LG HF80JS User manual

Owner's Manual

LG CineBeam Laser
DLP Projector
Please read the safety information carefully before using this product.
HF80JS
P/NO : SAC37034669 (1807-REV03)
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
www.lg.com

LICENSES

Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
ENGLISH
• Image shown may differ from your projector.
• Your projector’s OSD (On Screen Display) may differ slightly from that
shown in this manual.
Manufactured under license from Dolby Laboratories. Dolby, Dolby Vision, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Denition
Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
For DTS patents, see http://patents.dts. com. Manufactured under license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, & DTS or DTS-HD and the Symbol together are registered trademarks of DTS, Inc. © DTS, Inc. All Rights Reserved.

SAFETY PRECAUTIONS

Please take note of the safety instructions to prevent any potential accident or misuse of the projector.
• Safety precautions are given in two forms, i.e., WARNING and CAUTION as
detailed below.
WARNING Failure to follow the instructions may cause serious injury and
even death.
CAUTION Failure to follow the instructions may cause personal injury or
product damage.
• Read the owner's manual carefully and keep it on hand.
ENGLISH
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning ash with
arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure
that may be of sufcient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within
an equilateral triangle is
intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Indoor Installation
WARNING
• Do not use the projector outside
and do not expose the product to any humidity or water.
- Since the product is not waterproof, this may result in a
re or electric shock.
• Do not place the projector in direct
sunlight or near heat sources such as radiators, fires, stoves, etc.
- This may result in re.
• Do not place flammable materials
such as aerosols near the projector.
- This may result in re.
• Do not allow children to cling to or
climb up to the projector.
- This may cause the projector to fall, causing injury or death.
• Do not install the product in a
ENGLISH
place with no ventilation (e.g., on a bookshelf or in a closet) or on a carpet or cushion.
- This may result in re due to the increase in internal temperature.
• Do not place the product close to
sources of steam, oil or oil mist, such as humidifiers and kitchen counters.
- Failure to do so may result in
re, electric shock, or corrosion.
• Do not install the product onto
a wall or ceiling that is close to sources of oil or oil mist.
- The product may be damaged and fall, resulting in serious injury.
• Do not place the projector where it
might be exposed to dust.
- This may result in re.
• Do not use the projector in a damp
place such as a bathroom where it is likely to get wet.
- This may result in re or electric shock.
• Do not allow a tablecloth or curtain
to block the air vent.
- This may result in re due to the increase in the internal temperature.
• Ensure good ventilation around the
projector. The distance between the projector and the wall should be at least 30 cm.
- This will prevent re due to the increase in the internal temperature.
• When installing the product on a
ceiling, a professional technician should install it using authorized tools. If installed improperly, the product may fall.
- This may cause personal injury or property damage. For installation of the product, please contact the customer support center.
• If you use a ceiling mounting device,
adhesive to prevent loosening of screws, or if you apply oil or lubricant to the product, this may cause the case to crack and the product to fall. This may also cause serious personal injury to the person below the device (if any) and damage to the product as well.
CAUTION
• When placing the projector on a
table or shelf, be careful not to put it near the edge.
- The projector could fall due to balance problems, which may cause personal injury or damage to the product. Make sure to use the projector cabinet or stand
that ts the projector.
• When moving the projector, make
sure to switch it off and remove the power plug and cords.
- The power cord may be
damaged, resulting in re or
electric shock.
• Do not place the projector on an
unstable or vibrating surface such as a wobbly shelf or a slope.
- It may fall and cause injury.
• Be careful not to tip the projector
over when connecting external devices to the projector.
- This may cause personal injury or damage to the projector.
Power
WARNING
• DISCONNECTING THE DEVICE
FROM THE MAIN POWER
- The Power plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible.
