LG 55EA9800-UA Service manual

Internal Use Only

North/Latin America http://aic.lgservice.com Europe/Africa http://eic.lgservice.com Asia/Oceania http://biz.lgservice.com

OLED TV

SERVICE MANUAL

CHASSIS : EA34D

MODEL : 55EA9800 55EA9800-UA

CAUTION

BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

Printed in KoreaP/NO : MFL67840104(1308-REV01)

CONTENTS

CONTENTS .............................................................................................. 2

PRODUCT SAFETY ................................................................................. 3

SPECIFICATION ....................................................................................... 4

ADJUSTMENT INSTRUCTION .............................................................. 11

EXPLODED VIEW .................................................................................. 23

SCHEMATIC CIRCUIT DIAGRAM ..............................................................

Only for training and service purposes

- 2 -

SAFETY PRECAUTIONS

IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.

It will also protect the receiver and it's components from being damaged by accidental shorts of th e cir cuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 MΩ and 5.2 MΩ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exp ose d metallic par t. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to

0.5 mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

Only for training and service purposes

- 3 -

SERVICING PRECAUTIONS

CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conict between the

following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power source before;

a. Removing or reinstalling any component, circuit board mod-

ule or any other receiver assembly.

b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its assemblies.

4. Unless specied otherwise in this service manual, clean

electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10 % (by volume) Acetone and 90 % (by volume) isopropyl alcohol (90 % - 99 % strength)

CAUTION: This is a ammable mixture. Unless specied otherwise in this service manual, lubrication of

contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.

7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last.

8. Use with this receiver only the test xtures specied in this

service manual.

CAUTION: Do not connect the test xture ground strap to any

heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES

devices are integrated circuits and some eld-effect transistors

and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some solder

removal devices not classied as “anti-static” can generate electrical charges sufcient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate

electrical charges sufcient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your

foot from a carpeted oor can generate static electricity sufcient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 °F to 600 °F.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25 cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique

a. Allow the soldering iron tip to reach normal temperature.

(500 °F to 600 °F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature

(500 °F to 600 °F)

b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder ows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

Only for training and service purposes

- 4 -

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent at against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and solder it.

3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete Transistor Removal/Replacement

1. Remove the defective transistor by clipping its leads as close as possible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

Power Output, Transistor Device Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as possible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit board.

3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

At Other Connections

Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

Fuse and Conventional Resistor Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow stake.

2. Securely crimp the leads of replacement component around notch at stake top.

Only for training and service purposes

- 5 -

SPECIFICATION

NOTE : Specifications and others are subject to change without notice for improvement

.

1. Application range

This spec sheet is applied LED TV with (LA34N) chassis

2. Test condition

Each part is tested as below without special notice.

1) Temperature : 25 ºC ± 5 ºC(77 ± 9 ºF) , CST : 40 ºC±5 ºC

2) Relative Humidity: 65 % ± 10 %

3) Power Voltage

Market Input voltage Frequency Remark

USA 110~240V 50/60Hz Standard Voltage of each

product is marked by models

4) Specification and performance of each parts are followed ea ch drawing and s pe cificatio n b y p art number in accordance with BOM

5) The receiver must be operated for about 20 minutes prior to the adjustment

3. Test method

1) Performance: LGE TV test method followed

2) Demanded other specification

Safety : UL, CSA, CE, IEC specification EMC: FCC, ICES, CE, IEC specification Wireless : Wireless HD Specification (Option)

4. General Specification

No Item Specication Remark

1 Market 1) North America

2 Broad casting System 1) ATSC / NTSC-M

3 Receiving System 1) ATSC / NTSC-M

4 Input Voltage AC 100 - 240V ~ 60Hz

5 Available Channel 1) VHF : 02~13

2) UHF : 14~69

3) DTV : 02-69

4) CATV : 01~135

5) CADTV : 01~135

7 Aspect Ratio 16:9

8 Tuning System FS

9 LCD Module LC550LUD-MFP2 LGD 55EA9800-UA

10 Operating Environment 1) Temp : 0 ~ 40 deg

2) Humidity : ~ 80 %

11 Storage Environment 1) Temp : -20 ~ 60 deg

2) Humidity : ~ 85 %

Only for training and service purposes

- 6 -

5. External input format

5.1. 2D mode

5.1.1. Component input (Y, CB/PB, CR/PR)

No. Resolution H-freq(kHz) V-freq.(kHz) Pixel clock Proposed

1. 720*480 15.73 60.00 13.5135 SDTV ,DVD 480I

2. 720*480 15.73 59.94 13.50 SDTV ,DVD 480I

3. 720*480 31.50 60.00 27.027 SDTV 480P

4. 720*480 31.47 59.94 27.00 SDTV 480P

5. 1280*720 45.00 60.00 74.25 HDTV 720P

6. 1280*720 44.96 59.94 74.176 HDTV 720P

7. 1920*1080 33.75 60.00 74.25 HDTV 1080I

8. 1920*1080 33.72 59.94 74.176 HDTV 1080I

9. 1920*1080 67.50 60.00 148.50 HDTV 1080P

10. 1920*1080 67.432 59.94 148.352 HDTV 1080P

11. 1920*1080 27.00 24.00 74.25 HDTV 1080P

12. 1920*1080 26.97 23.94 74.176 HDTV 1080P

13. 1920*1080 33.75 30.00 74.25 HDTV 1080P

14. 1920*1080 33.71 29.97 74.176 HDTV 1080P

5.1.2. HDMI Input 1 (PC/DTV)

No. Resolution H-freq(kHz) V-freq.(kHz) Pixel clock(MHz) Proposed

HDMI-PC DDC

1 640*350 31.468 70.09 25.17 EGA Х

2 720*400 31.469 70.08 28.32 DOS O

3 640*480 31.469 59.94 25.17 VESA(VGA) O

4 800*600 37.879 60.31 40.00 VESA(SVGA) O

5 1024*768 48.363 60.00 65.00 VESA(XGA) O

6 1152*864 54.348 60.053 80.00 VESA O

7 1280*1024 63.981 60.020 108.00 VESA (SXGA) O

8 1360*768 47.712 60.015 85.50 VESA (WXGA) O

9 1920*1080 67.5 60 148.5

HDMI-DTV

1 720*480 31.47 60 27.027 SDTV 480P

2 720*480 31.47 59.94 27.00 SDTV 480P

3 1280*720 45.00 60.00 74.25 HDTV 720P

4 1280*720 44.96 59.94 74.176 HDTV 720P

5 1920*1080 33.75 60.00 74.25 HDTV 1080I

6 1920*1080 33.72 59.94 74.176 HDTV 1080I

7 1920*1080 67.500 60 148.50 HDTV 1080P

8 1920*1080 67.432 59.939 148.352 HDTV 1080P

9 1920*1080 27.000 24.000 74.25 HDTV 1080P

10 1920*1080 26.97 23.976 74.176 HDTV 1080P

11 1920*1080 33.75 30.000 74.25 HDTV 1080P

12 1920*1080 33.71 29.97 74.176 HDTV 1080P

WUXGA(Reduced Blanking)

O

Only for training and service purposes

- 7 -

5.2. 3D Mode

5.2.1. RF Input

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1 1920*1080 45.00 60 74.25 HDTV 1080I Side by Side, Top & Bottom

2 1280*720 45.00 60 74.25 HDTV 720P Side by Side, Top & Bottom

5.2.2. HDMI Input

5.2.2.1. HDMI 1.3 - DTV (3D supported mode manually)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1 1280*720p 45.00 60.00 74.25 Side by Side , Top & Bottom,

2 1920*1080i 33.75 60.00 74.25 Side by Side, Top & Bottom

3 1920*1080p 67.50 60.00 148.50 Side by Side , Top & Bottom

4 1920*1080p 27.00 24.000 74.25 Side by Side , Top & Bottom

5 1920*1080p 33.75 30.000 74.25 Side by Side, Top & Bottom

Single Frame Sequential

Checkerboard, Single Frame Sequential Row Interleaving, Column Interleaving

Checkerboard

5.2.2.2. HDMI 1.3 - DTV (3D supported mode manually)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1 1280*720p 89.91 / 90.00 59.94 / 60.00 148.35 / 148.50 Mandatory Frame Packing,

2 1280*720p 44.96 / 45.00 59.94 / 60.00 74.18 / 74.25 Mandatory Top & Bottom

3 1920*1080i 33.72 / 33.75 59.94 / 60.00 74.18 / 74.25 Mandatory Side by Side (Half)

4 1920*1080p 43.94 / 54.00 23.97 / 24.00 148.35 / 148.50 Mandatory Frame Packing,

5 1920*1080p 26.97 / 27.00 23.97 / 24.00 74.18 / 74.25 Mandatory Top & Bottom

6 1280*720p 44.96 / 45.00 59.94 / 60.00 74.18 / 74.25 Primary Side by Side (Half)

7 1920*1080i 67.432 / 67.50 59.94 / 60.00 148.35 / 148.50 Primary Frame Packing

8 1920*1080p 67.43 / 67.50 59.94 / 60.00 148.35 / 148.50 Primary Top & Bottom

9 1920*1080p 26.97 / 27.00 23.97 / 24.00 74.18 / 74.25 Primary Side by Side (Half)

10 1920*1080p 67.432 / 67.50 29.976 / 30.00 148.35 / 148.50 Primary Frame Packing,

11 1920*1080p 33.716 / 33.75 29.976 / 30.00 74.18 / 74.25 Primary Top & Bottom

12 1920*1080i 33.72 / 33.75 59.94 / 60.00 74.18 / 74.25 Secondary Top & Bottom

13 1920*1080p 67.43 / 67.50 59.94 / 60.00 148.35 / 148.50 Secondary Side by Side (Half)

14 1920*1080p 33.716 / 33.75 29.976 / 30.00 74.18 / 74.25 Secondary Side by Side (Half)

15 720*480p 62.938 / 63.00 59.94 / 60.00 54.00 / 54.054 Secondary (16:9) Frame Packing,

16 720*480p 31.469 / 31.50 59.94 / 60.00 27.00 / 27.027 Secondary (16:9) Top & Bottom

17 720*480p 31.469 / 31.50 59.94 / 60.00 27.00 / 27.027 Secondary (16:9) Side by Side (Half)

Only for training and service purposes

- 8 -

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

18 720*480p 62.938 / 63.00 59.94 / 60.00 54.00 / 54.054 Secondary (4:3) Frame Packing,

19 720*480p 31.469 / 31.50 59.94 / 60.00 27.00 / 27.027 Secondary (4:3) Top & Bottom

20 720*480p 31.469 / 31.50 59.94 / 60.00 27.00 / 27.027 Secondary (4:3) Side by Side (Half)

21 640*480p 62.938 / 63.00 59.94 / 60.00 50.35 / 50.40 Secondary Frame Packing,

22 640*480p 31.469 / 31.50 59.94 / 60.00 25.175 / 25.20 Secondary Top & Bottom

23 640*480p 31.469 / 31.50 59.94 / 60.00 25.175 / 25.20 Secondary Side by Side (Half)

24 1280*720p 89.91 / 90.00 59.94 / 60.00 148.35 / 148.50 Line Alternative

25 1280*720p 44.96 / 45.00 59.94 / 60.00 148.35 / 148.50 Side by Side (Full)

26 1920*1080i 67.432 / 67.50 59.94 / 60.00 148.35 / 148.50 Field Alternative

27 1920*1080i 33.72 / 33.75 59.94 / 60.00 148.35 / 148.50 Side by Side (Full)

28 1920*1080p 43.94 / 54.00 23.97 / 24.000 148.35 / 148.50 Line Alternative

29 1920*1080p 26.97 / 27.00 23.97 / 24.000 148.35 / 148.50 Side by Side (Full)

30 1920*1080p 67.432 / 67.50 29.976 / 30.00 148.35 / 148.50 Line Alternative

31 1920*1080p 33.716 / 33.75 29.976 / 30.00 148.35 / 148.50 Side by Side (Full)

32 720*480p 62.938 / 63.00 59.94 / 60.00 54.00 / 54.054 16:9 Line Alternative

33 720*480p 31.469 / 31.50 59.94 / 60.00 54.00 / 54.054 16:9 Side by Side (Full)

34 720*480p 62.938 / 63.00 59.94 / 60.00 54.00 / 54.054 4:3 Line Alternative

35 720*480p 31.469 / 31.50 59.94 / 60.00 54.00 / 54.054 4:3 Side by Side (Full)

36 640*480p 62.938 / 63.00 59.94 / 60.00 50.35 / 50.40 Line Alternative

37 640*480p 31.469 / 31.50 59.94 / 60.00 50.35 / 50.40 Side by Side (Full)

5.2.3. HDMI-PC Input (3D supported mode manually)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1 1024*768 48.363 60.004 65.000 Side by Side, Top & Bottom

2 1360*768 47.712 60.015 85.500 Side by Side, Top & Bottom

3 1920*1080 67.50 60.00 148.50 Side by Side, Top & Bottom

Checkerboard, Single Frame Sequential Row Interleaving, Column Interleaving

5.2.4. USB Input

5.2.4.1. USB Input (3D supported mode automatically)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1 1920*1080 33.75 30.000 74.25 HDTV 1080p Side by Side, Top & Bottom,

5.2.4.2. USB Input (3D supported mode manually)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1 1920*1080 33.75 30.000 74.25 HDTV 1080p Side by Side, Top & Bottom

Checkerboard, MPO (Photo)

Checkerboard, Single Frame Sequential, Row Interleaving, Column Interleaving (Photo : Side by Side, Top & Bottom)

Only for training and service purposes

- 9 -

5.2.5. DLNA Input

R

L

R

L

5.2.5.1. DLNA Input (3D supported mode automatically)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1 1920*1080 33.75 30.000 74.25 HDTV 1080p Side by Side, Top & Bottom,

Checkerboard, MPO (Photo)

5.2.5.2. DLNA Input (3D supported mode manually)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1 1920*1080 33.75 30.000 74.25 HDTV 1080p Side by Side, Top & Bottom

Checkerboard, Single Frame Sequential, Row Interleaving, Column Interleaving (Photo : Side by Side, Top & Bottom)

5.2.6. Component Input

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1 1280*720 44.96 59.94 74.176 HDTV 720P Side by Side, Top & Bottom

2 1920*1080 33.75 60.00 74.25 HDTV 1080I Side by Side, Top & Bottom

3 1920*1080 33.72 59.94 74.176 HDTV 1080I Side by Side, Top & Bottom

4 1920*1080 67.500 60 148.50 HDTV 1080P Side by Side, Top & Bottom

5 1920*1080 67.432 59.94 148.352 HDTV 1080P Side by Side, Top & Bottom

6 1920*1080 27.000 24.000 74.25 HDTV 1080P Side by Side, Top & Bottom

7 1920*1080 26.97 23.976 74.176 HDTV 1080P Side by Side, Top & Bottom

8 1920*1080 33.75 30.000 74.25 HDTV 1080P Side by Side, Top & Bottom

9 1920*1080 33.71 29.97 74.176 HDTV 1080P Side by Side, Top & Bottom

● Remark: 3D Input mode

No Side by Side Top & Bottom Checkerboard Single Frame

1

Sequential

- 10 -

Only for training and service purposes

Frame Packing Line Interleaving Column Inter-

leaving

ADJUSTMENT INSTRUCTION

1. Application

This spec. sheet applies to EA34D Chassis applied LED TV all models manufactured in TV factory

2. Specification

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation

transformer will help protect test instrument. (2) Adjustment must be done in the correct order. (3) The adjustment must be performed in the circumstance of

25 ±5 ºC of temperature and 65±10% of relative humidity if

there is no specific designation (4) The input voltage of the receiver must keep 100~240V,

50/60Hz (5) The receiver must be operated for about 5 minutes prior to

the adjustment when module is in the circumstance of over

15

ºC

In case of keeping module is in the circumstance of 0°C, it

should be placed in the circumstance of above 15°C for 2

hours In case of keeping module is in the circumstance of below

-20°C, it should be placed in the circumstance of above

15°C for 3 hours.

※ Caution When still image is displayed for a period of 20 minutes or longer (especially where W/B scale is strong. Digital pattern 13ch and/or Cross hatch pattern 09ch), there can some afterimage in the black level area

3. Adjustment items

3.1. Main PCBA Adjustments

(1) ADC adjustment: Component 480i, 1080p (2) EDID downloads for HDMI

4. MAIN PCBA Adjustments

4.1. ADC Calibration

- An ADC cali bra tion is not necessary because MA IN SoC (LGExxxx) is already calibrated from IC Maker

- If it needs to adjust manually, refer to appendix.

4.2. MAC Address, ESN Key and Widevine Key download

4.2.1. Equipment & Condition

1) Play file: keydownload.exe

4.2.2. Communication Port connection

1) Key Write: Com 1,2,3,4 and 115200 (Baudrate)

2) Barcode: Com 1,2,3,4 and 9600 (Baudrate)

4.2.3. Download process

1) Select the download items.

2) Mode check: Online Only

3) Check the test process

- US, C anada m odels : DETEC T -> M AC_ WR IT E -> WIDEVINE_WRITE

- Korea, Mexico m odels: DET ECT -> MAC_WRI TE -> WIDEVINE_WRITE

4) Play : START

5) Check of result: Ready, Test, OK or NG

6) Printer out (MAC Address Label)

4.2.4. Communication Port connection

1) Connect: PCBA Jig -> RS-232C Port == PC -> RS-232C

Port

※ Remark

- Above adjustment items can be also performed in Final Assembly if needed. Adjustment items in both PCBA and final assembly tages can be checked by using the INSTART Menu -> 1.ADJUST CHECK

3.2. Final assembly adjustment

(1) White Balance adjustment (2) RS-232C functionality check (3) Factory Option setting per destination (4) Shipment mode setting (In-Stop) (5) GND and HI-POT test

3.3. Appendix

(1) Tool option menu, USB Download (S/W Update, Option and

Service only) (2) Manual adjustment for ADC calibration and White balance. (3) Shipment conditions, Channel pre-set

Only for training and service purposes

4.2.5. Download

1) US, Canada models (13Y LCD TV + MAC + Widevine + ESN Key + DTCP Key + HDCP1.4 and HDCP2.0)

4.2.6. Inspection

- In INSTART menu, check these keys.

- 11 -

4.3. LAN port Inspection (Ping Test)

4.3.1. Equipment setting

1) Play the LAN Port Test PROGRAM.

2) Input IP set up for an inspection to Test Program.

- IP number: 12.12.2.2

4.3.2. LAN PORT inspection (PING TEST)

1) Play the LAN Port Test Program.

2) Connect each other LAN Port Jack.

3) Play Test (F9) button and confirm OK Message.

4) Remove LAN CABLE

4.4.4. EDID DATA(PCM)

(1)DTS # HDMI 1(C/S : E8 36) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

-------------------------------------------------------------------------------- 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 | 01 17 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E8

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

-------------------------------------------------------------------------------- 0 | 02 03 34 F1 48 90 22 20 05 04 03 02 01 29 3d 06 10 | C0 15 07 50 09 57 07 78 03 0C 00 10 00 B8 2D 20 20 | C0 0E 01 4F 00 FE 08 10 06 10 18 10 28 10 38 10 30 | E3 05 03 01 02 3A 80 18 71 38 2D 40 58 2C 45 00 40 | 40 84 63 00 00 1E 01 1D 80 18 71 1C 16 20 58 2C 50 | 25 00 40 84 63 00 00 9E 01 1D 00 72 51 D0 1E 20 60 | 6E 28 55 00 40 84 63 00 00 1E 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 36

4.4. EDID Download

4.4.1 Overview

▪ It is a VESA regulation. A PC or a MNT will display an

optimal resolution through information sharing without any necessity of user input. It is a realization of “Plug and Play”.

4.4.2 Equipment

▪ Since embedded EDID data is used, EDID download JIG,

HDMI cable and D-sub cable are not need.

▪ Adjust remocon

4.4.3 Download method

1) Press Adj. key on the Adj. R/C,

2) Select EDID D/L menu.

