LG PPWRDB000 Instructions for quick setup

Download

MALTI

PORTUGUÊS

ENGLISH

QUICK GUIDE

AIR CONDITIONER

SLOVENČINA

SLOVENŠČINA

LATVIEŠU VALODA

LIETUVIŲ KALBA

GAEILGE

МАКЕДОНСКИ

ITALIANO

MAGYAR

БЪЛГАРСKN

ESPAÑOL

FRANÇAIS

SRPSKI

DEUTSCH

HRVATSKI

ΕΛΛΗΝΙΚΆ

SVENSKA

ČEŠTINA

NORSK

Please read this installation manual completely before installing the product. Installation work must be performed in accordance with the national wiring standards by authorized personnel only. Please retain this installation manual for future reference after reading it thoroughly.

PDI (PDI Standard) PPWRDB000 Original instructions

[

Representative] LG Electronics Inc. EU Representative : LG Electronics European Shared Service Center B.V.

[

Manufacturer] LG Electronics Inc. Changwon 2nd factory 84, Wanam-ro, Seongsan-gu, Changwon-si,

Krijgsman 1, 1186 DM Amstelveen, The Netherlands

Gyeongsangnam-do, KOREA

For more information, Refer to the CD or LG Web site (www.lg.com).

MFL69157007

Rev.00_092520

www.lg.com

NEDERLANDS

SUOMI

SHQIP

ÍSLENSKA

BOSANSKI

POLSKI

DANSK

LIMBA ROMÂNĂ

EESTI KEEL

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS (Only Australia)

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• For connections and wiring to the external control devices and the supply cord, refer to the wiring diagram in the service manual.

• For more information on the following, refer to the installation manual:

- The method of connection of the appliance to the electrical

supply and interconnection of separate components;

- dimensions of the space to be provided for the appliance;

- dimensions and position of the means for supporting and

fixing the appliance within this space;

- minimum distances between the various parts of the

appliance and the surrounding structure;

- how the appliance is to be fixed to its support.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• The appliance shall be installed in accordance with the national wiring regulation.

• Details of fuses as below:

Rating Type

Non Time Delay Fuse,

125 V / 1 A

0451001MRL CERAMIC 125V 1A UL

SMD TP LITTELFUSE INC

SAFETY PRECAUTIONS

SAFETY PRECAUTIONS (For global)

• This product must be installed by an installation professional from an LG authorized service center.

• Any issues stemming from an installation by an unauthorized person is the responsibility of the user and will not be covered by warranty.

• The following safety precautions are to prevent any unforeseen dangers or damage.

• This product has been designed for business use, or for areas outside the home, and has passed the Electromagnetic Interference Test.

WARNING

It can result in serious injury or death when the directions are ignored.

CAUTION

It can result in minor injury or product damage when the directions are ignored.

ENGLISH

WARNING

Installation

• To reinstall the product, please contact the dealer from where you purchased the product, or a service center for reinstallation service.

- Installation of the product by an unauthorized person may result in

fire, electric shock, explosion, injury, or a malfunctioning of the product.

• Do not twist or damage the power cord.

- It may cause fire or electric shock.

• For electrical work, please contact the dealer from where you purchased the product, or a service center.

- Disassembly or repair by an unauthorized person may result in fire

or electric shock.

• Install the product in an area shielded from rain.

- If water gets into the product, it may malfunction.

• Do not install the product in a humid area.

- If the product is damp, it may malfunction.

• For installation of the product, please contact the dealer from where

SAFETY PRECAUTIONS

ENGLISH

you purchased the product, or a service center.

- Installation of the product by an unauthorized person may result in fire, electric shock, explosion, injury, or a malfunctioning of the product.

• For electrical work, please have an electrician do the work based on the installation manual and specified circuit diagram.

- Using an unsuitable cord, or having a non-professional work on the

electricals may result in fire or electrical shock.

• Do not place the product near a fire source.

- It may result in the product catching fire.

• If the product is installed in a hospital or a communication base station, provide sufficient protective equipment against electrical noise.

- The product may malfunction or other products may work

abnormally.

• Securely install the product.

- If the product is not secured during installation, it may fall or

malfunction.

• Read the manual thoroughly to correctly install the product.

- If not, an incorrect installation may cause fire or electric shock.

• When wiring the product, do not use a non-standard cable, nor extend the cable excessively.

