LG VS840 Users manual
- 1 -
User Manual
VS840
Ver. 1.0
Nov, 2011
1
Important Customer Information
When using this product, the safety precautions below must be taken to
avoid possible legal liabilities and damages.
Retain and follow all product safety and operating instructions. Observe all
warnings in the product operating instructions. To reduce the risk of bodily
injury, electric shock, fire, and damage to the equipment, observe the
following precautions.
ELECTRICAL SAFETY
This product is intended for use when supplied with power from the
designated battery or power supply unit. Other usage may be dangerous
and will invalidate any approval given to this product.
SAFETY PRECAUTIONS FOR PROPER GROUNDING
INSTALLATION
CAUTION: Connecting to improperly grounded equipment can result in an
electric shock to your device. This product is equipped with a USB cable
for connecting to a desktop or notebook computer. Be sure your computer
is properly grounded (earthed) before connecting this product to the
computer. The power supply cord of a desktop or notebook computer has
an equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet which is properly installed and grounded
in accordance with all local codes and ordinances.
SAFETY PRECAUTIONS FOR POWER SUPPLY UNIT
Use the correct external power source
A product should be operated only from the type of power source indicated
on the electrical ratings label. If you are not sure of the type of power
source required, consult your authorized service provider or local power
company. For a product that operates from battery power or other sources,
refer to the operating instructions that are included with the product.
2
Important Customer Information
Handle battery packs carefully
This product contains a Li-ion battery. There is a risk of fire and burns if
the battery pack is handled improperly. Do not attempt to open or service
the battery pack. Do not disassemble, crush, puncture, short external
contacts or circuits, dispose of in fire or water, or expose a battery pack to
temperatures higher than 60°C (140°F).
WARNING: Danger of explosion if battery is incorrectly replaced. To
reduce risk of fire or burns, do not disassemble, crush, puncture, short
external contacts, expose to temperature above 60°C (140°F), or dispose
of in fire or water. Replace only with specified batteries. Recycle or
dispose of used batteries according to the local regulations or reference
guide supplied with your product.
Take extra precautions
●
Keep the battery or device dry and away from water or any liquid as it
may cause a short circuit.
●
Keep metal objects away so they don’t come in contact with the battery
or its connectors as it may lead to short circuit during operation.
●
The phone should be only connected to products that bear the USB-IF
logo or have completed the USB-IF compliance program.
●
Do not use a battery that appears damaged, deformed, or discolored, or
one that has any rust on its casing, overheats, or emits a foul odor.
●
Always keep the battery out of the reach of babies and small children,
to avoid swallowing of the battery. Consult a doctor immediately if the
battery is swallowed.
●
Only use the battery with a charging system that has been qualified with
the system per this standard, IEEE-Std-1725-200x. Use of an unqualified
battery or charger may present a risk of fire, explosion, leakage or other
hazard.
●
Replace the battery only with another battery that has been qualified with
the system per this standard, IEEE-Std-1725-200x. Use of an unqualified
battery may present a risk of fire, explosion, leakage or other hazard.
3
Important Customer Information
●
Avoid dropping the phone or battery. If the phone or battery is dropped,
especially on a hard surface, and the user suspects damage, take it to a
service center for inspection.
●
If the battery leaks:
Do not allow the leaking fluid to come in contact with skin or clothing. If
contact occurs, flush the affected area immediately with clean water and
seek medical advice.
Do not allow the leaking fluid to come in contact with eyes. If contact
occurs, DO NOT rub; rinse with clean water immediately and seek
medical advice.
Take extra precautions to keep a leaking battery away from fire as there
is a danger of ignition or explosion.
SAFETY PRECAUTIONS FOR DIRECT SUNLIGHT
Keep this product away from excessive moisture and extreme
temperatures. Do not leave the product or its battery inside a vehicle or in
places where the temperature may exceed 140°F (60°C), such as on a car
dashboard, window sill, or behind glass that is exposed to direct sunlight or
strong ultraviolet light for extended periods of time. This may damage the
product, overheat the battery, or pose a risk to the vehicle.
