LG 32PC5DVC User Manual

Please read this manual carefully before operating your set.

Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.

PLASMA TV

OWNER’S MANUAL

32PC5DVC

www.lgcommercial.com

As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA).

WARNING / CAUTION

To prevent fire or shock hazards, do not expose this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product

The lightning flash with arrowhead symbol, within an equilateral triangle, is

intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus.

This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled “Important Safety Instructions”. The following safety

instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction:

Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.

When mounting a TV it on the wall, make sure not to install TV by hanging power and signal cables on the back of the TV.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Unplug this apparatus when unused for long periods of time.

Owner Manual

Owner ManualOwner Manual

Owner Manual

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Never touch this apparatus or antenna during a thunder or lighting storm.

Do not allow a impact shock or any objects to fall into the product, and do not drop onto the screen with something.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.

CAUTION concerning the Power Cord : Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use

of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

Outdoor use marking : WARNING - To reduce the risk of fire or elec-

tric shock, do not expose this appliance to rain or moisture.

Wet Location Marking : Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on or over apparatus.

GGRROOUU NNDD IINNGG Ensure that you connect the earth ground wire

to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

DDIISSCC OONNNNEECCTT IINNGG DDEEVVIICCEE FFRROOMM MMAAII NN SS Mains plug is the disconnecting device. The

plug must remain readily operable.

Owner Manual

Power Supply

Short-circuit

Breaker

WARNING / CAUTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

SAFETY INSTRUCTIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . 2

INTRODUCTION

Feature of this TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

PREPARATION

Accessories

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Back Panel Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Back Cover for Wire Arrangement

. . . . . . . . . . . . . . . . . . . . .

Attaching the TV to a Wall

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Use Power Cord Holder

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Production Cover

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Antenna or Cable Connection

. . . . . . . . . . . . . . . . . . . . . . . . . .

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

DVD Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

VCR Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Headphone Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PC Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

WATCHING TV / CHANNEL CONTROL

Remote Control Functions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Turning On TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Channel Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Volume Adjustment

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

On-Screen Menus Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Channel Search

- Auto Scan (Auto Tuning)

. . . . . . . . . . . . . . . . . . . . . . . . . . . 28

- Add / Delete Channel (Manual Tuning)

. . . . . .

- Channel Editing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PICTURE CONTROL

Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 32

Preset Picture Settings

- Picture Mode - Preset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

- Color Tone - Preset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manual Picture Adjustment

- Picture Mode - User Mode

. . . . . . . . . . . . . . . . . . . . . . . . 36

- Color Tone - User Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . .

XD (Picture Improvement Technology)

. . . . . . . . . . . . .

Advanced - Black (Darkness) Level

. . . . . . . . . . . . . . . . . . . 39

Image Sticking Minimization (ISM) Method

. . . . . . 40

Low-Power Picture Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Picture Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

SOUND & LANGUAGE CONTROL

Preset Sound Setting (Sound Mode)

. . . . . . . . . . . . . . . . 43

Sound Setting Adjustment - User Mode

. . . . . . . . . . .44

Balance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Stereo/SAP Broadcasts Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . 46

Audio Language

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

On-Screen Menus Language Selection

. . . . . . . . . . . . .

Caption Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

- Analog Broadcasting System Captions

. . . . . . . 50

- Digital Broadcasting System Captions

. . . . . . . .

- Caption Option

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TIME SETTING

Clock Setting

- Auto Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Auto On/Off Time Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Sleep Time Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Auto Shut-off Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

PARENTAL CONTROL / RATINGS

Set Password & Lock System

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Movie & TV Rating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

APPENDIX

Troubleshooting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Product Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

External Control Through RS-232C

. . . . . . . . . . . . . . . . . .

FEATURE OF THIS TV

INTRODUCTION

LG's own special digital image generator, consisting of a full digital image processor, six different main picture quality factors.

HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing."

PREPARATION

ACCESSORIES

Ensure that the following accessories are included with your product. If an accessory is missing, please contact the dealer where you purchased the product.

User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard compliance for the product.