3) By pressing Enter key, EDID download will begin

4) If Download is successful, OK is display, but If Download is failure, NG is displayed.

5) If Download is failure, Re-try downloads.

# HDMI 2(C/S : E8 26) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

-------------------------------------------------------------------------------- 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 | 01 17 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E8

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 02 03 34 F1 48 90 22 20 05 04 03 02 01 29 3D 06 10 | C0 15 07 50 09 57 07 78 03 0C 00 20 00 B8 2D 20 20 | C0 0E 01 4F 00 FE 08 10 06 10 18 10 28 10 38 10 30 | E3 05 03 01 02 3A 80 18 71 38 2D 40 58 2C 45 00 40 | 40 84 63 00 00 1E 01 1D 80 18 71 1C 16 20 58 2C 50 | 25 00 40 84 63 00 00 9E 01 1D 00 72 51 D0 1E 20 60 | 6E 28 55 00 40 84 63 00 00 1E 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 26

※ Caution) When EDID Download, must remove RGB/HDMI

Cable.

Only for training and service purposes

- 12 -

# HDMI 3(C/S : E8 16) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 | 01 17 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E8

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 02 03 34 F1 48 90 22 20 05 04 03 02 01 29 3D 06 10 | C0 15 07 50 09 57 07 78 03 0C 00 30 00 B8 2D 20 20 | C0 0E 01 4F 00 FE 08 10 06 10 18 10 28 10 38 10 30 | E3 05 03 01 02 3A 80 18 71 38 2D 40 58 2C 45 00 40 | 40 84 63 00 00 1E 01 1D 80 18 71 1C 16 20 58 2C 50 | 25 00 40 84 63 00 00 9E 01 1D 00 72 51 D0 1E 20 60 | 6E 28 55 00 40 84 63 00 00 1E 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 16

# HDMI 4(C/S : E8 06) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 | 01 17 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E8

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 02 03 34 F1 48 90 22 20 05 04 03 02 01 29 3D 06 10 | C0 15 07 50 09 57 07 78 03 0C 00 40 00 B8 2D 20 20 | C0 0E 01 4F 00 FE 08 10 06 10 18 10 28 10 38 10 30 | E3 05 03 01 02 3A 80 18 71 38 2D 40 58 2C 45 00 40 | 40 84 63 00 00 1E 01 1D 80 18 71 1C 16 20 58 2C 50 | 25 00 40 84 63 00 00 9E 01 1D 00 72 51 D0 1E 20 60 | 6E 28 55 00 40 84 63 00 00 1E 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06

(2)AC3 # HDMI 1(C/S : E8 3F) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 | 01 17 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E8

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 02 03 31 f1 48 90 22 20 05 04 03 02 01 26 15 07 10 | 50 09 57 07 78 03 0c 00 10 00 b8 2d 20 c0 0e 01 20 | 4f 00 fe 08 10 06 10 18 10 28 10 38 10 e3 05 03 30 | 01 02 3a 80 18 71 38 2d 40 58 2c 45 00 40 84 63 40 | 00 00 1e 01 1d 80 18 71 1c 16 20 58 2c 25 00 40 50 | 84 63 00 00 9e 01 1d 00 72 51 d0 1e 20 6e 28 55 60 | 00 40 84 63 00 00 1e 00 00 00 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3f

# HDMI 2(C/S : E8 2F) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 | 01 17 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E8

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 02 03 31 f1 48 90 22 20 05 04 03 02 01 26 15 07 10 | 50 09 57 07 78 03 0c 00 20 00 b8 2d 20 c0 0e 01 20 | 4f 00 fe 08 10 06 10 18 10 28 10 38 10 e3 05 03 30 | 01 02 3a 80 18 71 38 2d 40 58 2c 45 00 40 84 63 40 | 00 00 1e 01 1d 80 18 71 1c 16 20 58 2c 25 00 40 50 | 84 63 00 00 9e 01 1d 00 72 51 d0 1e 20 6e 28 55 60 | 00 40 84 63 00 00 1e 00 00 00 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2f

Only for training and service purposes

- 13 -

# HDMI 3(C/S : E8 1F) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 | 01 17 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E8

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 02 03 31 f1 48 90 22 20 05 04 03 02 01 26 15 07 10 | 50 09 57 07 78 03 0c 00 30 00 b8 2d 20 c0 0e 01 20 | 4f 00 fe 08 10 06 10 18 10 28 10 38 10 e3 05 03 30 | 01 02 3a 80 18 71 38 2d 40 58 2c 45 00 40 84 63 40 | 00 00 1e 01 1d 80 18 71 1c 16 20 58 2c 25 00 40 50 | 84 63 00 00 9e 01 1d 00 72 51 d0 1e 20 6e 28 55 60 | 00 40 84 63 00 00 1e 00 00 00 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1f

# HDMI 4(C/S : E8 0F) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 | 01 17 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E8

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 02 03 31 f1 48 90 22 20 05 04 03 02 01 26 15 07 10 | 50 09 57 07 78 03 0c 00 40 00 b8 2d 20 c0 0e 01 20 | 4f 00 fe 08 10 06 10 18 10 28 10 38 10 e3 05 03 30 | 01 02 3a 80 18 71 38 2d 40 58 2c 45 00 40 84 63 40 | 00 00 1e 01 1d 80 18 71 1c 16 20 58 2c 25 00 40 50 | 84 63 00 00 9e 01 1d 00 72 51 d0 1e 20 6e 28 55 60 | 00 40 84 63 00 00 1e 00 00 00 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0f

(3)PCM # HDMI 1(C/S : E8 B1) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 | 01 17 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E8

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 02 03 2e f1 48 90 22 20 05 04 03 02 01 23 09 57 10 | 07 78 03 0c 00 10 00 b8 2d 20 c0 0e 01 4f 00 fe 20 | 08 10 06 10 18 10 28 10 38 10 e3 05 03 01 02 3a 30 | 80 18 71 38 2d 40 58 2c 45 00 40 84 63 00 00 1e 40 | 01 1d 80 18 71 1c 16 20 58 2c 25 00 40 84 63 00 50 | 00 9e 01 1d 00 72 51 d0 1e 20 6e 28 55 00 40 84 60 | 63 00 00 1e 00 00 00 00 00 00 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b1

# HDMI 2(C/S : E8 A1) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 | 01 17 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E8

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 02 03 2e f1 48 90 22 20 05 04 03 02 01 23 09 57 10 | 07 78 03 0c 00 20 00 b8 2d 20 c0 0e 01 4f 00 fe 20 | 08 10 06 10 18 10 28 10 38 10 e3 05 03 01 02 3a 30 | 80 18 71 38 2d 40 58 2c 45 00 40 84 63 00 00 1e 40 | 01 1d 80 18 71 1c 16 20 58 2c 25 00 40 84 63 00 50 | 00 9e 01 1d 00 72 51 d0 1e 20 6e 28 55 00 40 84 60 | 63 00 00 1e 00 00 00 00 00 00 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 A1

Only for training and service purposes

- 14 -

# HDMI 3(C/S : E8 91) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 | 01 17 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E8

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 02 03 2e f1 48 90 22 20 05 04 03 02 01 23 09 57 10 | 07 78 03 0c 00 30 00 b8 2d 20 c0 0e 01 4f 00 fe 20 | 08 10 06 10 18 10 28 10 38 10 e3 05 03 01 02 3a 30 | 80 18 71 38 2d 40 58 2c 45 00 40 84 63 00 00 1e 40 | 01 1d 80 18 71 1c 16 20 58 2c 25 00 40 84 63 00 50 | 00 9e 01 1d 00 72 51 d0 1e 20 6e 28 55 00 40 84 60 | 63 00 00 1e 00 00 00 00 00 00 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 91

# HDMI 4(C/S : E8 81) EDID Block 0, Bytes 0-127 [00H-7FH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 10 | 01 17 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E8

5. Final Assembly Adjustment

5.1. White Balance Adjustment

5.1.1. Overview

5.1.1.1. W/B adj. Objective & How-it-works (1) Objective: To reduce each Panel’s W/B deviation (2) How-it-works: When R/G/B gain in the OSD is at 192, it

means the panel is at its Full Dynamic Range. In order to prevent saturation of Full Dynamic range and data, one of R/G/B is fixed at 192, and the other two is lowered to find the desired value.

(3) Adj. condition: normal temperature

- Surrounding Temperature: 25±5 °C

- Warm-up time: About 5 Min

- Surrounding Humidity: 20% ~ 80%

- Before White balance adjustment, Keep power on status, don’t power off

5.1.1.2. Adj. condition and cautionary items

(1) Lighting condition in surrounding area surrounding lighting

should be lower 10 lux. Try to isolate adj. area into dark surrounding.

(2) Probe location: Color Analyzer (CA-210) probe should be

within 10cm and perpendicular of the module surface (80°~ 100°) (3) Aging time

- After Aging Start, Keep the Power ON sta tus during 5

Minutes.

- In case of LCD, Back-light on should be checked using no

signal or Full-white pattern.

5.1.2. Equipment

(1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12 / LED:

CH14 / OLED : CH : 17) (2) Adj. Computer (During auto adj., RS-232C protocol is

needed) (3) Adjust Remocon (4) Vi deo Signal Generat or MS PG-925F 720p/ 204-Gray

(Model: 217, Pattern: 49) ※ Color Analyzer Matrix should be calibrated using CS-1000

EDID Block 1, Bytes 128-255 [80H-FFH]

0 1 2 3 4 5 6 7 8 9 A B C D E F

--------------------------------------------------------------------------------- 0 | 02 03 2e f1 48 90 22 20 05 04 03 02 01 23 09 57 10 | 07 78 03 0c 00 40 00 b8 2d 20 c0 0e 01 4f 00 fe 20 | 08 10 06 10 18 10 28 10 38 10 e3 05 03 01 02 3a 30 | 80 18 71 38 2d 40 58 2c 45 00 40 84 63 00 00 1e 40 | 01 1d 80 18 71 1c 16 20 58 2c 25 00 40 84 63 00 50 | 00 9e 01 1d 00 72 51 d0 1e 20 6e 28 55 00 40 84 60 | 63 00 00 1e 00 00 00 00 00 00 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 81

Only for training and service purposes

- 15 -

5.1.3. Equipment connection

Color Analyzer

Probe

RS-232C

※

Signal Source

※If TV internal pattern is used, not needed

Pattern Generator

5.1.4. Adjustment Command (Protocol)

(1) RS-232C Command used during auto-adj.

RS-232C COMMAND

CMD DATA ID

Wb 00 00 Begin White Balance adj.

Wb 00 ff End White Balance adj.

(internal pattern disappears )

(2) Adjustment Map

Adj. item Command

(lower caseASCII)

CMD1 CMD2 MIN MAX

Cool R Gain j g 00 C0

G Gain j h 00 C0

B Gain j i 00 C0

Medium R Gain j a 00 C0

G Gain j b 00 C0

B Gain j c 00 C0

Warm R Gain j d 00 C0

G Gain j e 00 C0

B Gain j f 00 C0

Explanation

Data Range (Hex.)

Computer

RS-232C

5.1.5.2. OLED White balance table (1) Cool Mode

- Purpose : Espec ially B-g ain fix adj ust leads to the

luminance enhancement. Adjust the color temperature to reduce the deviation of the module color temperature.

- Prin ciple : To adju st the white bala nce witho ut the

saturation, Adjust the B gain more than 192 ( If R gain or G gain is more than 255 , G gain can adjust less than 192 ) and change the others ( R/G Gain ).

- Adjustment mode : mode – Cool

(2) Medium / Warm Mode

- Purpose : Adjust the color temperature to reduce the

deviation of the module color temperature

- Prin ciple : To adju st the white bala nce witho ut the

saturation, Fix the B ga in to 192 (de fau lt data) and decrease the others

- Adjustment mode : mode – Medium

(3) Warm

- Purpose : Adjust the color temperature to reduce the

deviation of the module color temperature.

- Prin ciple : To adju st the white bala nce witho ut the

saturation, Fix the W gain to 192 (default data) and decrease the others.

- Adjustment mode : mode – Warm

(4) THX(Warm)

- Purpose : Adjust the color temperature to reduce the

deviation of the module color temperature.

- Prin ciple : To adju st the white bala nce witho ut the

saturation, Fix the W gain to 192 (default data) and decrease the others.

- Adjustment mode : mode – Warm

- Auto White balance 4 point

- Adjust 100 IRE White Balance

- Adjust Gamam 2.2 each IRE (60, 40, 20). Using max

luminance

- Complete 4 point gamma, W/B.

5.1.5. Adjustment method

5.1.5.1. Auto WB calibration (1) Set TV in ADJ mode using P-ONLY key (or POWER ON

key)

(2) Place optical probe on the center of the display

- It need to check probe condition of zero calibration before

adjustment. (3) Connect RS-232C Cable (4) Select mode in ADJ Program and begin a adjustment. (5) When WB adjustment is completed with OK message,

check adjustment status of pre-set mode (Cool, Medium,

Warm) (6) Remove probe and RS-232C cable.

▪ W/B Adj. must begin as start command “wb 00 00” , and

finish as end command “wb 00 ff”, and Adj. offset if need

Only for training and service purposes

- 16 -

Picture is H 1/3, V 1/3 fixed Center Window size Outer Black Picture do not need change Contrast / Brightness Center Level can change Contrast / Bright Window pattern of Center 0~255 level

5.1.6. Reference (White Balance Adj. coordinate and color temperature)

(1) Luminance: 204 Gray, 80IRE (2) Standard color coordinate and temperature using CS-1000

(over 26 inch)

5.1.7. Reference (White Balance Adj. coordinate and color temperature)

▪ Luminance: 204 Gray ▪ Standard color coordinate and temperature using CS-1000

(over 26 inch)

Mode

Cool 0.271 0.270 13,000K 0.0000

Medium 0.285 0.293 9,300K 0.0000

Warm 0.313 0.329 6,500K 0.0000

▪ S ta ndard colo r coo rd ina te an d tem pe rat ur e usi ng

CA-210(CH-14)

Mode

Cool 0.271±0.002 0.270±0.002 13,000K 0.0000

Medium 0.285±0.002 0.293±0.002 9,300K 0.0000

Warm 0.313±0.002 0.329±0.002 6,500K 0.0000

▪ S ta ndard colo r coo rd ina te an d tem pe rat ur e usi ng

CA-210(CH-14) – by aging time

Coordinate

X Y

Coordinate

X Y

Temp △uv

5.3. Magic Motion remote controller Check

5.3.1. Test equipment

▪ RF-remote controller for check, IR-KEY-CODE remote

controller.

▪ Check AA battery before test. A recommendation is that a

tester change battery every lots.

5.3.2. Test

(1) Make pairing with TV set by pressing “Start key(Wheel

key)” on RCU. (2) Check a cursor on screen by pressing ‘Wheel key” of RCU (3) Stop paring with TV set by pressing “Back+ Home” key of

RCU

5.3.3. Applied models

Chassis Model Name Magic RF receiver

EA34D 55EA8800-UA Built-in

55EA9800-UA

5.4. Wi-Fi MAC Address Check

5.4.1. Using RS232 Command

Command Set ACK

Transmission [A][l][][Set ID][][20][Cr] [O][K][x] or [N][G]

5.4.2. Check the menu on in-start

5.2. Tool Option setting & Inspection per countries

5.2.1. Overview

(1) Tool option selection is only done for models in Non-USA

North America due to rating

(2) Applied model: EA34D Chassis applied to CANADA and

MEXICO

5.2.2. Country Group selection

(1) Press ADJ key on the Adj. R/C, and then select Country

Group Menu

(2) Depending on destination, select US, then on the lower

Country option, select US, CA, MX.

Selection is done using +, - KEY

5.2.3. Tool Option inspection

▪ Press Adj. key on the Adj. R/C, then select Tool option

Model Tool 1 Tool 2 Tool 3 Tool 4 Tool 5 Tool 6 Tool 7

55EA9800-UA 32791 21777 5085 61837 55446 1432 47147

※ Tool option can be reconstructed by Software

Only for training and service purposes

- 17 -

5.5. 3D pattern test (Only for 3D models)

5.5.1. Test equipment

(1) Pattern Generator MSHG-600 or MSPG-6100 (HDMI 1.4

support)

(2) Pattern: HDMI mode (model No. 872, pattern No. 83)

5.6. HDMI ARC Function Inspection

5.6.1. Test equipment

- Optic Receiver Speaker

- MSHG-600 (SW: 1220 ↑)

- HDMI Cable (for 1.4 version)

5.5.2. Test method

(1) Input 3D test signal as Fig.1.

(2) Press ‘OK” key as a 3D input OSD is shown. (3) Check pattern as Fig2 without 3D glasses. (3D mode

without 3D glasses)

Fig.2

5.6.2. Test method

(1) Insert the HDMI Cable to the HDMI ARC port from the

master equipment (HDMI1)

(2) Check the sound from the TV Set

(3) Check the Sound from the Speaker or using AV & Optic

TEST program (It’s connected to MSHG-600)

Fig.3

Only for training and service purposes

- 18 -

* Remark: Inspect in Power Only Mode and check SW version

in a master equipment

5.7. PIP/ W&R Function Inspection

(1) Objective : To check the connection between sub tuner and

PCBA, and their Function

(2) Test Method : This Inspection is available only Power-Only

Status.

1) Press exit key of the Adj. R/C and Press PIP key.

2) Check that the SUB TUNER pop up window on the TV Set.

3) Check that the normal operation (picture, sound) of DTV on the TV Set.

6.3. Audio Output Inspection

(1) I NPU T CH E CK – S KEY OF A DJU ST R E MO T E

CONTROLLER TO INSPECT SPEAKER

(2) When you click the first, the output volume of left & right

main speakers must be 50

(3) When you click the second, the output volume of left & right

main speakers must be 80.

(4) When you click the third, the output volume of left & right

main speakers must be 100.

5.8. Ship-out mode check (In-stop)

▪ After final inspection, press In-Stop key of the Adj. R/C and

check that the unit goes to Stand-by mode

6. AUDIO output check

6.1. Audio input condition

(1) RF input: Mono, 1KHz sine wave signal, 100% Modulation (2) CVBS, Component: 1KHz sine wave signal (0.4Vrms) (3) RGB PC: 1KHz sine wave signal (0.7Vrms)

6.2. Specification

No Item Min Typ Max Unit Remark

1 Audio

practical max Output, L/R (Distortion=10% max Output)

9.0

8.5

10.0

8.9

12.0

9.9WVrms

(1) Measurement

condition

- EQ/AVL/Clear Voice: Off

(2) Speaker (8Ω

Impedance)

(5) When you click the fourth, the output volume of left main

speaker must be 50.

(6) When you click the fifth, the output volume of right main

speaker must be 50.

(7) When you click the sixth, the output volume of left sub

speaker must be 100.

(8) When you click the seventh, the output volume of right sub

speaker must be 100.

Only for training and service purposes

- 19 -

(9) When yo u cli ck th e eig hth , the output volume of all

speakers (left & right main speaker and left & right sub speaker) must be 30.

7. Soft Touch Key Check

- Before you start a test, you must run a ‘Power Only Mode’. AFTER Touch SOFT TOUCH KEY OF SET, LOCAL KEY

CHECK DISPLAY WILL START

(1) Tab Test : Touch SOFT TOUCH KEY OF SET quickly

(2) Left Test : Touch SOFT TOUCH KEY OF SET to the left

side.

(3) Right Test : Touch SOFT TOUCH KEY OF SET to the right

side

8. EYE Q Green Inspection

(1) Turn on TV (2) Press EYE key of Adj. R/C

(3) Cover the Eye Q sensor on the front of the using your hand

and wait for 6 seconds

(4) Confirm that value is lower than 100 of the “Raw Data

(Sensor data, Back light )” If after 6 seconds, value is not lower than 100, replace Eye Q sensor

(5) Remove your hand from the Eye Q sensor and wait for 6

seconds

(4) Long Tab Test : Touch SOFT TOUCH KEY OF SET long.

- Don’t need to run a test with this sequence. For example, the

sequence such as ‘Right → Tab → Long Tab → Left’ is

allowed.