PREVENTION OF HEARING LOSS
CAUTION: Permanent hearing loss may occur if earphones or headphones
are used at high volume for prolonged periods of time.
SAFETY IN AIRCRAFT
Due to the possible interference caused by this product to an aircraft’s
navigation system and its communications network, using this device’s
phone function on board an airplane is against the law in most countries. If
you want to use this device when its use is restricted on board an aircraft,
remember to switch to Airplane Mode which turns off RF functions that
could cause interference.
4
Important Customer Information
ENVIRONMENT RESTRICTIONS
Do not use this product in gas stations, fuel depots, chemical plants or
where blasting operations are in progress, or in potentially explosive
atmospheres such as fueling areas, fuel storehouses, below deck on
boats, chemical plants, fuel or chemical transfer or storage facilities, and
areas where the air contains chemicals or particles, such as grain, dust, or
metal powders. Please be aware that sparks in such areas could cause an
explosion or fire resulting in bodily injury or even death.
EXPLOSIVE ATMOSPHERES
When in any area with a potentially explosive atmosphere or where
flammable materials exist, the product should be turned off and the user
should obey all signs and instructions. Sparks in such areas could cause an
explosion or fire resulting in bodily injury or even death. Users are advised
not to use the equipment at refueling points such as service or gas stations,
and are reminded of the need to observe restrictions on the use of radio
equipment in fuel depots, chemical plants, or where blasting operations
are in progress. Areas with a potentially explosive atmosphere are often,
but not always, clearly marked. These include fueling areas, below deck on
boats, fuel or chemical transfer or storage facilities, and areas where the air
contains chemicals or particles, such as grain, dust, or metal powders.
ROAD SAFETY
Vehicle drivers in motion are not permitted to use communication services
with handheld devices, except in the case of emergency. In some countries,
using hands-free devices as an alternative is allowed.
5
Important Customer Information
SAFETY PRECAUTIONS FOR RF EXPOSURE
●
Avoid using your phone near metal structures (for example, the steel
frame of a building).
●
Avoid using your phone near strong electromagnetic sources, such as
microwave ovens, sound speakers, TV and radio.
●
Use only original manufacturer-approved accessories, or accessories that
do not contain any metal.
●
Use of non-original manufacturer-approved accessories may violate your
local RF exposure guidelines and should be avoided.
INTERFERENCE WITH MEDICAL EQUIPMENT FUNCTIONS
This product may cause medical equipment to malfunction. The use of this
device is prohibited in most hospitals and medical clinics.
If you use any personal medical device(s), consult the manufacturer of
your device(s) to determine if the device(s) are adequately shielded from
external RF energy. Your physician may be able to assist you in obtaining
this information. Turn your phone OFF in health care facilities when any
regulations posted in these areas instruct you to do so. Hospitals or health
care facilities may be using equipment that could be sensitive to external
RF energy.
HEARING AIDS
Some digital wireless phones may interfere with some hearing aids. In the
event of such interference, you may want to consult your service provider,
or call the customer service line to discuss alternatives.
6
Important Customer Information
NON-IONIZING RADIATION
Your device has an internal antenna. This product should be operated in its
normal-use position to ensure the radiative performance and safety from
interference. As with other mobile radio transmitting equipment, users are
advised that for satisfactory operation of the equipment and for personal
safety, it is recommended that no part of the human body be allowed to
come too close to the antenna during operation of the equipment.
Use
only the supplied integral antenna. Use of unauthorized or modified antennas
may impair call quality and damage the phone, causing loss of performance
and SAR levels exceeding the recommended limits as well as result in non-
compliance with local regulatory requirements in your country.
To assure
optimal phone performance and ensure human exposure to RF energy is
within the guidelines set forth in the relevant standards, always use your
device only in its normal-use position. Contact with the antenna area may
impair call quality and cause your device to operate at a higher power level
than needed. Avoiding contact with the antenna area when the phone is IN
USE optimizes the antenna performance and the battery life.
HAC
This phone has been tested and rated for use with hearing aids for some
of the wireless technologies that it uses. However, there may be some
newer wireless technologies used in this phone that have not been tested
yet for use with hearing aids. It is important to try the different features of
this phone thoroughly and in different locations, using your hearing aid or
cochlear implant, to determine if you hear any interfering noise. Consult
your service provider or the manufacturer of this phone for information on
hearing aid compatibility. If you have questions about return or exchange
policies, consult your service provider or phone retailer.