- It may cause a fire or electric shock.

• Securely install the power cord and communication cable.

- An unsecure installation may result in a fire or electric shock.

• Do not connect the power cord to the communication terminal.

- It may cause a fire, electric shock, or a product malfunction.

• Do not install the product in an area near combustible gas.

- It may result in fire, electric shock, explosion, injury, or a

malfunctioning of the product.

• Always ground the product.

- There is risk of fire or electric shock.

Use

• Do not place a heavy object on the power cord.

- It may cause a fire or electric shock.

• Do not change or extend the power cord arbitrarily.

- It may cause a fire or electric shock.

• Use the cord specific to the product.

SAFETY PRECAUTIONS

- Using an unauthorized non-standard cord may result in a fire or electric shock.

• Do not use a heat device near the power cord.

- It may cause a fire or electric shock.

• Ensure that water never gets into the product.

- It can result in an electric shock, or the product may malfunction.

• Do not place any container with liquid on the product.

- The product may malfunction.

• Do not touch the product with wet hands.

- It may cause a fire or electric shock.

• Use standard components.

- Use of an unauthorized product may result in fire, electric shock, explosion, injury, or a malfunctioning of the product.

• If the product has been submerged in water, you should contact a service center.

- It may cause a fire or electric shock.

• Do not shock the product.

- The product may malfunction.

• Do not store or use any combustible gas or flammable substances near the product.

- It may cause a fire, or a product malfunction.

• Do not disassemble, repair, or revamp the product arbitrarily.

- It may cause a fire or electric shock.

• Children and the elderly should use the product under the supervision of a guardian.

- Carelessness may cause an accident, or the product to

malfunction.

• The guardian should prevent children from accessing the product.

- The product may be damaged or it may fall, causing injury to

children.

• Keep in mind the operating temperature range specified in the manual. if there is no operating temperature range in the manual, use the product between 0 °C ~ 40 °C (32 °F ~ 104 °F).

- If the product is used outside this range, the product may be

severely damaged.

• Do not press the switch or button with a sharp object.

- It can result in an electric shock, or the product may malfunction.

• Do not wire the product while it is turned on.

- It may cause a fire or electric shock.

ENGLISH

SAFETY PRECAUTIONS

ENGLISH

• If the product sounds or smells different, stop using the product.

- It may cause a fire or electric shock.

• Do not place a heavy object on the product.

- The product may malfunction.

• Do not spray water on the product, or clean it with a water-soaked cloth.

- It may cause a fire or electric shock.

• Do not use the product for the preservation of animals and plants, precision instruments, art pieces, or for other special purposes.

- It may cause property damage.

• Dispose the packing material safely.

- The packing material may result in personal injuries.

CAUTION

Installation

• Securely install the product in an area where the weight of the product can be supported.

- The product may fall and be destroyed.

• Do not use the product where there is oil, steam, or sulfuric gas.

- It may effect the product's performance, or damage it.

• Check the rated power capacity.

- It may cause a fire, or a product malfunction.

• Use the adaptor provided with the product or power from a class 2 24 V~ transformer, depending on model.

- If a non-standard adaptor is used, the product may malfunction.

The adaptor is not provided with the PDI package sold in the U.S.

• Be careful not to drop or damage the product when moving it.

- The product may malfunction or the person may sustain an injury.

• Ensure that the cord is connected securely to prevent dew, water, or insects from getting into the product.

- If a foreign substance gets inside, it may cause an electric shock

or the product may malfunction.

Use

• Clean the product with a soft cloth, but not with a solvent-based detergent.

- The use of a solvent-based detergent may cause a fire or deform

the product.

SAFETY PRECAUTIONS

• Do not touch the panel using a pointy or sharp object.

- It can result in an electric shock, or the product may malfunction.

• Do not let the product come into contact with a metal substance.

- The product may malfunction.

• When sterilizing or disinfecting, stop using the product.

- The product may work abnormally.

• Do not touch inside the product.

- The product may malfunction.

• Check the condition of the product after using the product for an extended period of time.

- If the product is used for an extended period of time, the product's

condition may be worsen, causing injury to the user.

• Do not leave the product near a flower base, water bottle, or any other liquids.

- It may cause a fire or electric shock.

• If the liquid crystal of the product is broken, please do not let your skin such as face or hands contact with.

- Personal injury or property damage may occur.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• Appliance shall be disconnected from its power source during service and when replacing parts.