1.5V 1.5V

Owner’s Manual CD Manual

123

456

T E

D J

U S

F A

S O

U N

T I

E R

U T

123

456

V O

E R

A C

T E

D J

U S

I T

S A

F A

P I C

T U

R E

O U

T I

E R

I N

Remote Control,

Batteries

Power Cord

Protection Cover

(Refer to p.11)

OOppttiioonn EExxttrraass

Power Cord Holder

(Refer to p.11)

4-Bolts for stand assembly

(Refer to p.10)

* Slightly wipe stained spot on the exterior only with the polishing

cloth for the product exterior if there is stain or fingerprint on surface of the exterior.

* Do not wipe roughly when removing stain. Please be cautions of that

excessive pressure may cause scratch or discoloration.

Polishing Cloth

D-sub 15 pin Cable

75ohm Round Cable

PREPARATION

FRONT PANEL INFORMATION

PREPARATION

■

Here shown may be somewhat different from your TV.

■

NOTE: If your product has a protection tape attached, remove the tape. And then wipe the product with a cloth (If a polishing cloth is included with your product, use it).

Power/Standby Indicator

Illuminates red in standby mode. Illuminates green when the set is

switched on.

Remote Control Sensor

POWER Button

INPUT Button

MENU Button

ENTER Button

VOLUME (

FF,GG

)Buttons

CHANNEL (

EE,DD

)Buttons

INPUT

ENTER

VOL

PREPARATION

BACK PANEL INFORMATION

■

Here shown may be somewhat different from your TV.

ANTENNA/CABLE IN

Connect over-the air signals to this jack. Connect cable signals to this jack.

RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC.

RGB IN (PC)

Connect the output from a PC.

AUDIO IN (RGB/DVI)

Connect the audio from a PC.

COMPONENT IN

Connect a component video/audio device to these jacks.

EXCLUSIVE SERVICE

AV IN (Audio/Video)

Connect audio/video output from an external device to these jacks.

HEADPHONE INPUT

Plug the headphone into the headphone socket.

HDMI/DVI IN

Connect a HDMI signal to this jack. Or DVI (Video) signal to this jack with a HDMI to

DVI cable.

Power Cord Socket

For operation with AC power. Caution: Never attempt to operate the TV on DC

power.

ANTENNA/CABLE

EXCLUSIVE

SERVICE

AV IN

HEADPHONE

COMPONENT IN

RGB IN

(PC)

RS-232C IN

(CONTROL & SERVICE)

AUDIO IN

(RGB/DVI)

HDMI/DVI

2 3 4

38 67

PREPARATION

STAND INSTALLATION

PREPARATION

■

Here shown may be somewhat different from your TV.

Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage.

Assemble the product stand with the product as shown.

Install the 4 bolts securely, in the back of the product in the holes provided.

BACK COVER FOR WIRE ARRANGEMENT

Arrange the cables as shown picture.

PREPARATION

ATTACHING THE TV TO A WALL

■

Here shown may be somewhat different from your TV.

After connecting the power cord to the AC input terminal, remove the bolt at the hole on the back cover and fix the power cord at the rear side of the TV by using the bracket for fixing the power cord.

USE POWER CORD HOLDER

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.

■

Insert the eye-bolts or TV brackets and bolts to tighten the product to the wall as shown in the picture.

*If your product has the bolts in the eye-bolts position before inserting the bolts, loosen the bolts.

Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■

Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.

■

You should purchase necessary components to prevent TV from falling off of the stand.

■

Here shown may be somewhat different from your TV.

PREPARATION

DESKTOP PEDESTAL INSTALLATION

PREPARATION

For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.

Ensure adequate ventilation by following the clearance recommendations.

CAUTION

4 inches

PROTECTION COVER

When installing the wall-mounted unit, use the protection cover for desk-type stand installation.

PREPARATION

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.

For optimum picture quality, adjust antenna direction if needed.

2. Cable

Wa ll Antenna Socket

Outdoor Antenna (VHF, UHF)

Cable TV Wall Jack

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

RF Coaxial Wire (75 ohm)

Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

Be careful not to bend the bronze wire when connecting the antenna.

Copper Wire

ANTENNA/CABLE

The TV will let you know when the analog, cable, and digital channel scans are complete.

NOTE

■

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■

If the antenna is not installed properly, contact your dealer for assistance.

