14.0 14.1 13.9 13.8 13.5 13.3 12.8 12.3 11.8 34
36 12.8 12.7 12.5 12.3 12.2 11.7 11.3 10.8 36
38 11.5 11.4 11.2 11.1 10.8 10.4 9.9 38
40 10.4 10.2 10.1 9.9 9.5 9.2 40
42 9.4 9.2 9.2 9.0 8.8 8.4 42
44 8.4 8.4 8.1 7.9 7.6 44
46 7.6 7.3 7.1 6.8 46
48 6.6 6.4 6.1 48
50 5.7 5.4 50
55 3.9 55
TLT 10532960 M99999 Vorab1
Maximum capacity in duty cycle operation with standard ropes
Line pull kN 350
Rope diameter mm 36
Minimum breaking load kN 1186
Line pull - 1-rope duty cycle operation t 30
Line pull - 2-rope duty cycle operation
1)
t49.2
1) Lifting a load exceeding the line pull of one winch is only allowed
if it can be ensured that each individual winch is not overloaded.
When working with a mechanical 2-rope grab the total load
to be lifted is limited by the line pull of one winch.
Rigging and ropes are part of the load.
2) Max. capacities in metric tons do not exceed 75% of tipping load.
Crane standing on firm, horizontal ground.
Capacities in duty cycle operation are for reference only and are not programmed in the LMI system.
All loads and counterweight configurations are max. values and must not be exceeded.
Weight of additional equipment on boom (e.g. walkways, hose drums etc.) must be deducted to get the net capacity.
8 HS 895 HD
Page 9
Dragline equipment (main boom
55.1 t counterweight
Capac itie s in metric ton s for boom lengths (25.7 m - 55.1 m) counterweight 55.1 t
C
K
J
E
D
Digging diagram
C = Radius / dumping radius
D = Max. digging radius = approx.
¬ ¬ #¬¬¬TO¬¬*¬¬+
E = Digging depth = approx.
40 - 50% of C
*¬ ¬(EIGHT¬TO¬CENTRE¬ROPE¬PULLEY¬
boom head
K = Length of dragline bucket
(according to manufacturer‘s
specification)
alpha C *¬ C *¬ C *¬ C *¬ C *¬ C *¬
45 21.1 19.7 29.1 25.3 24.0 22.3 29.3 28.0 17.8 33.6 32.3 14.0 37.6 36.3 11.3 41.9 40.5 8.8
40 22.5 18.0 26.5 27.1 21.9 20.1 31.5 25.6 15.9 36.1 29.4 12.5 40.4 33.1 9.9 45.0 36.9 7.5
35 23.8 16.2 24.5 28.7 19.6 18.5 33.4 22.9 14.5 38.3 26.3 11.2 43.0 29.6 8.8 47.9 33.1 6.4
30 24.9 14.3 22.9 30.1 17.3 17.2 35.1 20.1 13.4 40.3 23.1 10.2 45.2 26.0 7.9 50.4 29.0 5.6
25 25.9 12.2 21.7 31.3 14.8 16.1 36.5 17.2 12.5 41.9 19.7 9.5 47.1 22.1 7.1 52.5 24.6 4.9
Max. capacities in metric tons do not exceed 75% of tipping load.
Capacities in duty cycle operation are for reference only and are not programmed in the LMI system.
The size of the bucket has to be determined according to local conditions.