• The grounding wire should be
connected. (Except for devices which are not grounded.)
- Ensure that you connect the grounding cable to avoid electric shock. If it is not possible to
ground the unit, have a qualied
electrician install a separate circuit breaker. Do not try to ground the projector by connecting it to telephone wires, lightning rods or gas pipes.
• The power plug should be inserted
fully into the power outlet.
- An unstable connection may
cause a re.
• Do not place heavy objects on the
power cord.
- This may result in re or electric shock.
• Never touch the power plug with
wet hands.
- This may result in electric shock.
ENGLISH
• Do not plug too many devices into
one multi-power outlet.
- This may result in re due to the power outlet overheating.
• Keep the AC adapter, power plug,
ENGLISH
and the used power outlet clean from dust or foreign materials building up.
- This may result in re.
• If there is any smoke or a burning
smell from the projector or AC adapter, stop using the product immediately. Disconnect the power cord from the power outlet, and then contact the customer service center.
- This may result in re.
• To turn off the main power, remove
the power plug, which should be positioned so it is easy to access for operation.
CAUTION
• Always grab the plug to remove the
AC adapter or power cord.
- Otherwise, this may result in a
re or may damage the product.
• Refrain from constantly bending the
power cord of the AC adapter.
- If the power cord is bent excessively for a long period of time, the cord may break
inside. This may result in a re or
electric shock.
• Ensure the power cord and plug are
not damaged, modified, severely bent, twisted, pulled, sandwiched or hot. Do not use the product if the power outlet is loose.
- This may result in re or electric shock.
• Keep the power cord away from
heating devices.
- The wire’s sheath may melt,
which may result in re or
electric shock.
• Place the projector where people
will not trip over or step on the power cord to protect the power cord and plug from any damage.
- This may result in re or electric shock.
• Do not turn the projector on or
off by plugging in the power plug or unplugging it from the power outlet. (Do not use the power plug as a switch.)
- This may result in electric shock or damage to the product.
• Do not insert a conductor into the
other side of the wall outlet while the power plug is inserted into the wall outlet. In addition, do not touch the power plug immediately after it is disconnected from the wall outlet.
- This may result in electric shock.
• Only use the official power cord
provided by LG Electronics. Do not use other power cords.
- This may result in re or electric shock.
• If any water or foreign materials
have gone into the AC adapter, power cord, or the interior of the projector, turn off the projector by pressing the power button. Remove all the cables, and then contact the customer service center.
- This may result in re or electric shock.
• The surface of the AC adapter is
hot. Keep the AC adapter out of the reach of children and avoid touching it during use.
• Never disassemble the power
supply devices (AC adapter/power cord, etc.).
- This may damage the power
cord and result in a re or
electric shock.
• Connect the AC adapter and the
power cord firmly.
- Not doing so may result in a
product failure or re.
• Do not place heavy objects or put
pressure on the power cord and AC adapter and avoid damage.
- This may result in a re or may damage the product.
• Always use the AC adapter provided
or any AC adapters approved and certified by LG Electronics.
- Any other AC adapter connected may result in the
screen ickering.
ENGLISH
When in Use
WARNING
• Do not place anything containing
ENGLISH
liquid on top of the projector such as a vase, flower pot, cup, cosmetics, medicine, or ornaments, candles, etc.
- This may result in re or electric shock, or cause injury due to falling.
• In the event that there is a heavy
impact or the cabinet is damaged, switch it off, unplug it from the power outlet and contact an authorized service center.
- This may result in electric shock.
• Do not insert pieces of metal such
as coins, hairpins or metal debris, nor flammable materials such as paper or matches into the projector.
- This is to prevent electric shock
or re.
• Make sure that a child does not
swallow the batteries when you replace the old batteries in the remote control with new ones. Keep batteries out of reach of children.
- If a child swallows a battery, consult a doctor immediately.
• Never open any cover on the
projector.
- There is a high risk of electric shock.
• Do not look directly into the lens
when the projector is in use.
- The bright light may damage your eyes.
• When the lamp is on or has just
