<![endif]>ENGLISH
LED LCD MONITOR
Please read this manual carefully before operating your set and retain it for future reference.
LED LCD MONITOR MODEL
20M35PD
www.lg.com
<![endif]>ENGLISH
2 TABLE OF CONTENTS
3 |
ASSEMBLING AND PREPAR- |
23 |
SPECIFICATIONS |
||
|
ING |
|
|
|
|
|
23 |
20M35PD |
|||
3 |
Unpacking |
||||
24 |
Preset Modes (Resolution) |
||||
4 |
Parts and buttons |
24 |
Indicator |
5Setting up the Monitor set
5 |
- Attaching the Stand Base |
25 |
PROPER POSTURE |
|
5 |
- Detaching the stand base |
|||
25 |
Proper posture for using the Monitor set. |
|||
6 |
- Detaching the stand body |
7- Mounting on a table
7- Adjusting the angle
8- Adjusting the stand height
8- Using the Kensington locking device 9 - Using the Pivot function
10 - Mounting on a wall
11 USING THE MONITOR SET
11 Connecting to a PC
11 - D-SUB connection
11 - DVI-D connection
13 CUSTOMIZING SETTINGS
14Customizing Settings
14- Menu Settings
15-Picture
16-Color
17-Display
18-Others
19READER Setting
20-SUPER ENERGY SAVING
21 TROUBLESHOOTING
ASSEMBLING AND PREPARING 3
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.
<![endif]>ENGLISH
CD(Owner's Manual) /
Card
Power Cord
CAUTION
D-SUB Cable
(This cable is not included in all countries.)
Stand Base
DVI-D Cable
(This cable is not included in all countries.)
yyDo not use any unapproved accessories to ensure the safety and product life span.
yyAny damages or injuries by using unapproved accessories are not covered by the warranty.
NOTE
yyThe accessories supplied with your product may vary depending on the model.
yyProduct specifications or contents in this manual may be changed without prior notice due to upgrade of product functions.
4 ASSEMBLING AND PREPARING
<![endif]>ENGLISH
Power Indicator yyLED On : Power is on yyLED Off: Power is off
(Power Button)
Front Side Buttons
Input Connectors (See p. )
ASSEMBLING AND PREPARING 5
1Place the Monitor set with the screen side down on a flat and cushioned surface.
Caution
yyTo protect the screen from scratches, cover the surface with a soft cloth.
2Check the position (at the front and rear) of the stand body, then mount the stand base on the stand body as shown in the figure.
Stand Body
Stand Base
3Using a coin, turn the screw clockwise to secure the stand base.
Stand Base
1Place the monitor's screen face down.
To protect the screen from scratches, cover the surface with a soft cloth.
2Using a coin, turn the screw in the stand base counterclockwise. Detach the stand base from the stand body.
Stand Body
Stand Base
Caution
yyThe components appearing in the illustrations may look different from the actual product.
yyDo not carry the monitor upside-down as this may cause it to fall off its stand, resulting in damage or injury.
yyTo avoid damaging the screen when lifting or moving the monitor, only hold the stand or the plastic cover. This avoids putting unnecessary pressure on the screen.
yyOnly remove the tape and the locking pin when the monitor is mounted on the stand base and is in an upright position. Otherwise, the stand body may protrude, which may lead to injury.
<![endif]>ENGLISH
6 ASSEMBLING AND PREPARING
<![if ! IE]> <![endif]>ENGLISH |
1 |
Place the monitor's screen face down. To |
|
||
|
|
protect the screen from scratches, cover the |
|
|
surface with a soft cloth. |
|
2 |
Using a screwdriver, remove the four screws |
|
|
and detach the stand from the monitor. |
ASSEMBLING AND PREPARING 7
1Lift the monitor and place it on the table in an upright position.
Install at least 10 cm away from the wall to ensure sufficient ventilation.
10 cm
10 cm
10 cm
10 cm
1Place the monitor mounted on the stand base in an upright position.
2Adjust the angle of the screen. The angle of the screen can be adjusted up to 5° forwards and 20° backwards for a comfortable viewing experience.
Rear Side |
Front Side |
<![endif]>ENGLISH
2Connect the Power cord to the monitor, then plug the power cord into the wall outlet.
WARNING
yyTo avoid injury to the fingers when adjusting the screen, do not hold the lower part of the monitor's frame as illustrated below.
3Press the (Power) button on the front of the monitor to turn on the monitor.
CAUTION
yyUnplug the power cord prior to moving or installing the monitor. There is risk of electric shock.
yyBe careful not to touch or press the screen area when adjusting the angle of the monitor.
<![endif]>ENGLISH
8 ASSEMBLING AND PREPARING
1Place the monitor mounted on the stand base in an upright position.
2Remove the tape attached at the bottom rear of the stand body, then pull out the locking pin.
Stand Body
Tape
Locking Pin
3 The height can be adjusted up to 110 mm.
110.0mm
CAUTION
yyOnce the pin is removed, it is not necessary to re-insert it to adjust the height.
WARNING
yyDo not put your finger between the screen and the base (chassis) when adjusting the screen's height.
The connector for the Kensington lock is located on the rear of the monitor.
For more information on installation and usage, refer to the Kensington lock user manual or visit the website at http://www.kensington.com.
Connect the monitor to the table with the Kensington lock cable.
NOTE
yyUsing the Kensington lock is optional. The accessories can be purchased at your local electronics store.