25.7 31.7 37.4 43.4 49.1 55.1
(m) (m) t (m) (m) t (m) (m) t (m) (m) t (m) (m) t (m) (m) t
No. 2220.xx)
Boom length (m)
TLT 10532960 M99999 Vorab1
Clamshell equipment (main boom
55.1 counterweight
C
1500
K
J
Working diagram
C = Radius / dumping radius
*¬¬ (EIGHT¬OF¬BOOM¬HEAD¬SHEAVE¬¬
centre above ground level
K = Length of clamshell (depending
on type and capacity of bucket)
Capac itie s in metric ton s for boom lengths (25.7 m - 55.1 m) counterweight 55.1 t
25.7 31.7 37.4 43.4 49.1 55.1
alpha C *¬ C *¬ C *¬ C *¬ C *¬ C *¬
(m) (m) t (m) (m) t (m) (m) t (m) (m) t (m) (m) t (m) (m) t
65 14.0 25.2 45.6 16.5 30.6 36.0 18.9 35.8 29.7 21.5 41.2 24.6 23.9 46.4 20.8 26.4 51.8 17.5
60 15.9 24.1 38.1 18.9 29.3 29.8 21.8 34.2 24.4 24.8 39.4 20.0 27.6 44.3 16.7 30.6 49.5 13.8
55 17.8 22.8 32.7 21.2 27.7 25.5 24.5 32.4 20.6 27.9 37.3 16.7 31.2 41.9 13.8 34.6 46.9 11.2
50 19.5 21.3 28.8 23.3 25.9 22.2 27.0 30.3 17.9 30.9 34.9 14.3 34.5 39.3 11.7 38.4 43.9 9.3
45 21.1 19.7 25.9 25.3 24.0 19.8 29.3 28.0 15.8 33.6 32.3 12.5 37.6 36.3 10.1 41.9 40.5 7.9
40 22.5 18.0 23.6 27.1 21.9 17.9 31.5 25.6 14.2 36.1 29.4 11.1 40.4 33.1 8.8 45.0 36.9 6.7
35 23.8 16.2 21.8 28.7 19.6 16.4 33.4 22.9 12.9 38.3 26.3 10.0 43.0 29.6 7.8 47.9 33.1 5.8
30 24.9 14.3 20.3 30.1 17.3 15.3 35.1 20.1 11.9 40.3 23.1 9.1 45.2 26.0 7.0 50.4 29.0 5.1
25 25.9 12.2 19.2 31.3 14.8 14.3 36.5 17.2 11.1 41.9 19.7 8.4 47.1 22.1 6.4 52.5 24.6 4.6
Max. capacities in metric tons do not exceed 66.7% of tipping load.
Capacities in duty cycle operation are for reference only and are not programmed in the LMI system.
No. 2220.xx)
Boom length (m)
TLT 10538305 M99999 Vorab1
HS 895 HD 9
Page 10
Lift crane operation
(main boom No. 2220.xx)
86° – 15°
75.1 t counterweight and 27 t carbody counterweight
Auxiliary jib 35 t
The maximum capacity of
the auxiliary jib is 35 t. The
corresponding load chart
is programmed in the LMI
system.
Main boom configuration (Table 1)
Configuration for boom lengths (20 m - 84. 2 m)
Length Amount of boom extensions
Boom foot 7.0 m
Boom section 3.0 m
Boom section 6.0 m
Boom section 11.7 m
Boom head 7.0 m
Boom length (m)
*) Additional counterweight allows self-erection of boom up to 84.2 m.