7
Important Customer Information...........................................................1
Table of Contents ................................................................................... 7
Technical Details .....................................................................................8
The Basics ............................................................................................. 13
Connecting to Networks and Devices ............................................... 42
microSD Card ...................................................................................... 50
Calls .......................................................................................................52
Web .........................................................................................................61
Communication ....................................................................................72
Entertainment ...................................................................................... 113
Tools ..................................................................................................... 147
Settings ............................................................................................... 159
Safety ................................................................................................... 176
Specifications ..................................................................................... 199
FAQ .....................................................................................................200
LIMITED WARRANTY STATEMENT ................................................ 212
Table of Contents
8
Technical Details
Technical Details
CDMA
Standard
Designator Description
Basic Air
Interface
TIA/EIA-95A
TSB-74
ANSI J-STD-008
TIA/EIA-IS2000
CDMA Dual-Mode Air Interface
14.4kbps Radio Link Protocol and Inter-band
Operations
IS-95 Adapted for PCS Frequency Band
CDMA2000 1xRTT Air Interface
Network
TIA/EIA/IS-634
TIA/EIA/IS-651
TIA/EIA/IS-41-C
TIA/EIA/IS-124
MAS-BS
PCSC-RS
Intersystem Operations
Non-Signaling Data Communications
Service
TIA/EIA/IS-96-B
TIA/EIA/IS-637
TIA/EIA/IS-657
IS-801
TIA/EIA/IS-707-A
Speech CODEC
Short Message Service
Packet Data
Position Determination Service (gpsOne)
High Speed Packet Data
1x EV-DO
Related
Interface
TIA/EIA/IS-856
TIA/EIA/IS-878
TIA/EIA/IS-866
TIA/EIA/IS-890
CDMA2000 High Rate Packet Data Air
Interface
1x EV-DO Inter-Operability Specification for
HRPD Access Network Interfaces
Recommended Minimum Performance
Standards for HRPD High Rate Packet Data
Access Terminal
Test Application Specification (TAS) for High
Rate Packet Data Air Interface
9
Technical Details
LTE Standard Designator Description
Basic
Air Interface
TS 36.101
TS 36.104
Evolved Universal Terrestrial Radio
Access (E-UTRA);
User Equipment (UE) radio transmission
and reception
Evolved Universal Terrestrial Radio
Access (E-UTRA);
Base Station (BS) radio transmission and
reception
Conformance
Test
TS 36.521-1
TS 36.521-2
TS 36.521-3
Evolved Universal Terrestrial Radio
Access (E-UTRA);
User Equipment (UE) conformance
specification;
Radio transmission and reception;
Part 1: Conformance testing
Evolved Universal Terrestrial Radio
Access (E-UTRA);
User Equipment (UE) conformance
specification;
Radio transmission and reception;
Part 2: Implementation Conformance
Statement (ICS)
Evolved Universal Terrestrial Radio
Access (E-UTRA);
User Equipment (UE) conformance
specification;
Radio transmission and reception;
Part 3: Radio Resource Management
(RRM) conformance testing
10
Technical Details
FCC RF Exposure Information
WARNING!
Read this information before operating the phone.
In August 1996, the Federal Communications Commission (FCC) of the
United States, with its action in Report and Order FCC 96-326, adopted
an updated safety standard for human exposure to Radio Frequency (RF)
electromagnetic energy emitted by FCC regulated transmitters. Those
guidelines are consistent with the safety standard previously set by both U.S.
and international standards bodies. The design of this phone complies with
the FCC guidelines and those international standards.
Bodily Contact During Operation
This device was tested for typical use with the back of the phone kept
0.39 inches (1.0 cm) from the body. To comply with FCC RF exposure
requirements, a minimum separation distance of 0.39 inches (1.0 cm)
must be maintained between the user’s body and the back of the
phone, including the antenna. Third-party belt-clips, holsters, and similar
accessories containing metallic components should not be used. Avoid
the use of accessories that cannot maintain 0.39 inches (1.0 cm) distance
between the user’s body and the back of the phone and have not been
tested for compliance with FCC RF exposure limits.