(6) Confirm that “ok” pop up. If change is not seen, replace

Eye Q sensor

Only for training and service purposes

- 20 -

9. GND and HI-POT Test

9.1. GND & HI-POT auto-check preparation

(1) Check the POWER CABLE and SIGNAL CABE insertion

condition

9.2. GND & HI-POT auto-check

(1) Pallet moves in the station. (POWER CORD / AV CORD is

tightly inserted) (2) Connect the AV JACK Tester. (3) Controller (GWS103-4) on. (4) GND Test (Auto)

- If Test is failed, Buzzer operates.

- If Test is passed, execute next process (Hi-pot test). (Remove A/V CORD from A/V JACK BOX) (5) HI-POT test (Auto)

- If Test is failed, Buzzer operates.

- If Test is passed, GOOD Lamp on and move to next process

automatically.

9.3. Checkpoint

(1) Test voltage

- GND: 1.5KV/min at 100mA

- SIGNAL: 3KV/min at 100mA (2) TEST time: 1 second (3) TEST POINT

- GND Test = POWER CORD GND and SIGNAL CABLE GND.

- Hi-pot Test = POWER CORD GND and LIVE & NEUTRAL. (4) LEAKAGE CURRENT: At 0.5mArms

10. USB S/W Download (optional, Service only)

(1) Put the USB Stick to the USB socket (2) Automatically detecting update file in USB Stick

- If your downloaded program version in USB Stick is lower than that of TV set, it didn’t work. Otherwise USB data is automatically detected.

(3) Show the message “Copying files from memory”

(4) Updating is staring

(5) Updating Completed, The TV will restart automatically

(6) If your TV is turned on, check your updated version and

Tool option.

* If downloading version is more high than your TV have, TV

can lost all channel data. In this case, you have to channel recover. If all channel data is cleared, you didn’t have a DTV/ ATV test on production line.

* After downloading, TOOL OPTION setting is needed again. (1) Push "IN-START" key in service remote controller. (2) Select "Tool Option 1" and Push “OK” button. (3) Punch in the number. (Each model has their number.)

Only for training and service purposes

- 21 -

11. Optional adjustments

11.1. Manual ADC Calibration

11.1.1. Equipment & Condition

(1) Adjustment Remocon (2) 801GF (802B, 802F, 802R) or MSPG925FA Pattern

Generator

- Resolution: 480i Com p1 (MSP G-925 FA: mode l-209 , pattern-65)

- Resol ution: 1080p Comp1 (MSPG- 925FA: model-225,

pattern-65)

- Resolution : 10 80p RGB (MSPG-92 5FA: model-225,

pattern-65)

- Pattern : Horizontal 100% Color Bar Pattern

- Pattern level: 0.7±0.1 Vp-p

11.1.2. Equipment & Condition

11.1.2.1. ADC 480i/1080p Comp (1) Check connected condition of Co mp ca bl e to the

equipment

(2) Give a 480i Mode, Horizontal 100% Color Bar Pattern to

Comp1. (MSPG-925FA → Model: 209, Pattern: 65)

(3) Change input mode as Component1 and picture mode as

“Standard”

(4) Press the In-start Key on the ADJ remote after at least 1

min of signal reception. Then, select 7.External ADC. And

Press OK or Right Button for going to sub menu. (5) Press OK in Comp 480i menu (6) Give a 1080p Mode, Horizontal 100% Color Bar Pattern to

Comp1. (MSPG-925FA → Model: 225, Pattern: 65)

(7) Press OK in Comp 1080p menu (8) If ADC Comp is successful, “ADC Component Success” is

displayed. If ADC calibration is failure, “ADC Component

Fail” is displayed. (10) If ADC calibration is failure, after rechecking ADC pattern

or condition, retry calibration

(11) If ADC calibration is failure, after recheck ADC pattern or

condition, retry calibration

11.2. Manual White balance Adjustment

11.2.1. Adj. condition and cautionary items

(1) Lighting condition in surrounding area surrounding lighting

should be lower 10 lux. Try to isolate adj. area into dark surrounding.

(2) Probe location: Color Analyzer (CA-210) probe should be

within 10cm and perpendicular of the module surface (80°~ 100°) (3) Aging time

- After Aging Sta rt, Keep the Power ON status during 5

Minutes.

- In case of LCD, Back-light on should be checked using no

signal or Full-white pattern

11.2.2. Equipment

(1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12 / LED:

CH14/ OLED : CH17) (2) Adj. Computer (During auto adj., RS-232C protocol is

needed) (3) Adjust Remocon (4) Vi deo Signal Generator MSPG-925F 720p/216- Gray

(Model: 217, Pattern: 78)

11.2.3. Adjustment

(1) Set TV in Adj. mode using POWER ON (2) Zero Calibrate the probe of Color Analyzer, then place it on

the center of LCD module within 10cm of the surface.

(3) Press ADJ key → EZ adjust using adj. R/C → 6. White-

Balance then press the cursor to the right (KEY►). When KEY(►) is pressed 216 Gray internal pattern will be

displayed.

(4) One of R Gain / G Gain / B Gain should be fixed at 192,

and the rest will be lowered to meet the desired value. (5) Adj. is performed in COOL, MEDIUM, WARM 3 modes of

color temperature.

▪ If internal pattern is not available, use RF input. In EZ Adj.

menu 6.White Balance, you can select one of 2 Test-pattern:

ON, OFF. Default is inner(ON). By selecting OFF, you can

adjust using RF signal in 216 Gray pattern.

Only for training and service purposes

- 22 -

EXPLODED VIEW

IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essenti al that these special safet y parts shoul d be replac ed with the same compo nents as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

700

710

900

914

400

521

522

570

121

913

912

911

571

540

LV2

530

LV1

580

610

120

600

CAM1

560

AT1

561

500

AV1

200

501

AG1

Only for training and service purposes

310

- 23 -

CA1

A22

A2

System Configuration

LGE Internal Use Only

Clock for LG1154D

MAIN Clock(24Mhz)

10pF

C100

10pF

C101

System Clock for Analog block(24Mhz)

PLL SET[1:0] : internal pull up "00" : CPU(1200Mhz),M0 / M1 DDR(792,792 Mhz) "01" : CPU(1056Mhz),M0 / M1 DDR(672,672 Mhz) "10" : CPU(1056Mhz),M0 / M1 DDR(792,792 Mhz) "11" : CPU( 960Mhz),M0 / M1 DDR(792,792 Mhz)

OPT

R100 33

R101 33

OPT

+3.3V_NORMAL

OPT

2

3

R150

X-TAL_1

GND_1

1

R108

X100

24MHz

4

GND_2

X-TAL_2

PLLSET1

PLLSET0

INSTANT boot MODE "1 : Instant boot "0 : normal

3.3K (internal pull down)

1M

INSTANT_BOOT

INSTANT_MODE0

Jtag I/F For Main

TP101

TP102

TP103

TP104

TP105

TP106

+3.3V_NORMAL

TP109

TP108

Model Option

HW_OPT_0 HW_OPT_1

HW_OPT_2

HW_OPT_3

HW_OPT_4

HW_OPT_5

HW_OPT_6

HW_OPT_7

HW_OPT_8

HW_OPT_9

HW_OPT_10

AREA option1

FRC option

Pannel Resol

OLED option

EPI PANEL version

reserved

CP BOX

T2 support

satellite support

AREA option2

EPI selection

C106 33pF 50V

+3.3V_NORMAL

TAIWAN

R110 10K

NON_TAIWAN

R109 10K

10K

R112

INTERNAL_FRC

10K

NO_FRC

R111

XIN_MAIN

XO_MAIN

FHD

R114 10K

UD

R113 10K

TRST_N0 TDI0 TDO0 TMS0 TCK0 SOC_RESET

OLED

R116 10K

NON_OLED

R115 10K

+3.3V_NORMAL

BOOT MODE "0 : EMMC "1 : TEST MODE

3.3K

R117

OPT

3.3K

R118

BOOT_MODE0

V13_MODULE

R120 10K

V12_MODULE

R119 10K

OP MODE[1:0] "00" : Normal Mode "01/10/11" : Internal Test mode

+3.3V_NORMAL

BOOT_MODE

OPT

CP_BOX

R126 10K

R122 10K

R124 10K

DVB_T2_TUNER

NON_CP_BOX

R125 10K

R121 10K

R123 10K

NON_DVB_T2_TUNER

R1EX24256BSAS0A

A0

A1

A2

VSS

OPT

R133 33

R134 33

OPT

AJ_JA

DVB_S_TUNER

R129 10K

R128 10K

NON_AJ_JA

R130 10K

R127 10K

NON_DVB_S_TUNER

NVRAM

EEPROM_RENESAS

IC102

1

2

A0’h

3

4

EPI

R131 10K

NON_EPI

R132 10K

OPM1

OPM0

VCC

8

WP

7

SCL

6

SDA

5

C103

0.1uF

MODEL_OPT_0

MODEL_OPT_2

MODEL_OPT_3

MODEL_OPT_4

MODEL_OPT_5

MODEL_OPT_6

MODEL_OPT_7

MODEL_OPT_8

MODEL_OPT_9

MODEL_OPT_10

+3.3V_TU

R135

3.3K

KR_PIP_NOT

1.5K

KR_PIP

R135-*1

+3.3V_NORMAL

Write Protection

- Low : Normal Operation

- High : Write Protection

R139 33

R140 33

Area1

FRCMODEL_OPT_1

Panel

OLED

Module

Reserved

CP BOX

T2 Tuner

S Tuner

Area2

EPI

+3.3V_TU

+3.3V_NORMAL

R137

3.3K

R138

3.3K

R136

3.3K

KR_PIP_NOT

1.5K

KR_PIP

R136-*1

HIGH

Taiwan

FRC(120Hz)

FHD

OLED

V13

Enable

Support

AJ_JA

Support

R141

3.3K

R142

EPHY_INT

TP100 TP107 TP110 TP111

+3.3V_NORMAL

3.3K

R143

3.3K

I2C_SCL5

I2C_SDA5

IRB_SPI_SS IRB_SPI_MOSI IRB_SPI_MISO IRB_SPI_CK

LOW

non Taiwan

No FRC(60Hz)

UD

NON OLED

V12

Default

Disable

Not Support

non AJ_JA

Not Support

I2C PULL UP

R145

3.3K

R144

3.3K

R164331/16W

R146

3.3K

M24256-BRMN6TP

E0

E1

E2

VSS

R147

3.3K

EEPROM_ST

IC102-*1

VCC

8

1

WC

2

7

SCL

3

6

SDA

4

5

XIN_MAIN

XO_MAIN

SOC_RESET

H13A_SCL H13A_SDA

TRST_N0

PLLSET1 PLLSET0

BOOT_MODE

5%

SOC_RX

SOC_TX M_REMOTE_RX M_REMOTE_TX

M_REMOTE_RTS M_REMOTE_CTS

IRB_SPI_SS IRB_SPI_MOSI IRB_SPI_MISO

IRB_SPI_CK

I2C_SCL1

I2C_SDA1 I2C_SCL_MICOM_SOC I2C_SDA_MICOM_SOC

I2C_SCL2_SOC I2C_SDA2_SOC

I2C_SCL4

I2C_SDA4

I2C_SCL5

I2C_SDA5

I2C_SCL6

I2C_SDA6

I2C_SDA_MICOM I2C_SCL_MICOM

I2C_SDA2 I2C_SCL2

R148

3.3K I2C_SDA1 I2C_SCL1 I2C_SDA_MICOM_SOC

I2C_SCL_MICOM_SOC I2C_SDA2_SOC

I2C_SCL2_SOC I2C_SDA4 I2C_SCL4

I2C_SDA5 I2C_SCL5

I2C_SDA6 I2C_SCL6

OPM1 OPM0

TMS0 TCK0 TDI0 TDO0

R152

R149 33

R151 33 R174 33

R10533

33

R106

R10233

33

R104

I2C for tuner

560

A26

XIN

B26

XOUT

B27

XTAL_BYPASS

AT37

H13DA_XTAL

AU16

PORES_N

AD34

OPM1

AD33

OPM0

AT26

H13DA_SCL

AU26

H13DA_SDA

AP9

TRST_N0

AN9

TMS0

AP11

TCK0

AN11

TDI0

AN10

TDO0

AM10

TRST_N1

AM9

TMS1

AM11

TCK1

AM12

TDI1

AL11

TDO1

AL9

PLLSET1

AL10

PLLSET0

AE34

BOOT_MODE

Y33

EXT_INTR3/GPIO70

W32

EXT_INTR2/GPIO69

W33

EXT_INTR1/GPIO68

W34

EXT_INTR0/GPIO67

AU12

UART0_RXD

AT12

UART0_TXD

AU13

UART1_RXD

AT13

UART1_TXD

AP12

UART1_RTS

AR12

UART1_CTS

AE35

SPI_CS0/GPIO36

AE36

SPI_DO0/GPIO38

AF36

SPI_DI0/GPIO39

AF35

SPI_SCLK0/GPIO37

AG34

SPI_CS1

AF33

SPI_DO1

AG33

SPI_DI1

AG32

SPI_SCLK1

AR15

SCL0/GPIO66

AP15

SDA0/GPIO65

AR16

SCL1/GPIO64

AP16

SDA1/GPIO79

AP17

SCL2/GPIO78

AR17

SDA2/GPIO77

AP6

SCL3

AR6

SDA3

AH32

SCL4

AJ33

SDA4

AH34

SCL5

AH33

SDA5

I2C_SDA_MICOM_SOC I2C_SCL_MICOM_SOC

I2C_SDA2_SOC

I2C_SCL2_SOC

+3.3V_NORMAL

CAM_CE1_N

CAM_CE2_N

CAM_CD1_N/GPIO76

F33

F34

D32

E32

/PCM_CE1

/PCM_CE2

CAM_CD1_N

CI

USB_CTL3

/USB_OCD3

/USB_OCD2

USB_CTL2

K35

K36

K37

L35

EB_CS3/GPIO93

EB_CS2/GPIO92

EB_CS1/GPIO91

EB_CS0/GPIO90

EB_WE_N

EB_BE_N1

EB_OE_N

H35

H36

J35

J36

H37

EB_WE_N/GPIO95

EB_WAIT/GPIO94

EB_OE_N/GPIO82

EB_BE_N1/GPIO81

EB_ADDR[0-14]

EB_BE_N0

EB_ADDR[13]

EB_ADDR[14]

EB_ADDR[12]

G37

G36

G35

F36

EB_BE_N0/GPIO80

EB_ADDR15/GPIO89

EB_ADDR14/GPIO88

EB_ADDR13/GPIO103

EB_ADDR12/GPIO102

EB_ADDR[8]

EB_ADDR[6]

EB_ADDR[7]

EB_ADDR[9]

EB_ADDR[11]

EB_ADDR[10]

F35

E36

E37

E35

D37

EB_ADDR9/GPIO99

EB_ADDR8/GPIO98

EB_ADDR7/GPIO97

EB_ADDR11/GPIO101

EB_ADDR10/GPIO100

EB_ADDR[4]

EB_ADDR[5]

EB_ADDR[3]

D36

D35

C36

C35

EB_ADDR6/GPIO96

EB_ADDR5/GPIO111

EB_ADDR4/GPIO110

EB_ADDR3/GPIO109

EB_ADDR[0]

EB_ADDR[1]

EB_ADDR[2]

EB_DATA[7]

B37

B36

B35

C32

EB_ADDR2/GPIO108

EB_ADDR1/GPIO107

EB_ADDR0/GPIO106

EB_DATA[0-7]

EB_DATA[5]

EB_DATA[6]

B33

A33

EB_DATA7/GPIO105

EB_DATA6/GPIO104

EB_DATA5/GPIO119

IC100

LG1154D_H13D

CAM_CD2_N/GPIO75

CAM_VS1_N/GPIO86

CAM_VS2_N/GPIO85

CAM_IREQ_N/GPIO73

CAM_RESET

CAM_INPACK/GPIO74

CAM_VCCEN_N/GPIO87

CAM_WAIT_N/GPIO84

CAM_REG_N/GPIO72

CAM_IOIS16_N/GPIO83

SC_CLK/GPIO130

SC_DETECT/GPIO133

SC_VCCEN/GPIO129

SC_VCC_SEL/GPIO128

SC_RST/GPIO131

SC_DATA/GPIO132

SD_CLK/GPIO125

SD_CMD/GPIO124

SD_CD_N/GPIO123

SD_WP_N/GPIO122

SD_DATA3/GPIO121

SD_DATA2/GPIO120

SD_DATA1/GPIO135

SD_DATA0/GPIO134

USB2_2_DP0

USB2_2_DM0

USB2_2_TXRTUNE

G32

G33

F32

G34

D33

H32

E33

D34

H33

T33

U33

T32

V32

V33

V34

A25

C25

B25

E25

D25

E24

D24

C24

L37

L36

K34

1%

200

CAM_CD2_N

R153

10K

PCM_RESET

CAM_IREQ_N

CAM_INPACK_N

CI

R154

10K

CAM_REG_N

CAM_WAIT_N

PCM_5V_CTL

R155

10K

CI

SMARTCARD_CLK/SD_EMMC_DATA[0]

SMARTCARD_DET/SD_EMMC_DATA[3]

interface

Only SMART CARD

SMARTCARD_DATA/SD_EMMC_CLK

SMARTCARD_VCC/SD_EMMC_CMD

SMARTCARD_RST/SD_EMMC_DATA[2]

SMARTCARD_PWR_SEL/SD_EMMC_DATA[1]

R157

USB2_HUB_IC_IN_DM

USB2_HUB_IC_IN_DP

EB_DATA[2]

EB_DATA[4]

EB_DATA[3]

EB_DATA[0]

EB_DATA[1]

C33

A34

B34

C34

A36

EB_DATA4/GPIO118

EB_DATA3/GPIO117

EB_DATA2/GPIO116

EB_DATA1/GPIO115

EB_DATA0/GPIO114

USB2_1_DP0

USB2_1_DM0

USB2_1_TXRTUNE

USB2_0_DP

M37

M36

K33

AU7

1%

200

R159

WIFI_DP

USB_DM2

USB_DP2

EMMC_DATA[0-7]

EMMC_CLK

EMMC_CMD

EMMC_RST

Y37

Y36

W35

EMMC_CLK

EMMC_CMD

EMMC_RESETN

USB2_0_DM

USB2_0_TXRTUNE

USB3_DP0

AT7

AP7

P37

WIFI_DM

R161 200 1%

USB3_DP

EMMC_DATA[5]

EMMC_DATA[7]

EMMC_DATA[6]

T36

W36

V35

EMMC_DATA7

EMMC_DATA6

EMMC_DATA5

USB3_DM0

USB3_RX0P

USB3_RX0M

P36

N36

N37

USB3_DM

USB3_RX0P

USB3_RX0M

EMMC_DATA[4]

EMMC_DATA[3]

EMMC_DATA[2]

V37

V36

U35

EMMC_DATA4

EMMC_DATA3

EMMC_DATA2

USB3_TX0P

USB3_TX0M

USB3_RESREF

R36

R37

N34

1%

200

R162

C105 0.1uF

C104 0.1uF

USB3_TX0M

USB3_TX0P

U36

EMMC_DATA1

USB3_REFPADCLKM

P33

EPHY_MDIO

EPHY_EN

EPHY_MDC

EPHY_REFCLK

EPHY_CRS_DV

EMMC_DATA[1]

EMMC_DATA[0]