10 H S 895 HD
11111111111111111111111
11111111111
11 11111 11 11 11111 11
111122223333444455556
11111111111111111111111
20 23 25.0 28.7 31.7 34.7 37.4 40.4 43.4 46.4 49.1 52.1 55.1 58.1 60.8 63.8 66.8 69.8 72.5 75.5* 78.5* 81.5* 84.2*
Page 11
Load chart for lift crane operation (main boom No. 2220.xx)
55.1 t counterweight
Capacities in metric tons for boom lengths (20 m - 72.5 m) - with 350 kN winches
Boom length (m)
Radius 20 23 25.7 28.7 31.7 34.7 37.4 40.4 43.4 46.4 49.1 52.1 55.1 58.1 60.8 63.8 66.8 69.8 72.5 Radius
(m) ttttttttttttttttttt (m)
4.9 175.5 4.9
5 173.8 5
6 161.4 161.0 154.9 6
7 137.7 132.5 128.3 123.6 119.3 115.2 7
8 116.2 112.3 109.2 105.7 102.4 99.2 96.6 93.8 91.0 8
9 100.3 97.2 94.9 92.1 89.5 87.0 84.9 82.6 80.4 78.2 76.4 74.4 72.7 9
10 88.0 85.6 83.8 81.5 79.4 77.2 75.6 73.6 71.8 69.9 68.4 66.7 65.1 63.4 62.1 59.5 10
12 67.3 67.3 67.5 65.9 64.4 62.8 61.6 60.2 58.8 57.4 56.3 55.0 53.7 52.4 51.4 50.2 49.0 47.4 42.9 12
14 54.1 54.0 54.2 54.1 53.8 52.6 51.7 50.5 49.4 48.3 47.4 46.4 45.3 44.3 43.5 42.5 41.5 40.5 39.2 14
16 44.8 44.8 45.0 44.9 44.8 44.6 44.3 43.3 42.4 41.4 40.7 39.8 38.9 38.0 37.4 36.5 35.7 34.8 34.2 16
18 38.0 38.0 38.2 38.1 38.0 37.7 37.8 37.5 36.9 36.0 35.5 34.6 33.9 33.1 32.5 31.7 31.0 30.2 29.7 18
20 32.7 32.7 33.0 32.8 32.7 32.5 32.5 32.3 32.1 31.7 31.2 30.5 29.8 29.1 28.5 27.9 27.2 26.5 26.0 20
22 28.5 28.8 28.7 28.6 28.4 28.4 28.1 28.0 27.7 27.6 27.0 26.4 25.7 25.3 24.6 24.0 23.4 22.9 22
24 25.0 25.4 25.3 25.2 25.0 25.0 24.8 24.6 24.3 24.2 24.0 23.5 22.9 22.5 21.9 21.3 20.7 20.3 24
26 22.5 22.5 22.4 22.2 22.2 22.0 21.8 21.5 21.4 21.2 21.0 20.5 20.1 19.6 19.0 18.4 18.0 26
28 20.1 20.0 19.8 19.9 19.6 19.4 19.2 19.1 18.8 18.6 18.3 18.1 17.5 17.0 16.5 16.1 28
30 17.9 18.0 17.8 17.8 17.6 17.4 17.2 17.1 16.8 16.6 16.3 16.2 15.8 15.3 14.7 14.4 30
32 16.2 16.0 16.1 15.9 15.7 15.4 15.3 15.1 14.8 14.6 14.4 14.2 13.7 13.2 12.9 32
34 14.5 14.6 14.3 14.2 13.9 13.8 13.6 13.3 13.0 12.9 12.6 12.3 11.8 11.5 34
36 13.2 13.0 12.8 12.5 12.5 12.2 12.0 11.7 11.6 11.3 11.0 10.6 10.3 36
38 11.9 11.8 11.6 11.3 11.3 11.0 10.8 10.5 10.4 10.1 9.8 9.5 9.2 38
40 10.7 10.5 10.3 10.2 10.0 9.7 9.4 9.3 9.0 8.8 8.5 8.2 40
42 9.5 9.3 9.3 9.0 8.8 8.5 8.3 8.1 7.8 7.5 7.3 42
44 8.6 8.4
46 7.6 7.6 7.3 7.1 6.8 6.7 6.4 6.1 5.8 5.7 46
48 6.8 6.6 6.4 6.1 6.0 5.7 5.4 5.1 5.0 48
50 5.9 5.7 5.4 5.3 5.0 4.8 4.5 4.3 50
55 4.2 3.9 3.8 3.6 3.3 3.0 2.9 55
60 2.6 2.3 2.1 1.8 1.7 60
65 1.0 65
Above load chart is for reference only. For actual lift duty please refer to load chart in operator’s cab or manual.
