SIMPLE MANUAL
Wireless
Sound Bar
ENGLISH
FCC Compliance Statement
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference
by one or more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and
the receiver.
yConnect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
yConsult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause undesired
operation. Any changes or modications in construction
of this device which are not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement: This equipment
complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not
be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated with
minimum distance 20 cm (7.8 inches) between the
antenna and your body. Users must follow the specic
operating instructions for satisfying RF exposure
compliance.
FCC Radio Frequency Interference Requirements:
High power radars are allocated as primary users of the
5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These
radar stations can cause interference with and/or damage
this device. This device cannot be co-located with any
other transmitter.
Supplier's Declaration of Conformity
Trade Name LG
Responsible Party LG Electronics USA, Inc.
Address 1000 Sylvan Ave Englewood
Cliffs, NJ 07632
Telephone (201)266-2215
Please read this manual carefully before operating your set
and retain it for future reference.
To view the instructions of advanced features,
visit http://www.lg.com and then download Owner's Manual.
Some of the content in this manual may differ from your unit.
LG Customer Information Center
1-800-243-0000 USA, Consumer
1-888-865-3026 USA, Commercial
Register your product Online!
www.lg.com
MODEL
SL3D
www.lg.com
Copyright © 2019 LG Electronics Inc. All Rights Reserved.
1806_Rev02
SK4D.DUSAWLK(SL3D)_SIM (Sheet)_MFL70585661.indd 1,4 2019-06-03 3:59:25
Printed in China
Front Panel
The buttons are located on the rear.
··································Standby / On
·······························Selects Function
·························Adjusts Volume
Rear Panel
DC IN ·················· Connect to the AC adapter
OPTICAL IN · · · · · · · · · · · Connect to an Optical device
USB
/ ··················Connect to a USB device
Subwoofer Connection1
Place the wireless subwoofer near the sound bar and
follow steps below.
a Connect the power cord of the sound bar and
the wireless subwoofer to the outlet.
b Turn on the sound bar.
c The sound bar and wireless subwoofer will be
automatically connected. The subwoofer's
yellow green LED turns on.
Manual Subwoofer Connection
If the subwoofer does not make sound, try to
connect manually.
a Press PAIRING button on the rear of the
wireless subwoofer.
y The yellow green LED on the front of the
wireless subwoofer blinks quickly.
(If the yellow green LED does not blink, press
and hold the PAIRING button.)
b Turn on the sound bar.
c Pairing is completed.
y The yellow green LED on the front of the
wireless subwoofer turns on.
TV Connection 2
a Connect the sound bar to the TV using Optical
cable.
b Set up [External Speaker (Optical)] on your TV
setting menu.
TV
Additional Device Connection
a Connect to the external device as follows.
(Set-top Box,
Player etc.)
TV
b Set the input source by pressing F repeatedly.
Remote control
ASC/BASS BLAST/CINEMA: Selects the sound effect.
NIGHT ON/OFF: Turns down the volume at night.
WOOFER LEVEL +/-: Adjusts the volume level of
subwoofer.
AUTO POWER ON/OFF: Automatically turns on by an
input source.
Replacement of battery
Additional Information
Specication
Power
consumption
AC adapter
Dimensions
(W x H x D)
Bus Power
Supply (USB)
Amplier
(Total RMS
Output
power)
Design and specications are subject to change
without notice.
Refer to the main label.
y Model :
DA-38A25
y Manufacturer : Asian Power
Devices Inc.
y Input :
100 - 240 V ~ 50 - 60 Hz
y Output : 25 V 0 1.52 A
Approx.
890.0 mm x 53.0 mm x 85.0 mm
(35.0 inch x 2.1 inch x 3.3 inch)
Without foot
5 V 0 500 mA
300 W RMS
Keep the sound bar and the subwoofer away
from the device (ex. wireless router, microwave
oven, etc.) over 1 m (3.3 ft) to prevent wireless
interference.
1 m
(3.3 ft)
SK4D.DUSAWLK(SL3D)_SIM (Sheet)_MFL70585661.indd 5-8 2019-06-03 3:59:29