U37

AU11

AU8

AT8

AR8

AR10

AT10

RMII_MDC

RMII_MDIO

RMII_CRS_DV

RMII_REF_CLK

NC_1

NC_2

NC_3

L32

L33

M31

AJ31

RMII_TXEN

NC_4

J32

EMMC_DATA0

USB3_REFPADCLKP

P32

AC-coupling CAP

Place near by LG1154D

EPHY_RXD1

EPHY_TXD0

EPHY_TXD1

AU10

AT11

AR11

RMII_TXD1

RMII_TXD0

RMII_RXD1

GPIO136

GPIO137

GPIO138

J33

K32

J34

EPHY_RXD0

RMII_RXD0

GPIO31 GPIO30 GPIO29 GPIO28 GPIO27 GPIO26 GPIO25

GPIO24 GPIO23/UART2_TX GPIO22/UART2_RX

GPIO21

GPIO20

GPIO19

GPIO18

GPIO17

GPIO16

GPIO15

GPIO14

GPIO13

GPIO12

GPIO11

GPIO10

GPIO9 GPIO8 GPIO7 GPIO6 GPIO5 GPIO4 GPIO3 GPIO2 GPIO1 GPIO0

DDCD0_CK DDCD0_DA

HPD0

PHY0_ARC_OUT_0

PHY0_RX0N_0 PHY0_RX0P_0 PHY0_RX1N_0 PHY0_RX1P_0 PHY0_RX2N_0 PHY0_RX2P_0 PHY0_RXCN_0 PHY0_RXCP_0

HUB_PORT_OVER0

HUB_VBUS_CTRL0

GPIO139

TP112

IR_B_RESET

AL34 AM33 AM32 AF30 AN34 AK34 AL33 AL32 AR9 AM5 AM6 AM7 AL6 AK7 AK6 AK5 AJ5 AJ6 AJ7 AH6 AG7 AG6 AG5 AF5 AH30 AG30 AN33 AK33 AE30 AD30 AN32 AK32

AC32 AC33 AB33

AE37 AC36 AC37 AB36 AB37 AA36 AA37 AD36 AD37

R32

R33

CAM_SLIDE_DET

/RST_PHY RF_SWITCH_CTL

UART2_TX UART2_RX AMP_RESET_N

INSTANT_BOOT

SC_DET AV1_CVBS_DET

COMP1_DET M_RFModule_RESET HP_DET FRC_RESET /TU_RESET1 /S2_RESET VCOM_DYN PMIC_RESET /RST_HUB FE_LNA_Ctrl2 /TU_RESET2 HDMI_S/W_RESET

FE_LNA_Ctrl1 HDMI_INT

R169 3.3K R170 3.3K

SPDIF_OUT_ARC

HDMI_RX0HDMI_RX0+ HDMI_RX1HDMI_RX1+ HDMI_RX2HDMI_RX2+ HDMI_CLK-

HDMI_CLK+

/USB_OCD1

USB_CTL1

UART2_RX

UART2_TX

local dimming

+3.3V_NORMAL

Debug

+3.3V_NORMAL

R165

3.3K

I2C port

+3.3V_NORMAL

SW100

JTP-1127WEM

4 3

DEBUG

P101

12507WS-04L

1

DEBUG

2

3

4

For ISP

12

DEBUG

5

R103

3.3K

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

BSD-NC4_H001-HD

2012-11-14

H13 D CHIP

LG1154A

LGE Internal Use Only

LG1154D

AVDD25

VDD25_LTX

VDDC10

GND JIG POINT

AVDD33_CVBS

VDD25_REF

VDD25_LTX

VDD25_AUD

VDD10_XTAL

AVDD33_XTAL

VSS25_REF

LG1154A

H13A_NON_BRAZIL

AVDD33

E11

F5 F6

F11

G5 H13 J13 P12 P13

R5

R6 N16 T13 T14

N10 N11 N12 N13

U5

N7

N8

N9 F14

M6

N6 M13 F15 F16 H15 J15 J16 K15 K16

R18

G7

G8

G9

H7 H12

J7 J12

K7 K12

L7 L12

M7 M12 T17 T18

M8 G10 G11 G12

V5

C3

D3

D4 D17

E4

F4

F7

F8

F9 F10 F12 F13 F17 F18

G4

G6 G13 G14 G15 G16 G17 G18

H4

H5

H6

H8

H9 H10 H11

JP202

JP203

LG1154AN_H13A

VDD33_1 VDD33_2 VDD33_3 VDD33_4 VDD33_5 VDD33_6 VDD33_7 VDD33_8 VDD33_9 VDD33_10 VDD33_11 VDD33_XTAL AVDD33_CVBS_1 AVDD33_CVBS_2

VDD25_CVBS_1 VDD25_CVBS_2 VDD25_VSB_1 VDD25_VSB_2 VDD25_REF VDD25_COMP_1 VDD25_COMP_2 VDD25_COMP_3 VDD25_APLL VDD25_AUD_1 VDD25_AUD_2 VDD25_AAD LTX_LVDD_1 LTX_LVDD_2 SDRAM_VDDQ_1 SDRAM_VDDQ_2 SDRAM_VDDQ_3 SDRAM_VDDQ_4 SDRAM_VDDQ_5

VDD10_XTAL VDDC10_1 VDDC10_2 VDDC10_3 VDDC10_4 VDDC10_5 VDDC10_6 VDDC10_7 VDDC10_8 VDDC10_9 VDDC10_10 VDDC10_11 VDDC10_12 VDDC10_13 AVDD10_CVBS AVDD10_VSB AVDD10_LLPLL DVDD10_APLL_1 DVDD10_APLL_2 LTX_VDD

VSS25_REF GND_1 GND_2 GND_3 GND_4 GND_5 GND_6 GND_7 GND_8 GND_9 GND_10 GND_11 GND_12 GND_13 GND_14 GND_15 GND_16 GND_17 GND_18 GND_19 GND_20 GND_21 GND_22 GND_23 GND_24 GND_25 GND_26 GND_27 GND_28 GND_29

JP204

JP205

IC101

GND_30 GND_31 GND_32 GND_33 GND_34 GND_35 GND_36 GND_37 GND_38 GND_39 GND_40 GND_41 GND_42 GND_43 GND_44 GND_45 GND_46 GND_47 GND_48 GND_49 GND_50 GND_51 GND_52 GND_53 GND_54 GND_55 GND_56 GND_57 GND_58 GND_59 GND_60 GND_61 GND_62 GND_63 GND_64 GND_65 GND_66 GND_67 GND_68 GND_69 GND_70 GND_71 GND_72 GND_73 GND_74 GND_75 GND_76 GND_77 GND_78 GND_79 GND_80 GND_81 GND_82 GND_83 GND_84 GND_85 GND_86 GND_87 GND_88 GND_89 GND_90 GND_91 GND_92 GND_93 GND_94 GND_95 GND_96 GND_97 GND_98

GND_99 GND_100 GND_101 GND_102 GND_103 GND_104 GND_105 GND_106 GND_107 GND_108 GND_109 GND_110 GND_111 GND_112 GND_113 GND_114 GND_115 GND_116

H14 J4 J5 J6 J8 J9 J10 J11 J14 K4 K5 K6 K8 K9 K10 K11 K13 K14 L1 L2 L3 L4 L5 L6 L8 L9 L10 L11 L13 L14 L15 L16 L17 L18 M1 M2 M3 M4 M5 M9 M10 M11 M14 M15 M16 N4 N5 N14 N15 N17 P4 P5 P6 P7 P8 P9 P10 P11 P14 P15 P16 R4 R7 R8 R9 R10 R11 R12 R13 R14 R15 R16 R17 T4 T7 T8 T9 T10 T11 T12 T15 T16 U4 U6 U18 V4 V16

SMD TOP for EMI

NON_LA8600

GASKET_8.0X6.0X8.5H

M200

MDS62110209

+3.3V_Bypass Cap

+3.3V_NORMAL

AVDD33

L209

BLM18PG121SN1D

(2)

4.7uFC241

C218 0.1uF

+2.5V_Bypass Cap

+2.5V_Normal

L220 BLM18PG121SN1D

+2.5V_Normal

L207 BLM18PG121SN1D

+1.0V_Bypass Cap

+1.0V_VDD

L211

BLM18PG121SN1D

+1.0V_VDD

L206

BLM18PG121SN1D

VDD25_LTX

4.7uFC275

+3.3V_NORMAL

4.7uFC242

4.7uFC211

4.7uFC216

VDD10_XTAL

VDDC10

AVDD33_XTAL

L216 BLM18PG121SN1D

AFE 3CH Power

AVDD25

4.7uFC270

C274 0.1uF

+2.5V_Normal

C223 0.1uF

4.7uFC239

C246 0.1uF

4.7uFC214

C251 0.1uF

(1)

4.7uFC255

C259 0.1uF

VDD25_REF

L225

BLM15BD121SN1

0.1uF

L226

BLM15BD121SN1

1005 size bead Bottom side of chip

C288

VSS25_REF

L200

BLM18PG121SN1D

+3.3V_Bypass Cap

+3.3V_NORMAL

BLM18PG121SN1D

+3.3V_NORMAL

VDD25_AUD

4.7uF

C200

C202

L203

AVDD33_CVBS

L222

BLM18PG121SN1D

4.7uFC279

C204 0.1uF

(2)

C283 0.1uF

VDD33

4.7uFC201

C203 0.1uF

+1.1V_Bypass Cap

+1.1V_VDD

4.7uFC297

4.7uFC351

+1.1V_VDD

L227

BLM18PG121SN1D

VDDC11_XTAL

4.7uFC298

+1.1V_VDD

VDD11_VTXPHY

L201

BLM18PG121SN1D

4.7uFC209

OPT

4.7uFC205

+1.5V_Bypass Cap

+1.5V_DDR

L230

L228

VDDC15_M0

22uF

C303

VDDC15_M1

22uFC299

C302

C307

0.1uF

C306

0.1uF

+1.5V_DDR

BLM18PG121SN1D

+2.5V_Bypass Cap

+2.5V_Normal

L234

BLM18PG121SN1D

0.1uF

C300 0.1uF

C301 0.1uF

C206 0.1uF

C308

C207 0.1uF

0.1uF

OPT

C208 0.1uF

VDDC15_M0

R200

R201

1K 1%

VDDC15_M1

R300

R301

1K 1%

VDD25_XTAL

4.7uFC364

OPT

VREF_M0_0

1K 1%

C296

VREF_M1_0

1K 1%

C304

C368 0.1uF

OPT

0.1uF

OPT

0.1uF

VDDC15_M0

R202

1K 1%

R203

1K 1%

VDDC15_M1

R302

1K 1%

R303

1K 1%

VREF_M0_1

OPT

0.1uF

C344

VREF_M1_1

OPT

0.1uF

C310

+2.5V_Normal

(1)

L238

BLM18PG121SN1D

VDD25_LVDS

4.7uFC378

+0.75V

+3.3V

+2.5V

+1.5V

(4)

C381 0.1uF

VREF_M1_1

VDDC11_XTAL

VDD25_XTAL

VDD33

VDD25_LVDS

VDD25_XTAL

VREF_M0_1

VREF_M1_0

VDDC15_M0

VDDC15_M1

VREF_M0_0

A24

P26 N26

M21 Y30

AA30

AE8

AF8 AK13 AK24 AK25

M22

M23 AK11 AK12 AF25 AF26

R31

AE23 AF23 AE14 AF14

N25 AD26

H10

H11

H12

H13

H14

H15

H16

H17

H18

H19

H20

H21

H22

H23

H24

H25

LG1154AN_H13A_ISDB-T (LG1154AN-IT)

M0_DDR_VREF1

A4

M0_DDR_VREF2

A2

M1_DDR_VREF1

Y1

M1_DDR_VREF2

XTAL_VDD XTAL_VDDP

VDD33_1 VDD33_2 VDD33_3 VDD33_4 VDD33_5 VDD33_6 VDD33_7 VDD33_8

AVDD33_USB_1 AVDD33_USB_2 AVDD33_BT_USB_1 AVDD33_BT_USB_2 AVDD33_HDMI_1 AVDD33_HDMI_2

SP_VQPS

VDD25_LVRX_1 VDD25_LVRX_2 VTXPHY_VDD25_1 VTXPHY_VDD25_2 VDD25_DR3PLL GPLL_AVDD25

VDD15_M0_1 VDD15_M0_2 VDD15_M0_3 VDD15_M0_4 VDD15_M0_5 VDD15_M0_6 VDD15_M0_7 VDD15_M0_8 VDD15_M0_9 VDD15_M0_10 VDD15_M0_11 VDD15_M0_12 VDD15_M0_13 VDD15_M0_14 VDD15_M0_15 VDD15_M0_16

H7

VDD15_M1_1

H8

VDD15_M1_2

J8

VDD15_M1_3

K8

VDD15_M1_4

L7

VDD15_M1_5

L8

VDD15_M1_6

M8

VDD15_M1_7

N7

VDD15_M1_8

N8

VDD15_M1_9

P8

VDD15_M1_10

R7

VDD15_M1_11

R8

VDD15_M1_12

T8

VDD15_M1_13

U8

VDD15_M1_14

V8

VDD15_M1_15

W8

VDD15_M1_16

P17

XIN_SUB

P18

XO_SUB

J17

VSB_AUX_XIN

N18

XTAL_BYPASS

D18

CLK_24M

M18

XTAL_SEL0

M17

XTAL_SEL1

E3

PORES_N

K3

OPM0

K2

OPM1

A8

H13A_SCL

B8

H13A_SDA

U13

CVBS_IN3

V14

CVBS_IN2

V15

CVBS_IN1

V13

CVBS_VCM

U15

BUF_OUT1

U14

BUF_OUT2

U7

REFT

V6

REFB

V7

ADC1_COM

U10

ADC2_COM

V12

ADC3_COM

T5

SC1_SID

T6

SC1_FB

U8

PB1_IN

V8

Y1_IN

V9

SOY1_IN

U9

PR1_IN

V10

PB2_IN

U11

Y2_IN

V11

SOY2_IN

U12

PR2_IN

IC100

LG1154D_H13D

VTXPHY_VDD11_1 VTXPHY_VDD11_2 VTXPHY_VDD11_3

H13A_BRAZIL

IC101-*1

AAD_ADC_SIF

AAD_ADC_SIFM

AUDA_VBG_EXT

AUDA_OUTL

AUDA_OUTR AUD_SCART_OUTL AUD_SCART_OUTR

AUAD_L_CH4_IN AUAD_R_CH4_IN AUAD_L_CH3_IN AUAD_R_CH3_IN AUAD_L_CH2_IN AUAD_R_CH2_IN AUAD_L_CH1_IN AUAD_R_CH1_IN

AUAD_R_REF AUAD_M_REF AUAD_L_REF

AUAD_REF_PO

ANTCON

RFAGC IFAGC

ADC_I_INCOM

ADC_I_INP

ADC_I_INN

GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7 GPIO8

GPIO9 GPIO10 GPIO11 GPIO12 GPIO13 GPIO14 GPIO15

VDDC11_1 VDDC11_2 VDDC11_3 VDDC11_4 VDDC11_5 VDDC11_6 VDDC11_7 VDDC11_8

VDDC11_9 VDDC11_10 VDDC11_11 VDDC11_12 VDDC11_13 VDDC11_14 VDDC11_15 VDDC11_16 VDDC11_17 VDDC11_18 VDDC11_19 VDDC11_20 VDDC11_21 VDDC11_22 VDDC11_23 VDDC11_24 VDDC11_25 VDDC11_26 VDDC11_27 VDDC11_28 VDDC11_29 VDDC11_30 VDDC11_31 VDDC11_32 VDDC11_33 VDDC11_34 VDDC11_35

AVDD11_DR3PLL

AVDD11_DCO GPLL_VDD11

H18 H17

P2 N1 N2 N3 P1

P3 R1 R2 T1 U2 U3 V2 V3 U1 T3 T2 R3

K17 K18 J18

U16 U17 V17

F3 F2 F1 G3 G2 G1 H3 H2 H1 J3 E18 E17 H16 J2 J1 K1

N21 N22 N23 P15 P16 P17 P18 R15 T15 T22 T23 T24 U15 U22 U23 U24 V15 V22 V23 V24 W22 W23 W24 AB15 AB24 AC15 AC24 AD15 AD16 AD17 AD18 AD21 AD22 AD23 AD24

AB14 AC14 AD14

P25 AA15 AC26

+1.1V_VDD

VDD11_VTXPHY

VDDC11_XTAL

+1.1V_VDD

+1.1V

A27

B5

C5 C26 C27

D5 D26

E5

E6

E7

E8 E22 E23 E26

F7

F8 F22 F23 F24 F25 F26 F27 F31

G7

G8

G9 G10 G11 G12 G13 G14 G15 G16 G17 G18 G19 G20 G21 G22 G23 G24 G25 G26 G27 G28 G29 G30 G31

H9 H26 H27 H28 H29 H30 H31

J7 J30 J31

K7 K30 K31 L30 L31

M7 M12 M13 M14 M15 M16 M17 M18 M19 M20 M24 M25 M26 M30 M32 M33 M34 N12 N13 N14 N15 N16 N17 N18 N19 N20 N24 N30 N31 N32 N33

P7 P12 P13 P14 P19 P20 P21 P22 P23 P24 P30 P31 R12 R13 R14 R16 R17 R18 R19 R20 R21 R22 R23 R24 R25 R26 R30 R34

T7 T12 T13 T14 T16 T17 T18 T19 T20 T21 T25 T26 T30 T31 T34

U7 U12 U13 U14 U16 U17 U18 U19 U20 U21 U25 U26 U30 U31

V7 V12 V13 V14 V16 V17 V18 V19 V20 V21 V25 V26 V30 V31

W5

W6

W7 W12 W13 W14 W15 W16 W17 W18 W19 W20 W21 W25 W26 W30 W31

Y3

Y4

LG1154D_H13D

GND_1 GND_2 GND_3 GND_4 GND_5 GND_6 GND_7 GND_8 GND_9 GND_10 GND_11 GND_12 GND_13 GND_14 GND_15 GND_16 GND_17 GND_18 GND_19 GND_20 GND_21 GND_22 GND_23 GND_24 GND_25 GND_26 GND_27 GND_28 GND_29 GND_30 GND_31 GND_32 GND_33 GND_34 GND_35 GND_36 GND_37 GND_38 GND_39 GND_40 GND_41 GND_42 GND_43 GND_44 GND_45 GND_46 GND_47 GND_48 GND_49 GND_50 GND_51 GND_52 GND_53 GND_54 GND_55 GND_56 GND_57 GND_58 GND_59 GND_60 GND_61 GND_62 GND_63 GND_64 GND_65 GND_66 GND_67 GND_68 GND_69 GND_70 GND_71 GND_72 GND_73 GND_74 GND_75 GND_76 GND_77 GND_78 GND_79 GND_80 GND_81 GND_82 GND_83 GND_84 GND_85 GND_86 GND_87 GND_88 GND_89 GND_90 GND_91 GND_92 GND_93 GND_94 GND_95 GND_96 GND_97 GND_98 GND_99 GND_100 GND_101 GND_102 GND_103 GND_104 GND_105 GND_106 GND_107 GND_108 GND_109 GND_110 GND_111 GND_112 GND_113 GND_114 GND_115 GND_116 GND_117 GND_118 GND_119 GND_120 GND_121 GND_122 GND_123 GND_124 GND_125 GND_126 GND_127 GND_128 GND_129 GND_130 GND_131 GND_132 GND_133 GND_134 GND_135 GND_136 GND_137 GND_138 GND_139 GND_140 GND_141 GND_142 GND_143 GND_144 GND_145 GND_146 GND_147 GND_148 GND_149 GND_150 GND_151 GND_152 GND_153 GND_154 GND_155 GND_156 GND_157 GND_158 GND_159 GND_160 GND_161 GND_162 GND_163 GND_164 GND_165 GND_166 GND_167 GND_168 GND_169 GND_170 GND_171 GND_172 GND_173 GND_174 GND_175 GND_176 GND_177 GND_178 GND_179 GND_180 GND_181 GND_182 GND_183 GND_184

