LG GM730F Users manual

GM 730f User Guide

This device is not intended for sale in the USA.

- English

This document is the user guide for the GM730f

Windows Mobile Pocket PC. All rights for this document are reserved by

LG Electronics. Copying, modifying and distributing this document without

the consent of LG Electronics are prohibited.

Part 15.21 statement

" Change or Modifications that are not expressly approved by the manufacturer could void

the user's authority to operate the equipment. “

Part 15.105 statement

This equipment has been tested and found to comply with the limits for a class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Part 15 Class B Compliance

This device and its accessories comply with part15 of FCC rules.

Operation is subject to the following two conditions:

(1) This device & its accessories may not cause harmful interference.

(2) This device & its accessories must accept any interference received,

including interference that may cause undesired operation.

Body-worn Operation

This device has been tested for typical body-worn operations

with the distance of 0.79inches (2.0cm) from the user’s body.

To comply with FCC RF exposure requirements, a minimum separation distance

of 0.79inches(2.0cm) must be maintained from the user's body.

Additionally, Belt clips, holsters & other body-worn accessories may not contain

metallic components.

Getting Started

Installing the SIM Card and Battery

1. Installing the SIM card.

Your SIM card contains your phone number, service details and contacts and must be inserted into your handset. If your SIM card is removed then your handset becomes unusable (except for emergency calls depending on which Country you are in at the time) until a valid one is inserted. Always disconnect the charger and other accessories from your handset before inserting and removing your SIM card. Slide the SIM card into the SIM card holder. Make sure that the SIM card is properly inserted and the gold contact area on the card is facing downwards. To remove the SIM card, press down lightly and pull it in the reverse direction.

Note

The metal contact of the SIM card can easily be damaged by scratches. Pay special attention to the SIM

card while handling. Follow the instructions supplied with the SIM card.

2. Installing the battery.

Insert the Battery into the battery compartment as the metal contacts meet in the middle of the phone. Push down the top of the battery until it snaps into place. Place the battery cover to the phone as shown.

Charging the Battery

Before connecting the charger to the phone you must first check the battery is installed.

Getting Started

When you recharge your phone after device switch off, the phone displays a charging animation.

When the phone is fully charged, the animation displays “Battery Charging Complete”.

When the battery is fully discharged, animation is not displayed.

During the animation displays “ Battery is too low”, you cannot power on the phone to get sufficient

power for booting.

As soon as charged power reach 1% (need 1 or 2 minutes), charging animation is displayed. And you

can power on the phone.

If you press and hold the power button for approx. 2 seconds in charging mode, the phone is turned on.

CAUTION!

• When you charge a fully discharged battery, it may take over a minute for the display to respond. This is not a malfunction but completely normal. (If using a USB cable, it may take over 10 minutes.)

Getting Started

• Do not force the connector as this may damage the phone and/or the charger.

• If you use the charger out of your own country, use an attachment plug adaptor for the proper configuration.

• Do not remove your battery or the SIM card while charging.

• There is risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the maker's instructions.

WARNNING

• Unplug the charger from the mains and phone during lightning storms to avoid electric shock or fire.

• Make sure that no sharp-edged items such as animal teeth or nails come into contact with the battery. There is a risk of this causing a fire.

Disconnecting the Charger

Disconnect the travel adapter from the phone as shown in the diagram. Make sure you pull by the plug, not the cord.

How to Use a MicroSD Memory Card (Optional)

Lift the plastic cover which protects the microSD slot.

Insert the memory card into the slot with the metal contacts facing down. Do not force the memory

card into the slot, if the card does not slide in easily, please check that the card is being inserted the correct way or if there is a foreign object in the slot.

Once inserted, push the memory card until you hear a

correctly engaged.

Close the plastic slot protection.

Do not remove the memory card when reading/writing the memory card.

Click

, meaning that the microSD has been

Getting Started

Attention:

Avoid using the microSD memory card when the battery is low.

When writing to the card, wait for the operation to complete before

removing the card.

The card is designed to fit easily into the system one way only.

Do not bend the card or force it into the slot.

Do not insert any memory cards other than microSD.

Supports up to 32GB microSD. For more information on the microSD, please refer to the memory card instruction manual.

