This lightning ash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufcient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing) instructions
in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects lled
with liquids, such as vases, should be placed on the
apparatus.
WARNING: Do not install this equipment in a
conned space such as a book case or similar unit.
CAUTION: Do not use high voltage products around
this product, (ex. Electrical swatter). This product may
malfunction due to electrical shock.
CAUTION: No naked ame sources, such as lighted
candles, should be placed on the apparatus.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings should never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
Getting Started3
CAUTION concerning the Power Cord
The Power Plug is the disconnecting device. In case
of an emergency, the Power Plug must remain readily
accessible.
Check the specication page of this owner’s manual
to be certain of the current requirements.
Do not overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords, frayed
power cords, or damaged or cracked wire insulation
are dangerous. Any of these conditions could result
in electric shock or re. Periodically examine the
cord of your device, and if its appearance indicates
damage or deterioration, unplug it, discontinue use of
the device, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention to
plugs, wall outlets, and the point where the cord exits
the device.
NOTICE: For safety marking information including
product identication and supply ratings, please refer
to the main label on the bottom or the other surface
of the product.
CAUTION when using this product in environments
of low humidity
yIt may cause static electricity in environments of
low humidity.
yIt is recommended to use this product after
touching any metal object which conducts
electricity.
1
Getting Started
1
Getting Started
Getting Started4
Symbols
~
0
1
!
Refers to alternating current (AC).
Refers to direct current (DC).
Refers to class II equipment.
Refers to stand-by.
Refers to “ON” (power).
Refers to dangerous voltage.
Table of Contents
1 Getting Started
2 Safety Information
6 Unique features
6 Introduction
7 Front
8 Rear
2 Operating
9 Charging the speaker
9 – Charging with the AC adapter
9 – Checking the charging status
10 – Checking Battery status
11 Basic Operations
11 – Using power button
11 – Bluetooth Connection
11 – Bluetooth LED status
12 – Simple Operation Guide
13 Handsfree Function
14 Voice Command
15 Mood light
16 Sound Effect
16 – Setting Sound effect
17 Listening to Music from Your External Device
18 Using BLUETOOTH® wireless technology
18 – Listening to music stored on the
BLUETOOTH devices
21 Multi phone pairing
23 Using the LG XBOOM App
23 – About “LG XBOOM” App
23 – Install “LG XBOOM” App onto Your
Bluetooth Device
24 – Activate Bluetooth with “LG XBOOM” App
25 Dual Mode Connection
27 Other Operation
27 – Resetting
27 – Turn on/off the beep sound
27 – Notice for Auto Power Off
3 Troubleshooting
28 Troubleshooting
4 Appendix
29 Trademarks and Licenses
30 Handling the Unit
31 Specifications
Table of Contents5
1
2
3
4
Getting Started6
Unique features
Auto Power Off
1
Getting Started
This unit supports to turn off by itself for saving
energy consumption. (Page 27)
AUX (Portable In)
Listen to music from your portable device.
(Smart phone, Notebook, etc.)
BLUETOOTH®
Listen to music stored on your Bluetooth device.
LG XBOOM
LG XBOOM is an app designed to let you take control
of some of LG’s latest audio devices. (Page 23-
24)
Dual Mode
You can enjoy the sound in stereo by using two
speakers. For enjoying Dual Mode, you need to
purchase another speaker.
(Available PM series model: 5, 7)
(Page 25-26)
Multi Mode
You can connect multiple speakers to enjoy the Multi
Mode sound by using only "LG XBOOM" app. For
enjoying Multi Mode, you need to purchase another
speaker.
(Available PM series model: 5, 7)
Introduction
Symbol used in this manual
Note
,
Indicates special notes and operating features.
Caution
>
Indicates cautions for preventing possible damages
from abuse.
Caution
>
Water-proof (IPX5)
This speaker is water-proof according to IPX5.
IPX5 is “Degrees of protection against ingress of
water". However, this system is not completely
water-tight. Avoid the cases below.
yDo not use unit under water or other liquid.
yWhen battery is charging, do not expose the
unit to water.
yWhen port is exposed to water, wipe off it
with a soft dry cloth. Thoroughly dry it before
using the speaker.
yPorts are not water-proof. Make sure close
the port cover securely. Refer to below image.
