LG 34UM95-P User Manual

Owner's Manual

IPS LED MONITOR (LED MONITOR)

Please read the safety information carefully before using the product.

IPS LED Monitor (LED Monitor) Model List

34UM95-PD 34UM95-PE

www.lg.com

TABLE OF CONTENTS

3 LICENSE

ENGLISH

4 ASSEMBLING AND

PREPARING

4 Product Composition

5 Product and Button Description

5 - How to Use the Joystick Button

6 - Input Connector

7 Moving and Lifting the

Monitor

8 Installing the Monitor

8 - Assembling the Stand

9 - Detaching the Stand

10 - Installing on a Table

11 - Adjusting the Angle

11 - Tidying up Cables

12 - Installing the Wall Mount Plate

12 - Installing on the Wall

14 - Using the Kensington Lock

19 INSTALLING THE LG

MONITOR SOFTWARE

22 USER SETTINGS

22 Activating the Main Menu

22 - Main Menu Features

23 User Settings

23 - Menu Settings

24 - Ratio

25 - Function

26 - PBP

27 - Picture

28 - Color

29 - Settings

30 - Reset

31 - Reader

32 TROUBLESHOOTING

15 USING THE MONITOR

15 Connecting to a PC

15 - HDMI Connection

16 - DisplayPort Connection

16 - Thunderbolt ( ) Connection

17 Connecting AV Devices

17 - HDMI Connection

17 Connecting Peripherals

17 - USB Cable connection - PC

18 - Connecting Headphones

34 PRODUCT SPECIFICATION

35 Factory Support Mode

(Preset Mode, HDMI/DisplayPort/

Thunderbolt PC)

35 HDMI Timing (Video)

35 Power LED

36 PROPER POSTURE

36 Proper Posture for Using the Monitor

LICENSE

Each model has different licenses. Visit www.lg.com for more information on the license.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

VESA, VESA logo, DisplayPort compliance logo and DisplayPort compliance logo for dual-mode source devices are all registered trademarks of the Video Electronics Standards Association.

ENGLISH

ASSEMBLING AND PREPARING

Product Composition

ENGLISH

Please check whether all the components are included in the box before using the product. If there are any missing components, contact the retailer where you purchased the product. Note that the product and related components may look different from those shown here.

CD (Owner's Manual /

Software) / Guides /

Cards

Power cord AC/DC Adapter HDMI cable

Stand Base Screw Cover

Clear sheet

Two Screws

(M4 x 10)

DisplayPort Cable

(Depending on country)

CAUTION

yAlways use genuine LG components to ensure safety and product performance. yThe product warranty will not cover damage or injury caused by the use of unauthorized components. yIt is recommend that use the supplied components.

NOTE

yThe components may look different from those illustrated here. yWithout prior notice, all product information and specifications contained in this manual are subject to

change to improve the performance of the product.

yTo purchase optional accessories, visit an electronics store or an online shopping site, or contact the

retailer from which you purchased the product.

yThe power cord provided may differ depending upon the region.

ASSEMBLING AND PREPARING

Product and Button Description

Power indicator

yOn Power on yOff Power off

ENGLISH

Joystick Button

How to Use the Joystick Button

You can easily control the functions of the monitor by pressing the joystick button or moving it left/right with your finger.

Basic Functions

Power on

Power off

◄/►

Volume

Control

NOTE

yThe joystick button is located at the bottom of the monitor. yBefore turning on the monitor, please make sure that the DC switch on the rear side of product is On.

(Only 34UM95-PE)

Press the joystick button once with your finger to turn on the monitor.

Press and hold the joystick button once with your finger to turn off the monitor.

You can control the volume by moving the joystick button left/right.

ASSEMBLING AND PREPARING

Input Connector

34UM95-PD

ENGLISH

HDMI IN 2

34UM95-PE

DC-IN

(19 V )

DC-IN

(19 V )

HDMI IN 2

H/P

HDMI IN 1

H/P

HDMI IN 1

DP IN

USB UP

USB IN 1

5 V 1.1 A

USB IN 1

5 V 1.1 A

USB IN 2

5 V 0.5 A

USB IN 2

5 V 0.5 A

USB IN 3

5 V 0.5 A

USB IN 3

5 V 0.5 A

OFF

DC Switch

ASSEMBLING AND PREPARING

Moving and Lifting the Monitor

When moving or lifting the monitor, follow these instructions to prevent the monitor from being scratched or damaged and to ensure safe transportation, regardless of its shape or size.

yPlace the monitor in the original box or pack-

ing material before attempting to move it.

yBefore moving or lifting the monitor, discon-

nect the power cord and all other cables.

yHold the bottom and side of the monitor frame

firmly. Do not hold the panel itself.

yWhen moving the monitor, keep it upright and

never turn the monitor on its side or tilt it sideways.

CAUTION

yAvoid touching the monitor screen as much as

possible.

- This may result in damage to the screen or some of the pixels used to create images.

yIf you use the monitor panel without the stand

base, its joystick button may cause the monitor to become unstable and fall, resulting in damage to the monitor or human injury. In addition, this may cause the joystick button to malfunction.

ENGLISH

yWhen holding the monitor, the screen should

face toward you to prevent it from being scratched.

yWhen transporting the monitor, do not expose

the monitor to shock or excessive vibration.

ASSEMBLING AND PREPARING

Installing the Monitor

Assembling the Stand

Place the screen face down.