Vehicle-Mounted External Antenna
(Optional, if available.)
To satisfy FCC RF exposure requirements, keep 8 inches (20 cm) between
the user / bystander and vehicle-mounted external antenna. For more
information about RF exposure, visit the FCC website at www.fcc.gov.
- 1 -
12
Technical Details
Part 15.105 statement
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If you experience interference with reception (e.g.,
television), determine if this equipment is causing the harmful interference by turning
the equipment off and then back on to see if the interference is affected. If necessary,
try correcting the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The phone operates on Verizon’s 4G network, based on Long Term Evolution (LTE)
technology and Mobile Broadband 4G networks in the United States*.
Now you can connect easily at high speeds to the Internet, your corporate Intranet,
and your email while you’re away from the office.
* Service not available everywhere. Visit website (verizonwireless.com/4G) for a
complete list of available areas.
* Information subject to change.
13
The Basics
Phone Overview
Front View
NOTES
All screen shots in this guide are simulated. Actual displays may vary.
Instructions to perform tasks in this guide are based on the default phone settings and
may change depending on the software version on your phone.
1. Earpiece Lets you hear callers and automated prompts.
2.
Quick Keys
- Phone Key Opens the Phone application for access to the dialpad, Call
log, Contacts list, and Groups.
-
Contacts Key Opens the Contacts application.
-
Messaging Key Opens the Messaging application.
-
Apps Key Opens the Apps screen, where you can view all of your
installed applications.
3. Menu Key Opens an Options menu with options that affect the current
screen or application. Touch and hold to access the Quick Search box.
4. Home Key Returns to the Home screen. If you’re already viewing one
of the Home screen extension canvases, it navigates you to the central
Home screen canvas. Touch and hold to view the most recently used
applications.
Proximity
Sensor
Quick Keys
- Phone Key
- Contacts Key
- Messaging Key
- Apps Key
Menu Key
Home Key
Back Key
Earpiece
Touchscreen
Search Key
Front Camera
Lens
Microphone
14
The Basics
5. Microphone Transmits your voice to the other caller and for
voice-activated functions.
6. Back Key Returns to the previous screen. Also closes pop-up display
items, such as menus, dialog boxes, and the on-screen keyboard.
7. Search Key Opens the Quick Search Box
TM
from the Home screen to
search the phone and the web.
8.
Touchscreen Displays all of the information needed to operate your
phone, such as applications, call status, date, time, signal status, and
battery strength.
9.
Front Camera Lens Use for taking pictures and recording videos of
yourself. You can also use this for video chatting. Keep it clean for
optimal performance.
10. Proximity Sensor Senses proximity towards other objects (such as your
head) so that touch commands are not accidentally activated during a call.
NOTES
●
Do not block the sensor or near the sensor to avoid problems with the touch
operations.
●
The use of a film cover produced by manufacturers other than LG can cause a
disturbance in touch operations, the display, etc.
Rear Camera
Lens
Back Cover
Speaker
Rear View
15
The Basics
11. Rear Camera Lens Use for taking pictures and recording videos. Keep
it clean for optimal performance.
12. Back Cover Encloses the battery compartment.
13. Speaker Sound comes from the rear speaker instead of the earpiece
(e.g., the speakerphone function, music player function, etc.).
14.
USB/Charger Port Allows you to connect the phone charger, USB
Cable, or other compatible accessories.
15.
3.5mm Headset Jack Allows you to plug in an optional headset for
convenient, hands-free conversations. You can also plug in headphones
to listen to music.
16.
Volume Keys Allow you to adjust the ringer, media volumes, or the in-
call volume during a call.
17.
Power/Lock Key Locks the screen with a single press. Press and hold
to open the phone Options menu for the following options: Silent mode,
Airplane mode, and Power off.
Side Views and Top View
USB/Charger
Port
Volume Keys
3.5mm
Headset Jack
Power/
Lock Key
16
The Basics
Installing the Battery and microSD Card
NOTE
It is important to fully charge the battery before initial use of the phone.