- Position port cover onto a and securely
press it in b.
The water resistant performance of the system is
based on our measurements under the conditions
herein described. Note that malfunctions as a
result of water immersion caused by misuse by the
customer are not covered by the warranty.
Front
Getting Started7
bcdef
a
ghijklmn
Battery LED
a
Power LED
b
Bluetooth LED
c
dts Stereo Plus LED
d
SOUND BOOST LED
e
Microphone
f
g
1
Turns On / Off: Press it.
* If the power turned on, you can check the
battery status by pressing the
2 seconds.
h j
- Adds a Bluetooth device for multi phone
pairing. (Press and hold j for 2 seconds)
- Changes to Bluetooth mode in AUX mode.
(Press j)
* When you connect the 3.5 mm stereo cable,
the function is changed to AUX mode.
- Press and hold j for 7 seconds for Bluetooth
Initialization.
button for
1
: Turn down the volume.
i P
: Turn up the volume.
j O
k N
- Plays, pauses or skips playback on the
Bluetooth mode. (Page 12)
- Receives a call on the Bluetooth device.
(Page 13)
- Mutes the sound on the AUX mode.
(
l .
- Use voice command of your smart device.
- Changes mood light.
m
- Changes sound effect. (Page 16)
n
- Changes sound effect. (Page 16)
)
(Page 14)
(Press and hold
dts Stereo Plus
SOUND BOOST
for 2 seconds) (Page 15)
1
Getting Started
1
Getting Started
Getting Started8
Rear
a
bcde f
Port cover
a
DC IN 5 V
b
USB (C type) port for charging
AUX
c
Listens to music from your portable device.
RESET button
d
e 3
Connects two speakers for Dual Mode.
(Page 25-26)
Dual Mode LED
f
Operating9
GreenOff
Charging the speaker
Charging with the AC adapter
This speaker uses built-in battery. Before using it,
charge the battery by connecting the AC Adapter.
1. Connect the supplied USB cable to the AC
adapter.
2. Connect the USB cable to DC IN 5V port of the
speaker.
3. Plug the AC power cord into an AC outlet.
(Not supplied)
Checking the charging status
When speaker's battery is charging, you can check
the charging status by Battery LED.
LEDDescription
GreenOff
Red
,
yIf you listen to the music while charging, it will
take longer to charge.
yWhen the speaker is not charging due to
overheating, The Battery LED turns on
red and amber alternately. And charging is
stopped.
yWhen the speaker’s battery is fully charged,
the Battery LED turns on green for 15
seconds and then off.
Battery is fully charged.
Battery is charging.
Note
2
Operating
Note
,
yOperating time is approx. 24 hours. It is based
on what fully charged the battery, continuous
playback using 50 % volume level and turning
off mood light and Sound Effect functions.
It may vary depending on the battery status
and operational conditions.
yIt is recommended that you use the supplied
USB cable for device protection.
Caution
>
AC adapter is not supplied. It is recommended
that you use the 5 V AC adapter approved by
LG Electronics Inc. (more than 2 A) with this
speaker because of danger of explosion. If you
do not use the recommended adapter, charging
is unavailable or charging time may differ.
Operating10
70 %
Green
70 %
10 %
Green
Amber
70 %10 %
10 %
Checking Battery status
If the power is turned on, you can check the charging
status by pressing the 1 button for 2 seconds. Then
Battery LED light will change depending on battery
charging status.
LEDDescriptionStatus
2
Operating
Battery LED turns
on green.
Green
Battery LED turns
Amber
on amber.
Battery LED
continuously
blinks in red and
Red
sounds once.
Note
,
yThe Battery LED turns on for 3 seconds, after
the 1 button press for 2 seconds.
yBattery checking status is not possible when
the speaker is charging.
yIf the speaker is connected to your
smartphone, you can check the battery
status on “LG XBOOM” app. It may vary from
actual battery capacity.