been turned off, avoid touching the air vent or lamp, because these will be very hot.
• If there is a gas leak in the room
with the projector, do not touch the projector or power outlet. Open the windows for ventilation.
- Sparks may cause re or burns.
• Unplug the power cord from the
outlet during a lightning storm.
- This will prevent shock or damage to the projector.
• Do not use the projector near
electronic devices that generate a strong magnetic field.
• Keep the plastic film used for
packaging the projector out of the reach of children.
- If not handled safely, it can cause suffocation.
• Do not keep your hand on the
projector for a long time when it is running.
• When you play a game by
connecting a game console to a projector, it is recommended that you maintain a distance of more than four times the diagonal length of the screen.
- Make sure that the connecting cable is long enough. Otherwise, the product may fall causing personal injury or damage to the product.
• Do not place the projector or its
remote control with batteries in an extremely high temperature environment.
- This may result in re.
CAUTION
• Do not place heavy objects on the
projector.
- It may fall down and cause personal injury.
• Be careful not to allow any impact
to the lens during transport.
• Do not touch the lens of the
projector.
- The lens may be damaged.
• Do not use any sharp tools on
the projector such as a knife or hammer, because this may damage the casing.
• In the event that no image appears
on the screen or no sound is heard, stop using the projector. Switch off the projector, unplug it from the power outlet and contact our service center.
- This may result in re or electric shock.
• Do not drop anything onto the
projector or allow anything to bang into the projector.
- This may cause damage to the projector or personal injury.
• It is recommended that you
maintain a distance of more than 5 to 7 times the diagonal length of the screen.
- If you watch the screen at a close distance for a long time, your eye sight may become worse.
• Do not block the light beam emitted
from the projector using a book or other object.
- Lengthy exposure to the projector beam may result in
re. In addition, the lens may
be overheated and damaged by
the reected heat. Disable the
AV function to stop projection temporarily or turn off the power.
• Do not start the projector with the
volume turned up high.
- High volume may damage hearing.
• Do not use high voltage electrical
equipment near the projector, (e.g., a bug zapper). This may result in product malfunction.
ENGLISH
10
Cleaning
WARNING
• Do not spray the projector with
ENGLISH
water when cleaning. Make sure water does not flow into the projector.
- This may result in re or electric shock.
• When there is smoke or a strange
smell coming out from the projector or a foreign object falls into the projector, please switch it off and unplug it from the power outlet and contact our service center.
- Otherwise, this may result in re or electric shock.
• Use air spray, a soft cloth or a
cotton swab moistened with a lens cleaning chemical or alcohol to remove dust or stains on the front projection lens.
CAUTION
• Contact your seller or our service
center once a year to clean the internal parts of the projector.
- If you do not clean the projector for a long period of time, dust will accumulate, which may
result in re or damage to the
projector.
• When cleaning plastic parts such
as the projector case, unplug the power first and wipe with a soft cloth. Do not spray with water or wipe with a wet cloth. Never use glass cleaner, automobile or industrial polish, abrasives, wax, benzene, or alcohol as these can damage the projector.
- This can result in re, electric shock or cause damage to the product (deformation and corrosion).
• Do not wipe the optical system
(lens, mirror) right after the product has been turned off or while the product is being operated. When cleaning each part of the product, remove the power cord and wipe gently with a soft cloth. Do not spray with water or wipe with a wet cloth. Do not use detergents, automobile or industrial polish, abrasive substances, wax, benzene, alcohol, water, etc. on the product’s main unit or optical system (lens, mirror) as this may damage the product.
- This can result in re, electric shock or cause damage to the product (deformation and corrosion).
• Remove the plug from the outlet
before cleaning the product.
- Otherwise, this may result in electric shock.
11
Laser
WARNING
• This product contains a laser
module. Do not disassemble or modify the product as this could be dangerous.
• You risk being exposed to laser
radiation if you manipulate or alter the product in a way not specified in the user manual.
