LG 20M44A-B User guide

<![if ! IE]>

<![endif]>ENGLISH

OWNER’S MANUAL

LED LCD MONITOR

Please read this manual carefully before operating your set and retain it for future reference.

LED LCD MONITOR MODEL

19M44A 19M44D 20M44A 20M44D

www.lg.com

<![if ! IE]>

<![endif]>ENGLISH

2 TABLE OF CONTENTS

CONTENTS

	3	ASSEMBLING AND PREPAR-		22	TROUBLESHOOTING
		ING		24
	3	Unpacking			SPECIFICATIONS‌
	4	Parts and buttons
			24		19M44A
	5	Moving and Lifting the Monitor
	6	Setting up the Monitor set	25		19M44D
	6	- Attaching the Stand Base	26		20M44A
	6	- Detaching the Stand Base	28		20M44D
	7	- Mounting on a table	30		Preset Modes (Resolution)
	7	- Using the cable holder	30		Indicator
	9	- Mounting on a wall		31
	10 USING THE MONITOR SET				PROPER POSTURE
			31		Proper posture for using the Monitor set.
	10 Connecting to a PC
	10	- D-SUB connection
	10	- DVI-D connection

12 CUSTOMIZING SETTINGS

13Customizing Settings

13- Menu Settings

14-Picture

15-Color

16-Display

17-Others

18READER Setting

19FUNC. Setting

19-SUPER ENERGY SAVING

20-Picture Mode

21-DUAL DISPLAY

21 -DUAL WEB

ASSEMBLING AND PREPARING 3

ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.

<![if ! IE]>

<![endif]>ENGLISH

CD(Owner's Manual) /	D-SUB Cable
Card

Power Cord AC-DC Adapter

( Depending on the country )

Stand Body

CAUTION

DVI-D Cable

(This cable is not included in all countries.)

(19M44D/20M44D)

or

AC-DC Adapter

( Depending on the country )

Stand Base

yyDo not use any unapproved accessories to ensure the safety and product life span.

yyAny damages or injuries by using unapproved accessories are not covered by the warranty.

NOTE

yyThe accessories supplied with your product may vary depending on the model.

yyProduct specifications or contents in this manual may be changed without prior notice due to upgrade of product functions.

4 ASSEMBLING AND PREPARING

Parts and buttons

<![if ! IE]>

<![endif]>ENGLISH

Power Indicator yyLighting On: Turned on yyLighting Off: Turned off

(Power Button)

Button (See p.12)

Connection panel (See p.10)

	ASSEMBLING AND PREPARING 5
Moving and Lifting the Monitor	yyWhen holding the monitor, the screen should
When moving or lifting the monitor, follow these	face away from you to prevent it being
instructions to prevent the monitor from being	scratched.
scratched or damaged and to ensure safe trans-
portation regardless of its shape or size.
yyIt is advisable to place the monitor in the
original box or packing material before at-
tempting to move it.
yyBefore moving or lifting the monitor, discon-
nect the power cord and all cables.
yyHold the top and bottom of the monitor frame	yyWhen moving the monitor, avoid any strong
firmly. Do not hold the panel itself.	shock or vibrations to the product.
	yyWhen moving the monitor, keep it upright,
	never turn the monitor on its side or tilt it
	sideways.

CAUTION

yyAs far as possible, avoid touching the monitor screen. This may result in damage to the screen or some of the pixels used to create images.

<![if ! IE]>

<![endif]>ENGLISH

6 ASSEMBLING AND PREPARING

<![if ! IE]>

<![endif]>ENGLISH

Setting up the Monitor set

Attaching the Stand Base

1Place the Monitor set with the screen side down on a flat and cushioned surface.

CAUTION

Lay a foam mat or soft protective cloth on the surface to protect the screen from damage.

21 Attach the Stand Body to the monitor set.

2 Attach the Stand Base.

3 Tighten the screw to the right.

Stand Body

Stand Base

Detaching the Stand Base

1Place the Monitor set with the screen side down on a flat and cushioned surface.

21 Pull out the Stand Body and Stand Base from the monitor set.

2Turn the screw to the left.

3Pull out the Stand Base.

Stand Body

Stand Base

Stand Body

Stand Base

CAUTION

yyThis illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture.

yyDo not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot.

	ASSEMBLING AND PREPARING 7
Mounting on a table	3 Press (Power) button on the bottom switch
	panel to turn the power on.
1 Lift and tilt the Monitor set into its upright
position on a table.
Leave a 10 cm (minimum) space from the wall
for proper ventilation.	CAUTION

10 cm

10 cm

10 cm

10 cm

Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur.

Using the cable holder

<![if ! IE]>

<![endif]>ENGLISH

2 Connect the AC-DC Adapter and Power Cord to a wall outlet.

Cable holder

or

<![if ! IE]>

<![endif]>ENGLISH

8 ASSEMBLING AND PREPARING

WARNING

Using the Kensington security system

When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the

Do

Do not hold this set like below picture.Monitor screen can detach from stand base and injure your body.

The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit http://www.kensington.com.

Connect the Kensington security system cable between the Monitor set and a table.

NOTE

The Kensington security system is optional. You can obtain it from most electronics stores.

+20 to -3 degrees up or down to adjust the angle of the Monitor set to suit your view.

Front

Rear

ASSEMBLING AND PREPARING 9

Mounting on a wall

For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.

Model
		19M44A		20M44A
						<![if ! IE]> <![endif]>ENGLISH
		19M44D		20M44D
VESA (A x B)	75 x 75
Standard	M4
screw
Number of	4
screws

10 cm

10 cm

10 cm

10 cm

If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set.

When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.

1Please, Use the screw and wall mount interface in accordance with VESA Standards.

2If you use screw longer than standard, the monitor might be damaged internally.

3If you use improper screw, the product might be damaged and drop from mounted position. In

this case, LG Electronics is not responsible for it.

4VESA compatible only with respect to screw mounting interface dimensions and mounting

screw specifications.

5 Please use VESA standard as below. yy784.8 mm (30.9 inch) and under

*Wall Mount Pad Thickness : 2.6 mm

* Screw : Φ 4.0 mm x Pitch 0.7 mm x

Length 10 mm

yy787.4 mm (31.0 inch) and above

*Please use VESA standard wall mount pad and screws.

CAUTION

yyDisconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur.

yyIf you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury.

yyUse only an authorized LG wall mount and contact the local dealer or qualified personnel.

yyDo not over tighten the screws as this may cause damage to the Monitor set and void your warranty.

yyUse only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.

yyScrew length from outer surface of back cover should be under 8mm.

Wall mount Pad

Back Cover

Wall mount Pad

Back Cover

Standard screw

Max.8mm

NOTE

yyUse the screws that are listed on the VESA standard screw specifications.

yyThe wall mount kit will include an installation manual and necessary parts.

yyThe wall mount bracket is optional. You can obtain additional accessories from your local dealer.

yyThe length of screws may differ depending on the wall mount. Be sure to use the proper length.

yyFor more information, refer to the instructions supplied with the wall mount.

<![if ! IE]>

<![endif]>ENGLISH

10 USING THE MONITOR SET

USING THE MONITOR SET

Connecting to a PC

yyYour Monitor set supports Plug & Play*.

*Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention.

D-SUB connection

Transmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations.

NOTE

yyWhen using a D-Sub signal input cable connector for Macintosh

yyMac adapter

For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector.

DVI-D connection

Transmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the following illustrations.