8.4 8.1 7.9 7.6 7.5 7.2 6.9 6.6 6.5 44
TLT 901017914 - M 00000
HS 895 HD 11
Page 12
Load chart for lift crane operation (main boom No. 2220.xx)
75.1 t counterweight and 27 t carbody counterweight
Capacities in metric tons for boom lengths (20 m - 84.2 m) - with 350 kN winches
Boom length (m)
Radius 20 25.7 28.7 34.7 37.4 43.4 46.4 49.1 52.1 55.1 58.1 60.8 63.8 66.8 69.8 72.5 75.5 78.5* 84.2* Radius
(m) ttttttttttttttttttt (m)
5 200.0 5
6 192.7 197.1 194.4 6
7 179.6 168.3 162.3 151.3 146.9 7
8 152.9 143.8 139.3 130.9 127.3 120.1 116.7 111.1 8
9 132.3 125.2 121.6 115.0 112.4 104.2 103.5 101.1 98.5 93.9 88.2 9
10 116.2 110.8 107.8 102.4 100.2 95.4 93.1 90.9 88.7 86.6 83.8 73.1 68.7 64.5 10
12 89.2 89.4 87.6 83.7 82.2 78.6 76.8 75.4 73.5 72.0 70.4 66.6 62.5 58.7 55.3 50.6 47.3 49.8 41.3 12
14 72.0 72.2 72.1 70.4 69.3 66.5 65.1 64.0 62.7 61.4 59.9 58.9 57.7 53.8 50.5 46.3 43.2 47.2 39.8 14
16 60.0 60.2 60.1 59.8 59.7 57.4 56.2 55.3 54.2 53.2 52.1 51.1 50.0 49.0 47.1 43.3 40.1 45.2 38.5 16
18 51.1 51.4 51.2 50.9 50.9 50.2 49.2 48.5 47.5 46.6 45.7 45.0 43.9 43.0 42.1 40.9 37.8 39.7 37.5 18
20 44.3 44.6 44.5 44.1 44.1 43.7 43.5 43.0 42.1 41.3 40.5 39.9 39.1 38.2 37.3 36.7 35.7 35.4 33.8 20
22 39.2 39.1 38.8 38.8 38.4 38.1 38.0 37.7 37.0 36.2 35.6 34.9 34.2 33.5 32.7 32.0 31.5 30.3 22
24 34.8 34.7 34.4 34.4 34.0 33.7 33.7 33.4 33.2 32.6 32.1 31.4 30.7 30.0 29.4 28.7 28.2 27.1 24
26 31.1 31.1 30.8 30.8 30.4 30.1 30.0 29.8 29.6 29.3 29.0 28.4 27.8 27.1 26.7 25.9 25.4 24.4 26
28 28.0 27.8 27.8 27.3 27.1 27.0 26.7 26.5 26.2 26.1 25.8 25.2 24.6 24.1 23.6 23.0 22.0 28
30 25.3 25.1 25.2 24.8 24.5 24.4 24.1 23.9 23.6 23.5 23.2 22.9 22.3 21.9 21.4 20.8 19.9 30
32 22.9 22.9 22.5 22.2 22.2 21.9 21.7 21.4 21.3 21.0 20.7 20.4 20.0 19.5 18.9 18.0 32
34 20.9 20.9 20.5 20.3 20.2 19.9 19.7 19.4 19.3 19.0 18.8 18.5 18.3 17.7 17.2 16.3 34
36 19.2 18.8 18.5 18.5 18.2 18.0 17.7 17.6 17.3 17.0 16.7 16.6 16.2 15.7 14.8 36
38 17.6 17.3 17.0 16.9 16.7 16.4 16.2 16.0 15.7 15.5 15.2 15.0 14.8 14.3 13.5 38
40 15.9 15.6 15.6 15.3 15.1 14.8 14.7 14.4 14.1 13.8 13.7 13.4 13.1 12.3 40
42 14.6 14.4 14.3 14.1 13.8 13.5 13.4 13.1 12.9 12.6 12.4 12.1
44 13.4 13.2 13.2 12.9 12.7 12.4 12.3 12.0 11.8 11.5 11.3 11.0 10.8 10.1 44
46 12.2 12.2 11.9 11.7 11.4 11.3 11.0 10.8 10.5 10.3 10.0 9.7 9.2 46
48 11.2 11.0 10.8 10.5 10.4 10.1 9.8 9.5 9.4 9.1 8.8 8.3 48
50 10.1 9.9 9.6 9.5 9.2 9.0 8.7 8.5 8.2 8.0 7.5 50
55 8.0 7.7 7.6 7.4 7.1 6.8 6.7 6.4 6.1 5.6 55
60 6.1 5.8 5.6 5.3 5.1 4.9 4.6 4.1 60
65 4.2 4.0 3.8 3.6 3.3 2.8 65
70 2.7 2.4 2.2 1.7 70
75 1.4 1.2 75
*) with mid-point suspension
Above load chart is for reference only. For actual lift duty please refer to load chart in operator’s cab or manual.