• To protect your eyes avoid looking
directly into the bright light from the unit.
• Use of controls or adjustments
or performance of procedures other than those specified herein may result in hazardous radiation exposure.
CAUTION
• This product is a class 1 laser device
that meets IEC 60825-1.
Built-in laser standard (class 4 laser module)
• Wavelength: 448 nm - 462 nm
• Light output: approx. 4.35 W x 8
Product Laser Class Label
CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT CLASSE 1 PRODUIT LASER KELAS 1 PRODUK LASER URZĄDZENIA LASEROWE KLASY 1
The laser class label of product is attached to the bottom of the product.
ENGLISH
12
Others
WARNING
• When you go out, place the
ENGLISH
projector out of reach of animals, and remove the power plug from the wall outlet.
- Using a damaged power cord
may result in short circuit or re.
• Do not use the projector near high-
precision electronic devices or those that transmit weak radio signal.
- This may affect the operation of the product, causing an accident.
• Only a qualified technician can
disassemble or modify the projector. For diagnosis, adjustment, or repair, contact your seller or our service center.
- This may result in re or electric shock.
• Proper ventilation required, do not
block airflow around unit. Doing so can cause injury and internal overheating.
• Do not touch the lens; doing so can
result in burns or damage to lens. Lens and unit may be HOT during and immediately after use. Use caution when handling unit, allowing for proper cool down.
• Only use a grounded electrical
outlet. (Except for devices which are not grounded.)
• Do not insert anything into or cover
up the exhaust vents.
- This may result in re or electric shock.
• Follow all maintenance guidelines
for optimal use; service only at an authorized service center.
• Keep the batteries and remote out
of reach of children.
- This will prevent personal injury or damage to the product.
13
CAUTION
• Do not use or store the projector
outdoors for long periods of time.
• Do not mix new batteries with old
ones.
- Burst or leaking batteries may result in damage or injury.
• Be sure to unplug if the projector is
not to be used for a long period.
- Accumulated dust may result
in re or electric shock due to
overheating, ignition, or poor insulation.
• Only use the specified type of
battery.
- Burst or leaking batteries may result in damage or injury.
• Make sure you use the same type
of battery when replacing.
- In the case of a battery contact failure, the battery may drain quickly or the remote control may not work properly.
• Dispose of used batteries properly.
- This may result in explosion
or re. The correct method of
disposal may vary depending on your country or region. Dispose of the battery pack as instructed.
• Do not throw or disassemble the
battery.
- This may result in re or explosion due to damage to the battery.
• Store batteries away from metallic
objects, such as keys and paper clips.
- Excess current may cause a rapid increase in temperature,
resulting in re or burns.
• Do not store the batteries near any
heat source, such as a heater.
- This may result in re or damage to the product.
• Do not store batteries at
temperatures higher than 60 °C or in high humidity.
- This may result in explosion
or re.
• Make sure that the battery is
installed correctly.
- This prevent explosion or re.
• Incorrect battery replacement may
cause fire.
• Batteries: Store the accessories
(battery, etc.) in a safe location out of the reach of children.
Risk Group 2
CAUTION Possibly hazardous optical radiation
emitted from this product. Do not stare at operating lamp. May be harmful to the eye.
This label is attached to the bottom of the product and language may differ.
ENGLISH
14
CONTENTS
LICENSES 2
ENGLISH
SAFETY PRECAUTIONS 3
PREPARATION 15
Accessories 15
Optional Extras 16
Parts and Components 17
- Main Unit 17
- Back 18
Using the Joystick Button 19
- Basic functions 19
- Adjusting the menu 20
Projector Status Indicators 20
Installation 21
- Installation Precautions 21
- Projection Distance per Screen Size 22
- How to Install the Projector On a Tripod 24
- Kensington Security System 25
MAGIC REMOTE CONTROL 26
- To Register the Magic Remote Control 28
- To Re-register the Magic Remote Control 28
- Using the Magic Remote Control 29
USING THE PROJECTOR 30
- Focus of the Screen Image 30
- Watching With the Projector 31
CONNECTING DEVICES 32
Connecting to HD Receiver, DVD, or External Devices 33
- HDMI Connection 33
Connecting a PC 34
- HDMI Connection 34
Connecting a Laptop 34
- HDMI Connection 34
Connecting Headphones 35
Connecting a Digital Amp 36
MAINTENANCE 37
Cleaning 37
- Cleaning the Lens 37
- Cleaning the Projector Case 37
SPECIFICATIONS 38
SYMBOLS 41