Memory Card Formatting

Before you start to use the memory card you have to format it. A message will pop up after you insert the memory card notifying you to format the memory card.

Getting Started

Note

Usually the microSD has already been formatted.

Turn the Device On and Off

To turn on the device, press the button. When you turn on the device for the first time, you are asked to complete a calibration process. For more information, see “Calibrate the device” on next page.

To turn off the device, press again.

Reset the Device

Occasionally you may need to reset your device. A normal (or soft) reset of your device clears all active program memory and shuts down all active programs. This can be useful when the device is running slower than normal, or a program is not performing properly. A soft reset is also necessary after the installation of some programs. If a soft reset is performed when programs are running, unsaved work will be lost.

You can also perform a hard reset (also known as a full reset). A hard reset should be performed only if a normal reset does not solve a system problem. After a hard reset, the device is restored to its default settings—the way it was when you first purchased it and turned it on. Any programs you installed, data you entered, and settings you customized on the device will be lost.

To perform a soft reset

• Find out Soft reset key which is small hole at the left side of your device shown enclosed by circles in the picture below. Use the stylus to press the reset key and hold it for a while. Your device may shut down. Press the POWER button, the device restarts and displays the Today screen. A soft reset of your device clears all active program memory and shuts down all active programs. This can be useful when your device is running slower than normal, or a program is not performing properly. A soft reset is also necessary after the installation of some programs. If a soft reset is performed when programs are running, unsaved work will be lost.

Getting Started

To perform a hard reset

• A Hard Reset should only be performed after all other trouble shooting options have been exhausted. After a hard reset, the device is restored to its default settings - the way it was when you first purchased it and turned it on. Any programs you installed, data you entered, and settings you customized on your device will be lost.

Power the device ON

Tap

Start

Settings

Enter 1234 for the password twice.

Press Enter.

Select what to reset.

You have to enter your password and confirm again for hard reset. However when you forget your password, the only way to hard reset the device is via the hard key sequence.

Power the device OFF.

Press and hold the following hard keys in sequence.

+ +

System

tab >

Clear Storage

Getting Started

Keep pressing keys until your LCD screen turns on. Align screen will appear if you success hard key reset.

Calibrate the Device

Calibrating the device screen involves tapping with the stylus the center of a cross as it moves around the screen. This process ensures that when you tap the screen with your stylus, the tapped item is activated.

If your device does not accurately respond to screen taps, follow these steps to re-calibrate it:

Tap

Start

Settings

On the

Genera

completed, Align screen reappears. Click OK on upper right corner to return to setting mode.

l tab, tap

System

tab >

Align Screen

Screen

, and follow the instructions on the screen. After calibration is

Manage Screen Settings

The device touch screen has three orientation modes: Portrait, Landscape (right-handed), and Landscape (left-handed). Portrait mode allows you to get a better view or a better operation of certain programs on your device, while Landscape mode may be optimal for viewing longer text files.

To change the orientation, tap

orientation you want. If Accelerometer Sensor is turned on (check (

Sensor

of screen display when the orientation for device is changed.

To smooth the edges of screen fonts for many programs, on the

System

To increase the readability or to see more content on the screen, on the

(tap

), rotation sensor automatically perceive the orientation of your device and decide to direction

tab >

Start

Screen

Settings

), select the

System

Start

Settings

Enable ClearType

tab >

Screen

System

LG Menu

), adjust the text size by moving the slider.

tab >

Screen

) >

Settings > Sensor

check box.

General

ClearType

Text Size

tab, and select the

Accelerometer

tab(tap

Start

tab

Settings

Getting Started

Screen information

The Today Screen

Customising the Today screen

The Today screen displays important information, such as upcoming appointments and status indicators. You can tap a section on the screen to open the associated program.

To access the Today screen, tap

You can select the item you want to appear on the Today screen. To change its position, tap

Move Down

. If you want to customise the further task and appointment information by tapping

(

LG Menu) > Settings > Today > Items

tab.

Move up

Options

Check the after the specified length of time has elapsed, the screen switches to the Today screen.

To synchronise the Today screen display, including the background image, tap

You can select the desired theme for the background. If you use your own background image, tap the

this picture as the background

Screen information

Today timeout

Settings > Today > Appearance

select the number of hours from the drop down list. If you don't use your phone

and tap

tab.