Antenna

UHF

Signal Amplifier

VHF

EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

EXTERNAL EQUIPMENT SETUP

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

EXCLUSIVE

SERVICE

AV IN

HEADPHONE

COMPONENT IN

Y L RPB PR

When connecting Component cable

1. How to connect

Connect the video outputs (Y, P

B, P

)

of the digital set

top box to the

CCOOMMPPOO NN EENNTT IINN

((

YY ,, PP

,, PP

))

jacks

on the set. Match the jack colors (Y = green, P

= blue, and PR = red).

Connect the audio output of the digital set-top box to the

CCOOMMPPOO NN EENNTT IINN

((

LL,, RR

))

jacks on the set.

2. How to use

■

Turn on the digital set-top box. (

Refer to the owner’s manual for the digital set-top box. operation

)

■

Select

CCoo mmpp oo nneenntt

input source by using the

IINNPPUU TT

button on the remote control.

Signal

480i

480p

720p

10 8 0 i

Component

Yes

HDMI

Yes

Y, C

B/P

B, C

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

15.73 59.94

15.73 60.00

31.47 59.94

31.50 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

Resolution

720x480i

720x480p

1280x720p

1920x1080i

■

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

EXTERNAL EQUIPMENT SETUP

When connecting HDMI cable

Connect the digital set-top box to

HHDDMMII //DDVVII IINN

jack on the set.

No separated audio connection is necessary. HDMI supports both audio and video.

1. How to connect

2. How to use

■

Turn on the digital set-top box. (

Refer to the owner’s manual for the digital set-top box.

)

■

Select

HHDD MMII

input source by using the

IINN PPUUTT

button

on the remote control.

RGB IN

(PC)

RS-232C IN

(CONTROL & SERVICE)

AUDIO IN

(RGB/DVI)

HDMI/DVI

HDMI-DTV OUTPUT

HDMI/DVI-DTV mode

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.47 59.94

31.47 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

Resolution

720x480p

1280x720p

1920x1080i

EXTERNAL EQUIPMENT SETUP

When connecting HDMI to DVI cable

ANTENNA/CABLE

EXCLUSIVE

SERVICE

AV IN

HEADPHONE

COMPONENT IN

RGB IN

(PC)

RS-232C IN

(CONTROL & SERVICE)

AUDIO IN

(RGB/DVI)

HDMI/DVI

L R

DVI-DTV OUTPUT

Connect the DVI output of the digital set-top box to the

HHDDMMII//DD VVII IINN

jack on the set.

Connect the audio output of the digital set-top box to the

AAUUDDIIOO IINN ((RR GGBB //DDVVII

))

jack on the set.

1. How to connect

■

Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.

)

■

Select

HHDD MMII

input source by using the

IINNPPUU TT

button on the remote control.

2. How to use

EXTERNAL EQUIPMENT SETUP

DVD SETUP

When connecting Component cable

EXCLUSIVE

SERVICE

AV IN

HEADPHONE

COMPONENT IN

GB IN (PC)

Y L RPB PR

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV

YPBP

Video output ports

on DVD player

B-Y

R-Y

Connect the video outputs (Y, P

B, P

)

of the DVD to the

CCOOMMPPOO NNEE NN TT IINN

((

YY ,, PP

,, PP

))

jacks on the set.

Match the jack colors (

Y = green, P

B = blue, and P

R = red

)

Connect the audio outputs of the DVD to the CCOOMMPPOO NNEE NN TT IINN

((

LL,, RR

))

jacks on the set.

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select

CCoo mmpp oo nneenntt

input source by using the

IINNPPUU TT

button on the remote control.

■

Refer to the DVD player's manual for operating instructions.

EXTERNAL EQUIPMENT SETUP

ANTENNA/CABLE

RGB IN

(PC)

RS-232C IN

(CONTROL & SERVICE)

AUDIO IN

(RGB/DVI)

HDMI/DVI

HDMI-DVD OUTPUT

When connecting HDMI cable

Connect the HDMI output of the DVD to the HHDDMMII//DD VVII IINN

jack on the set.

No separated audio connection is necessary. HDMI supports both audio and video.