Operating 11
Basic Operations
Using power button
Power On / Off
Press the 1 button.
Bluetooth Connection
LG-PM7(XX)
Play the desired music on the Bluetooth device. After
pairing, you can control playback using the buttons
on the unit. (Page 12, 18 - 20)
Bluetooth LED status
Check the Bluetooth LED blinks before connecting
Bluetooth device.
LEDStatusDescription
Bluetooth LED
blinks with the
sound.
Bluetooth LED
turns on with the
sound.
Note
,
yIn AUX mode, Bluetooth LED turns off.
yOnce pairing is performed, it does not need to
be done again even if you turn off this unit.
yWhen switching AUX mode to Bluetooth
mode, Bluetooth LED turns on but there is
no sound.
Searching for
Bluetooth device.
Bluetooth device
is connected.
2
Operating
Operating12
Simple Operation Guide
FunctionHow to Status
Power On
Power Off
2
Operating
Bluetooth pairing
Multi phone pairing
Volume control Press P or
Play / PausePress N. -
Forward skipPress N twice.-
Backward skipPress N three times.-
HandsfreePress N. Receive and disconnect a call.
Voice CommandPress ..
Mood light
Sound effect
Dual Mode
Bluetooth Initialization
Press the
Press the
When Bluetooth LED blinks, select
LG-PM7 (XX) from device list on your
Bluetooth device.
Press and hold j for 2 seconds to add
another Bluetooth device.
Press and hold the
Press dts Stereo Plus or SOUND
BOOST.
Press the 3 button.
Press and hold j for 7 seconds.
button.Power LED turns on with the sound.
1
button. Power LED turns off with the sound.
1
.
O
for 2 seconds
Bluetooth LED turns on with the
sound.
During the search for another device,
the Bluetooth LED blinks. After pairing,
Bluetooth LED stays in white with the
sound.
When this unit reaches minimum
volume or maximum volume, you can
hear beep sound.
You can speak to operate the voice
command of your smartphone through
speaker’s microphone
When you press and hold
for 2 second, the mood light settings
will be changed.
When you press the dts Stereo Plus
or SOUND BOOST button, the sound
effect is changed..
Dual Mode LED of the Main speaker
turns on with the sound. And then Dual
Mode LED of the Other speaker turns
on with the sound.
Power and Bluetooth LED blinks
4 times.
the
button
Note
,
yIn Dual Mode, the multi phone pairing connection is not supported. (Page 25 -26)
yYou can adjust playback or volume by using your Bluetooth device.
yAfter initializing Bluetooth, it needs to reconnect with Bluetooth device. (In case of iOS devices, try to
reconnect with Bluetooth device after deleted existing connection on Bluetooth device.)
Handsfree Function
You can receive incoming call on your Bluetooth
device to this unit. Connect the unit to a Bluetooth
device.
FunctionHow to
Receive a call.Press N.
End the call.
Reject a call.
Toggle between speaker and
your phone during a call.
Press N.
Press and hold N
for 2 seconds
Press and hold N
for 2 seconds
Operating 13
Note
,
yDuring Handsfree Function, Voice Command
is not supported.
yOnly smartphone is available to use this
function.
yTo adjust the call volume, press P, O
buttons on the unit.
yIn Dual Mode, you can receive a call only on
the main speaker due to audio howling. (Page
25 -26)
yOn some Bluetooth devices, when an
incoming call is received, it might ring the
built-in ringtone, (ex. Android devices) The
Built-in ringtone is not adjustable.
yIn multi phone pairing mode, you can only
receive the call of one of the connected
devices on the speaker.
yIf a call is connected between multi paired
Bluetooth device, hands free does not work
correctly.
yEven if you switch to AUX mode while in
Bluetooth connection status, you can still
use this function.
yWhen you receive a call by using the talk
button on your phone, the call will be
connected to your phone. If you want to talk
via the speaker, It will need to be changed
to speaker mode on your phone. (Only iOS
devices)
yIf you do not want to use this function,
disable the Bluetooth setting on your phone.
Connect Bluetooth again to use this mode.