Browse

to locate the file you want.

(

LG Menu)

Use

Default MS Today Screen

On the Today screen, you can see important and recent information for the day.

1. Start button:

2. LGdatetime:

3. Phone information:

4. Service provider name:

5. Unread message:

6. Get Xpress Mail:

7. Upcoming Appointments:

8. No new missed calls:

9. IM:

Go to Instant Message program menu.

10. Indicators:

11. Weather:

12. Calendar:

13. Contacts:

Shows the Start menu that you can use directly.

Shows today's date and current time. Tap to select the clock type.

Wireless Manager / Bluetooth phone on or off.

Shows your service provider name.

You can see the unread message from Inbox account.

You can install Xpress Mail application.

You can see the upcoming schedule.

You can see the missed call history.

Connectivity, SIM card, Volume and Battery indicator.

You can check today's weather. Tap to see more detail weather forecast.

Link to Calendar

Link for Contacts list

Screen information

Indicators

Following are some of the status icons that you may see on your device.

Icon Description

Bluetooth Hands-Free connection established

Bluetooth Hands-Free channel opened

Bluetooth High Quality Audio channel opened

Indicates the remained battery power .

Indicates the battery is very low.

Battery charging.

Sound on.

Sound off.

Ringer in vibration mode.

Connection is active.

Connection is not active.

Synchronization in progress.

Synchronization error.

Indicates maximum signal strength.

No signal.

Indecates Bluetooth service.

Screen information

No phone service.

Searching for phone service.

Voice call in progress.

Icon Description

Calls are forwarded.

Call on hold.

Missed call or rejected call.

GPRS (General Packet Radio Services) available

EDGE (Enhanced Data Rates For Global Evolution) available

WCDMA or HSDPA available

New e-mail or text messages.

New voice mail

There are more notifications. Tap the icon to view all.

SIM is not inserted. You can not use Network service without SIM.

Shows the list of running Applications by tapping this indicator.

Using the Start Menu

The Start menu, located at the top left corner of the Today screen, displays a list of programs. It lets you open a screen and switch from one program to another. You can start a program by scrolling through the programs list and tap a program.

Editing the Today Screen

Tap to open the Today screen.

Tap to start a program. The items displayed in Start menu can be synchronised by tapping

Settings

Tap to start a recently-used program.

Tap to view and select more programs that are installed in your device.

Tap to change device settings.

Tap to see a Help topic for the current screen.

Personal

tab >

Menus

Start

Screen information

Program Indicators

Following are some of the icons for the programs that are already installed on your device.

Icon Name (Path) Description

Apps

(Tap

LG Menu

Multimedia

Apps

) Use pre-installed applications.

AT&T GPS

voice guided turn-by-turn GPS driving directions with real time traffic based navigation.

AT&T Music

streaming media, and access AT&T's 1 music player.

Games (Tap LG Menu > Multimedia > Games)

Bubble Breaker, MsPac-Man, Solitaire and Sudoku.

MEdia Mall

multimedia, tones, videos and other applications.

Messaging

messages.

Tools

mobile device. File Explorer, GPS Utility, Java, etc..

Active Sync

between your device and a PC.

Browser

downloads new programs and files from the Internet.

Cellular Video

and entertainment clips via AT&T’s high-speed data network while on the go.

Internet Sharing

Screen information

internet sharing device.

MEdia Net

(weather, news, etc.) and download ringtones or other personalization items.

(Tap

LG Menu > Applications > AT&T GPS)

(Tap

LG Menu > Multimedia > AT&T Music

(Tap

LG Menu > Multimedia > MEdia Mall)

(Tap

LG Menu > Communication > Messaging)

(Tap

LG Menu > Applications > Tools

(Tap

LG Menu > Communication > ActiveSync)

(Tap

LG Menu > Applications > Browser)

(Tap

LG Menu > Multimedia > Cellular Video)

(Tap

LG Menu > Applications > Internet Sharing)

(Tap

LG Menu > Multimedia > MEdia Net)

Helps you get around town by providing

) Shop for music, songs, music videos,

Play pre-installed games: Block Breaker Deluxe,

Shop for games, musics, graphics,

Sends and receives e-mail and text

) Access some array of tools and utilities on your

Synchronizes information

Browses Web and WAP sites, and

Watch news, sports, weather,

Use your device as a

Browses to access your favorite content

Modem Link (Tab Start > Programs) Notes

(Tap

LG Menu > Applications > Notes)

and recordings

Pictures & Videos

sorts picture and video files in the My Pictures folder of your device or on a storage card.