ENGLISH

According to IEC 60335-1 This appliance is not intended for use by person (including children)

with reduced physical, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

According to EN 60335-1 This appliance can be used by children aged from 8 years and above

and person with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

ENGLISH

SAFETY PRECAUTIONS

CAUTION

Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.

Disposal of your old appliance 1 When this crossed-out wheeled bin symbol is attached to a product

it means the product is covered by the European Directive 2002/96/EC.

2 All electrical and electronic products should be disposed of

separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3 The correct disposal of your old appliance will help prevent potential

negative consequences for the environment and human health.

4 For more detailed information about disposal of your old appliance,

please contact your city office, waste disposal service or the shop where you purchased the product.

COMPONENTS

ENGLISH

POWER

155 mm

PPWRDB000

WHM

SELECT

ODU

CHECK

WHM

270 mm

Power distribution indicator

POWER

WHM

ODU

CHECK

WHM

Front cover

Protection class IP20

155 mm

120 mm

Power supply

1 core

Manual

Screw

Item Specification

NAME OF EACH PART

ENGLISH

NAME OF EACH PART

ڸ Front cover

ڹ LED display

ں Menu button ڻ LCD display

ڼ SELECT button

ڹ LED display ڽ Navigation button

① Front cover ② LED display

power indicator

③ Menu button

setting and electric power

④ LCD display

and power usage

Displays current status of

Use for checking initial

Displays setting information

POWER

PPWRDB000

WHM

ODU

CHECK

WHM

SELECT

ODU

CHECK

WHM

ھ Power supply

⑤ SELECT button ⑥ Navigation button

Use for initial setting

Use for checking

initial setting and electric power

⑦ Power supply

Supply power for power

indicator

INSTALLATION METHOD

Power cable for 3 phase 4 wire Power cable for single phase Communication cable (2 wire shielded cable): Between outdoor unit and central controller Communication cable (2 wire shielded cable): Between indoor unit and outdoor unit Pulse signal wire Refrigerant pipe

INSTALLATION METHOD

Diagram of overall product conﬁguration

When interlocked to pulse type wattmeter

• Interlocked Operation with Central Controller (interlocked to EHP product)

Power In

single phase

220-240 V~,

50/60 Hz

POWER

WHM

PPWRDB000

ODU

(00) (01) (02) (03)

Power cable of indoor unit

(10) (11) (12) (13)

Pulse signal Pulse signal

SELECT

CHECK

WHM

RS-485

(LGAP)

Wattmeter

Power In 3

phase 4 wire

380-415 V 3N~,

50/60 Hz

ENGLISH

CAUTION

• Depending on the electric power, use the wattmeter for remote reading by sending the pulse signal.

• Use the wattmeter with the pulse width of 50 ms ~ 400 ms.

• The wattmeter pulse must be able to sink at least 3 mA or more of current in the power indicator.

• Use the wattmeter of 1 W/Pulse, 2 W/Pulse, 4 W/Pulse, 6 W/Pulse, 8 W/Pulse, 10 W/Pulse, 100 W/Pulse, PT/CT(1 ~ 50 000).

• When setting the wattmeter, set it to Slave Mode.

• Maximum of 2 wattmeters can be installed.

• The distance between power indicator and wattmeter should be shorter than 10 m in normal circumstance.

• When electrical or mechanical noise is expected, more shorter wiring is needed.

h EHP (Electric Heat Pump): It is an electric air conditioner to drive the compressor by electric power.

INSTALLATION METHOD

ENGLISH

• When interlocked to GHP product

- When linked with the GHP product, the central controller is linked only possible model of ACS IV series or later.

(00) (01) (02) (03)

Pulse signal(Power)

Pulse signal(Gas)

POWER

WHM

SELECT

PPWRDB000

ODU

CHECK

WHM

Wattmeter

Power In 3

phase 4 wire

380-415 V 3N~,

50/60 Hz

Gas meter

RS-485

(LGAP)

CAUTION

• Use the wattmeter for remote reading to send pulse signal depending on wattage.

• Use the wattmeter with the pulse width of 50 ms ~ 400 ms.

•

The wattmeter pulse must be able to sink at least 3 mA or more of current in the power indicator.