ENGLISH

Stand Hinge

CAUTION

yTo protect the screen from scratches, cover

the surface with a soft cloth.

Mount the stand base onto the stand hinge

as shown in the illustration. Fix two screws into the back of the stand base and close the screw cover.

Stand Base

100 mm

Screw Cover

CAUTION

yThe stand height is adjustable by 20 mm yWhen tightening the screws after mounting

the stand base onto the stand hinge, be sure to hold the stand base with your hand. Otherwise, the product may fall, causing personal injury or damage to the product.

yBe careful not to hurt your hand on the edges

of the screw covers.

yApplying excessive force when tightening

screws may cause damage to the monitor. Damage caused in this way will not be covered by the product warranty.

yIf you use the monitor panel without the

stand base, its joystick button may cause the monitor to become unstable and fall, resulting in damage to the monitor or human injury. In addition, this may cause the joystick button to malfunction.

120 mm

Detaching the Stand

Place the screen face down.

CAUTION

yTo protect the screen from scratches, cover

the surface with a soft cloth.

Detach the screw cover from the stand base

as shown in the illustration and then remove the two screws on the back to detach the stand base from the hinge.

Screw Cover

ASSEMBLING AND PREPARING

Stand Base

CAUTION

yIllustrations in this document represent typical

procedures, so they may look different from the actual product.

yDo not carry the monitor upside down by just

holding the base. This may cause the monitor to fall off the stand and could result in personal injury.

yWhen lifting or moving the monitor, do not

touch the monitor screen. The force applied to the monitor screen may cause damage to it.

yIf you use the monitor panel without the stand

base, its joystick button may cause the monitor to become unstable and fall, resulting in damage to the monitor or human injury. In addition, this may cause the joystick button to malfunction.

yWhen removing the screws to detach the

stand base from the hinge, be sure to hold the stand base with your hand. Otherwise, the product may fall, causing personal injury or damage to the product.

ENGLISH

ASSEMBLING AND PREPARING

Installing on a Table

Lift the monitor and place it on the table in an

upright position. Place the monitor at least 10 cm away from the wall to ensure sufficient

ENGLISH

ventilation.

Connect the power adapter to the monitor and

then plug the power cord into the wall outlet.

10 cm

Cautions When Connecting Power Cord

220 V 110 V

yMake sure to use the power cord that is pro-

vided in the product package and connect it to a grounded power outlet.

yIf you need another power cord, please con-

tact your local dealer or the nearest retail store.

Press the joystick button on the bottom of the

monitor to turn on the monitor.

CAUTION

yUnplug the power cord before moving or

installing the monitor. There is risk of electric shock.

yBefore turning on the monitor, please make

sure that the DC switch on the rear side of product is On. (Only 34UM95-PE)

ASSEMBLING AND PREPARING

-515

Adjusting the Angle

Place the monitor mounted on the stand base

in an upright position. Adjust the angle of the screen. The angle of

the screen can be adjusted forward or backward from -5° to 15° for a comfortable viewing experience.

Rear

Front

WARNING

yWhen you adjust the angle, do not hold the

stand as shown on the following illustration. You may injure your fingers.

Tidying up Cables

ENGLISH

Tidy up cables using the cable holder on the stand base as shown in the illustration.

NOTE

yCables can get caught in the hinge area as

shown in the illustration, so be careful when organizing cables.

yBe careful not to touch or press the screen

area when adjusting the angle of the monitor.

ASSEMBLING AND PREPARING

Installing the Wall Mount Plate

This monitor meets the specifications for the wall mount plate or other compatible devices.

Place the screen face down. To protect the

ENGLISH

screen from scratches, cover the surface with a soft cloth.

Attach the clear sheet to the back of the moni-

tor and align it with the screw holes.

Clear sheet (PET sheet)

Place the wall mount plate onto the monitor

and align it with the screw holes. Tighten the four screws to fix the plate to the

monitor using a screwdriver.

Wall mount plate

NOTE

yThe wall mount plate is sold separately. yFor more information on installation, refer to

the wall mount plate's installation guide.

yBe careful not to apply too much force while

mounting the wall mount plate as it may cause damage to the screen

Installing on the Wall

Install the monitor at least 10 cm away from the wall and leave about 10 cm of space at each side of the monitor to ensure sufficient ventilation. Detailed installation instructions can be obtained from your local retail store. Alternatively, please refer to the manual for how to install and set up a tilting wall mounting bracket.

10 cm

To install the monitor to a wall, attach a wall mounting bracket (optional) to the back of the monitor. Make sure that the wall mounting bracket is securely fixed to the monitor and to the wall.

Use the screws and wall mounting bracket that

conform to VESA standards. If you use screws longer than the standard

length, it may damage the inside of the product.

A non-VESA standard screw may damage the

product and cause the monitor to fall. LG Electronics is not liable for any accidents relating to the use of non-standard screws.

VESA compatible only with respect to screw

mounting interface dimensions and mounting screw specifications.

Use the wall mount plate and fixing screws

that conform to VESA standards as specified below.

y784.8 mm or less

* Thickness of the wall mount plate: 2.6 mm * Fixing screw: Diameter 4.0 mm x Pitch

0.7 mm x Length 10 mm

y787.4 mm or more

* Use the wall mount plate and screws that

conform to VESA standards.

10 cm

+ 26 hidden pages