IC100

GND_185 GND_186 GND_187 GND_188 GND_189 GND_190 GND_191 GND_192 GND_193 GND_194 GND_195 GND_196 GND_197 GND_198 GND_199 GND_200 GND_201 GND_202 GND_203 GND_204 GND_205 GND_206 GND_207 GND_208 GND_209 GND_210 GND_211 GND_212 GND_213 GND_214 GND_215 GND_216 GND_217 GND_218 GND_219 GND_220 GND_221 GND_222 GND_223 GND_224 GND_225 GND_226 GND_227 GND_228 GND_229 GND_230 GND_231 GND_232 GND_233 GND_234 GND_235 GND_236 GND_237 GND_238 GND_239 GND_240 GND_241 GND_242 GND_243 GND_244 GND_245 GND_246 GND_247 GND_248 GND_249 GND_250 GND_251 GND_252 GND_253 GND_254 GND_255 GND_256 GND_257 GND_258 GND_259 GND_260 GND_261 GND_262 GND_263 GND_264 GND_265 GND_266 GND_267 GND_268 GND_269 GND_270 GND_271 GND_272 GND_273 GND_274 GND_275 GND_276 GND_277 GND_278 GND_279 GND_280 GND_281 GND_282 GND_283 GND_284 GND_285 GND_286 GND_287 GND_288 GND_289 GND_290 GND_291 GND_292 GND_293 GND_294 GND_295 GND_296 GND_297 GND_298 GND_299 GND_300 GND_301 GND_302 GND_303 GND_304 GND_305 GND_306 GND_307 GND_308 GND_309 GND_310 GND_311 GND_312 GND_313 GND_314 GND_315 GND_316 GND_317 GND_318 GND_319 GND_320 GND_321 GND_322 GND_323 GND_324 GND_325 GND_326 GND_327 GND_328 GND_329 GND_330 GND_331 GND_332 GND_333 GND_334 GND_335 GND_336 GND_337 GND_338 GND_339 GND_340 GND_341 GND_342 GND_343 GND_344 GND_345 GND_346 GND_347 GND_348 GND_349 GND_350 GND_351 GND_352 GND_353 GND_354 GND_355 GND_356 GND_357 GND_358 GND_359 GND_360 GND_361 GND_362 GND_363 GND_364 GND_365 GND_366 GND_367 GND_368

Y5

Y8 Y12 Y13 Y14 Y15 Y16 Y17 Y18 Y19 Y20 Y21 Y22 Y23 Y24 Y25 Y26 Y31 Y35 AA8 AA12 AA13 AA14 AA16 AA17 AA18 AA19 AA20 AA21 AA22 AA23 AA24 AA25 AA26 AA31 AB6 AB8 AB12 AB13 AB16 AB17 AB18 AB19 AB20 AB21 AB22 AB23 AB25 AB26 AB30 AB31 AC8 AC12 AC13 AC16 AC17 AC18 AC19 AC20 AC21 AC22 AC23 AC25 AC30 AC31 AD8 AD12 AD13 AD19 AD20 AD25 AD31 AE12 AE13 AE15 AE16 AE17 AE18 AE19 AE20 AE21 AE22 AE24 AE25 AE26 AE31 AF12 AF13 AF15 AF16 AF17 AF18 AF19 AF20 AF21 AF22 AF24 AF31 AG8 AG31 AH8 AH31 AJ8 AJ30 AK8 AK9 AK10 AK14 AK15 AK16 AK17 AK18 AK19 AK20 AK21 AK22 AK23 AK26 AK27 AK28 AK29 AK30 AK31 AL8 AL12 AL13 AL14 AL15 AL16 AL17 AL18 AL19 AL20 AL21 AL22 AL23 AL24 AL25 AL26 AL27 AL28 AL29 AL30 AL31 AM8 AM13 AM14 AM15 AM16 AM17 AM18 AM19 AM20 AM21 AM22 AM23 AM24 AM25 AM26 AM27 AM28 AM29 AM30 AM31 AN6 AN12 AN13 AN15 AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

11/05/31

BSD-NC4_H002-HD

2012-12-24

MAIN POWER

Place JACK Side

LGE Internal Use Only

AV1_CVBS_IN

SC_CVBS_IN

SC_CVBS_IN_SOY

COMP1_Pb

COMP1_Pr

SCART_Lout

SCART_Rout

HP_LOUT_MAIN

HP_ROUT_MAIN

TU_CVBS

SC_FB

SC_ID

NON_EU R422-*1

COMP1_Y

5.5V

D404

0

SCART_FB_DIRECT

SC_B SC_G

SC_R

D403

D401

5.5V

Near Place Scart AMP

C6006

1uF 25V

C6001

SC_L_IN

SC_R_IN

COMP1/AV1/DVI_L_IN

COMP1/AV1/DVI_R_IN

+12V

R430

R445

L408

C405 150pF 50V

C408 150pF 50V

EU

C402 150pF 50V

OPT

SCART_FB_DIRECT

R423 100

10K

EU

R435

R422 75

10pF

C473

C472

50V

OPT

D406

5.5V

EU

10K

1uF25V

R60 06

EU

10K R6005

EU

R408

100K

R403

100K

EU

C403

2.2uF 10V

EU

R404

100K

R409

100K

R6450

100

C400

0.01uF

22K

R6451

C401

0.01uF

22K

L409

OPT

C430

EU

C474

2.2uF

100

10pF

50V

10V

1uH

C410 150pF

1uH

C462 150pF

EU

R436

2.7K

10pF

EU

50V

OPT

10pF

C431

C470

50V

SCART_AMP_R_FB

SCART_AMP_L_FB

EU

C406

+3.3V_NORMAL

R4641K1/16W

1%

R465

390

1/16W

1%

DAC_START_PULLDOWN

R466821/16W

R410 75 1%

R411 75

EU

1%

NON_EU

R436-*1

0

75

EU

75

1%

R416

R414

R412

10pF

1%

50V

SCART_Lout_SOC

SCART_Rout_SOC

AUDA_OUTL

AUDA_OUTR

C404

0.01uF 50V

EU

75

R413

75

1%

R415

1%

75 1%

R417

CLK_54M_VTT

FOR EMI

R418 27K

R419 27K

R420 27K

R421 27K

MAIN Clock(24Mhz)

C426

C427

Place SOC Side

R434

C424 0.047uF

100

R433

C425 0.047uF

100

SC_CVBS_IN_SOY

R432

C423 0.047uF

100

R424

C417 0.047uF

33

R425

C418 0.047uF

33

C428 1000pF

R427

C419 0.047uF

33

R428

C420 0.047uF

33

R429

C421 0.047uF

33

C429 1000pF C422 0.047uF

33

R431

AUDIO IN

1%

SCART_FB_BUFFER

SC_FB

C432 4.7uF

R437 10K 1%

C433 4.7uF

R438 10K 1%

C434 4.7uF

R439 10K 1%

C435 4.7uF

R440 10K 1%

R401 470

1/16W 5%

R4061K

SCART_FB_BUFFER

B

1/16W

1%

Clock for H13A

10pF

+3.3V_NORMAL

R446

4.7K

GND_1

2

3

X-TAL_2

AV1_CVBS_IN_SOC

SC_CVBS_IN_SOC

TU_CVBS_SOC

SC_FB_SOC

SC_ID_SOC

COMP1_PB_IN_SOC COMP1_Y_IN_SOC

COMP1_Y_IN_SOC_SOY

COMP1_PR_IN_SOC

COMP2_PB_IN_SOC COMP2_Y_IN_SOC COMP2_Y_IN_SOC_SOY

COMP2_PR_IN_SOC

SC_FB_BUF

C

MMBT3904(NXP)

Q400

SCART_FB_BUFFER

E

X-TAL_1

1

X400

24MHz

4

GND_2

AUAD_L_CH3_IN

AUAD_R_CH3_IN

AUAD_L_CH2_IN

AUAD_R_CH2_IN

1M

R441

Tuner IF Filter

COMP1_PB_IN_SOC

COMP1_Y_IN_SOC

COMP1_Y_IN_SOC_SOY

COMP1_PR_IN_SOC COMP2_PB_IN_SOC

COMP2_Y_IN_SOC

COMP2_Y_IN_SOC_SOY

COMP2_PR_IN_SOC

ADC_I_INN

ADC_I_INP

BLM18PG121SN1D

HP_LOUT_AMP

XIN_SUB

XOUT_SUB

XIN_SUB

XOUT_SUB

XTAL_SEL[0] XTAL_SEL[1]

SOC_RESET

OPM[0] OPM[1]

H13A_SCL

H13A_SDA

AV1_CVBS_IN_SOC

SC_CVBS_IN_SOC

TU_CVBS_SOC

DTV/MNT_V_OUT_SOC

Placed as close as possible to SOC

REFT REFB

R447 68 R448 68

R449 68

SC_ID_SOC SC_FB_SOC

+3.3V_NORMAL

DTV/MNT_V_OUT

To ADC

HP_OUT L400

HP_OUT C407

0.22uF 10V

R450

C439

OPT

100pF 50V

C440 0.047uF C441 0.047uF C442 0.047uF

MM1756DURE

VCC

6

PS

5

OUT

4

NON_TU_BR/TW

R443

51

NON_TU_W_BR/TW

NON_TU_BR/TW

R444

51

HP_LOUT

C443 0.047uF

68

IC400

Place at JACK SIDE

OP MODE Setting & Select XTAL Input

OP MODE[0:1] : SW[2:1] 00 => Normal Operaiton Mode /T32 Debug Mode 01 => Internal Test Purpose 10 => Internal Test Purpose 11 => Internal Test Purpose

XTAL SEL[1:0] : SW[4:3] 00 => Xtal Input 01 => CLK 24M from H13D 10 => XTAL Bypass from H13D

IC101

LG1154AN_H13A

P17

XIN_SUB

IN

1

GND

2

BIAS

3

TU_W_BR/TW

R443-*1

220

0.01uF

BLM18PG121SN1D

HP_ROUT_AMP

P18 J17

N18 D18 M18 M17

E3

K3 K2

A8 B8

U13 V14 V15 V13

U15 U14

U7 V6

V7 U10 V12

T5

T6

U8

V8

V9

U9 V10 U11 V11 U12

EU

TU_W_BR/TW

C437

L406

C438

HP_OUT

L401

XO_SUB VSB_AUX_XIN

XTAL_BYPASS CLK_24M XTAL_SEL0 XTAL_SEL1

PORES_N

OPM0 OPM1

H13A_SCL H13A_SDA

CVBS_IN3 CVBS_IN2 CVBS_IN1 CVBS_VCM

BUF_OUT1 BUF_OUT2

REFT REFB ADC1_COM ADC2_COM ADC3_COM SC1_SID SC1_FB PB1_IN Y1_IN SOY1_IN PR1_IN PB2_IN Y2_IN SOY2_IN PR2_IN

EU

C412

0.1uF

DTV/MNT_V_OUT_SOC

EU

4.7uF

C413

R444-*1

220

OPT

C414

0.1uF

EU

TU_W_BR/TW

HP_OUT C409

0.22uF 10V

C436-*1 100pF

IF_N

IF_P

HP_ROUT

R453 330

C436 22pF

Placed as close as possible to IC100

H13A_NON_BRAZIL

AAD_ADC_SIF

AAD_ADC_SIFM

AUDA_VBG_EXT

AUDA_OUTL

AUDA_OUTR AUD_SCART_OUTL AUD_SCART_OUTR

AUAD_L_CH4_IN AUAD_R_CH4_IN AUAD_L_CH3_IN AUAD_R_CH3_IN AUAD_L_CH2_IN AUAD_R_CH2_IN AUAD_L_CH1_IN AUAD_R_CH1_IN

AUAD_R_REF AUAD_M_REF AUAD_L_REF

AUAD_REF_PO

ANTCON

RFAGC IFAGC

ADC_I_INCOM

ADC_I_INP

ADC_I_INN

GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7 GPIO8

GPIO9 GPIO10 GPIO11 GPIO12 GPIO13 GPIO14 GPIO15

Placed as close as possible to IC4300

+3.3V_NORMAL

10K

OPT

R481

R482

R483

OPT 1uF

25V

R479100 R480100

HW_OPT_0 HW_OPT_1

HW_OPT_3 HW_OPT_4 HW_OPT_5

HW_OPT_7 HW_OPT_8 HW_OPT_9

SC_FB_BUF

OPT

R484

R426

22K

EU

ADC_I_INP ADC_I_INN

HW_OPT_2

HW_OPT_6

HW_OPT_10

MHL_ON_OFF

1%

R45 5

51K

R45 647K 1 %

R45421/10W

5%

C448

OPT

4.7uF 10V

H18

C450 0.1uF

H17

C451 0.1uF

C453 2.2uF

P2 N1 N2 N3 P1

P3 R1 R2 T1 U2 U3 V2 V3 U1 T3 T2 R3

K17 K18 J18

U16

C454 0.1uF

U17 V17

F3 F2 F1 G3 G2 G1 H3 H2 H1 J3 E18 E17 H16 J2 J1 K1

AUAD_REF_PO

AUAD_L_REF

AUAD_R_REF

AUAD_M_REF

100

R459

100

R460

100

R461

100

R462

10uFC452

AUDA_OUTL AUDA_OUTR

EU

AUAD_L_CH3_IN AUAD_R_CH3_IN

AUAD_L_CH2_IN

AUAD_R_CH2_IN

AUAD_R_REF

AUAD_M_REF AUAD_L_REF

AUAD_REF_PO

C447

AFE 3CH REF Setting

Placed as close as possible to IC4300

C444

0.1uF

C445

0.1uF

DIMMING

PWM_DIM2

PWM_DIM

C446

0.1uF

R490

R489

REFT

Must be used

REFB

100

OPM[0]

OPM[1] XTAL_SEL[0] XTAL_SEL[1]

TUNER_SIF

C457

1000pF

OPT

R442

22K

EU

C458 0.01uF

C460 0.01uF

Close to IC4300

NON_TU_W_BR/TW/CO

R487

0

C459

0.1uF

TU_W_BR/TW/CO

R487-*1

10K

+2.5V_Normal

C455

10uF

1% R45 7 51K

C4494.7uF

1%

C456

R45 8

4.7uF

47K

10V

PWM1

PWM2

SCART_Lout_SOC

SCART_Rout_SOC

IF_AGC

L407

LG1154AN_H13A

L/DIM0_VS

L/DIM0_SCLK L/DIM0_MOSI

IC101

INTR_GBB

INTR_AFE3CH

INTR_AGPIO

AUD_FS20CLK AUD_FS21CLK AUD_FS23CLK AUD_FS24CLK AUD_FS25CLK

AUDCLK_OUT_SUB

AUD_HDMI_MCLK

AUD_DAC1_LRCK

AUD_DAC1_SCK AUD_DAC1_LRCH AUD_DAC0_LRCK

AUD_DAC0_SCK AUD_DAC0_LRCH

AUD_ADC_LRCK

AUD_ADC_SCK

AUD_ADC_LRCH

BB_SCL

BB_SDA BB_TP_CLK BB_TP_ERR BB_TP_SOP BB_TP_VAL

BB_TP_DATA7 BB_TP_DATA6 BB_TP_DATA5 BB_TP_DATA4 BB_TP_DATA3 BB_TP_DATA2 BB_TP_DATA1 BB_TP_DATA0

CLK_F54M CVBS_GC2 CVBS_GC1 CVBS_GC0

CVBS_UP CVBS_DN

FS00CLK

AUDCLK_OUT

DAC_START DAC_DATA4 DAC_DATA3 DAC_DATA2 DAC_DATA1 DAC_DATA0

AAD_GC4 AAD_GC3 AAD_GC2 AAD_GC1 AAD_GC0

AAD_DATA9 AAD_DATA8 AAD_DATA7 AAD_DATA6 AAD_DATA5 AAD_DATA4 AAD_DATA3 AAD_DATA2 AAD_DATA1 AAD_DATA0

AAD_DATAEN

ADCO_OUT_CLK

HSR_AP0 HSR_AM0 HSR_BP0 HSR_BM0 HSR_CP0

HSR_CM0 HSR_CLKP0 HSR_CLKM0

HSR_DP0

HSR_DM0

HSR_EP0

HSR_EM0

R402 33 R405 33 R400 33

DPM

H13A_NON_BRAZIL

E1 E2 D1

A6 B6 A5 B5 A4 C4

C18

A2 B2 B1 C2 C1 D2 B4 A3 B3

A7 B7 E8 D8 C8 E7 D7 C7 E6 D6 C6 E5 D5 C5

CLK_54M_VTT

1/16W1%

B10 C9 B9 A9 D9 E9

Close to LG1154A

B11

R492 330

A11

R407 330

D11 C11 E10 D10 C10 A10

R451 330

D13 C13 E12 D12 C12

C17 E16 D16 C16 E15 D15 C15 E14 D14 C14 E13

B18

A12 B12 A13 B13 A14 B14 A15 B15 A16 B16 A17 B17

PWM1 PWM2

BPL_IN

EO_SOC

GST_SOC

MCLK_SOC GCLK_SOC

R467 82

DPM

AT16 AU17 AT17

AT24 AU24 AT23 AU23 AT22

AU36

AT20 AU20 AT19 AU19 AT18 AU18 AU22 AT21 AU21

AT25 AU25 AP23 AR23 AP22 AR22 AP21 AR21 AP20 AR20 AP19 AR19 AP18 AR18

AU28 AR24 AU27 AT27 AP24 AR25

AU29

DAC_START_PULLDOWN

AT29

AP27 AR27 AP26 AR26 AP25 AT28

AR30 AP29 AR29 AP28 AR28

AP35 AR35 AP34 AR34 AP33 AR33 AP32 AR32 AP31 AR31 AP30

AT36

AT30 AU30 AT31 AU31 AT32 AU32 AT33 AU33 AT34 AU34 AT35 AU35

AT14 AT15 AU15

NC

AR14 AP14 AN14 AP13

LG1154DLG1154A

INTR_GBB INTR_AFE3CH INTR_AGPIO

AUD_FS20CLK AUD_FS21CLK AUD_FS23CLK AUD_FS24CLK AUD_FS25CLK

AUD_HDMI_MCLK

AUD_DAC1_LRCK AUD_DAC1_SCK AUD_DAC1_LRCH AUD_DAC0_LRCK AUD_DAC0_SCK AUD_DAC0_LRCH AUD_ADC_LRCK AUD_ADC_SCK AUD_ADC_LRCH

BB_SCL BB_SDA BB_TPI_CLK BB_TPI_ERR BB_TPI_SOP BB_TPI_VAL BB_TPI_DATA7 BB_TPI_DATA6 BB_TPI_DATA5 BB_TPI_DATA4 BB_TPI_DATA3 BB_TPI_DATA2 BB_TPI_DATA1 BB_TPI_DATA0

CLK_54M CVBS_GC2 CVBS_GC1 CVBS_GC0 CVBS_UP CVBS_DN

FS00CLK H13A_AUDCLK_OUT

DAC_START DAC_DATA4 DAC_DATA3 DAC_DATA2 DAC_DATA1 DAC_DATA0

AAD_GC4 AAD_GC3 AAD_GC2 AAD_GC1 AAD_GC0

AAD_DATA9 AAD_DATA8 AAD_DATA7 AAD_DATA6 AAD_DATA5 AAD_DATA4 AAD_DATA3 AAD_DATA2 AAD_DATA1 AAD_DATA0 AAD_DATAEN

ADCO_OUT_CLK

HSR_AP HSR_AM HSR_BP HSR_BM HSR_CP HSR_CM HSR_CLKP HSR_CLKM HSR_DP HSR_DM HSR_EP HSR_EM

AUD_HPDRV_LRCH AUD_HPDRV_LRCK AUD_HPDRV_SCK

AC7

FRC_LR_O_SYNC_FLAG

AN5

L_VSOUT_LD DIM0_SCLK DIM0_MOSI DIM1_SCLK DIM1_MOSI

AF6

PWM0

AF7

PWM1

AD7

PWM2

AE6

PWM_IN

AP5

EPI_EO

AN8

EPI_VST

AP8

EPI_DPM

AR7

EPI_MCLK

AN7

EPI_GCLK

IC100

LG1154D_H13D

STPI0_CLK/GPIO47 STPI0_SOP/GPIO46 STPI0_VAL/GPIO45 STPI0_ERR/GPIO44

STPI0_DATA/GPIO43

STPI1_CLK/GPIO42 STPI1_SOP/GPIO41 STPI1_VAL/GPIO40 STPI1_ERR/GPIO55

STPI1_DATA/GPIO54

TPIO_DATA0/GPIO58 TPIO_DATA1/GPIO59 TPIO_DATA2/GPIO60 TPIO_DATA3/GPIO61 TPIO_DATA4/GPIO62 TPIO_DATA5/GPIO63 TPIO_DATA6/GPIO48 TPIO_DATA7/GPIO49