• Use the wattmeter for 1 W/Pulse, 2 W/Pulse, 4 W/Pulse, 6 W/Pulse, 8 W/Pulse, 10 W/Pulse, 100 W/Pulse, PT/CT(1 ~ 50 000).

• Use the gas meter for remote reading to send pulse signal depending on gas consumption.

• Use the gas meter with the pulse width of 50 ms or more.

• Use the gas meter containing the max. gas pressure of 0.2 m3/h ~ 10 m3/h.

• Gas meter pulse must be able to sink at least 3 mA of current or more in the power indicator.

• Use the gas meters for 1 ℓ/Pulse, 2 ℓ/Pulse, 4 ℓ/Pulse, 6 ℓ/Pulse, 8 ℓ/Pulse, 10 ℓ/Pulse, 100 ℓ/Pulse, VT&Pr(1 ~ 50 000).

• Set to Slave Mode when setting the wattmeter or gas meter.

• Wattmeter or gas meter can be installed up to 1.

• Connection cable for the power indicator and wattmeter (gas meter) must not exceed 10 m in normal circumstance.

• Reduce the length of connection cable if there is any electrical or mechanical noise on the site.

h GHP (Gas engine Heat Pump): It is a gas air-conditioner to drive the compressor with LNG or LPG as

a heat source and the gas engine electric power.

INSTALLATION METHOD

How to wire the product (when EHP product is connected)

ENGLISH

Wiring Power Indicator

Connection of pulse type

wattmeter (Port 1 ~ 2)

POWER

24 V~ power is supplied

for power supply device

CAUTION

WHM

SELECT

PPWRDB000

ODU

WHM

Connect to central controller 485 communication cable

CHECK

Wiring Power Supply

220-240 V~ power cable

connection

terminal

Grounding cable

connection

terminal

Fixing clamp

220-240 V~

24 V~ power cable connection terminal

24 V~

• Power must be turned on after the product is wired completely.

How to wire the product (when GHP product is connected)

Wiring Power Indicator

Connected to pulse-type wattmeter (Port 1)

Connected to pulse-type gas meter (Port 2)

Wiring Power Supply

POWER

24 V~ power is supplied for power supply device

CAUTION

PPWRDB000

WHM

SELECT

ODU

CHECK

WHM

Connect to central controller 485 communication cable

220-240 V~ power cable

connection

terminal

Grounding cable

connection

terminal

Fixing clamp

220-240 V~

24 V~

24 V~ power cable connection terminal

• Power supply must be applied after wiring the product is completed, if applicable.

INSTALLATION METHOD

POWER

WHM

PPWRDB000

ODU

SELECT

WHM

CHECK

ENGLISH

Wiring

• Separate the power supply case.

• Loosen the clamp fixating the power supply.

• Connect the 220-240 V~ power cable to the black and grounding terminal.

• Connect the 24 V~ power cable to the yellow terminal.

• Use the clamp to fixate the 220-240 V~ and 24 V~ power cable.

• Use the screw to assemble the case.

• Use the included screws to fixate the power indicator and power supply at appropriate locations within the electric panel.

• Connect the 24 V~ power cable connected to the power supply to the power terminal of the power indicator.

• Wire wattmeter, gas meter, central controlled communication cable, and the repeater for remote reading.

• Install the included core to the 24 V~ power cable.

CAUTION

Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

Power connection

POWER

WHM

SELECT

PPWRDB000

CHECK

ODU

WHM

220-240 V~

Install core

Mounting on wall

WARNING

• Always tighten the terminal screws so that they do not become loose.

• When connecting the power and communication cable, always use the terminal (O-Ring, Y-Ring).

• For 220-240 V~ power cable, use (CV) 1.5 mm 24 V~ power cable, use the CV wire.

CAUTION

• Power must be turned on after the product is wired completely.

x 3 and for

INSTALLATION METHOD

ENGLISH

Connect the wattmeter and

communication cable (EHP products)

When connecting the pulse-type wattmeter

• Independent Operation of Power Indicator (interlocked to EHP product)

Pulse type wattmeter

POWER

CAUTION

1. Please read the manual carefully, before using the product.

2. The installation requires expert skills, and it should be installed by the service or other shops specialized in the installation and recognized by our company.