Installing the battery
The phone comes with a rechargeable battery. Keep the battery charged
while not in use in order to maximize talk, use, and standby time. The
battery charge level is shown at the top right corner of the screen.
Removing the battery
1.
Turn the phone off and use the fingertip cutout at the bottom of the phone
to remove the battery cover.
2. Use the fingertip cutout at the bottom left corner of the battery
compartment to lift the battery out.
1
Use the fingertip
cutout at the bottom
of the phone to
remove the back
cover.
2
Align the battery
contacts with the
terminals in the
battery compartment.
3
Push the battery
down until it clicks in
place.
4
Place the battery
cover over the battery
compartment, then
press it downward
until it clicks into
place.
17
The Basics
Inserting a microSD card
Turn the power off. Remove the battery cover and the
battery (as demonstrated in the previous instructions).
Locate the microSD card slot (microSD is inscribed
near the slot opening). Position the microSD card with
the label side facing up and slide it into place until it is
fully inserted and locked in place.
NOTE
The microSD card can be easily damaged by improper operation. Please be careful when
inserting, removing or handling it.
To remove the microSD card
Turn the power off. Remove the battery cover and
take the battery out. Locate the microSD card slot.
Gently pull the microSD card out to remove it.
To unmount the microSD card
It is important to unmount the card to avoid damage to the card or data
saved on the card.
1. Touch the Apps Key
.
2. Touch Settings
>Storage.
3. Touch Unmount SD card.
Memory encryption
㻌
#
Internal data for Email, Contacts, and Calendar is encoded.
㻌
#
Data cannot be encoded when the battery level is less than 50%.
㻌
#
Encoding can only be done when there is sufficient storage space
available; a minimum of 650MB of free space in the internal memory
and 500MB in the SD card is needed for encoding.
㻌
#
While encoding, you cannot access Email, Contacts, and Calendar.
Some settings will not available as well.
㻌
#
Do not connect the USB Cable while encoding.
㻌
#
Do not take out the SD card while encoding.
㻌
#
Do not take out the battery while encoding.
㻌
#
Do not press the Power button while encoding.
18
The Basics
㻌
#
After encoding, your phone will reboot to arrange the data.
㻌
#
After encoding the SD card andperforming a Factory reset without the
SD card inserted, you cannot decode the SD card.
Installing the 4G SIM card
Turn the power off. Remove the battery cover and the battery (as
demonstrated in the previous instructions). Locate the 4G SIM card slot
(a SIM card graphic is inscribed near the slot opening). Position the 4G
SIM card with the label side facing up and slide it into place until it is fully
inserted and locked in place.
Removing the 4G SIM card
Turn the power off. Remove the battery cover and
take the battery out. Locate the 4G SIM card slot.
Gently slide the 4G SIM card out to remove it.
Charging the Phone
Your phone comes with a Wall/USB Charger and a USB Cable which
connect together to charge your phone. To charge your phone:
NOTICE
Please use only an approved charging accessory to charge your LG phone.
Improper handling of the USB/Charger Port, as well as the use of an incompatible
charger, may cause damage to your phone and void the warranty.
1. Connect the USB Cable into the Wall/USB Charger. When connecting, as
shown below, the LG logo on the USB Cable should face toward you.
USB Cable
Wall/USB
Charger
19
The Basics
2. Plug the USB Cable (as shown below) into the phone’s USB/Charger Port.
Charging with USB
You can use your computer to charge your phone. To be able to charge with
the USB cable, you need to have the necessary USB drivers installed on
your PC first. Connect one end of the USB cable to the charger port on your
phone and connect the other end to a USB port on your PC. It is best to use
the rear USB port when connecting to a desktop PC. The USB hub should
be powered by an external power source.
NOTE
When you charge up the dead battery, light would be flashed on the keypad led on the
bottom of the phone. If the battery is charged enough to turn on the phone, Battery
Animation would appear on the screen and flash would stop.
Optimizing Battery Life
You can extend your battery’s life between charges by turning off features
that run in the background. You can also monitor how applications and
system resources consume battery power.