2
Operating
Operating14
Voice Command
You can speak to operate the voice command of your
smartphone through speaker’s microphone by using
the voice command app or the Siri.
Note
,
Make sure to use a smart device that has voice
command.
2
Operating
Note
,
yDuring Handsfree Function, Voice Command
is not supported.
yWhen the voice command time limit is
exceeded on smart devices, this function is
automatically canceled.
yIt is recommended that you use the Google
app (Google Assistant, Google Now etc.)
when enjoying this function on an Android
device. The Google app is provided by Google.
Some of the location feature may not be
supported by Google Policy.
yIf you want to cancel Voice command mode,
press the .button again when this function
is activating.
yFor more information, refer to voice command
app or Siri.
ySpeaking near the microphone will increase
the success rate.
yIt may not work depending on the Bluetooth
device.
1. Connect the speaker to smart device through
Bluetooth.
2. Press the .button to active voice command of
your smart device.
3. Activate voice command app as follow.
- Android O/S: Select the voice command app.
- iOS O/S: Siri activates automatically.
4. Make a request to voice command app or Siri
through microphone of speaker.
Operating 15
Mood light
You can turn on mood light on this unit.
When you press
seconds, the mood light settings will be appeared in
the order shown below.
and hold the
button for 2
2 seconds
Function
PartyVarious colors light turns on.
WaterBlue tone light turns on.
ForestYellow tone light turns on.
My style
OffMood light turns off.
Note
,
yIf you play the music, Mood light is
synchronized to the music.
yWhen you turn the speaker back on, the last
used option will be on.
Description
To enable My Style option, you
have to customize with “LG
XBOOM” app.
2
Operating
Operating16
Sound Effect
You can select a desired sound effect by using dts Stereo Plus
2
Operating
Setting Sound effect
LEDFunctionDescription
dts Stereo Plus
SOUND BOOSTYou can enjoy the powerful sound.
Standard
or SOUND BOOST
Stereo Plus delivers a wide and more ambient
soundstage with crystal-clear audio.
You can enjoy High-delity sound with balanced and
natural.
buttons.
Off / On
Note
,
yCustom EQ can customize sound effect with “LG XBOOM”.
yWhen you turn the speaker back on, the last used option will be on.
yYou can adjust sound effect using “LG XBOOM” app.
yWhen you select ”Standard” sound effect, you can enjoy premium sound with MERIDIAN technology.
yBecause ne-tune sound to provide optimal high-quality sound, there might be a little difference
between sound effect modes.
Operating 17
Listening to Music from
Your External Device
The unit can be used to listen to the music from
many types of external device.
3.5mm stereo
cable
(Not supplied)
1. Turn the power on by pressing 1 button.
2. Connect the external device to the AUX (3.5mm)
connector of the unit.
3. Turn the external device on and start playing.
Note
,
yWhen you connect the 3.5 mm stereo
cable, the function is changed to AUX mode
automatically.
yIn AUX mode, speaker limits Bluetooth
connection to prevent unintended Bluetooth
connection.
yWhen the j button is pressed during this
mode, it will switch to Bluetooth mode.
yWhen you use Dual Mode, the AUX mode is
not supported.
2
Operating
Operating18
Using BLUETOOTH®
wireless technology
About BLUETOOTH
Bluetooth is wireless communication technology for
short range connection.
The sound may be interrupted when the connection
2
interfered by the other electronic wave or you
Operating
connect the Bluetooth in the other rooms.
Connecting individual devices under Bluetooth
wireless technology does not incur any charges.
A mobile phone with Bluetooth wireless technology
can be operated via the Cascade if the connection
was made via Bluetooth wireless technology.
yAvailable Devices: Smart phone, Notebook, etc.
yVersion: 5.0
yCodec: SBC, AAC
BLUETOOTH Profiles
In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles.
This unit is compatible with following profile.
A2DP (Advanced Audio Distribution Prole)
HFP (Handsfree Prole)
AVRCP (A/V Remote Control Prole)
Listening to music stored on the
BLUETOOTH devices
Pairing your unit and BLUETOOTH
device
Before you start the pairing procedure, make sure the
Bluetooth feature is turned on in to your Bluetooth
device. Refer to your Bluetooth device’s user guide.