11.9 11.1 42
TLT 901017914 - M 00000
12 HS 895 HD
Page 13
Working range - fixed jib (No. 1008.xx) 15° and 30°
Main boom 86° - 30°
m
ft
108
104
340
100
320
300
280
260
240
220
200
180
160
140
120
100
80
60
40
20
96
92
88
84
80
76
72
68
64
60
56
52
48
44
40
36
32
28
24
20
16
12
8
4
0
0
92 88 84 80 76 68 64 60 56 52 48 44 40 36 32 28 24 20 16 12 8 4 0 m72
30°
40°
50°
69.8 m
66.8 m
63.8 m
26m
60°
60.8 m
58.1 m
55.1 m
23m
20m
52.1 m
49.1 m
46.4 m
17m
14m
70°
43.4 m
40.4 m
37.7 m
11m
37.4 m
31.7 m
28.7 m
25.7 m
23 m
20 m
84°
86°
0 ft20406080100120140160180200220240260280300
Boom configuration for boom lengths (20 m - 69.5 m) - see table 1, page 10
Fixed jib configuration for fixed jib lengths (11 m - 26 m)
Length Amount of fixed jib extensions
Fixed jib foot 5.5 m111111
Fixed jib section 3.0 m 1 1 1
Fixed jib section 6.0 m 1122
Fixed jib head 5.5 m111111
Fixed jib length (m) 11 14 17 20 23 26
HS 895 HD 13
Page 14
Load chart - fixed jib (No. 1008.xx)
Offset 15°
Main boom 20 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
7.8 45.0
10 43.8 43.2
12 41.2 39.2 25.2
15 36.4 34.8 22.6 15.6
18 35.6 31.9 21.0 14.5
20 35.5 28.6 20.1 13.9
24 30.1 24.1 17.7 12.9
28 26.2 22.4 15.9 11.9
30 24.5 21.2 14.7 11.5
32 19.9 13.8 11.2
38 12.0 9.5
44 8.4
Main boom 46.4 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
9.6 23.0
11 35.3 23.0
14 31.9 29.1 23.1
17 30.2 28.2 21.9 14.8
20 29.8 27.9 21.1 14.3
28 26.7 27.2 19.4 13.0
36 17.9 18.3 16.9 12.0
44 12.5 12.9 13.6 11.1
50 9.6 10.0 10.7 10.2
55 8.0 8.7 9.3
60 7.0 7.6
65 6.2
Main boom 28.7 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
8.4 44.8
10 42.2 40.2
13 36.5 34.9 24.2
16 34.4 32.0 22.3 15.2
20 33.5 31.8 20.8 14.2
24 33.4 27.7 19.5 13.3
28 28.1 24.5 17.4 12.5
32 23.1 22.4 16.0 11.8
36 19.3 19.8 14.2 11.2
40 16.7 13.0 10.2
46 11.8 9.1
50 8.6
Main boom 49.1 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
9.8 23.0
12 33.1 30.6
14 31.3 28.4 21.3
17 29.8 27.5 21.8 14.7
20 29.3 27.3 21.1 14.2
28 26.5 27.0 19.5 13.1
36 17.8 18.2 17.3 12.1
44 12.4 12.8 13.5 11.2
48 10.4 10.7 11.4 10.7
55 7.5 7.9 8.6 9.1
60 6.9 7.5
70 4.8
Main boom 37.4 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
9 41.9
11 37.8 35.3
14 33.5 31.7 23.4
16 31.8 30.5 22.4 15.2
20 31.7 29.9 21.1 14.3
28 27.5 26.8 19.1 12.8
36 18.7 19.2 16.1 11.6
40 15.7 16.2 14.6 11.1
44 13.3 13.7 13.5 10.4
48 11.6 12.4 9.7