DACSLRCH/GPIO127 PCMI3SCK/GPIO112

PCMI3LRCK/GPIO113

DACCLFCH/GPIO126

TP_DVB_CLK TP_DVB_SOP TP_DVB_VAL

TP_DVB_ERR TP_DVB_DATA0 TP_DVB_DATA1 TP_DVB_DATA2 TP_DVB_DATA3 TP_DVB_DATA4 TP_DVB_DATA5 TP_DVB_DATA6 TP_DVB_DATA7

TPI_CLK TPI_SOP TPI_VAL

TPI_ERR TPI_DATA0 TPI_DATA1 TPI_DATA2 TPI_DATA3 TPI_DATA4 TPI_DATA5 TPI_DATA6 TPI_DATA7

TPIO_CLK/GPIO53 TPIO_SOP/GPIO52 TPIO_VAL/GPIO51 TPIO_ERR/GPIO50

AUDCLK_OUT

DACLRCH

DACSCK

DACLRCK

PCMI3LRCH

IEC958OUT

DACSUBMCLK DACSUBLRCH

DACSUBSCK

DACSUBLRCK

TEST1 TEST2

TX0N TX0P TX1N TX1P TX2N TX2P TX3N TX3P TX4N TX4P TX5N TX5P TX6N TX6P TX7N TX7P TX8N TX8P TX9N

TX9P TX10N TX10P TX11N TX11P TX12N TX12P

TX13N TX13P TX14N TX14P TX15N TX15P TX16N TX16P TX17N TX17P TX18N TX18P TX19N TX19P TX20N TX20P TX21N TX21P TX22N TX22P TX23N TX23P

TX_LOCKN

AK35 AK36 AK37 AJ35 AJ36 AH35 AH37 AH36 AG35 AG36

AM36 AL36 AL35 AL37 AM35 AN36 AN37 AN35 AP37 AP36 AR37 AR36

A28 B29 B28 C28 B32 C31 B31 A31 C30 A30 B30 C29

D30 D31 F30 E31 E30 F29 E29 F28 E28 D28 E27 D27

AD5 AD6 Y6 Y7 AC6 AC5 AA6 AB7 AB5 AU14 AA32 AA34 AA33 AB34 AE32 AE33

AT6 AU6 AT5 AU5 AT4 AU4 AU3 AU2 AT2 AT1 AR4 AR3 AP1 AP2 AP4 AP3 AN4 AN3 AM4 AM3 AL4 AL3 AK1 AK2 AK4 AK3

AJ4 AJ3 AH4 AH3 AG4 AG3 AF1 AF2 AF4 AF3 AE4 AE3 AD4 AD3 AC4 AC3 AB1 AB2 AB4 AB3 AA4 AA3

AR5

FE_DEMOD2_TS_CLK FE_DEMOD2_TS_SYNC FE_DEMOD2_TS_VAL FE_DEMOD2_TS_ERROR FE_DEMOD2_TS_DATA FE_DEMOD3_TS_CLK FE_DEMOD3_TS_SYNC FE_DEMOD3_TS_VAL FE_DEMOD3_TS_ERROR FE_DEMOD3_TS_DATA

FE_DEMOD1_TS_CLK FE_DEMOD1_TS_SYNC FE_DEMOD1_TS_VAL FE_DEMOD1_TS_ERROR

FE_DEMOD1_TS_DATA[0] FE_DEMOD1_TS_DATA[1] FE_DEMOD1_TS_DATA[2] FE_DEMOD1_TS_DATA[3] FE_DEMOD1_TS_DATA[4] FE_DEMOD1_TS_DATA[5] FE_DEMOD1_TS_DATA[6] FE_DEMOD1_TS_DATA[7]

TPI_CLK TPI_SOP TPI_VAL TPI_ERR

TPI_DATA[0] TPI_DATA[1] TPI_DATA[2] TPI_DATA[3] TPI_DATA[4] TPI_DATA[5] TPI_DATA[6] TPI_DATA[7]

TPO_CLK TPO_SOP TPO_VAL

TPO_ERR TPO_DATA[0] TPO_DATA[1] TPO_DATA[2] TPO_DATA[3] TPO_DATA[4] TPO_DATA[5] TPO_DATA[6] TPO_DATA[7]

R495 100

R496 100

R497 100 R498 100

R49333 R49433

TXB4N/TX0N TXB4P/TX0P TXB3N/TX1N TXB3P/TX1P TXBCLKN/TX2N TXBCLKP/TX2P TXB2N/TX3N TXB2P/TX3P TXB1N/TX4N TXB1P/TX4P TXB0N/TX5N TXB0P/TX5P TXA4N/TX6N TXA4P/TX6P TXA3N/TX7N TXA3P/TX7P TXACLKN/TX8N TXACLKP/TX8P TXA2N/TX9N

TXA2P/TX9P TXA1N/TX10N TXA1P/TX10P TXA0N/TX11N

TXA0P/TX11P

TXB2N

TXB2P

TXB1N

TXB1P

TXB0N

TXB0P

TXA4N

TXA4P

TXACLKN

TXACLKP

TXA1N

TXA1P TXC4N

TXC4P TXC3N TXC3P

TXCCLKN TXCCLKP TXC2N TXC2P TXC1N TXC1P TXC0N TXC0P

TP402

C411 10pF 50V OPT

TPI_ERR

TPI_DATA[0-7]

TP400

+3.3V_NORMAL

H13 Ball Name

EPI Output TXD4N/TX12N TXD4P/TX12P

TXD3N/TX13N TXD3P/TX13P TXDCLKN/TX14N TXDCLKP/TX14P TXD2N/TX15N TXD2P/TX15P TXD1N/TX16N TXD1P/TX16P TXD0N/TX17N TXD0P/TX17P

FE_DEMOD1_TS_DATA[0-7]

TPO_ERR

TPO_DATA[0-7]

AUD_MASTER_CLK

AUD_LRCH

FRC_FLASH_WP

AUD_SCK

AUD_LRCK

SPDIF_OUT

EPI_LOCK6

I2S_I/F

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

BSD-NC4_H004-HD

2012-11-13

MAIN AUDIO/VIDEO

IC100

LGE Internal Use Only

LG1154D_H13D

M0_DDR_A[10] M0_DDR_A[11] M0_DDR_A[12] M0_DDR_A[13] M0_DDR_A[14] M0_DDR_A[15]

M0_DDR_BA[0] M0_DDR_BA[1] M0_DDR_BA[2]

M0_DDR_U_CLK

M0_DDR_U_CLKN

M0_DDR_D_CLK

M0_DDR_D_CLKN

M0_DDR_RESET_N

M0_DDR_ZQCAL

M0_DDR_DQS[0]

M0_DDR_DQS_N[0]

M0_DDR_DQS[1]

M0_DDR_DQS_N[1]

M0_DDR_DQS[2]

M0_DDR_DQS_N[2]

M0_DDR_DQS[3]

M0_DDR_DQS_N[3]

M0_DDR_DM[0] M0_DDR_DM[1] M0_DDR_DM[2] M0_DDR_DM[3]

M0_DDR_DQ[0] M0_DDR_DQ[1] M0_DDR_DQ[2] M0_DDR_DQ[3] M0_DDR_DQ[4] M0_DDR_DQ[5] M0_DDR_DQ[6] M0_DDR_DQ[7] M0_DDR_DQ[8]

M0_DDR_DQ[9] M0_DDR_DQ[10] M0_DDR_DQ[11] M0_DDR_DQ[12] M0_DDR_DQ[13] M0_DDR_DQ[14] M0_DDR_DQ[15] M0_DDR_DQ[16] M0_DDR_DQ[17] M0_DDR_DQ[18] M0_DDR_DQ[19] M0_DDR_DQ[20] M0_DDR_DQ[21] M0_DDR_DQ[22] M0_DDR_DQ[23] M0_DDR_DQ[24] M0_DDR_DQ[25] M0_DDR_DQ[26] M0_DDR_DQ[27] M0_DDR_DQ[28] M0_DDR_DQ[29] M0_DDR_DQ[30] M0_DDR_DQ[31]

M0_DDR_A[0] M0_DDR_A[1] M0_DDR_A[2] M0_DDR_A[3] M0_DDR_A[4] M0_DDR_A[5] M0_DDR_A[6] M0_DDR_A[7] M0_DDR_A[8] M0_DDR_A[9]

M0_DDR_CKE

M0_DDR_ODT M0_DDR_RASN M0_DDR_CASN

M0_DDR_WEN

F15

M0_DDR_A0

F13

M0_DDR_A1

F17

M0_DDR_A2

F19

M0_DDR_A3

E10

M0_DDR_A4

E18

M0_DDR_A5

E11

M0_DDR_A6

F18

M0_DDR_A7

F11

M0_DDR_A8

F16

M0_DDR_A9

E9

M0_DDR_A10

E12

M0_DDR_A11

E13

M0_DDR_A12

E16

M0_DDR_A13

F12

M0_DDR_A14

F14

M0_DDR_A15

E19

M0_DDR_BA0

F10

M0_DDR_BA1

E15

M0_DDR_BA2

B10

M0_U_CLK

A10

M0_U_CLKN

A19

M0_D_CLK

B19

M0_D_CLKN

E14

M0_DDR_CKE

F21

M0_DDR_ODT

E21

M0_DDR_RASN

E20

M0_DDR_CASN

F20

M0_DDR_WEN

E17

M0_DDR_RESET_N

F9

B20 A20 C19 D19 A11 B11 C10 D10

D18 C20 D9 C11

D22 C15 C23 D16 B24 B15 D23 A15 C16 D21 D17 C22 C18 C21 C17 D20 C13 D7 D13 C6 D14 D6 C14 A5 C7 D12 D8 B13 C9 C12 C8 D11

R500

240

1%

M0_DDR_DQS0 M0_DDR_DQS_N0 M0_DDR_DQS1 M0_DDR_DQS_N1 M0_DDR_DQS2 M0_DDR_DQS_N2 M0_DDR_DQS3 M0_DDR_DQS_N3

M0_DDR_DM0 M0_DDR_DM1 M0_DDR_DM2 M0_DDR_DM3

M0_DDR_DQ0 M0_DDR_DQ1 M0_DDR_DQ2 M0_DDR_DQ3 M0_DDR_DQ4 M0_DDR_DQ5 M0_DDR_DQ6 M0_DDR_DQ7 M0_DDR_DQ8 M0_DDR_DQ9 M0_DDR_DQ10 M0_DDR_DQ11 M0_DDR_DQ12 M0_DDR_DQ13 M0_DDR_DQ14 M0_DDR_DQ15 M0_DDR_DQ16 M0_DDR_DQ17 M0_DDR_DQ18 M0_DDR_DQ19 M0_DDR_DQ20 M0_DDR_DQ21 M0_DDR_DQ22 M0_DDR_DQ23 M0_DDR_DQ24 M0_DDR_DQ25 M0_DDR_DQ26 M0_DDR_DQ27 M0_DDR_DQ28 M0_DDR_DQ29 M0_DDR_DQ30 M0_DDR_DQ31

VDDC15_M0

R514

R515

VDDC15_M0

R516

R517

R520 10K

100

1K 1%

M0_DDR_RESET_N

R519

M0_DDR_VREFCA

0.1uF

C504

M0_DDR_VREFDQ

0.1uF

C505

M0_D_CLK

M0_D_CLKN

M0_DDR_CKE

R541 10K

M0_U_CLK

100

R535

M0_U_CLKN

VDDC15_M0

M0_1_DDR_VREFCA

R536

1K 1%

0.1uF

R537

1K 1%

C512

VDDC15_M0

M0_1_DDR_VREFDQ

R538

1K 1%

0.1uF

R539

1K 1%

C513

M0_DDR_A0 M0_DDR_A1 M0_DDR_A2 M0_DDR_A3 M0_DDR_A4 M0_DDR_A5 M0_DDR_A6 M0_DDR_A7 M0_DDR_A8

M0_DDR_A9 M0_DDR_A10 M0_DDR_A11 M0_DDR_A12 M0_DDR_A13 M0_DDR_A14 M0_DDR_A15

M0_DDR_BA0 M0_DDR_BA1 M0_DDR_BA2

M0_D_CLK

M0_D_CLKN M0_DDR_CKE

M0_DDR_ODT

M0_DDR_RASN M0_DDR_CASN

M0_DDR_WEN

M0_DDR_RESET_N

M0_DDR_DQS0

M0_DDR_DQS_N0

M0_DDR_DQS1

M0_DDR_DQS_N1

M0_DDR_DM0 M0_DDR_DM1

M0_DDR_DQ0 M0_DDR_DQ1 M0_DDR_DQ2 M0_DDR_DQ3 M0_DDR_DQ4 M0_DDR_DQ5 M0_DDR_DQ6 M0_DDR_DQ7

M0_DDR_DQ8 M0_DDR_DQ9

M0_DDR_DQ10 M0_DDR_DQ11 M0_DDR_DQ12 M0_DDR_DQ13 M0_DDR_DQ14 M0_DDR_DQ15

DDR_SAMSUNG

IC500

K4B4G1646B-HCK0

N3

A0

P7

A1

P3

A2

N2

A3

P8

A4

P2

A5

R8

A6

R2

A7

T8

A8

R3

A9

L7

A10/AP

R7

A11

N7

A12/BC

T3

A13

T7

A14

M7

A15

M2

BA0

N8

BA1

M3

BA2

J7

CK

K7

CK

K9

CKE

L2

CS

K1

ODT

J3

RAS

K3

CAS

L3

WE

T2

RESET

F3

DQSL

G3

DQSL

C7

DQSU

B7

DQSU

E7

DML

D3

DMU

E3

DQL0

F7

DQL1

F2

DQL2

F8

DQL3

H3

DQL4

H8

DQL5

G2

DQL6

H7

DQL7

D7

DQU0

C3

DQU1

C8

DQU2

C2

DQU3

A7

DQU4

A2

DQU5

B8

DQU6

A3

DQU7

DDR3 4Gbit (x16)

VREFCA

VREFDQ

VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9

VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9

VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8

VSS_9 VSS_10 VSS_11 VSS_12

VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9

DDR_HYNIX

IC500-*1

M0_DDR_VREFCA

M0_DDR_VREFDQ

M8

H1

L8

ZQ

B2 D9 G7 K2 K8 N1 N9 R1 R9

A1 A8 C1 C9 D2 E9 F1 H2 H9

J1

NC_1

J9

NC_2

L1

NC_3

L9

NC_4

A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

B1 B9 D1 D8 E2 E8 F9 G1 G9

VDDC15_M0

R542

240

1%

H5TQ4G63AFR-PBC

N3

M8

A0

VREFCA

P7

A1

P3

A2

N2

H1

A3

VREFDQ

P8

A4

P2

A5

R8

L8

A6

ZQ

R2

A7

T8

A8

R3

B2

A9

VDD_1

L7

D9

A10/AP

VDD_2

R7

G7

A11

VDD_3

N7

K2

A12/BC

VDD_4

T3

K8

A13

VDD_5

T7

N1

A14

VDD_6

M7

N9

A15

VDD_7

R1

VDD_8

R9

M2

VDD_9

BA0

N8

BA1

M3

BA2

A1

VDDQ_1

A8

J7

VDDQ_2

CK

K7

C1

VDDQ_3

CK

K9

C9

CKE

VDDQ_4

D2

VDDQ_5

E9

L2

VDDQ_6

CS

F1

K1

VDDQ_7

ODT

H2

J3

VDDQ_8

RAS

H9

K3

VDDQ_9

CAS

L3

WE

J1

NC_1

J9

T2

NC_2

RESET

L1

NC_3

L9

NC_4

F3

DQSL

G3

DQSL

A9

C7

VSS_1

DQSU

B3

B7

VSS_2

DQSU

E1

VSS_3

G8

E7

VSS_4

DML

J2

D3

VSS_5

DMU

J8

VSS_6

M1

E3

VSS_7

DQL0

M9

F7

VSS_8

DQL1

P1

F2

VSS_9

DQL2

P9

F8

VSS_10

DQL3

T1

H3

VSS_11

DQL4

T9

H8

VSS_12

DQL5

G2

DQL6

H7

DQL7

B1

VSSQ_1

B9

D7

VSSQ_2

DQU0

D1

C3

VSSQ_3

DQU1

D8

C8

VSSQ_4

DQU2

E2

C2

VSSQ_5

DQU3

E8

A7

VSSQ_6

DQU4

F9

A2

VSSQ_7

DQU5

G1

B8

VSSQ_8

DQU6

G9

A3

VSSQ_9

DQU7

0.1uF

C534

0.1uF

C535

M0_DDR_A0 M0_DDR_A1 M0_DDR_A2 M0_DDR_A3 M0_DDR_A4 M0_DDR_A5 M0_DDR_A6 M0_DDR_A7 M0_DDR_A8

M0_DDR_A9 M0_DDR_A10 M0_DDR_A11 M0_DDR_A12 M0_DDR_A13 M0_DDR_A14 M0_DDR_A15

M0_DDR_BA0 M0_DDR_BA1 M0_DDR_BA2

M0_U_CLK

M0_U_CLKN M0_DDR_CKE

M0_DDR_ODT

M0_DDR_RASN M0_DDR_CASN

M0_DDR_WEN

M0_DDR_RESET_N

M0_DDR_DQS2

M0_DDR_DQS_N2

M0_DDR_DQS3

M0_DDR_DQS_N3

M0_DDR_DM2

M0_DDR_DM3

M0_DDR_DQ16 M0_DDR_DQ17 M0_DDR_DQ18 M0_DDR_DQ19 M0_DDR_DQ20 M0_DDR_DQ21 M0_DDR_DQ22 M0_DDR_DQ23

M0_DDR_DQ24 M0_DDR_DQ25 M0_DDR_DQ26 M0_DDR_DQ27 M0_DDR_DQ28 M0_DDR_DQ29 M0_DDR_DQ30 M0_DDR_DQ31

DDR_SAMSUNG

IC502

K4B4G1646B-HCK0

DDR3

N3

4Gbit

A0

P7

(x16)