(Tap

LG Menu > Multimedia > Pictures & Videos)

Use your mobile device as a modem.

Creates handwritten or typed notes, drawings,

Collects, organizes, and

Icon Name (Path) Description

Stopwatch

time of an event. The duration of an individual lap time (up to 99 times) and the total time can be displayed.

Task Manager

Tasks

Windows Media

on your device.

(Tap

LG Menu > Applications > Stopwatch)

(Tap

LG Menu > Settings > Task Manager)

(Tap

LG Menu > Communication > Tasks)

(Tap LG Menu

Settings

Allows you to record the elapsed

Check activating task information.

Keeps track of your tasks.

Multimedia > Windows Media)

Enables the multimedia function

You can adjust the device settings to suit the way you work. To see all available settings, tap

Settings

, then tap the

Personal, System

, and

Connections

tabs located at the bottom of the screen.

Personal tab

Icon Description

Buttons

Clock Style & Weather Gesture

exclusive programs.

Input

Lock

Lock Key

Menus

Owner Information

Phone Sounds & Notifications

notification for different events.

Assign a program or function to a hardware button.

Select clock style. Weather also be set specified information.

Enable to recognize your flicking gesture. Adjusting click sensitivity and select

Set options for each of the input methods.

Set a password for your device.

Enables or disables the handset's Keypad Lock key.

Set what programs will appear in the Start menu.

Enter your personal information on your device.

Customize phone settings such as ring tone, set a PIN number for your SIM card, and more.

Enable sounds for events, notifications, and more, and set the type of

Start

Screen information

Today

Customize the appearance and the information to be displayed on the Today screen.

TTY

Enable TTY (Teletypewriter) support for your device.

Screen information

Icon Description

Voice Command

command is enabled.

System tab

Icon Description

About

This is where you can see basic information such as the Windows Mobile® version and

type of processor used on your device. You can also specify a name for your device.

Backlight

Certificates Clear Storage

memory and reset your device to factory default settings.

Clock & Alarms

zone when you’re traveling. Alarms can also be set at specified days and times of a week.

Customer Feedback

sending your feedback to Microsoft.

Encryption

only on your device.

Error Reporting External GPS

when there are programs on your device that access GPS data or you have connected a GPS receiver to your device. See Help for details.

LG X Button

the button.

Set the backlight timeout and adjust brightness.

Enable to use Voice Command function. Select the items where are voice

See information about certificates that are installed on your device.

Tap this icon only when you need to remove all your data and files from the

Set the device clock to the date and time of your locale or to a visiting time

You can participate the Customer Experience Improvement Program by

Allow files on your storage card to be encrypted. Encrypted files will be readable

Enable or disable error reporting when errors are occured on your device.

Set the appropriate GPS communication ports, if required. You may need to do this

Stop running programs and set the "X" button to end programs immediately when you tap

Screen information

Managed Programs Memory

stop currently running programs.

Power

display (switching device to Sleep mode) to conserve battery power.

Regional Settings

numbers, currency, date, and time on your device.

Remove Programs

Check the device memory allocation status and memory card information. You can also

Check the remaining battery power. You can also set the timeout for turning off the

This is where you can see installation history of your device.

Set the regional configuration to use, including the format for displaying

Remove programs that you installed on your device.

Icon Description

Screen

Sensor

System information

Task Manager

Time Auto update

Video Share Windows Update

with the latest security patches or fixes.

Change the screen orientation, re-calibrate the screen, and change the screen text size.

Set your Auto Luminous Control and Proximity sensor to use or not.

Connections tab

Icon Description

Bluetooth

and type of processor used on your device. You can also specify a name for your device.

Connections

dial-up, GPRS, and more, so that your device can connect to the Internet or a private local network.