Tips to extend the life of your battery
㻌
#
Turn off radio communications that you aren’t using. If you aren’t
using Wi-Fi, Bluetooth, or GPS, use the Settings menu to turn them
off (Note that the GPS receiver is only turned on when you’re using an
application that makes use of it).
㻌
#
Turn down screen brightness and set a shorter screen timeout.
㻌
#
Turn off automatic syncing for Gmail, Calendar, Contacts, and other
applications if you don’t need it.
㻌
#
Use the Power Control widget to control the wireless connections, GPS
connection, Bluetooth power, display brightness, and syncing activity.
NOTE
Make sure the 'B' side is facing toward
you when inserting the USB Cable into
the phone.
20
The Basics
To check the battery charge level
㻌
#
Touch the Apps Key
> Settings > About phone > Battery.
㻌
The battery status (Charging or Discharging) and level (as a percentage
of fully charged) will be displayed at the top of the screen.
To monitor and control what uses the battery
The Battery use screen allows you to see which applications are consuming
the most battery power. Information on this screen allows you to identify
downloaded applications you may want to turn off when not being used, so
you can get the most out of your battery power.
㻌
#
Touch the Apps Key
> Settings > About phone > Battery >
Battery
use. This screen displays battery usage times. It lists all of
the applications or services using battery power from the greatest
amount of energy used to the least amount.
㻌
#
Touch an application or service in the Battery use screen to see the
details about its power consumption, including either how long since
last connected to a power source or how long you were last running
on battery power. Different applications or services offer different
kinds of information, and they may even include options to modify the
settings so you can reduce power consumption by that application.
Setup Wizard
The first time you turn on your phone, the Setup Wizard guides you through
signing in to your Google Account. If you don’t have one, don’t worry, the
Setup Wizard will help you create one.
NOTE
This phone supports several applications and services. It is recommended that you
purchase a data plan that meets your needs. Contact your service provider for details.
1. Press and hold the Power/Lock Key on the
top edge of your phone to turn it on.
2. Select a language and touch Next.
3. Follow the Setup Wizard to configure your phone set up including
creating or logging in to your Gmail Account.
NOTE
If you have an existing Google Account, your contacts from that account are synced to
your phone.
21
The Basics
Turning the Phone On and Off
Turning the phone on
㻌
#
Press and hold the Power/Lock Key
for a couple of seconds until
the screen turns on.
Turning the phone off
1. Press and hold the Power/Lock Key until the Phone options menu
appears.
2. Touch Power off in the pop-up menu.
3. Touch OK to confirm that you want to turn off the phone.
To unlock the phone
If you don’t use the phone for a while, the screen and
backlight will shut off to conserve battery power. To
unlock the phone:
1. Press the Power/Lock Key
. Your Lock Screen will
appear.
2. Slide the screen up to unlock it. The last screen you
were working on opens.
NOTE
This is the default Lock Screen. If you've set up an Unlock
Pattern, use your fingertip to draw the pattern.
To turn the phone sounds off
If you’re in a place where your phone sounds may disturb others, you can
quickly silence your phone from the Home screen.
1. Press the Power/Lock Key
, then unlock the screen.
2. Press and hold the Power/Lock Key
, then touch Silent mode.
OR
Press the down Volume Key
on the side of the phone until all
sounds are turned off or vibration is set.
NOTE
The Vibrate setting in the Sound menu affects this mode. If the Vibrate setting is set to
Only when not in Silent mode (or Never), then the down Volume Key turns all sounds
off. If the Vibrate setting is set to Only in Silent mode (or Always), the down Volume
Key will set the phone to vibrate.
22
The Basics
Setting Up Your Device
When you turn on your wireless device for the first time, you have the
option to quickly set up various accounts. Simply follow the on-screen
instructions to complete the initial setup of your wireless device.
To set up your device, follow the steps below:
1. Select your language and touch Next.
2. Select whether to Skip or Start the Backup Assistant application.
3. Select whether to Skip or Start the Google Account setup. With a
Google Account, Google applications are automatically synced between
your phone and computer regardless of where you make an update.