A1

P3

A2

N2

A3

P8

A4

P2

A5

R8

A6

R2

A7

T8

A8

R3

A9

L7

A10/AP

R7

A11

N7

A12/BC

T3

A13

T7

A14

M7

A15

M2

BA0

N8

BA1

M3

BA2

J7

CK

K7

CK

K9

CKE

L2

CS

K1

ODT

J3

RAS

K3

CAS

L3

WE

T2

RESET

F3

DQSL

G3

DQSL

C7

DQSU

B7

DQSU

E7

DML

D3

DMU

E3

DQL0

F7

DQL1

F2

DQL2

F8

DQL3

H3

DQL4

H8

DQL5

G2

DQL6

H7

DQL7

D7

DQU0

C3

DQU1

C8

DQU2

C2

DQU3

A7

DQU4

A2

DQU5

B8

DQU6

A3

DQU7

VREFCA

VREFDQ

VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9

VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9

VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8

VSS_9 VSS_10 VSS_11 VSS_12

VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9

0.1uF

DDR_HYNIX

IC502-*1

H5TQ4G63AFR-PBC

N3

A0

P7

A1

P3

A2

N2

A3

P8

A4

P2

A5

R8

A6

R2

A7

T8

A8

R3

A9

L7

A10/AP

R7

A11

N7

A12/BC

T3

A13

T7

A14

M7

A15

M2

BA0

N8

BA1

M3

BA2

J7

CK

K7

CK

K9

CKE

L2

CS

K1

ODT

J3

RAS

K3

CAS

L3

WE

T2

RESET

F3

DQSL

G3

DQSL

C7

DQSU

B7

DQSU

E7

DML

D3

DMU

E3

DQL0

F7

DQL1

F2

DQL2

F8

DQL3

H3

DQL4

H8

DQL5

G2

DQL6

H7

DQL7

D7

DQU0

C3

DQU1

C8

DQU2

C2

DQU3

A7

DQU4

A2

DQU5

B8

DQU6

A3

DQU7

M8

VREFCA

H1

VREFDQ

L8

ZQ

B2

VDD_1

D9

VDD_2

G7

VDD_3

K2

VDD_4

K8

VDD_5

N1

VDD_6

N9

VDD_7

R1

VDD_8

R9

VDD_9

A1

VDDQ_1

A8

VDDQ_2

C1

VDDQ_3

C9

VDDQ_4

D2

VDDQ_5

E9

VDDQ_6

F1

VDDQ_7

H2

VDDQ_8

H9

VDDQ_9

J1

NC_1

J9

NC_2

L1

NC_3

L9

NC_4

A9

VSS_1

B3

VSS_2

E1

VSS_3

G8

VSS_4

J2

VSS_5

J8

VSS_6

M1

VSS_7

M9

VSS_8

P1

VSS_9

P9

VSS_10

T1

VSS_11

T9

VSS_12

B1

VSSQ_1

B9

VSSQ_2

D1

VSSQ_3

D8

VSSQ_4

E2

VSSQ_5

E8

VSSQ_6

F9

VSSQ_7

G1

VSSQ_8

G9

VSSQ_9

M0_1_DDR_VREFCA

M8

H1

L8

ZQ

B2 D9 G7 K2 K8 N1 N9 R1 R9

A1 A8 C1 C9 D2 E9 F1 H2 H9

J1

NC_1

J9

NC_2

L1

NC_3

L9

NC_4

A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

B1 B9 D1 D8 E2 E8 F9 G1 G9

M0_1_DDR_VREFDQ

VDDC15_M0

R544

240 1%

C566 C567

IC100

LG1154D_H13D

M1_DDR_A[10] M1_DDR_A[11] M1_DDR_A[12] M1_DDR_A[13] M1_DDR_A[14] M1_DDR_A[15]

M1_DDR_BA[0] M1_DDR_BA[1] M1_DDR_BA[2]

M1_DDR_U_CLK

M1_DDR_U_CLKN

M1_DDR_D_CLK

M1_DDR_D_CLKN

M1_DDR_RESET_N

M1_DDR_ZQCAL

M1_DDR_DQS[0]

M1_DDR_DQS_N[0]

M1_DDR_DQS[1]

M1_DDR_DQS_N[1]

M1_DDR_DQS[2]

M1_DDR_DQS_N[2]

M1_DDR_DQS[3]

M1_DDR_DQS_N[3]

M1_DDR_DM[0] M1_DDR_DM[1] M1_DDR_DM[2] M1_DDR_DM[3]

M1_DDR_DQ[0] M1_DDR_DQ[1] M1_DDR_DQ[2] M1_DDR_DQ[3] M1_DDR_DQ[4] M1_DDR_DQ[5] M1_DDR_DQ[6] M1_DDR_DQ[7] M1_DDR_DQ[8]

M1_DDR_DQ[9] M1_DDR_DQ[10] M1_DDR_DQ[11] M1_DDR_DQ[12] M1_DDR_DQ[13] M1_DDR_DQ[14] M1_DDR_DQ[15] M1_DDR_DQ[16] M1_DDR_DQ[17] M1_DDR_DQ[18] M1_DDR_DQ[19] M1_DDR_DQ[20] M1_DDR_DQ[21] M1_DDR_DQ[22] M1_DDR_DQ[23] M1_DDR_DQ[24] M1_DDR_DQ[25] M1_DDR_DQ[26] M1_DDR_DQ[27] M1_DDR_DQ[28] M1_DDR_DQ[29] M1_DDR_DQ[30] M1_DDR_DQ[31]

M1_DDR_A[0] M1_DDR_A[1] M1_DDR_A[2] M1_DDR_A[3] M1_DDR_A[4] M1_DDR_A[5] M1_DDR_A[6] M1_DDR_A[7] M1_DDR_A[8] M1_DDR_A[9]

M1_DDR_CKE

M1_DDR_ODT M1_DDR_RASN M1_DDR_CASN

M1_DDR_WEN

Real USE : 1Gbit

H5TQ1G63DFR-PBC(x16)

1Gbit : T7(NC_6)

N6

M1_DDR_A0

R6

M1_DDR_A1

L6

M1_DDR_A2

J6

M1_DDR_A3

U5

M1_DDR_A4

J5

M1_DDR_A5

T5

M1_DDR_A6

K6

M1_DDR_A7

U6

M1_DDR_A8

M6

M1_DDR_A9

V5

M1_DDR_A10

R5

M1_DDR_A11

P5

M1_DDR_A12

L5

M1_DDR_A13

T6

M1_DDR_A14

P6

M1_DDR_A15

H5

M1_DDR_BA0

V6

M1_DDR_BA1

M5

M1_DDR_BA2

R2 R1 F1 F2 N5

G6 F5 G5 H6

K5

F6

E2 E1 F3 F4 P1 P2 R3 R4

G4 E3 T4 P3

C4 K3 B3 J4 A3 K2 B4 K1 J3 D4 H4 C3 G3 D3 H3 E4 M3 V4 M4 W3 L4 W4 L3 Y2 V3 N4 U4 M2 T3 N3 U3 P4

240

M1_U_CLK M1_U_CLKN M1_D_CLK M1_D_CLKN M1_DDR_CKE

M1_DDR_ODT M1_DDR_RASN M1_DDR_CASN M1_DDR_WEN

M1_DDR_RESET_N

R501

1%

M1_DDR_DQS0 M1_DDR_DQS_N0 M1_DDR_DQS1 M1_DDR_DQS_N1 M1_DDR_DQS2 M1_DDR_DQS_N2 M1_DDR_DQS3 M1_DDR_DQS_N3

M1_DDR_DM0 M1_DDR_DM1 M1_DDR_DM2 M1_DDR_DM3

M1_DDR_DQ0 M1_DDR_DQ1 M1_DDR_DQ2 M1_DDR_DQ3 M1_DDR_DQ4 M1_DDR_DQ5 M1_DDR_DQ6 M1_DDR_DQ7 M1_DDR_DQ8 M1_DDR_DQ9 M1_DDR_DQ10 M1_DDR_DQ11 M1_DDR_DQ12 M1_DDR_DQ13 M1_DDR_DQ14 M1_DDR_DQ15

M1_DDR_DQ16 M1_DDR_DQ17 M1_DDR_DQ18 M1_DDR_DQ19 M1_DDR_DQ20 M1_DDR_DQ21 M1_DDR_DQ22 M1_DDR_DQ23 M1_DDR_DQ24 M1_DDR_DQ25 M1_DDR_DQ26 M1_DDR_DQ27 M1_DDR_DQ28 M1_DDR_DQ29 M1_DDR_DQ30 M1_DDR_DQ31

VDDC15_M1

R510

R511

VDDC15_M1

R512

R513

VDDC15_M1

100

R518

1K 1%

C500

1K 1%

C501

R521 10K

M1_D_CLK

M1_D_CLKN

M1_DDR_VREFCA

0.1uF

M1_DDR_VREFDQ

0.1uF

M1_DDR_RESET_N

M1_DDR_CKE

M1_DDR_A0

M1_DDR_RESET_N

M1_DDR_DQS0

M1_DDR_DQS_N0

M1_DDR_DQS1

M1_DDR_DQS_N1

M1_DDR_DM0 M1_DDR_DM1

M1_DDR_A1 M1_DDR_A2 M1_DDR_A3 M1_DDR_A4 M1_DDR_A5 M1_DDR_A6 M1_DDR_A7 M1_DDR_A8

M1_DDR_A9 M1_DDR_A10 M1_DDR_A11 M1_DDR_A12 M1_DDR_A13 M1_DDR_A14 M1_DDR_A15

M1_DDR_BA0 M1_DDR_BA1 M1_DDR_BA2

M1_D_CLK

M1_D_CLKN M1_DDR_CKE

M1_DDR_ODT

M1_DDR_RASN

M1_DDR_CASN

M1_DDR_WEN

M1_DDR_DQ0 M1_DDR_DQ1 M1_DDR_DQ2 M1_DDR_DQ3 M1_DDR_DQ4 M1_DDR_DQ5 M1_DDR_DQ6 M1_DDR_DQ7

M1_DDR_DQ8 M1_DDR_DQ9

M1_DDR_DQ10

M1_DDR_DQ11 M1_DDR_DQ12 M1_DDR_DQ13 M1_DDR_DQ14 M1_DDR_DQ15

R540 10K

M1_U_CLK

100

R530

M1_U_CLKN

VDDC15_M1

M1_1_DDR_VREFCA

R531

1K 1%

0.1uF

R532

1K 1%

C508

VDDC15_M1

M1_1_DDR_VREFDQ

R533

1K 1%

0.1uF

R534

1K 1%

C509

DDR_SAMSUNG

IC501

K4B4G1646B-HCK0

N3

DDR3

A0

P7

4Gbit

A1

P3

(x16)

A2

N2

A3

P8

A4

P2

A5

R8

A6

R2

A7

T8

A8

R3

A9

L7

A10/AP

R7

A11

N7

A12/BC

T3

A13

T7

A14

M7

A15

M2

BA0

N8

BA1

M3

BA2

J7

CK

K7

CK

K9

CKE

L2

CS

K1

ODT

J3

RAS

K3

CAS

L3

WE

T2

RESET

F3

DQSL

G3

DQSL

C7

DQSU

B7

DQSU

E7

DML

D3

DMU

E3

DQL0

F7

DQL1

F2

DQL2

F8

DQL3

H3

DQL4

H8

DQL5

G2

DQL6

H7

DQL7

D7

DQU0

C3

DQU1

C8

DQU2

C2

DQU3

A7

DQU4

A2

DQU5

B8

DQU6

A3

DQU7

VREFCA

VREFDQ

VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9

VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9

VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8

VSS_9 VSS_10 VSS_11 VSS_12

VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9

M1_DDR_VREFCA

M1_DDR_VREFDQ

M8

H1

L8

R543

ZQ

VDDC15_M1

B2 D9 G7 K2 K8 N1 N9 R1 R9

A1 A8 C1 C9 D2 E9 F1 H2 H9

J1

NC_1

J9

NC_2

L1

NC_3

L9

NC_4

A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

B1 B9 D1 D8 E2 E8 F9 G1 G9

240

C529

0.1uF

C530

0.1uF

DDR_HYNIX IC501-*1

H5TQ4G63AFR-PBC

M8

N3

VREFCA

A0

P7

A1

P3

A2

H1

N2

VREFDQ

A3

P8

A4

P2

A5

R8

L8

A6

ZQ

R2

A7

T8

A8

R3

B2

A9

VDD_1

L7

D9

A10/AP

VDD_2

R7

G7

A11

VDD_3

K2

N7

A12/BC

VDD_4

K8

T3

VDD_5

A13

T7

N1

A14

VDD_6

N9

M7

VDD_7

A15

R1

VDD_8

R9

M2

VDD_9

BA0

N8

BA1

M3

BA2

A1

VDDQ_1

A8

J7

VDDQ_2

CK

C1

K7

VDDQ_3

CK

C9

K9

VDDQ_4

CKE

D2

VDDQ_5

E9

L2

VDDQ_6

CS

F1

K1

VDDQ_7

ODT

H2

J3

VDDQ_8

RAS

H9

K3

VDDQ_9

CAS

L3

WE

J1

NC_1

J9

T2

NC_2

RESET

L1

NC_3

L9

NC_4

F3

DQSL

G3

DQSL

A9

C7

VSS_1

DQSU

B3

B7

VSS_2

DQSU

E1

VSS_3

G8

E7

VSS_4

DML

J2

D3

VSS_5

DMU

J8

VSS_6

M1

E3

VSS_7

DQL0

M9

F7

VSS_8

DQL1

P1

F2

VSS_9

DQL2

P9

F8

VSS_10

DQL3

T1

H3

VSS_11

DQL4

T9

H8

VSS_12

DQL5

G2

DQL6

H7

DQL7

B1

VSSQ_1

B9

D7

VSSQ_2

DQU0

D1

C3

VSSQ_3

DQU1

D8

C8

VSSQ_4

DQU2

E2

C2

VSSQ_5

DQU3

E8

A7

VSSQ_6

DQU4

F9

A2

VSSQ_7

DQU5

G1

B8

VSSQ_8

DQU6

G9

A3

VSSQ_9

DQU7

DDR3 1.5V bypass Cap - Place these caps near Memory

4Gbit : T7(A14)

M1_DDR_A0 M1_DDR_A1 M1_DDR_A2 M1_DDR_A3 M1_DDR_A4 M1_DDR_A5 M1_DDR_A6 M1_DDR_A7 M1_DDR_A8

M1_DDR_A9 M1_DDR_A10 M1_DDR_A11 M1_DDR_A12 M1_DDR_A13 M1_DDR_A14 M1_DDR_A15

M1_DDR_BA0 M1_DDR_BA1 M1_DDR_BA2

M1_U_CLK

M1_U_CLKN M1_DDR_CKE

M1_DDR_ODT

M1_DDR_RASN M1_DDR_CASN

M1_DDR_WEN

M1_DDR_RESET_N

M1_DDR_DQS2

M1_DDR_DQS_N2

M1_DDR_DQS3

M1_DDR_DQS_N3

M1_DDR_DM2 M1_DDR_DM3

M1_DDR_DQ16 M1_DDR_DQ17 M1_DDR_DQ18 M1_DDR_DQ19 M1_DDR_DQ20 M1_DDR_DQ21 M1_DDR_DQ22 M1_DDR_DQ23

M1_DDR_DQ24 M1_DDR_DQ25 M1_DDR_DQ26 M1_DDR_DQ27 M1_DDR_DQ28 M1_DDR_DQ29 M1_DDR_DQ30 M1_DDR_DQ31

DDR_SAMSUNG

IC503

K4B4G1646B-HCK0

N3

DDR3

A0

P7

4Gbit

A1

P3

(x16)

A2

N2

A3

P8

A4

P2

A5

R8

A6

R2

A7

T8

A8

R3

A9

L7

A10/AP

R7

A11

N7

A12/BC

T3

A13

T7

A14

M7

A15

M2

BA0

N8

BA1

M3

BA2

J7

CK

K7

CK

K9

CKE

L2

CS

K1

ODT

J3

RAS

K3

CAS

L3

WE

T2

RESET

F3

DQSL

G3

DQSL

C7

DQSU

B7

DQSU

E7

DML

D3

DMU

E3

DQL0

F7

DQL1

F2

DQL2

F8

DQL3

H3

DQL4

H8

DQL5

G2

DQL6

H7

DQL7

D7

DQU0

C3

DQU1

C8

DQU2

C2

DQU3

A7

DQU4

A2

DQU5

B8

DQU6

A3

DQU7

VREFCA

VREFDQ

VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9

VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9

VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8

VSS_9 VSS_10 VSS_11 VSS_12

VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9

M1_1_DDR_VREFCA

M1_1_DDR_VREFDQ

M8

H1

L8

R545

ZQ

VDDC15_M1 B2 D9 G7 K2 K8 N1 N9 R1 R9

A1 A8 C1 C9 D2 E9 F1 H2 H9

J1

NC_1

J9

NC_2

L1

NC_3

L9

NC_4

A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

B1 B9 D1 D8 E2 E8 F9 G1 G9

240

C561

0.1uF

C562

0.1uF

DDR_HYNIX

IC503-*1

H5TQ4G63AFR-PBC

M8

N3

VREFCA

A0

P7

A1

P3

A2

H1

N2

VREFDQ

A3

P8

A4

P2

A5

R8

L8

A6

ZQ

R2

A7

T8

A8

R3

B2

A9

VDD_1

L7

D9

A10/AP

VDD_2

R7

G7

A11

VDD_3

K2

N7

A12/BC

VDD_4

K8

T3

VDD_5

A13

T7

N1

A14

VDD_6

N9

M7

VDD_7

A15

R1

VDD_8

R9

M2

VDD_9

BA0

N8

BA1

M3

BA2

A1

VDDQ_1

A8

J7

VDDQ_2

CK

C1

K7

VDDQ_3

CK

C9

K9

VDDQ_4

CKE

D2

VDDQ_5

E9

L2

VDDQ_6

CS

F1

K1

VDDQ_7

ODT

H2

J3

VDDQ_8

RAS

H9

K3

VDDQ_9

CAS

L3

WE

J1

NC_1

J9

T2

NC_2

RESET

L1

NC_3

L9

NC_4

F3

DQSL

G3

DQSL

A9

C7

VSS_1

DQSU

B3

B7

VSS_2

DQSU

E1

VSS_3

G8

E7

VSS_4

DML

J2

D3

VSS_5

DMU

J8

VSS_6

M1

E3

VSS_7

DQL0

M9

F7

VSS_8

DQL1

P1

F2

VSS_9

DQL2

P9

F8

VSS_10

DQL3

T1

H3

VSS_11

DQL4

T9

H8

VSS_12

DQL5

G2

DQL6

H7

DQL7

B1

VSSQ_1

B9

D7

VSSQ_2

DQU0

D1

C3

VSSQ_3

DQU1

D8

C8

VSSQ_4

DQU2

E2

C2

VSSQ_5

DQU3

E8

A7

VSSQ_6

DQU4

F9

A2

VSSQ_7

DQU5

G1

B8

VSSQ_8

DQU6

G9

A3

VSSQ_9

DQU7

DDR3 1.5V bypass Cap - Place these caps near Memory

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

BSD-NC4_H005-HD

2012-09-14

MAIN DDR

PCM_RESET

LGE Internal Use Only

/PCM_WAIT

PCM_INPACK

/PCM_IORD /PCM_IOWR

R701 R702 R700

CI_IN_TS_DATA[0-7]

R704

10K OPT

CI

33

CI

33

OPT

33

+5V_CI_ON

R706 10K

OPT

+5V_CI_ON

R707

10K

OPT

CI_VS1

PCM_INPACK

/PCM_CE2

10K

R709

10K

CI

R708

OPT

C702

0.1uF CI

/CI_CD1 CI_TS_DATA[3] CI_TS_DATA[4] CI_TS_DATA[5] CI_TS_DATA[6] CI_TS_DATA[7]

/PCM_CE2

CI_VS1

CI_IN_TS_DATA[0] CI_IN_TS_DATA[1] CI_IN_TS_DATA[2] CI_IN_TS_DATA[3]

CI_IN_TS_DATA[4] CI_IN_TS_DATA[5] CI_IN_TS_DATA[6] CI_IN_TS_DATA[7]

CI_TS_CLK

/PCM_REG

CI_TS_VAL

CI_TS_SYNC CI_TS_DATA[0] CI_TS_DATA[1] CI_TS_DATA[2]

/CI_CD2

C703

4.7uF 10V

CI

R710

10K

R711

OPT

+5V_CI_ON

CI_ADDR[11] CI_ADDR[9]

CI_ADDR[13]

R722 33

C707

0.1uF

16V

CI_ADDR[12]

CI_ADDR[7] CI_ADDR[6] CI_ADDR[5]

CI_ADDR[4]

CI_ADDR[3]

CI_ADDR[2] CI_ADDR[1] CI_ADDR[0]

CI_DATA[0-7]

OPT

+5V_CI_ON

CI_ADDR[10]

CI_ADDR[11] CI_ADDR[9] CI_ADDR[8] CI_ADDR[13] CI_ADDR[14]

CI_ADDR[12] CI_ADDR[7] CI_ADDR[6] CI_ADDR[5] CI_ADDR[4] CI_ADDR[3] CI_ADDR[2] CI_ADDR[1] CI_ADDR[0]

/PCM_CE1

+5V_CI_ON

R724

10K

OPT

+5V_CI_ON

R723

10K

CI CI_DATA[0] CI_DATA[1]

/PCM_OE

R725

10K

OPT

CI

/PCM_WE /PCM_IRQA

CI_DATA[0-7]

CI_DATA[2] CI_DATA[3]

CI_DATA[0-7]