Domain GPRS Setting

USB to PC

ActiveSync on the computer is unable to detect the device.

Wi-Fi

Enroll Connect your device with company resources.

Allows you to customize Wi-Fi settings.

Check your system information and storage information.

Shows the executing application list.

If Auto update sets On, current city time will follow the network time.

You can change the Video share default settings.

Link to Microsoft's Web site and update Windows Mobile® on your device

This is where you can see basic information such as the Windows Mobile® version

Set up one or more types of modem connections for your device, such as phone

Set the GPRS authentication method.

Enhances the connection between the device and the computer, in situations when

Wireless LAN Wireless Manager

Phone.

Shows information about the active wireless network.

Allows you to manage all of wireless settings such as Wi-Fi, Bluetooth and

Screen information

Entering and Searching Information

You are available to the various input methods on the screen, including

Trnscriber

method is currently selected. The Input Selector arrow (shown at the right side of the Input Panel icon) opens a list of available input methods.

, and

XT9 Keypad

. The Input Panel icon appears on the menu bar to indicate which input

Keyboard, LGJavaKey

Overview of Input Panel

To change the input method, tap the Input Selector arrow.

Icon Indicates the selected input method is

The on-screen keyboard.

Transcriber.

LGJavaKey XT9 Keypad

Using the Keyboard

To enter text, symbols, and numbers, you can either type using the QWERTY Keyboard to type ABC charanters or the standard on-screen

Keyboard

Entering and Searching Information

Using the standard on-screen Keyboard

The on-screen Keyboard is available when text entry is possible. You can enter text by tapping keys on the keyboard that are displayed on the screen.

Enter text using the on-screen keyboard

The on-screen keyboard is available when text entry is possible.

To make the keys larger, tap the Input Selector arrow, and then

select

Keyboard

General rule for entering text is same as MS based PC.

, and then tap

Large Keys

Options

. In the

Input method

list,

Using the LGJavaKey

You can use as navigation keys (left/right/up/down/center) when your Java applications are

launched.

You can move the cursor and select menu on out of Java application.

XT9 Keypad

With XT9 keypad, you can enter text by tapping keys displayed on the screen. This is the most common way to enter text with word prediction function in 20 Qwerty of portrait screen.

XT9 Keypad is available when text entry is possible.

Enter letters by tapping the keys labelled with the required letters.

There are four input modes and you can change by tapping Fn, T9/123 and abc/123. You can turn

on and off XT9 prediction function by tapping Fn and T9/123 or abc/123 successively. If you tap just T9/123 or abc/123, you can enter 123 mode. If you tap just Fn, you can enter symbol mode.

XT9 mode

If you turn on XT9 mode by tapping Fn and T9/123 successively, you can enter words with only one keystroke per letter. The XT9 mode automatically compares your keystrokes with an internal dictionary to determine the correct word, thus requiring far fewer keystrokes than the traditional multitap mode. This is sometimes known as predictive text. This feature is supported only in portrait screen.

Entering and Searching Information

ABC mode

If you turn off XT9 mode by tapping Fn and abc/123 successively, you can enter letters by tapping the key labeled with the required letter once or twice until the correct letter is displayed. Tap once for the first letters and twice for the second letters. This mode is known as multitap mode.

Entering and Searching Information

123 mode

If you tap T9/123(abc/123), you can enter 123 mode. Type numbers using one keystroke per number. You can also enter additional symbols in 123 mode.

Symbol mode

Short press of FN key gives symbol for one key press, and long press of FN locks symbol mode. The symbol mode enables you to enter various symbols or special characters.

You can enter extra symbols by tapping Sym key in full qwerty.

CAPS

Short press switches to uppercase for one keypress, long press switches to caps lock mode.

Portrait mode:

Landscape mode:

Touch for switching to symbol keypad. Switch to letter keypad again after one key input. If you want to lock symbol keypad, press and hold the icon.

Tap this key for entering Symbols or turning XT9 on and off.

Tap this key for entering Symbols and numbers.

Entering and Searching Information

Arrow key in full qwerty

Pressing the arrow key will hide the menu bar and show the bigger text area.