50 11.5 9.4
60 8.3
Main boom 55.1 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
10.2 23.0
12 31.8 29.4
15 29.4 26.5 22.2
18 28.5 26.1 21.4 14.4
20 28.2 26.1 21.0 14.1
28 25.6 25.9 19.5 13.1
36 17.2 17.7 17.9 12.2
44 11.8 12.2 13.0 11.3
55 7.0 7.4 8.0 8.6
60 5.4 5.7 6.4 6.9
65 5.0 5.5
75 3.2
Main boom 60.8 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
10.6 23.0
12 30.4 23.0
15 27.6 25.6 21.5
18 27.2 24.9 20.9 14.2
20 26.9 24.8 20.6 13.9
28 24.5 24.7 19.3 13.0
36 16.8 17.2 17.7 12.1
44 11.3 11.7 12.5 11.4
55 6.5 6.9 7.6 8.2
65 3.6 3.9 4.5 5.1
70 3.3 3.9
80 1.8
Capacities in metric tons with fixed jib (No. 1008.xx), 75.1 t counterweight + 27 t carbody counterweight. Above load chart is for reference only. For actual
lift duty please refer to load chart in operator‘s cab or manual.
14 HS 895 H D
Main boom 66.8 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
11 23.0
13 28.0 25.7
16 25.9 24.1 20.1
18 25.8 23.7 20.1 12.5
24 25.7 23.6 19.6 13.3
32 19.1 19.5 18.5 12.5
40 13.1 13.4 14.1 11.8
48 8.8 9.2 9.9 10.4
65 3.0 3.4 4.0 4.6
70 1.9 2.2 2.8 3.3
75 1.7 2.3
80 1.3
Main boom 69.8 m
Fixed jib length (m)
Radius 11 14 17 20
(m) t t t t
11.2 23.0
13 27.4 24.8
15 25.8 23.8 21.7
16 25.2 23.4 21.6 19.4
18 25.1 22.9 21.3 19.4
24 24.8 22.8 21.1 19.1
32 18.6 19.0 19.3 18.2
40 12.6 12.9 13.3 13.6
48 8.5 8.8 9.1 9.4
65 2.7 3.1 3.4 3.7
70 1.6 1.9 2.2 2.5
75 1.2 1.4
TLT 9510179 - M 00000
Page 15
Load chart - fixed jib (No. 1008.xx)
Offset 30°
Main boom 20 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
10.2 42.8
13 35.8 27.7
17 29.4 23.0 17.2
22 24.3 20.6 14.2 11.3
24 23.0 19.3 13.2 10.6
26 23.0 18.1 12.5 10.0
28 22.6 17.1 11.8 9.4
30 21.9 16.4 11.3 9.0
32 15.9 10.8 8.5
38 10.0 7.5
42 7.1
44 7.0
Main boom 46.4 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
12 30.1
14 27.8 25.6
18 26.9 24.5 17.3
22 26.9 23.3 16.2 12.0
30 24.6 21.5 13.5 10.3
38 16.7 17.2 11.9 9.0
42 13.9 14.4 11.3 8.5
46 11.7 12.1 10.8 8.1
50 9.7 10.2 10.4 7.7
55 8.1 9.0 7.3
60 7.2 7.1
65 6.3
Main boom 28.7 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
10.8 37.5
13 34.1 28.6
17 30.6 24.4 17.6
22 27.3 22.3 15.0 11.6
26 24.5 20.2 13.3 10.4
30 23.0 18.3 12.2 9.5
34 21.3 16.8 11.3 8.7
38 17.8 16.0 10.6 8.1
40 15.7 10.3 7.8
44 10.0 7.4
46 9.8 7.2
50 7.0
Main boom 49.1 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
12.2 29.1
15 26.5 24.6