PREPARATION

The pictures may differ slightly from the actual product.
15

Accessories

Accessories included with the projector are show below. Accessories are subject to change without prior notice. New accessories may be added or old ones removed.
Magic Remote Control
Two AA Batteries
AC-DC Adaptor
• When connecting an HDMI or USB cable, or
connecting a USB flash drive to the HDMI or USB port, use a product that has a width of 18 mm or less and a height of 10 mm or less. If the USB cable or USB flash drive does not fit the USB ports of the projector, use an extension cable that supports USB 2.0.
• When connecting two USB devices at the same time, each one should have
bezels less than 8.5 mm thick.
• Use a certified cable with the HDMI logo attached.
• If you do not use a certified HDMI cable, the screen may not display or a
connection error may occur. (Recommended HDMI cable types)
- High-Speed HDMI®/™ Cable
- High-Speed HDMI®/™ Cable with Ethernet
Owner's Manual Power cord
ENGLISH
16

Optional Extras

To purchase optional accessories, visit an electronics store or online shopping site or contact the retail store where you purchased the product. Optional accessories are subject to change without prior notice.
ENGLISH
Projection Screen Tripod HDMI Cable
Audio Cable Optical Cable LG Audio Device

Parts and Components

This projector is manufactured using high-precision technology. You may, however, see tiny black dots and/or bright colored dots (red, blue, or green) that continuously appear on the projector screen. This is a normal result of the manufacturing process and does not indicate a malfunction.
Main Unit
Joystick Button
Speaker
Zoom ring
Focus Ring
Lens
Intake Vent
2)
Bottom of the Projector
Speaker
1)
Vent
17
ENGLISH
Adjustable leg
3)
1) Due to the high temperature of vent area, do not get close to the vent area.
2) Do not touch the Lens and Mirror when using the projector. The Lens and Mirror may be damaged. (Keep lens away from sharp objects.)
3) Turn the adjustable leg left or right to adjust the angle.
18
Back
ENGLISH
IR Receiver
1
OPTICAL DIGITAL AUDIO OUT Port
2
3
4
5
6
7
(Headphone Port)
LAN Port
(USB port)
Port
DC IN Port
1
Description
4
3
2
5
6
7

Using the Joystick Button

You can operate the projector by pressing the button or moving the joystick left, right, up, or down.
Basic functions
Power On When the projector is turned off, place
your nger on the joystick button, press it
once, and release it.
Power Off When the projector is turned on, place
your nger on the joystick button, press
it once for a few seconds, and release it. (However, if the Menu button is on the screen, pressing and holding the joystick button will let you exit the Menu.)
Volume Control
Place your nger over the joystick button
and move it left or right, you can adjust the volume level.
19
ENGLISH
Up/Down/ Left/Right
• Move the joystick button up, down, left, or right. Be careful not to press
the joystick button. If you press the button while moving the joystick, the volume control may not work, and the cursor may not move.
If you move the joystick up, down, left, or right, you can move the cursor to select the menu items.
20
Adjusting the menu
When the projector is turned on, press the joystick button one time. You can adjust the menu items ( , , , ) moving the joystick button left, right, up, or down. Move to the desired menu item, and then press the joystick
ENGLISH
button once to select it.
Turns the power off.
Changes the input source.
Clears on-screen displays and returns to projector viewing.
Displays the Settings menu.

Projector Status Indicators

LED Power
Indicator
LED Power Indicator
Power standby state
Red
The projector is operating with the power on.
Off
21