Using Transcriber

Transcriber

combination of both. Transcriber works transparently in the background of programs, recognizing words with its integrated dictionary. When Transcriber is turned on, it interprets stylus movement anywhere on the screen as handwriting input. For more information about using Transcriber, see Help on your device.

is a handwriting recognition program that allows you to write in cursive, print, or a

To start Transcriber

Start a program that accepts user input, such as Word Mobile.

Tap the Input Selector arrow, and tap Transcriber. The Transcriber introductory screen appears.

To write using Transcriber

In a program, position the cursor where you want text to appear.

Use the stylus to write anywhere on the screen. The handwriting will be converted to text shortly after

you lift the stylus from the screen.

To enter punctuation and symbols

Transcriber comes with an on-screen keyboard that provides an easy way to add punctuation or a special symbol to existing text.

From a program, tap

on the Transcriber toolbar. The keyboard remains visible until you tap the

button again.

Note

To reposition the keyboard, tap and hold the title bar, then drag to the desired location.

When no text is selected, you can also open the keyboard by doing the gesture.

To edit text

In a program, draw a line across the text you want to edit.

After you lift the stylus from the screen, the line will disappear and the selected text will be

highlighted.

Do either of the following:

Rewrite the text.

Use gestures to capitalize letters, insert a space, and so on.

Entering and Searching Information

Transcriber Gestures

Use quick strokes of the stylus to edit your text or to insert returns, spaces, or tabs.

Do To

Insert a paragraph return at the cursor.

The horizontal portion of the gesture must be at least two times longer than the vertical portion.

Insert a space at the cursor.

The horizontal portion of the gesture must be at least two times longer than the vertical portion.

Move the cursor one space back and erase any text.

Do the gesture by drawing a line from right to left.

Open the menu of alternate words if a word is selected or the onscreen Transcriber keyboard if no text is selected.

Do the gesture by drawing a line straight down and back up.

Entering and Searching Information

Change the capitalization of a selected letter, word, or block of text.

Do the gesture by drawing a line straight up.

Undo the last action.

Do the gesture by drawing a line straight up and back down.

Copy the selected text.

Do the gesture by drawing a line from left to right and back.

Cut the selected text.

Do the gesture by drawing a line from right to left and back. Paste copied or cut text.

Do the gesture by drawing a line from the lower left of the screen diagonally up toward the right and back down to the right.

Insert a tab.

The horizontal portion of the gesture must be at least two times longer than the vertical portion.

Note

You can also use the Enter, Space, and Backspace buttons on the Transcriber toolbar.

The Transcriber toolbar

Tap To

You can set the transcriber options such as writing direction, text and shorthand.

You can set the shape of letters as your handwriting.

You can enter numbers, punctuation and symbols.

You can change text input methods.

• a mode. This is the default for optimum handwriting recognition.

• 123 mode. Numbers and some letters are allowed and the calculator is activated.

A mode. All letters are automatically capitalized.

•

If you are in A or 123 mode, recognition returns automatically to the default mode once you lift the stylus.

You can insert a space at the cursor.

You can insert a paragraph return at the cursor.

You can insert the cursor one space to the left.

You can move the cursor one space to the right.

Back and erase any text.

Help

Entering and Searching Information

Drawing and Writing on the Screen

You can draw directly on the screen, or write on the screen and save notes in your own handwriting. To do this, you must set the input mode in Notes to If you prefer to use handwriting or frequently add drawings to your notes, you may find it helpful to set Writing as the default input mode. If you prefer typed text, set

To set the input mode for Notes

Tap (

In the note list, tap

In the

v v

Tap OK.

To write a note

LG Menu)

Default mode Writing Typing

if you want to draw or enter handwritten text in a note.

if you want to create a typed note.

Applications

box, tap one of the following:

Options

Notes

Writing

Typing

as the default input mode.

Entering and Searching Information

Tap (

In the note list, tap

Write your text on the screen.

When finished, tap OK to return to the note list.

Note

LG Menu)

To select handwritten text, tap and hold next to the writing. As soon as dots appear, and before they

form a complete circle, quickly drag across the writing. If a letter crosses three ruled lines, it is treated as a drawing rather than text.

Applications

New

Notes

To draw in a note

Tap (

In the note list, tap

To draw on the screen, use the stylus like a pen.