4. Select the email accounts you want to set up.
5. Read the Privacy caution and touch Next. Then set your Location
settings (Verizon Location Services/ Standalone GPS Services/
Google Location Services).
NOTE
After successfully setting up your device, you can choose to view options that teach you
about your new phone including Watch & Learn / My Verizon Mobile / Guided Tours.
These options can be viewed later by accessing the Tools section of the Apps screen.
7. Touch Done to start using the phone.
For more information on how to set up your email, visit smartphones.
verizonwireless.com/. Click on the Smartphone Support tab and select
your phone.
Getting answers about how to use phone
Touch the Apps Key > Guided tours to get information about using
phone, including the user guide and video tutorials.
23
The Basics
Setting up your Google Account
1. At the setup screen, touch Create or Sign in.
2. Enter your username and password or any other necessary information (if
creating an account).
NOTE
Touch the Back Key to close the keyboard.
3. Touch Sign in.
Now your Gmail, Google Contacts, and Google Calendar events will all be
loaded to your phone automatically.
You can use the area below to record your Google Account information for
future reference.
Username:___________________________@gmail.com
Password:________________________________________________
Your Google Account
You must sign into a Google Account to use Gmail, Google Talk, Google
Calendar, and other Google Apps; to download applications from Android
Market; to back up your settings to Google servers; and to take advantage
of other Google services on your phone.
IMPORTANT
●
If you want to restore your settings to this phone, from another phone that was
running Android release 2.0 or later, you must sign into your Google Account now,
during setup. If you wait until after setup is complete, your settings are not restored.
●
If you don’t have a Google Account, you’re prompted to create one.
●
If you have an enterprise account through your company or other organization, your IT
department may have special instructions on how to sign into that account.
●
When you sign in, your contacts, Gmail messages, Calendar events, and other
information from these applications and services on the web are synchronized with
your phone.
●
If you don’t sign into a Google Account during setup, you are prompted to sign in or to
create a Google Account the first time you start an application that requires one, such
as Gmail or Android Market.
●
When you sign in, you’re prompted to enter your username and password using the
on-screen keyboard.
24
The Basics
Phone’s Status Icons
The Status Bar appears at the top of every screen. It displays icons
indicating that you’ve received notifications (on the left) and icons indicating
the phone’s status (on the right), along with the current time.
If you have more notifications than can fit in the Status Bar, a plus icon
prompts you to open the Notifications panel to view them all.
The following icons indicate the status of your phone.
Call icons
Microphone muted during a
call
Missed call
In call In call using Bluetooth device
Speaker is on Privacy call
Calendar & Alarm icons
Calendar event notification Alarm set
Email and Messaging icons
New message received Sending message failed
High priority message
received
New Gmail message received
Google Talk message received
New Voicemail received
Sound icons
Music currently playing Silent mode is on
Vibrate mode is on Wired headset connected
Notification icons
Status icons
25
The Basics
Network icons
4G network connected
Download through 4G
network
4G network is in use Upload through 4G network
3G network connected 3G network is in use
Downloading data Uploading data
GPS is on No service
Acquiring GPS access Strong network signal
Airplane mode is on Weak network signal
Location service is on Location service is off
Connectivity icons
The following icons indicate the status of your phone.
Android debugger connected Bluetooth is on
USB connected Bluetooth device connected
No Wi-Fi signal USB tethering is on
Strong Wi-Fi signal
System icons
The following icons indicate the status of your phone.
More notifications System secure
Internal memory full System alert
SD card inserted No SD card inserted
Google sync started Error during Google sync
Battery empty Battery full
Battery charging
Battery status unknown
(error)
No SIM card Unknown SIM card
26
The Basics
Getting to Know the Home Screen
The Home screen is your starting point to access all of the features on your
phone. It displays application shortcuts, icons, widgets, and other features.
Quick Keys
The Quick Keys are located at the bottom of the Home screen and Apps screen.
: Opens the Phone application which displays the dialpad so you can
dial an unsaved number. It also provides additional tabs to access the
Call log, Contacts, and your Groups.
: Opens the Contacts application and displays your Contacts list. You can
also access the Phone application, Call log, and your Groups by touching
the tabs across the top of the screen.
