LG HFB300 Users manual

BLUETOOTH S P E AK E R P H O NE HF B- 3 0 0

User's Manual

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS :

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION

IMPORTANT NOTE :

TO COMPLY WITH THE FCC RF EXPOSURE COMPLIANCE REQUIREMENTS, NO CHANGE
TO THE ANTENNA OR THE DEVICE IS PERMITTED. ANY CHANGE TO THE ANTENNA OR
THE DEVICE COULD RESULT IN THE DEVICE EXCEEDING THE RF EXPOSURE
REQUIREMENTS AND VOID USER'S AUTHORITY TO OPERATE THE DEVICE.

Introduction

LG Speaker Phone HFB-300 can be linked to any device with Bluetooth wireless
technology that supports the Hands free & headset profile. This product can be used as a
Hands free in a car, a conference call, and a speaker phone at home or office.

Included package

Bluetooth Speaker Phone

User's Manual

Additional Information

VPC (Vehicle Power Charger)

Holster case

Part description

Front

Back

Configuration

Car

Fit the HFB-300 in the Holster case, and fix the sun visor clip into the fixing groove of the
Holster case. Then, place the HFB-300 on the sun visor toward the driver's side.
User can use the HFB-300 as a hands free.

Home or Office

User can use HFB-300 as a conference call, and also as a speaker phone.

Start

After you open the box package, please make sure the HFB-300 be fully charged before
use.

1. Open the Power Connector Outlet cover.

2. Connect the supplied charger to Power Connector Outlet f HFB-300.

●When charger plugged, the LED light of HFB-300 is RED color.

●When being fully charged, the LED light of HFB-300 is changed to GREEN

color.(It may take 3 hours to charge HFB-300 fully.)

Tip

The low battery will be alarmed by a beep sound in every 30 seconds.
Immediate charging will be required right after the low battery alarm.

Power on
Press and hold Call/Power Button for more than 2 seconds, when HFB-300 is turned
off.

●When you hear a consecutively raised sound, the power of HFB-300 is turned on.

Power off
Press and hold Call/Power Button for more than 3 seconds, when HFB-300 is turned
on.

●When you hear a consecutively lowered sound, the power of HFB-300
is turned off.

How to use

Bluetooth Pairing

1. After being turned on HFB-300, press and hold Function button for more than 3
seconds.

●After melody, the blue LED will flicker once a second.

2. With the Bluetooth enabled handset, search for HFB-300 and then register it.

●Please refer to the user manual of the handset.

●When asked for PIN code during the procedure, enter "0000" as the password.

●When the pairing procedure is done, you can hear a beep sound and see flicking blue

LED every 4~5 seconds.

●If the LED flickers once a second, user have to try again for pairing from the beginning.0

Adding Multiple handset

●HFB-300 stores up to 3 different handsets in memory.

●In case of adding a 4th handset, the oldest unused registration will be automatically

removed.

●When you want to change the priority, try to connect manually from the handset.

●If the latest paired handset supports Hands free profile, handset will automatically

connect with HFB-300.

Tip

Once HFB-300 is registered to HFB-300, it will be stayed in
paired status until deleted.

Answering a call

When handset is an incoming call, a melody will come out of HFB-300 and the blue LED
will flicker rapidly 4 times.

Press Call/Power Button while the handset is ringing.

●HFB-300 is available to start conversation.

Last number / Voice dialing
To make last number call, press Call/Power Button shortly (with beep sound once).

●In some cases of Bluetooth enabled handset, user need to press Call/Power Button twice.

To activate Voice dialing, press and hold Call/Power Button little bit longer (with two
beep sounds in a row).

●It's possible to use this function only when the user's handset supports.

Ending a call
To finish calling, press Call/Power Button.

Call Waiting
To receive a second call while answering the first call, press and hold Call/Power
Button for more than 2 seconds.

To get back to the first call, just press and hold Call/Power Button again.
Speaker Volume Control

Press Volume (+) Button to increase the speaker sound, and press Volume (-)
Button to decrease.

●The volume level runs from 1 to 8.

Microphone Volume Control
Press Function with Volume (+) Button simultaneously to increase the Microphone
volume, and press Function
Volume (-) Button longer at the same time to decrease the Microphone volume.

●The volume level runs from 1 to 4.

●Whenever changing Microphone volume level, user can hear serial sound according to

the level of the volume.
(ex. Level 1 : sound once, Level 2 : sound twice, and so on.)

Mute Function for Microphone
To make mute Microphone during an active call, press Function Button shortly.
When Function Button pressed again, Mute function is just cancelled.

Transferring Audio
Handset =>HFB-300
When user want to transfer Audio from handset to HFB-300 while calling, press