3. For all the problems arising after installation by someone who has no relevant qualiﬁcations, our company will not provide free service

WHM

PPWRDB000

Pulse type wattmeter

SELECT

CHECK

ODU

WHM

Connection of wattmeter, gas meter and communication cable (GHP products)

When connecting the pulse-type wattmeter / gas meter

Pulse type wattmeter

POWER

CAUTION

1. Please read the manual carefully, before using the product.

2. The installation requires expert skills, and it should be installed by the service or other shops specialized in the installation and recognized by our company.

3. For all the problems arising after installation by someone who has no relevant qualiﬁcations, our company will not provide free service

Outdoor Unit

(Central controller)

WHM

PPWRDB000

Pulse type gas meter

SELECT

CHECK

ODU

WHM

Outdoor Unit (Central controller)

CAUTION

• The color and polarity of the signal wire may be different from the details indicated on the case depending on the manufacturer of wattmeter. [Black: (-), white: (+)]

• When connecting the 485 communication cable, make sure to check the A, B polarity.

• After connecting the wattmeter, check whether the signal is connected through the LED.

• Power indicator and Pulse Type wattmeter must be installed in same panel.

CAUTION

• The color and polarity of the signal wire may be different from the details indicated on the case depending on the manufacturer of wattmeter. [Black: (-), white: (+)]

• When connecting the 485 communication cable, make sure to check the A, B polarity.

• After connecting the wattmeter, check whether the signal is connected through the LED.

• Install the power indicator and the pulse-type wattmeter on the same panel.

• Make sure that the pulse lines of the wattmeter and gas meter are connected to the correct positions (wattmeter : port 1, gas meter : port 2)

SETTING AND USING METHOD

ENGLISH

SETTING AND USING METHOD

Setting up detailed functions (EHP products)

Flowchart for how to set up functions (EHP products)

While EHP product is selected, set the detailed functions of the power indicator with reference to the flowchart below

E L E C T R I C P O W E R

D I S T R I B U T O R

‘MENU’ button + ‘SELECT’ button

C O N N E C T I O N : M A S T E R

S T A N D B Y P : A U T O

W H M 1 : N O T U S E

W H M 2 : N O T U S E

▼ Button

C O N N E C T I O N : M A S T E R

S T A N D B Y P : A U T O

W H M 1 : N O T U S E

W H M 2 : N O T U S E

▼ Button

C O N N E C T I O N : M A S T E R

S T A N D B Y P : A U T O

W H M 1 : N O T U S E

W H M 2 : N O T U S E

▼ Button

C O N N E C T I O N : M A S T E R

S T A N D B Y P : A U T O

W H M 1 : N O T U S E

W H M 2 : N O T U S E

‘SELECT’

C O N N E C T I O N T Y P E

1 . M A S T E R

2 . S L A V E

3 . S L A V E - R C

button

S T A N D B Y P O W E R

1 . A U T O

2 . M A N U A L

* W H M W / P U L S E S E L E C T *

1 . N O T U S E

2 . 1 W / P U L S E

3 . 2 W / P U L S E

4 . 4 W / P U L S E

5 . 6 W / P U L S E

6 . 8 W / P U L S E

7 . 10 W / P U L S E

8 . 100 W / P U L S E

9 . C T / P T

SETTING AND USING METHOD

CAUTION

• Power indicator setting only can be changed during the 20 minutes after turning on the power. 20 minutes later, if you need to change settings, turn the power indicator on again.

C T & P U L S E R A T I O S E T

ENGLISH

‘SELECT’

button

‘SELECT’

button

C T : 0 0 0 0 0 , P r : 0 0 0 0 0

W H M 1 [ P u l s e / k W h ]

‘SELECT’ button

C O N S U M E U N I T S E L E C T

1 . O U T D O O R U N I T

2 . I N D O O R U N I T

‘SELECT’

button

I N D O O R A D D R E S S S E T

( S T A R T ) → ( E N D )

( 0 0 ) → ( 0 0 )

SETTING AND USING METHOD

ENGLISH

Setting detailed functions (GHP products)

Function Setting Method Flowchart (GHP products)

While GHP product is selected, set the detailed functions of the power indicator with reference to the following flowchart.