: Opens the Messaging application.
: Opens the Apps screen which displays phone options and applications.
To return to the Home screen
㻌
#
Touch the Home Key
at any time, from any application.
To view other Home screen canvases
㻌
#
Slide your finger left or right across the Home screen. The Home
screen spans seven screen widths, allowing more space for icons,
widgets, shortcuts, and other items.
Status Bar
Shows device status information,
including the time, signal strength, battery
status, and notification icons.
Application Icon
Touch an icon (application, folder, etc.) to
open the application and use it.
Quick Keys
Provide easy, one-touch access to the
phone functions used most often.
Apps Key
Touch to open the Apps screen to view all
of your installed applications.
27
The Basics
Touchscreen
Your touchscreen provides an excellent way to interact with and use your
Android phone. With the touch of your finger, you can download and use
available applications, make menu selections, and access data saved to
your phone.
The following terms are used for describing the different available actions
using the touchscreen:
Touch or tap
A single finger touch selects an item. For example, touch
an icon (e.g., application or menu item), touch words (e.g., menu selection
or to answer onscreen question), or touch letters and numbers to type.
Touch and hold
Touch and hold an item on the screen by touching it
and not lifting your finger until an action occurs. For example, to open a
Context menu for customizing the Home screen, touch an empty area on
the Home screen until the Context menu appears.
Drag
Touch and hold an item for a moment and then, without lifting your
finger, move your finger on the screen until you reach the target position.
You can drag items on the Home screen to reposition them and drag the
Status Bar downward to open the Notificarions Panel.
Home Screen Canvas Indicator
The dots near the top of the screen indicate which Home screen canvas you are viewing.
TIP
Pinch in on the Home screen to display
the mini canvas view, then touch the
Home screen canvas you want to view.
28
The Basics
Swipe or slide
To Move your finger quickly across the surface of the
screen, without pausing when you first touch it (so you don’t drag an
item instead). For example, you can drag or slide the screen up or down
to scroll a list, or browse through the different Home screens by swiping
from left to right (and vice versa).
Double-tap
Double-tap to zoom a web page or a map. For example,
quickly double-tap a section of a web page to zoom that section to fit the
width of the screen. You can also double-tap to control the zoom in Maps
and in other applications.
Pinch-to-Zoom
Use your index finger and thumb in a pinch or spread
motion to zoom in or out when using the browser, a map, or pictures.
This motion can also be used to expand or compress the Applications
screen items. It also changes the Home screen to mini canvas view.
Rotate the screen
From many applications, the orientation of the screen
rotates with the phone as you turn it from upright to sideways and back again.
Auto-fit screen
The resolution size of the downloaded application would
be optimized to phone’s screen.
Text Input Methods
On-screen Keyboard
You can easily enter text using the on-screen keyboard. The on-screen
keyboard displays automatically on the screen when you need to enter text.
To manually display the keyboard, simply touch a text field where you want
to enter text.
Rotate the phone sideways for
landscape orientation.
Rotate the phone upright for portrait
orientation.
29
The Basics
Typing tips
Enter other characters
From the numbers keyboard, touch the Symbols
Key
. Touch the Numbers Key or the
Letters Key [alpha key graphic] to exit from the
symbols keyboard.
Enter one capital letter Touch the Shift Key
.
Enter all capital letters
Touch the Shift Key
twice.
Touch again to revert to lowercase.
Highlight text
Double-tap a word to highlight it. To highlight a
range of text, double-tap the screen, then drag
the blue highlight markers to highlight the text
you want.
Cut or copy selected text
Touch and hold the the highlighted text, then
touch Cut or Copy.
Paste cut or copied text
Touch and hold the location to paste the text,
then touch Paste.
Delete a character Touch the Delete Key
.
Language toggle
Touch and hold the Language Key to open a
dialog box to set the languages to toggle between.
Text input settings
To change your text entry settings and see the dictionary of terms you’ve
used, from the Home screen, touch the Apps Key
> Settings >
Language & keyboard.
●
To change the default language, touch Select language.
Toggles between
different languages.
Toggles from 123/SYM
mode to ABC mode.
Loading...