Once a pairing operation is performed, it does not
need to be performed again.
1. Turn on the unit then Bluetooth LED blinks with
the sound.
2. Operate the Bluetooth device and perform the
pairing operation. When searching for this unit
with the Bluetooth device, a list of the devices
found may appear in the Bluetooth device display
depending on the type of Bluetooth device. Your
unit appears as “LG-PM7 (XX)”.
Bluetooth
LG-PM7(XX)
ON
Operating 19
3. Select “LG-PM7 (XX)”.
LG-PM7(XX)
Note
,
yXX means the last two digits of
Bluetooth address. For example, if your
unit has a Bluetooth address such as
9C:02:98:4A:F7:08, you will see “LG-PM7
(08)” on your Bluetooth device.
yDepending on the Bluetooth device type,
some devices have a different pairing way. For
details about Bluetooth pairing, refer to your
Bluetooth device manual.
4. When this unit is successfully connected with
your Bluetooth device, Bluetooth LED will turn
on with the sound.
5. Listen to music.
To play a music stored on your Bluetooth device,
refer to your Bluetooth device’s user guide.
Note
,
yWhen using Bluetooth technology, you have
to make a connection between the unit and
the Bluetooth device as close as possible and
keep the distance close.
However you may experience issues in the
cases Below:
- There is an obstacle between the unit and
the Bluetooth device.
- There is a device using same frequency
with Bluetooth technology such as a
medical equipment, a microwave or a
wireless LAN device.
yIf Bluetooth connection does not work
well, go to step 1 of “Pairing your unit and
BLUETOOTH device” and try again.
yThe sound may be interrupted when the
connection has interference caused by other
electronic waves.
yDepending on the type of the device, you may
not be able to use the Bluetooth function.
yYou can enjoy Bluetooth function using
Smart phone, Notebook, etc..
yThe more distance between the unit and the
Bluetooth device, the lower the sound quality
becomes.
yBluetooth connection will be disconnected
when the unit is turned off or the Bluetooth
device gets too far from the unit.
yWhen Bluetooth connection is disconnected,
connect the Bluetooth device to the unit
again.
yBluetooth connection will be maintained
even if you change the Bluetooth function to
a different function.
yWhen you connect a Bluetooth device (iOS
device etc.) to this unit or operate the device,
the volume level will be synchronized between
each device.
yWhen the unit is not connected, Bluetooth
LED will blink.
yWhen you use the Bluetooth function, adjust
the volume to a proper level on the Bluetooth
device.
2
Operating
Operating20
Controls connected Bluetooth device
You can control connected Bluetooth device from
the unit; play, pause, skip, volume.
Note
,
yOnly Android OS and iOS is available to use
this function.
yThis function may not be supported
depending on the Bluetooth device, or
2
Operating
operated differently.
Operating 21
Multi phone pairing
The unit can be connected to 2 Bluetooth devices at
the same time.
Pairing with Two Devices
1. Connect the unit to a Bluetooth device.
(Page 18 - 20)
2. When the Bluetooth device and unit are connected, press and hold j button for 2 seconds.
2 seconds
- Then Bluetooth LED blinks with the sound. The
unit is changed to multi phone pairing mode.
3. Select "LG-PM7 (XX)" from device list on another
Bluetooth device.
LG-PM7(XX)
- Then the speaker is connection with 2 Bluetooth
devices.
4. When connection of 2 Bluetooth devices are
successful, Bluetooth LED will turn on.
2
Operating
2
Operating
Operating22
Note
,
yWhen you use Dual Mode, the multi phone
pairing connection is not supported. Press the
button to cancel Dual Mode.