CI_DATA[4] CI_DATA[5] CI_DATA[6] CI_DATA[7]

AR712

33

CI

AR713

33

EB_DATA[0] EB_DATA[1] EB_DATA[2] EB_DATA[3]

EB_DATA[4] EB_DATA[5] EB_DATA[6] EB_DATA[7]

EB_DATA[0-7]

R712 10K OPT

100

R716

CI

0

OPT

0

R715

OPT

CI

R714 0

CI

R717 100

R713

0

OPT

CI

JK700

10120698-015LF

35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

65 66 67 68

R720

R718

R719

10K OPT

CI_DATA[3] CI_DATA[4] CI_DATA[5] CI_DATA[6] CI_DATA[7]

CI

R721 33

C706 0.1uF

0

OPT

10K

OPT

C705 12pF 50V OPT

CI

CI_DATA[0] CI_DATA[1] CI_DATA[2]

CI_IN_TS_VAL CI_IN_TS_CLK

CI_IN_TS_SYNC

CI_ADDR[10]

CI_ADDR[8]

CI_ADDR[14]

CI

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 2660 2761 2862 2963 3064 31 32 33 34

G1G2

69

TPO_DATA[0-7]

/CI_CD2 /CI_CD1

TPO_CLK TPO_SOP TPO_VAL

R703

+5V_NORMAL

10K

R705

CI C700

0.1uF 16V

TPO_DATA[0] TPO_DATA[1] TPO_DATA[2] TPO_DATA[3] TPO_DATA[4] TPO_DATA[5] TPO_DATA[6] TPO_DATA[7]

10K

CI C701

0.1uF 16V

PCM_INPACK

CI_TS_CLK

CI_TS_VAL

CI_TS_SYNC

CI_TS_DATA[7]

CI_TS_DATA[6]

CI_TS_DATA[5]

CI_TS_DATA[4]

/PCM_WAIT /PCM_IRQA

CI

AR701

33

AR706

CI

AR705

33

AR702

100

AR703

CI

100

AR704

CI

100

CI

33

CI_IN_TS_DATA[0] CI_IN_TS_DATA[1] CI_IN_TS_DATA[2] CI_IN_TS_DATA[3] CI_IN_TS_DATA[4] CI_IN_TS_DATA[5] CI_IN_TS_DATA[6] CI_IN_TS_DATA[7]

CI_IN_TS_CLK CI_IN_TS_SYNC

CI_IN_TS_VAL

CAM_WAIT_N CAM_IREQ_N

CAM_CD2_N

CAM_CD1_N

CAM_INPACK_N

TPI_VAL TPI_SOP

TPI_DATA[7] TPI_DATA[6] TPI_DATA[5] TPI_DATA[4]

C704 12pF 50V OPT

TPI_CLK

CI_ADDR[0] CI_ADDR[1] CI_ADDR[2] CI_ADDR[3]

CI_ADDR[4] CI_ADDR[5] CI_ADDR[6] CI_ADDR[7]

CI_ADDR[8]

CI_ADDR[9] CI_ADDR[10] CI_ADDR[11]

CI

AR707

33

CI

AR708

33

CI

AR709

33

EB_ADDR[0] EB_ADDR[1] EB_ADDR[2] EB_ADDR[3]

EB_ADDR[4] EB_ADDR[5] EB_ADDR[6] EB_ADDR[7]

EB_ADDR[8] EB_ADDR[9] EB_ADDR[10] EB_ADDR[11]

CI_ADDR[12] CI_ADDR[13] CI_ADDR[14]

/PCM_REG

/PCM_OE /PCM_WE

/PCM_IORD /PCM_IOWR

CI

AR711

33

CI

AR710

33

EB_ADDR[12] EB_ADDR[13] EB_ADDR[14] CAM_REG_N

EB_OE_N EB_WE_N EB_BE_N1 EB_BE_N0

CI CI_TS_DATA[3] CI_TS_DATA[2] CI_TS_DATA[1] CI_TS_DATA[0]

AR700

100

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

TPI_DATA[3] TPI_DATA[2] TPI_DATA[1] TPI_DATA[0]

BSD-NC4_H007-HD

2012-10-20

PCMCIA

+3.5V_ST

LGE Internal Use Only

R2300

RL_ON

10K

C2306

0.1uF 50V

L2304

UBW2012-121F

C2307

0.1uF 16V

UBW2012-121F

L2303

+3.5V_ST

+12V

eMMC POWER

+3.3V_NORMAL

+12V

Switching freq: 700K

+12V

Switching freq: 700K

L2302

BLM18PG121SN1D

L2300 BLM18PG121SN1D

C2301 10uF 16V

L2305 BLM18PG121SN1D

C2304 10uF 16V

3.3V_EMMC

POWER_ON/OFF2_3

1

10K

R2301

2

C2305

0.1uF 16V

Q2300 MMBT3906(NXP)

3

C2300 22uF 10V

PWR ON

3.5V

3.5V GND 24V GND 12V 12V GND

P2300

SMAW200-H18S1

1 3 5 7 9 11 13 15 17

19

+1.0V_VDD

R2304 10K

1%

R2302

R1

C2308 100pF

50V

DCDC_TI

R2

11K

R2306

33K

1%

C2310 1uF 10V

VREG5

C2312 3300pF 50V

Vout=0.765*(1+R1/R2)

+3.3V_NORMAL

R2311

POWER_ON/OFF1

R1

C2325 100pF

50V

OPT

10K

1% C2332

R2308

51K

R2319

15K

R2

C2326

C2328

1uF

3300pF

10V

1%

50V

Vout=0.765*(1+R1/R2)

INV ON

2

PDIM#1

4

PDIM#2

6

GND

8

24V

10

GND

12

12V

14

24V

16

GND

18

DCDC_TI

TPS54327DDAR

EN

1

VFB

2

3

SS

4

TPS54327DDAR

EN

1

VFB

2

VREG5

3

SS

4

3A

IC2300

9

THERMAL

IC2301

THERMAL

PANEL_POWER

+12V

L2313

UBW2012-121F

C2331

0.1uF 50V

R2317

33K

R2318

5.6K

C

Q2301

B

IC2302

THERMAL

1.5A

MMBT3904(NXP)

E

8

9

7

6

5

R2314

10K

AP7173-SPG-13 HF(DIODES)

IN

1

PG

2

VCC

3

EN

4

[EP]

OUT

FB

SS

GND

C2333 10uF

16V

Q2302

AO3407A

S

G

C2337 2200pF 50V

D

R2321 2K 1%

R2346

R2347

5.6K

LVDS_DISCHARGE

R2322

R1

4.3K 1%

R2

PANEL_20V

PWM_DIM2

R2309 100

L2306

UBW2012-121F

C2316

0.1uF

JP2308

JP2309

JP2310

50V

+3.3V_NORMAL

R2310 1K

INV_CTL

+24V

PWM_DIM

L/DIM0_MOSI L/DIM0_MOSI

L/DIM0_VS L/DIM0_VS

L/DIM0_SCLK L/DIM0_SCLK

+2.5V

POWER_ON/OFF2_1

PANEL_CTL

+3.3V_NORMAL

+5V_NORMAL

R2312 10K

C2327 10uF 10V

Vout=0.8*(1+R1/R2)

LG1154A

+1.23V_CORE

+12V

L2301

+1.1V_VDD

C2303

C2302 180pF 50V

R2303

16K

R2305

15K

10uF 16V

R1

1/16W

1%

R2

1/16W

1%

Vout(1.24V)=0.6*(1+16k/15k)

R2307 120K

1/16W 1%

RT/CLK

PVIN_1

PVIN_2

VSENSE

C2313

4.7uF 16V

GND_1

GND_2

VIN

IC2303

TPS54821RHL

1

2

THERMAL

3

4

5

6

8A

7

[EP]GND

PWRGD

14

C2318

BOOT

15

13

0.1uF 16V

PH_2

12

PH_1

11

EN

10

SS/TR

9

COMP

8

1.3K R2313

C2315

4700pF 50V

L2308

1uH

C2322 22uF 10V

R2316 1K

C2321

22000pF 50V

C2320

47pF 50V

1/16W

5%

R2315 0

8

7

6

5

[EP]GND

VIN

VBST

SW

GND

0.1uF C2314

16V

NR5040T2R2N

L2307

2.2uH

+1.0V_VDD

C2317

C2319

22uF

10V

+3.3V_NORMAL

2.5V

ZD2300

OPT

DCDC_RT

IC2300-*1

RT7266ZSP

[EP]GND

VIN

EN

8

1

FB

BOOT

9

2

7

THERMAL

PVCC

SW

3

6

SS

GND

4

5

Vout=0.6*(1+R1/R2)

[EP]GND

VIN

8

9

7

6

5

VBST

SW

GND

0.1uF

16V

L2309

3.6uH

SM-8040

C2339

22uF

10V

C2340 22uF 10V

5V

ZD2301

POWER UP SEQUENCE

5V/3.3V->2.5V->1.5V/1.1V->1.0V LG1154D : 3.3V->2.5V->1.5V->1.1V

LG1154AN : 3.3V->2.5V->1.0V

PANEL_VCC

LVDS_DISCHARGE

OPT

C2343 22uF 10V

+1.1V_VDD

C2341

22uF 10V

C2347

0.1uF 50V

+2.5V_Normal

C2346 10uF 10V

C2323 22uF 10V

POWER_ON/OFF2_2

C2348

0.1uF 16V

OPT

2.5V

ZD2302

ZD2304

Power_DET

DDR MAIN 1.5V

5V

+3.5V_ST

L2318

C2350 10uF 10V

+5.0V normal & USB

+24V

+12V

L2311

L2314

BLM18PG121SN1D

OLED

NON_OLED

C2309 10uF 35V

+12V

PD_+12V

R2325

2.7K 1%

PD_+12V R2326

1.2K 1%

VIN_1

VIN_2

GND_1

GND_2

+3.5V_ST

PANEL_20V

R2327

5.6K 1%

R2328

1.3K 1%

EP[GND]

1

2

3

4

PD_+3.5V R2330 0 5%

10K

R2331

THERMAL

17

IC2305

TPS54319TRE

3A

5

6

AGND

VSENSE

3A

C2354

0.1uF 16V

DCDC_TI

7

COMP

BOOT14PWRGD15EN16VIN_3

13

12

11

10

9

8

RT/CLK

1/16W 5%

$ 0.145

C2355

0.1uF 16V

C2356

0.1uF 16V

PH_3

PH_2

PH_1

SS/TR

R2334 15K

C2358

0.1uF

16V

R2335

VCC

C2359

0.01uF 50V

330K1/16W 5%

4700pF

R2337 100K

IC2307

NCP803SN293

3

1

GND

R2336 100K

IC2308

NCP803SN293

3

1

GND

POWER_ON/OFF2_2

NR5040T3R3N

C2360

50V

Vout=0.827*(1+R1/R2)=1.521V

IC2304

C2311

0.1uF 50V

RT8289GSP

C2324

0.01uF 50V

BOOT

1

NC_1

2

NC_2

3

FB

4

5A

1%

51K

R1

R2343

16K

R2344

1%

C2329 150pF 50V

R2

9

THERMAL

8

7

6

5

[EP]GND

SW

VIN

GND

EN

Vout=1.222*(1+R1/R2)

L2320

3.3uH

2

C2361 22uF 10V

D2300

B540C

RESET

+3.5V_ST

R2338 10K OPT

OLED : 20V DET = POWER_ON/OFF2_4

POWER_DET

C2365

0.1uF 16V

not to RESET at 8kV ESD

R2348

ST_3.5V-->3.5V

POWER_ON/OFF2_4

0

24V-->3.48V 20V-->3.51V 12V-->3.58V

LG1154D

+1.5V_DDR

C2362 22uF 10V

R2339

R1

47K 1%

R2

R2340 56K

1/16W

1%

L2310

L2312

4.7uH

40V

C2335

0.1uF

C2330 22uF 10V

16V

DCDC_TI C2364 100pF 50V

VIN_1

VIN_2

GND_1

GND_2

1

2

3

4

C2334 22uF 10V

ZD2303

THERMAL

5

AGND

2.5V OPT

IC2305-*1 RT8079AGQW

DCDC_RT

6FB7

COMP

+5V_NORMAL

C2336 10uF 10V

POWER_ON/OFF1

R2345 10K

BOOT14PGOOD15EN16VIN_317[EP]GND

13

RT/SYNC

SW_3

12

SW_2

11

SW_1

10

SS/TR

9

8

C2338

0.1uF 50V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

BSD-NC4_H039-HD

NC4_H13

POWER_BLOCK(OLED) 23

2013.03.05

Renesas MICOM

LGE Internal Use Only

For Debug

+3.5V_ST

MICOM_DEBUG

P3000

12507WS-04L

1

2

3

4

5

GP4 High/MID Power SEQUENCE

POWER_ON/OFF!

POWER_ON/OFF2_1

POWER_ON/OFF2_2

POWER_ON/OFF2_3

POWER_ON/OFF2_4

SOC_RESET

Don’t remove R3014, not making float P40

R3016 1K

R3014 10K

MICOM_DEBUG

MICOM_RESET

For CEC

CEC_REMOTE

D3000

BAT54_SUZHO

R3033 27K

+3.5V_ST

G

S

D

Q3001 RUE003N02 HDMI_CEC_FET_ROHM

G

S

D

R3034 120K

Q3001-*1 SI1012CR-T1-GE3 HDMI_CEC_FET_VISHAY

HDMI_CEC

EDID_WP

CAM_PWR_ON_CMD

I2C_SCL_MICOM

I2C_SDA_MICOM

EDID_WP

PANEL_CTL

WOL/WIFI_POWER_ON

HDMI_CEC

POWER_ON/OFF2_2

POWER_ON/OFF2_3

EYE_SDA

EYE_SCL

CAM_PWR_ON_CMD

+3.5V_ST

8pF

C3003 8pF

C3002

X3000

HDMI_WAUP:HDMI_INIT

MHL_DET MHL_DET

10K

GND

R3032

+3.5V_ST

VDD

48

13

VSS

47

14

C3001 0.47uF

REGC

46

15

C3000

+3.5V_ST

R3021

10K

P31/TI03/TO03/INTP4

IR

P75/KR5/INTP9/SCK01/SCL01

P74/KR4/INTP8/SI01/SDA01

P73/KR3/SO01 P72/KR2/SO21

P71/KR1/SI21/SDA21

P70/KR0/SCK21/SCL21

P30/INTP3/RTC1HZ/SCK11/SCL11

EYE_Q

R3035

3.3K

R3036

3.3K

EYE_Q

0.1uF

P60/SCLA0 P61/SDAA0

P62 P63

1 2 3 4 5 6 7 8 9 10 11 12

32.768KHz R3028

4.7M OPT

Ready For

Commercial

P124/XT2/EXCLKS

P123/XT1

P137/INTP0

P122/X2/EXCLK

P121/X1

41

42

43

44

45

IC3000

R5F100GEAFB

MICOM_LEAD_Au

16

17

18

19

20

MICOM_RESET

R3029 22

MICOM_RESET_22OHM

P40/TOOL0

RESET

39

40

21

LOGO_LIGHT

MICOM_DEBUG

LOGO_LIGHT

C3004

0.1uF 16V

P120/ANI19

P41/TI07/TO07

37

38

36 35 34 33 32 31 30 29 28 27 26 25

22

23

24

+3.5V_ST

10K

MICOM_RESET_SW

SW3000

R3030

JTP-1127WEM

4 3

12

ST_BY_DET_CAMST_BY_DET_CAM

MICOM_RESET_33OHM

R3029-*1 33

R3031

270K

OPT

P140/PCLBUZ0/INTP6 P00/TI00/TXD1 P01/TO00/RXD1 P130 P20/ANI0/AVREFP P21/ANI1/AVREFM P22/ANI2 P23/ANI3 P24/ANI4 P25/ANI5 P26/ANI6 P27/ANI7



RL_ON

SCART_MUTE

POWER_ON/OFF2_4

POWER_ON/OFF2_1

KEY2

KEY1

MODEL1_OPT_1

MODEL1_OPT_4

MODEL1_OPT_0

SIDE_HP_MUTE

MODEL1_OPT_3

MODEL1_OPT_2

SCART_MUTE

POWER_ON/OFF2_4

MICOM MODEL OPTION

+3.5V_ST

MICOM_H13

R3006 10K

R3003 10K

MICOM_NC4_8PIN

MICOM_M13

R3004 10K

R3001 10K

MICOM_GP3_12/15PIN

MICOM_PDP

R3007 10K

R3010 10K

MICOM_TOUCH_KEY

R3005 10K

R3008 10K

MICOM_LCD/OLED

MICOM_TACT_KEY

R3013 10K

MICOM_LOGO_LIGHT

R3012 10K

MICOM_NON_LOGO_LIGHT

MICOM_GED

R3002 10K

R3000 10K

MICOM_NON_GED

R3007-*2

22K

R3007-*1

56K

MICOM_OLED_FRC

MICOM_OLED_MAIN

MODEL1_OPT_0

MODEL1_OPT_1

MODEL1_OPT_2

MODEL1_OPT_3

MODEL1_OPT_4

MODEL1_OPT_5

MICOM MODEL OPTION

0

MODEL_OPT_0 For LOGO LIGHT

MODEL_OPT_1

MODEL_OPT_2

MODEL_OPT_3

MODEL_OPT_5

NON LOGO

TACT_KEY

LCD / OLED

IR_wafer(12/15)

M13MODEL_OPT_4

NON_GED

1

LOGO

TOUCH_KEY

PDP

IR_wafer(10pin)

H13

GED

Ready for sample set

Need to Assign ADC port

Ready for sample set

P17/TI02/TO02

P51/INTP2/SO11

P50/INTP1/SI11/SDA11

P16/TI01/TO01/INTP5

P13/TXD2/SO20

P14/RXD2/SI20/SDA20

P12/SO00/TXD0/TOOLTXD

P15/PCLBUZ1/SCK20/SCL20

P11/SI00/RXD0/TOOLRXD/SDA00

POWER_DET

POWER_ON/OFF1

WOL/ETH_POWER_ON

LED_R

WOL_CTL

INV_CTL

SOC_RESET

SOC_TX

P146

P147/ANI18

P10/SCK00/SCL00

SOC_RX

AMP_MUTE

CAM_CTL

MODEL1_OPT_5

CAM_CTL

P60/SCLA0 P61/SDAA0

P31/TI03/TO03/INTP4

P75/KR5/INTP9/SCK01/SCL01

P74/KR4/INTP8/SI01/SDA01

P73/KR3/SO01 P72/KR2/SO21

P71/KR1/SI21/SDA21

P70/KR0/SCK21/SCL21

P30/INTP3/RTC1HZ/SCK11/SCL11

1 2

P62

3

P63

4 5 6

R5F100GEAFB#30

7 8 9 10 11 12

13

P50/INTP1/SI11/SDA11

P123/XT1

P137/INTP0

P122/X2/EXCLK

P121/X1

REGC47VSS48VDD

42

43

44

45

46

IC3000-*1

MICOM_LEAD_Cu

14

15

16

17

18

19

P17/TI02/TO02

P13/TXD2/SO20

P51/INTP2/SO11

P16/TI01/TO01/INTP5

P14/RXD2/SI20/SDA20

P15/PCLBUZ1/SCK20/SCL20

P120/ANI19

P41/TI07/TO07

P40/TOOL0

RESET41P124/XT2/EXCLKS

37

38

39

40

P140/PCLBUZ0/INTP6

36

P00/TI00/TXD1

35

P01/TO00/RXD1

34

P130

33

P20/ANI0/AVREFP

32

P21/ANI1/AVREFM

31

P22/ANI2

30

P23/ANI3

29

P24/ANI4

28

P25/ANI5

27

P26/ANI6

26

P27/ANI7

25

20

21

22

23

24

P146

P147/ANI18

P10/SCK00/SCL00

P12/SO00/TXD0/TOOLTXD

P11/SI00/RXD0/TOOLRXD/SDA00

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

NetCast4.0

MICOM (RENESAS)

2013.02.05

30