19 26.2 23.9 17.0
24 26.2 22.8 15.5 11.5
30 24.4 22.0 13.7 10.4
38 16.6 17.1 12.1 9.1
42 13.8 14.3 11.5 8.6
46 11.6 12.0 11.0 8.2
50 9.7 10.1 10.6 7.8
55 7.6 8.0 8.9 7.4
65 5.5 6.3
70 4.9
Main boom 37.4 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
11.2 34.7
14 31.2 27.8
18 29.6 24.4 17.2
22 28.8 22.5 15.5 11.8
26 26.1 21.5 13.9 10.7
30 24.0 19.5 12.8 9.8
34 20.9 18.0 11.8 9.1
38 17.5 16.8 11.1 8.4
42 14.7 15.2 10.5 7.9
46 12.8 10.1 7.5
50 9.9 7.2
55 7.0
Main boom 55.1 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
12.6 27.3
15 25.7 23.2
19 25.1 23.0 17.0
24 25.1 23.0 15.8 11.5
30 23.9 22.1 14.1 10.5
38 16.1 16.7 12.5 9.3
42 13.3 13.8 11.9 8.9
46 11.1 11.5 11.3 8.4
50 9.2 9.6 10.5 8.0
60 5.5 5.9 6.7 7.3
70 3.8 4.5
75 3.3
Main boom 60.8 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
13 25.5
15 24.5 21.8
19 23.7 21.7 17.1
24 23.7 21.7 16.0 11.5
30 23.0 21.6 14.5 10.6
38 15.7 16.3 12.8 9.5
46 10.6 11.1 11.7 8.6
50 8.8 9.2 10.1 8.2
60 5.1 5.5 6.3 7.0
65 3.7 4.0 4.8 5.5
75 2.3 3.0
80 1.9
Capacities in metric tons with fixed jib (No. 1008.xx), 75.1 t counterweight + 27 t carbody counterweight. Above load chart is for reference only. For actual
lift duty please refer to load chart in operator‘s cab or manual.
Main boom 66.8 m
Fixed jib length (m)
Radius 11 14 20 26
(m) t t t t
13.4 23.0
16 23.1 20.6
20 22.6 20.6 16.9
24 22.6 20.6 15.9 11.4
30 21.9 20.4 14.6 10.7
38 15.0 15.5 13.1 9.7
46 10.1 10.6 11.6 8.8
50 8.2 8.7 9.6 8.5
60 4.6 5.0 5.8 6.6
70 1.9 2.3 3.0 3.7
75 1.9 2.6
80 1.5
Main boom 69.8 m
Fixed jib length (m)
Radius 11 14 17 20
(m) t t t t
13.6 22.9
16 22.4 19.9
18 22.0 19.9 18.2
20 21.9 19.9 18.2 16.6
22 21.9 19.9 18.2 16.2
30 21.4 19.9 17.9 14.6
38 14.5 15.0 15.5 13.2
46 9.8 10.3 10.7 11.1
50 7.9 8.4 8.9 9.3
60 4.3 4.7 5.2 5.6
70 1.7 2.0 2.4 2.8
75 1.3 1.6
TLT 9510179 - M 00000
HS 895 HD 15
Page 16
Self-assembly system
Unloading of basic machine
Unloading and assembly of crawlers
Unloading and assembly of carbody counterweight (option)
Unloading and assembly of counterweight
Assembly of boom foot
Unloading and assembly of boom
Liebherr-Werk Nenzing GmbH
P.O. Box 10, A-6710 Nenzing/Austria
Tel.: +43 50809 41–473
Fax: +43 50809 41–499
crawler.crane@liebherr.com
www.liebherr.com
Reeving of hoist ropesAssembly of boom
HS 895 HD – 10099249 – 03/2010 Subject to change w ithout no tice.
Loading...