3
yYou can connect this unit with up to 2
Bluetooth devices simultaneously by using
the same method as described on the previous
page. If you want to connect new Bluetooth
device with 2 Bluetooth devices connected,
press and hold j button for 2 seconds.
yWhen the speaker is in the multi phone pairing
mode, you will need to connect the other
Bluetooth device and speaker within a few
minutes (Approx. 1 minute). Otherwise multi
phone pairing mode will be canceled.
yMulti phone pairing connection may not be
supported depending on the connected device's
specications.
yRemovable/detachable Bluetooth device (Ex:
Dongle etc..) doesn't support multi phone
pairing.
yEven if this speaker is connected with up to 2
Bluetooth devices, you cannot play and control
music on both Bluetooth devices at same time.
Stop the music if you want to play the other
Bluetooth device.
yAfter multi-pairing connection, it takes a little
time for the music to be played depending on
the Bluetooth devices.
yIn case of multi phone pairing, automatically
connection of 2 Bluetooth devices is not
supported. Only one Bluetooth device will be
automatically connected to the speaker. The
other device should be connected manually.
yIf you get out of Bluetooth's effective distance
without disconnecting Bluetooth, it may take
a few minutes to connect other Bluetooth
devices. But after power off and on, you can
connect other Bluetooth devices without
waiting.
yIf you try to pair a new Bluetooth device when
it is already connected to 2 Bluetooth devices,
this speaker automatically disconnects one
Bluetooth device. (The Bluetooth device in use
is excluded from disconnection.)
yIn case of multi-pairing, only one Bluetooth
device that has control can use voice command.
Operating 23
Using the LG XBOOM
App
Note
,
It is recommended to use the latest version of
app.
About “LG XBOOM” App
“LG XBOOM” app brings a suite of new features to
this unit.
To enjoy more features, you are recommended to
download and install free “LG XBOOM” app.
Here is introduce a few of the many features of “LG
XBOOM” app.
Multi Mode: You can enjoy the Multi Mode sound by
using multiple speakers. For enjoying Multi Mode, you
need to purchase another speaker.
Install “LG XBOOM” App onto
Your Bluetooth Device
There are two ways to install “LG XBOOM” App onto
Your Bluetooth Device.
Install “LG XBOOM” App through QR
code
1. Install “LG XBOOM” app through QR code. Use
the scanning software to scan the QR code.
<Android><iOS>
2. Tap an icon for installation.
Note
,
yMake sure that your Bluetooth device is
connected to the Internet.
yMake sure that your Bluetooth device
has a scanning software application. If you
don’t have one, download one from “Google
Android Market (Google Play Store)” or
“Apple App Store”.
yDepending on the area, QR code may not
work.
2
Operating
The function is used and controlled by only "LG
XBOOM" app.
Operating24
Install “LG XBOOM” App through
“Google Android Market (Google Play
Store)” or “Apple App Store”
1. Tap the “Google Android Market (Google Play
Store)” or “Apple App Store” icon.
2. In the search bar, type in the “LG XBOOM” and
search it.
3. In the search result list, find and tap “LG XBOOM”
2
Operating
to start downloading Bluetooth app.
Note
,
yMake sure that your Bluetooth device is
connected to the Internet.
yMake sure that your Bluetooth device is
equipped with “Google Android Market
(Google Play Store)” or “Apple App Store”.
Activate Bluetooth with “LG
XBOOM” App
“LG XBOOM” app helps to connect your Bluetooth
device to this unit.
Tap “LG XBOOM” app icon on the home screen to
open “LG XBOOM” app, and go to the main menu.
Note
,
y“LG XBOOM” app will be available in the
software version as follow;
- Android O/S: Ver 5.0 (or later)
- iOS O/S: iOS10 (or later)
yDepending on the Bluetooth device, “LG
XBOOM” app may not work.
yAfter connection of “LG XBOOM” app, music
may be output from your Bluetooth device.
In this case, try connecting procedure again.
yIf you operate the other applications or
change the settings on your Bluetooth
device while using “LG XBOOM” app, “LG
XBOOM” app may operate abnormally.
yWhen “LG XBOOM” app operates abnormally,
check your Bluetooth device and the
connection of “LG XBOOM” app and then try
to connect again.
yDepending on the smart phone's operating
system, you have some differences for “LG
XBOOM” operation.
yCheck Bluetooth setting on your Bluetooth
device if “LG XBOOM” app connection does
not work well.