S#R#Z#H#U#)#J#D#V

G#L#V#W#U#L#E#X#W#R#U

‘MENU’ button + ‘SELECT’ button

C O N N E C T I O N : M A S T E R

S T A N D B Y P : A U T O

W H M 1 : N O T U S E

L H M 1 : N O T U S E

▼ Button

C O N N E C T I O N : M A S T E R

S T A N D B Y P : A U T O

W H M 1 : N O T U S E

L H M 2 : N O T U S E

▼ Button

C O N N E C T I O N : M A S T E R

S T A N D B Y P : A U T O

W H M 1 : N O T U S E

L H M 1 : N O T U S E

▼ Button

C O N N E C T I O N : M A S T E R

S T A N D B Y P : A U T O

W H M 1 : N O T U S E

L H M 1 : N O T U S E

‘SELECT’

C O N N E C T I O N###T Y P E

1 . M A S T E R

2 . S L A V E

3 . S L A V E - R C

button

S T A N D B Y P O W E R

1 . A U T O

2 . M A N U A L

button

* W H M W / P U L S E S E L E C T *

1 . N O T U S E

2 . 1 W / P U L S E

3 . 2 W / P U L S E

button

4 . 4 W / P U L S E

5 . 6 W / P U L S E

6 . 8 W / P U L S E

7 . 10 W / P U L S E

8 . 100 W / P U L S E

9 . C T / P T

* L H M L / P U L S E S E L E C T *

1 . N O T U S E

2 . 1 L / P U L S E

3 . 2 L / P U L S E

button

4 . 4 L / P U L S E

5 . 6 L / P U L S E

6 . 8 L / P U L S E

7 . 10 L / P U L S E

8 . 100 L / P U L S E

9 . V T & P r

SETTING AND USING METHOD

CAUTION

• Power indicator setting only can be changed during the 20 minutes after turning on the power. 20 minutes later, if you need to change settings, turn the power indicator on again.

C T & P U L S E R A T I O S E T

C T : 0 0 0 0 0 , P r : 0 0 0 0 0

W H M 1 [ P u l s e / k W h ]

‘SELECT’

button

‘SELECT’

button

C O N S U M E U N I T S E L E C T

1 . O U T D O O R U N I T

2 . I N D O O R U N I T

‘SELECT’ button

‘SELECT’

button

I N D O O R A D D R E S S S E T

( S T A R T ) → ( E N D )

( 0 0 ) → ( 0 0 )

ENGLISH

‘SELECT’

button

V T & P U L S E R A T I O S E T

V T : 0 0 0 0 0 , P r : 0 0 0 0 0

L H M 1 [ P u l s e / k L ]

‘SELECT’ button

‘SELECT’

button

I N D O O R A D D R E S S S E T

( S T A R T ) → ( E N D )

( 0 0 ) → ( 0 0 )

ENGLISH

E L E C T R I C P O W E R

D I S T R I B U T O R

C O N N E C T I O N : M A S T E R

S T A N D B Y P : A U T O

W H M 1 : 1 W , I D U , 0 0 - 0 1

W H M 2 : 1 W , O D U , 0 0 - 0 1

P O W E R & G A S

D I S T R I B U T O R

C O N N E C T I O N : M A S T E R

S T A N D B Y P : A U T O

W H M 1 : 1 W , O D U , 0 0 - 0 1

L H M 1 : 1 0 L , O D U , 0 0 - 0 1

SETTING AND USING METHOD

• If entering the setting screen for the first time.

- After turning power on, press the ‘MENU’ button and the ‘SELECT’ button at the same time and the screen will change to the screen where you can select the product connection type. Select the product type to connect, and then press the ‘SELECT’ button. Then, the selection of the product will be saved and the screen will be switched to the main standby screen.

P R O D U C T T Y P E

L G##H#O#H#F#W#U#R#Q#L#F#V

V#W#D#Q#G#D#U#G##Y##413

1 . E H P

2 . G H P

C H A N G E S E T T I N G I N F O !

• If after selecting the connection product type at least once, you are entering the setting screen.

- After turning power on, press the ‘MENU’ button and the ‘SELECT’ button at the same

time and then will be switched to the function setting screen.

• After selecting EHP product

• After selecting GHP product

• The item with letters blinking is the current setting location on the function setting screen.

h If you want to change the connection type of product

- On the function setting screen, press the (▲) button and (▼) button simultaneously, and then you can enter the connected product type setting screen.

CAUTION

• Power indicator setting only can be changed during the 20 minutes after turning on the power. 20 minutes later, if you need to change settings, turn the power indicator on again.

ver. 1.0.4

LG PPWRDB000 Instructions for quick setup

Specifications and Main Features

Frequently Asked Questions

User Manual