1. How to connect

2. How to use

■

Select

HHDD MMII

input source by using the

IINN PPUU TT

button

on the remote control.

■

Refer to the DVD player's manual for operating instructions.

EXTERNAL EQUIPMENT SETUP

VCR SETUP

When connecting with an antenna

■

To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

■

If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all manufactures and in consequence the manufactures warranty does not cover the product bearing this phenomenon.

ANTENNA/CABLE

RGB IN

(PC)

RS-232C IN

(CONTROL & SERVICE)

AUDIO IN

(RGB/DVI)

HDMI/DVI

L R

S-VIDEOVIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

Wall Jack

Antenna

Connect the RF antenna out socket of the VCR to the

AANN TTEENNNNAA//CCAABBLL EE IINN

socket on the set.

Connect the antenna cable to the RF antenna in socket of the VCR.

1. How to connect

■

Set VCR output switch to 3 or 4 and then tune TV to the same channel number.

■

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.

)

2. How to use

EXTERNAL EQUIPMENT SETUP

HEADPHONE SETUP

When connecting with a RCA cable

EXCLUSIVE

SERVICE

AV IN

HEADPHONE

COMPONENT IN

L R

S-VIDEO VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

Connect the

AA UUDDII OO/VV IIDDEEOO

jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.

)

■

Select

AA VV

input source by using the

IINNPPUU TT

button on the

remote control.

If you have a mono VCR, connect the audio cable from the VCR to the

AAUUDDIIOO LL//MMOONNOO

jack of the set.

NOTE

You can listen to the sound through the headphone.

Plug the headphone into the headphone socket.

To adjust the headphone volume, press the

VVOOLL

+ or

- button. If you press the

MMUUTTEE

button, the sound

from the headphone is switched off.

1. How to connect

EXCLUSIVE

SERVICE

AV IN

HEADPHONE

COMPONENT IN

EXTERNAL EQUIPMENT SETUP

PC SETUP

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

When connecting D-sub 15pin cable

RGB IN

(PC)

RS-232C IN

(CONTROL & SERVICE)

AUDIO IN

(RGB/DVI)

HDMI/DVI

AUDIO

RGB OUTPUT

Connect the RGB output of the PC to the

RR GGBB IINN

((

PP CC

))

jack on the set.

Connect the PC audio output to the

AAUUDDIIOO IINN

((

RR GGBB //DD VVII

))

jack on the set.

1. How to connect

2. How to use

■

Turn on the PC and the TV.

■

Select

RR GGBB--PPCC

input source by using the

IINNPPUU TT

button

on the remote control.

When connecting HDMI to DVI cable

Connect the DVI output of the PC to the

HHDDMMII// DDVVII

II NN

jack on the set.

Connect the PC audio output to the

AAUUDDIIOO IINN

((

RR GGBB //DD VVII

))

jack on the set.

1. How to connect

2. How to use

■

Turn on the PC and the TV.

■

Select

HHDD MMII

input source by using the

IINNPPUU TT

button on

the remote control.

AUDIO

HEAD

RGB IN

(PC)

RS-232C IN

(CONTROL & SERVICE)

AUDIO IN

(RGB/DVI)

HDMI/DVI

DVI-PC OUTPUT AUDIO

+ 53 hidden pages

LG 32PC5DVC User Manual

WARNING / CAUTION

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

CONTENTS

INTRODUCTION

PREPARATION

ACCESSORIES

FRONT PANEL INFORMATION

BACK PANEL INFORMATION

STAND INSTALLATION

BACK COVER FOR WIRE ARRANGEMENT

ATTACHING THE TV TO A WALL

USE POWER CORD HOLDER

DESKTOP PEDESTAL INSTALLATION

PROTECTION COVER

ANTENNA OR CABLE CONNECTION

EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

When connecting Component cable

When connecting HDMI cable

When connecting HDMI to DVI cable

DVD SETUP

When connecting Component cable

When connecting HDMI cable

VCR SETUP

When connecting with an antenna

HEADPHONE SETUP

When connecting with a RCA cable

PC SETUP

When connecting D-sub 15pin cable

When connecting HDMI to DVI cable