Installation

Installation Precautions
• Place the projector in a well-
ventilated environment.
- To prevent internal overheating, install the projector in a well­ventilated place. Do not place anything near the projector. That may block its air vents. If the air vents are blocked, the internal temperature of the projector will increase.
- Do not place the projector on a carpet or rug. If the projector's inlet vent is on the bottom, be careful not to block the vent and always use the projector on a solid, level surface.
- Be sure to prevent foreign objects such as paper debris from entering the projector.
- Leave an adequate open area (30 cm or more) around the projector.
ENGLISH
• Do not place the projector in a hot,
cool, or humid environment.
• Do not place the projector in a place
where it will easily attract dust.
- This may result in re.
• Never open any cover on the
projector. There is a high risk of electric shock.
• The projector is manufactured using
high-precision technology. You may, however, see tiny black dots and/ or bright colored dots (red, blue or green) that continuously appear on the projector screen. This is a normal result of the manufacturing process and does not indicate a malfunction.
• The remote control may not work
in an environment where a lamp equipped with electronic ballasts or a three-wavelength fluorescent lamp is installed. Replace the lamp with an international standard lamp for the remote control to work normally.
• To install to the ceiling, attach the
ceiling-type bracket to the projector with M4 x 8 mm screws.
22
Y/2 Y/2
Projection Distance per Screen Size
1  Place the projector on a sturdy, level surface, together with the PC or audio/
video source.
2  Place the projector an appropriate distance away from the screen. The
ENGLISH
distance between the projector and the screen determines the actual size of the image.
3  Position the projector so that the lens is at a right angle to the screen. If the
projector is not at a right angle, the projected image will look distorted. To correct the distortion, use the Edge Adjustment function.
4  Connect the power cord of the projector and the connected device to the wall
outlet.
Ratio of upward projection: 100 %
Screen Height (X)
X/2 X/2
Screen
Screen Width (Y)
Screen
Projection Distance (D)
Tele
Projection Distance (D)
Wide
16:9 Aspect Ratio (Wide)
Screen Size (mm)
762 664 374 905
889 775 436 1061 1016 886 498 1230 1143 996 560 1371 1270 1107 623 1526 1397 1218 685 1682 1524 1328 747 1837 1651 1439 809 1992 1778 1550 872 2147 1905 1660 934 2302 2032 1771 996 2458 2159 1882 1058 2613 2286 1992 1121 2768 2413 2103 1183 2923 2540 2214 1245 3078 2667 2324 1308 3234 2794 2435 1370 3388 2921 2546 1432 3544 3048 2657 1494 3698
Screen Width (Y)
(mm)
Screen Height (X)
(mm)
16:9 Aspect Ratio (Tele)
Screen Size (mm)
693 604 340 905
808 704 396 1061
924 805 453 1230 1039 906 509 1371 1155 1006 566 1526 1270 1107 623 1682 1385 1208 679 1837 1501 1308 736 1992 1616 1409 792 2147 1732 1509 849 2302 1847 1610 906 2458 1963 1711 962 2613 2078 1811 1019 2768 2194 1912 1075 2923 2309 2013 1132 3078 2425 2113 1189 3234 2540 2214 1245 3388 2655 2314 1302 3544 2771 2415 1358 3698
Screen Width (Y)
(mm)
Screen Height (X)
(mm)
23
Projection Distance
(D) (mm)
ENGLISH
Projection Distance
(D) (mm)
24
CAUTION
How to Install the Projector On a Tripod
• You can install the projector using a camera tripod.
• As shown below, you can mount the projector instead of a camera on the tripod.
• When stabilizing the tripod, we recommend using a locking bolt of standard size
ENGLISH
4.5 mm or less. The maximum size allowed for the locking bolt is 5.5 mm. (If it is longer than the maximum allowed size, it may damage the projector.)
Bottom of the
Projector
Bolt used to attach the projector to the tripod
The projector
is connected to
this part.
Tripod
• If you are using a tripod, be careful not to apply external force to the tripod.
Doing so may damage the projector.
• Do not place the tripod on an unstable surface.
• Be sure to use a tripod with a maximum load capacity of 3 kg or more.
• To use the projector safely, position the tripod legs so that they are as wide
and stable as possible and be sure to securely attach the projector to the tripod.
25
Kensington Security System
• This projector has a Kensington Security Standard connector as an anti-theft
mechanism. Connect a Kensington Security System cable as shown below.
• For more information on installation and use of the Kensington Security System,
refer to the user’s guide provided with the Kensington Security System.
• The Kensington Security System is an optional accessory.
• What is Kensington?
Kensington is a company that provides safety systems for laptops and other electronic devices. Website: http://www.kensington.com
ENGLISH
26