Operating 25
Dual Mode Connection
You can enjoy the sound in stereo by using two
speakers. For enjoying Dual Mode, you need to
purchase another speaker.
1. Press the each speaker’s 3 button.
Then the speakers are ready to Dual Mode.
2. If two speakers are successfully connected,
blinking Dual Mode LEDs will stay white. First hear
beep sound at main speaker, and then at other
speaker.
- speaker: Main speaker is to set L (left)
channel and turns on Dual Mode LED and
Bluetooth LED.
-
speaker: Other speaker is set to R (Right)
channel and turns on Dual Mode LED.
Bluetooth LED turns off.
Note
,
yIt takes up to 1 minute to connect to Dual
Mode.
yUsing Dual Mode is limited to PM 5, 7 series
model.
- When connect to PM7 and PM5 with
Dual Mode because output powers are
different, the sound will be twin.
yIf you are not connected to Bluetooth device,
main speaker's Bluetooth LED blinks.
yThe
speaker depends on MAC address of
Bluetooth.
2
Operating
PM7
Or
- Beep sound is heard and Dual Mode LED will
blink white fast.
PM5
3. Play the desired music on the Bluetooth device.
2
Operating
Operating26
Note
,
yWhen you enjoy Dual Mode, Multi phone pairing
is not supported.
- Main speaker (
Bluetooth device.
yIn Dual Mode, you can connect only the main
speaker (
yIf you turn the power off and then on again, two
speakers need to be reconnection for using Dual
Mode.
yIf the units fail to connect Dual Mode, go to step
1 and try again.
yWhen Dual Mode connection is being processed,
you cannot search the units on other Bluetooth
devices.
yWhen you disconnect Dual Mode connection,
press the 3 button of one of the two speakers
again.
yWhen you enjoy Dual Mode, you can adjust the
Volume, Playback, Sound Effect or Mood light of
both main (
same time.
yWhen you connect Dual Mode connection while
using AUX mode, this speaker automatically
changes to Bluetooth mode.
yIn Dual Mode, you can receive a call on only main
speaker preventing audio howling.
yIf you connect 3.5 mm stereo cable in Dual Mode,
it will cancel Dual Mode and then change to AUX
mode.
) connects only one
) the Bluetooth device.
) and other ( ) speakers at the
yYou can connect to Dual Mode connection with
“LG XBOOM" app. In this case, the speaker that
is connected to “LG XBOOM” app will be the
main speaker. You are only able to connect to one
speaker when connected to Dual Mode with “LG
XBOOM" app.
yTo change the Bluetooth device in Dual Mode,
press and hold j for 2 seconds to disconnect
current Bluetooth device and connect to the
desired Bluetooth device.
yWhen you connect a Bluetooth device (iOS
device etc.) to this unit or operate the device,
the volume level can be synchronized between
each device.
yIn Dual Mode, make the distance between the
speakers as close as possible between each
other.
yDepending on network environment, the Dual
Mode may not work well.
yIn Dual Mode, you can only use voice command
on the main speaker.
ySome mobile phones might not play music
properly when you try to connect Dual Mode
during playback.
yThe speaker might not synchronize audio with
video (ex. TV etc).
yPress “
yWhen you want to use the Multi mode by “LG
” button or “3” button to cancel Dual
1
Mode.
XBOOM” app., disable Dual mode and start Multi
mode connection.
Operating 27
Other Operation
Resetting
If have a malfunction with the speaker, press the
RESET button using an object like a thin pin. Then
speaker turns off. Press 1 button to try turning on
speaker again.
Turn on/off the beep sound
Set up the beep sound through "LG XBOOM" app:
"LG XBOOM" menu [ [Setting] [ [Beep Sound]
Notice for Auto Power Off
When the unit is in Bluetooth mode without music
playback for 15 minutes or in AUX mode without
button operation for 6 hours, this unit is turned off
automatically.
The function can be turned on or off.
When setting is changed in the order as below, Power
LED blinks 5 times with beep sound.