A selection box appears around your drawing.

When finished, tap OK to return to the note list.

Note

LG Menu)

To select a drawing (for example, to copy or delete it), tap and hold the drawing briefly. When you lift the

stylus, the drawing is selected.

Applications

New

Notes

Picsel Viewer Pan and Zoom Mode

The document you wish to see is often larger than the space available on the screen. There are two ways to see more of it. To pan (or ‘scroll’) to a different part of the document, simply stroke your pen across the screen in the direction you would like the page to move.

To pan the page up, touch and hold your pen somewhere near the middle of the screen and draw a line towards the top, then take your pen off the screen. You can do this repeatedly so that you can view any size of document. Further, you can ‘throw’ the document across the screen, and it will continue moving after you have released the pen. This gives you time to start another stroke. This inertia can be used to save time while you pan around the document.

Entering and Searching Information

You can also zoom the size of the document, so that more or less of it is visible at a different size. The tap-and-stroke gesture for this is to tap your pen briefly near the middle of the screen then touch and hold it again in the same place (a “double-tap”). Now, stroke your pen up to zoom in, or down to zoom out. Release your pen when you reach the scale you like. Using this, you can view small print details on diagrams, or can get an overview of a whole page.

Entering and Searching Information

Thumbnail

While viewing a page, a thumbnail can be displayed to:

- Give an overview of the current page

- Show the position of the current visible screen on the page

Currently, there are two modes that can be used. For document map mode, the visible area of the document is the same, and the thumbnail is superimposed at the bottom of the screen, on a transparent panel. A red transparent box on top of this thumbnail shows the current screen position and size. For magnify mode, the screen is split in two. A magnifying glass icon can be used to navigate the thumbnail at the top, and the bottom portion shows the zoomed document.

Find text in a PDF

You can search a word or words in a PDF file. The Find menu searches the currently open PDF

1. Select Search > Find menu. Then search dialog is shown.

Entering and Searching Information

2. Type the text you want to search.

3. Press OK.

* This viewer doesn’t use exact case match.

Quick reference

Search > Find

Search > Find prev

Search > Find next

Search > Snap to result

Search > Cancel

Thumbnail > Off

Thumbnail > Document map

Thumbnail > Magnify

Goto > Page

Goto > First

Goto > Prev

Goto > Next

Goto > Last

Find the word in this document

Find the word before current focused word

Find the word after current focused word

Move to current focused word

Cancel finding the word

Off the thumbnail

View the document map

View the document through magnifying glass

Go to page where you want

Jump to the first page

Go to the previous page

Go to the next page

Jump to the last page

Entering and Searching Information

Recording a Note

You can create a stand-alone recording (voice note) or you can add a recording to a note.

To create a voice note

Tap (

Do one of the following:

To create a stand-alone recording, record from the note list.

To add a recording to a note, create or open a note.

If you do not see the Recording toolbar, tap

Hold your device’s microphone near your mouth or other source of sound. Press the recording button

from the Recording Toolbar.

If you adding a recording to a note, tap OK to return to the note list when finished.

If you are recording in an open note, an icon will appear in the note.

If you are creating a stand-alone recording, the recording will appear in the note list.

LG Menu) > Applications > Notes

View Recording Toolbar

Entering and Searching Information

To change recording formats

Tap

Start

Settings

Tap the

Tap OK.

Note

Options

You can also change recording formats from within Notes. In the note list, tap Menu > Options > Global

Input Options link (at the bottom of the page).

Personal

tab, and in the

tab >

Input

Voice recording format

list, tap the format you want.

Searching Information

You can search for files and other items stored on your device in the My Documents folder or on a storage card. You can search by file name or by words located in the item. For example, you can search in e-mail messages, notes, appointments, contacts, and tasks, as well as in online Help.

To search for a file or an item

Tap (

If you have looked for this item before, tap the

Tap

The

In the

LG Menu) > Applications > Search.

Search for

Type

Search My Documents

Results

, enter the file name, word, or other information you want to search for.

, select a data type to help narrow your search.

folder and subfolders are searched.

list, tap the item you want to open.

Search for

arrow and select the item from the list.

Entering and Searching Information

+ 111 hidden pages