MAGIC REMOTE CONTROL

If the battery low message appears while using the Projector, replace the batteries.
ENGLISH
As shown in the gure, press the top of the battery
cover and slide it down the cover. Insert two new and identical batteries (1.5 V, AA type) with + and - poles pointing in the correct direction in the remote control.
•Do not mix new batteries with old ones.
(POWER)
Turns the Projector on or off.
(STB POWER)
You can turn your set-top box on or off by adding the set-top box to the universal remote control for your Projector.
Number buttons
Enters numbers.
Change the input source to HDMI1.
(Screen Remote)
Displays the Screen Remote.
- Accesses the Universal Control Menu in some regions.
1
2
Adjusts the volume level.
(MUTE)
Mutes all sounds.
Moves to the previous/next page.
(SEARCH)
Search for content such as movies and other videos, or perform a web search by entering your search terms in the search box.
27
Accesses the Home menu.
*
Shows the previous history.
Displays the set-top box Home menu. (When you are not watching with a set-top box: the set-top box screen is displayed.)
Press the up, down, left or right button to scroll the menu. If you press use, the pointer will disappear from the screen and Magic Remote will operate like a general remote control. To display the pointer on the screen again, shake Magic Remote to the left and right.
Wheel (OK)
Press the center of the menu. You can change pages by using the Wheel button.
Returns to the previous screen.
Clears all on-screen displays and returns to Projector viewing.
Changes the picture mode.
Allows you to use the SIMPLINK function.
(INPUT)
Changes the input source.
- Pressing and holding the the lists of external inputs.
(Q. Settings)
Accesses the Quick Settings.
- Pressing and holding the the All Settings menu.
Coloured buttons
These access special functions in some menus. (
Control buttons (
You have access to premium content, video content and devices that support SIMPLINK.
Changes the aspect ratio of the screen per pressing of the button.
(Up/Down/Left/Right)
buttons while the pointer is in
Wheel (OK) button to select a
*
(INPUT) button displays all
(Q. Settings) button displays
: Red, : Green, : Yellow, : Blue)
, )
ENGLISH
* : To use the button, press and hold for more than 3 seconds.
28

To Register the Magic Remote Control

To use the Magic Remote control, register it with your projector rst.
1  Put batteries into the Magic Remote and turn the Projector on. 2  Point the Magic Remote at your projector and press the Wheel (OK) on
ENGLISH
the remote control.
• If the projector fails to register the Magic Remote, try again after turning the
projector off and back on.
To Re-register the Magic Remote Control
1  Press the and buttons at the same time, for ve seconds, to unpair
the Magic Remote with your projector.
2  Press the Wheel (OK) button towards the projector to re-register the
magic remote control.
• Pressing and holding the button will let you cancel and re-register
Magic Remote at once.
Using the Magic Remote Control
CAUTION
• Shake the Magic Remote slightly to the right and
left or press , (INPUT) buttons to make the pointer appear on the screen.
• If the pointer has not been used for a certain period
of time or Magic Remote is placed on a flat surface, then the pointer will disappear.
• If the pointer is not responding smoothly, you can
reset the pointer by moving it to the edge of the screen.
• The Magic Remote depletes batteries faster than a
normal remote due to the additional features.
• Use the remote control within the specified range (within 10 m). You may
experience communication failures when using the device outside the coverage area or if there are obstacles within the coverage area.
• You may experience communication failures depending on the accessories.
Devices such as a microwave oven and wireless LAN operate in the same frequency band (2.4 GHz) as the Magic Remote. This may cause communication failures.
• The Magic Remote may not work properly if a wireless router (AP) is within
1 m of the projector. Your wireless router should be more than 1 m away from the projector.
• Do not disassemble or heat the batteries.
• Do not drop the battery. Avoid extreme shocks to the battery.
• Inserting a battery in the wrong way may result in explosion.
29
ENGLISH
30

USING THE PROJECTOR

Focus of the Screen Image

ENGLISH
When an image appears on the screen, check if it is in focus and ts the screen
properly.
Zoom Ring
Focus Ring
• To adjust the focus of the image, rotate the focus ring.
• To adjust the size of the image, rotate the zoom ring. To move the screen image
upward/downward, adjust the height of the foot at the bottom of the projector.
Loading...
+ 96 hidden pages