FunctionHow to
,
ON
OFF
yYou can toggle this function on and off
through “LG XBOOM” app.
yIf this function is turned off, the speaker may
appear to be off. Please press the "
to turn the unit off or the battery will be
completely discharged.
Press and hold
for 2 seconds simultaneously.
Press and hold
for 2 seconds simultaneously.
Note
,
1
1
O
,
P
" Button
1
2
Operating
Troubleshooting28
Troubleshooting
ProblemCause & Correction
No Power.
No sound or sound
distortion.
3
Troubleshooting
Bluetooth pairing does
not work well.
The unit does not
operate normally.
yThe battery is discharged. Recharge the battery.
yConnect the unit to the power supply with the AC adapter.
yThe unit or your smart device’s volume is set to minimum. Check and adjust the
volume of the unit or Bluetooth device’s volume.
yWhen you use an external device at high volume, the sound quality may be
deteriorated. Lower the volume of the devices.
yIf you use the unit for purposes other than listening to music, the sound quality
may be lowered or the unit may not work properly.
ySwitch Bluetooth off and on again on your Bluetooth device, then try pairing
again.
yBe sure your Bluetooth device is on.
yRemove the obstacle in the path of the Bluetooth device and the unit.
yDepending on the type of the Bluetooth device or surrounding environment,
your device may not be paired with the unit.
yIf the battery was fully discharged, the stored Bluetooth information can be
deleted. Previous setting may not be saved when the unit’s power is shut off.
yIn case of malfunction, please use the unit in proper place where the
temperature or humidity is not so high or low.
yIn case of overload, power and Bluetooth LEDs blink white. Please turn the
power off and then on again.
Above solutions do not
work.
yPress the RESET button on speaker using an object like a thin pin. (Page 27)
Trademarks and
Licenses
The Bluetooth® word mark and logos are
registered trademarks owned by the Bluetooth
SIG, Inc. and any use of such marks by LG
Electronics is under license.
Other trademarks and trade names are those of
their respective owners.
“Made for iPhone,” and “Made for iPod” mean
that an electronic accessory has been designed to
connect specically to iPhone or iPod, respectively,
and has been certied by the developer to meet
Apple performance standards. Apple is not
responsible for the operation of this device or its
compliance with safety and regulatory standards.
Please note that the use of this accessory with
iPhone or iPod may affect wireless performance.
Compatible iPhone/iPod
yThe unit supports the models as follows ;
- iPhone XS Max
- iPhone XS
- iPhone XR
- iPhone X
- iPhone 8 Plus
- iPhone 8
- iPhone 7 Plus
- iPhone 7
- iPhone SE
- iPhone 6s Plus
- iPhone 6s
- iPhone 6 Plus
- iPhone 6
- iPhone 5s
- iPod touch (6th generation)
The system is compatible with the latest iOS.
Depending on your iPhone/iPod software version, you
may not control your iPhone/iPod from the unit.
4
Appendix
Appendix30
Handling the Unit
When shipping the unit
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally
packed at the factory.
Keeping the exterior surfaces clean
yDo not use volatile liquids such as insecticide spray
near the unit.
yWiping with strong pressure may damage the
surface.
yDo not leave rubber or plastic products in contact
with the unit for a long period of time.
Cleaning the unit
4
To clean the player, use a soft, dry cloth. If the
Appendix
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not use
strong solvents such as alcohol, benzine, or thinner,
as these might damage the surface of the unit.
Specifications
General
Power requirements
Power consumptionRefer to the main label.
Dimensions (W x H x D)Approx. 333 mm X 127 mm X 163 mm
Operating temperature5 °C to 35 °C
Operating humidity5 % to 60 % RH
Water-proofIPX5
Inputs
AUX (Portable In)0.5 Vrms (3.5 mm stereo jack)
Battery
Battery capacity3900 mAh
Operating time
Charging time
5 V 0 2 A (AC adapter)
Built-in rechargeable battery
Approx. 24 hours.
It may vary depending on the battery status and operational conditions.
Less than 5 hours (with AC Adapter).
It can be varied depending on the conditions of the battery or operation.
Appendix 31
4
Appendix
yDesign and specications are subject to change without notice.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.