Lexibook SM1120 User Manual

Congratulations on your purchase of this weather station, MeteoClock SM1120. Please take the time to read and understand this manual so you can begin to enjoy the convenience and features this product has to offer.

What exactly is a W

eather Station?

Lexibook digital stations measure not only the time in progress - thanks to their built-in clock - but also the actual weather!

The MeteoClock SM1120 incorporates different functions:

- Thermometer: Temperature is displayed in real time to the nearest tenth of a degree Celsius. Thanks to its wireless sensor, the station can sense from a distance the outside temperature or that of another room!

- Hygrometer: Outdoor hygrometry is expressed in percentage of humidity in the ambient air. The ideal “Comfort” Zone for the human body ranges from 35 to 65% hygrometry for a given temperature in between 18 and 24ºC.

INTRODUCTION

Wireless Weather Station

SM1120 + ASM20 - Owners manual

FEATURES

Main Display Unit SM1120:

■ 12/ 24 hour clock and alarm

■ Auto synchronising radio controlled clock

(DCF-77)

■ local temperature display

■ receives and displays temperature and

humidity readings from up to 4 remote transmitter via RF technology of 433MHz

■ minimum and maximum temperature record

■ high/ low temperature alarm function

■ temperature and humidity trend indicator

■ weather report symbols

■ LED Backlight

■ user-selectable °C or °F

■ battery type: 2 x AA

Remote Sensor ASM20:

■ drip-proof design with LCD

■ temperature display in user-selectable

°C or °F

■ humidity display

■ transmission range: up to 40 meters in

open area

■ battery type: 2 x AA

Button placement

CHANNEL: scrolls through remote channels 1-4

ALARM/AM/PM/°C/°F: toggles between °C and °F, 12 and 24 hour

format, turns alarm on/off; clears temperature alarm

presets MODE/SNOOZE: scrolls through time, alarm and temperature alarm set points (high/low); activates alarm snooze UP/HOUR/MAX: scrolls through hours; shows maximum temperature; enables and disables backlight

DOWN/MINUTE/MIN: scrolls through minutes; show minimum

temperature

Table Stand

SET: enter to House code and Channel setting modex

°C/°F: change between °C or °F, change channel and

house code

Battery compartment

LCD display

Wall Mount Holder & Table Stand

GETTING STARTED

Battery installation

remove battery cover

2 AA size batteries (SM1120)

2 AA size batteries (ASM20)

Insert between terminals observing proper polarity then replace cover

LOW BA

TTERY INDICATION: Low battery indication will be flashing low battery indicator (for both

indoor & outdoor). On transmitter, will be displayed.

Setting remote transmitters

Insert batteries to start setup

HOUSE CODE will flash for 8 seconds

Select HOUSE CODE (1-15) by pressing °C/°F and then press SET

Transmitters for each receiver must be set to the same HOUSE CODE and pressing SET

CHANNEL will flash for 8 seconds

Select CHANNEL(1-4) by pressing °C/°F and then press SET

Humidity & Temperature will display

Select °C or °F of Temperature by pressing °C/°F key

* Use a different house code if your weather station detecTs other signals from

neighboring sources

* Factory default: house code = 01 and channel = 01

GETTING STARTED

SYNCHRONIZATION

Automatic Learn Function

Learn function executes automatically and runs for

approximately 3 minutes when batteries are first

installed in the receiver. Within these 3 minutes, receiver picks up the temperature & humidity signals from remote transmitter and displays the readings.

Manual-Learn (Searching for Remote Signals)

If a new remote transmitter is added or if signal is lost (outdoor display blinking), learn function must be executed again.

Press & hold ALARM/AM/PM/°C/°F for 3 seconds to start.

Beep sound indicates that learn function has started.

CHANNEL symbol will flash and unit will beep as each transmitter is

detected.

Temperature & humidity readings of remote transmitter displays on the

receiver.

Press & hold Channel for 3 seconds to start auto channel scroll function. In this mode, the display will scroll through the data from all the valid channels, each of which will be shown for 8 seconds. Press & hold Channel for 3 seconds again to disable this function.

SETUP

Clock setting;

Modes are arranged in a circular pattern starting with clock:

Press and hold MODE/SNOOZE until time flashes.

Select hour using UP/HOUR/MAX.

Select minute using DOWN/MINUTE/MIN.

Press ALARM/PM/AM/°C/°F to toggle between 12 or 24 hour format.

Alarm setting:

Select alarm mode using MODE/SNOOZE.

Select hour using UP/HOUR/MAX.

Select minute using DOWN/MINUTE/MIN.

In alarm mode, press ALARM to toggle alarm On and Off.

When alarm sounds, will flash .

Press MODE/SNOOZE to snooze the alarm for 5 minutes. After

that the alarm will sound again.

Press ANY other key will shut off the alarm.

Without

interruption, alarm will shut off automatically after one minute.

CLOCK & ALARM SETTING

Check Local Temperature

Local temperature displays instantly after batteries are inserted.

Check Remote Temperature & Humidity

Press CHANNEL to toggle between Channel 1, 2, 3 and 4. Temperature and humidity readings will

alternately display on the receiver.

°C or °F Temperature Display

Toggle between °C and °F by pressing ALARM/PM/AM/°C/°F in clock mode.

Min and Max Temperature

Press DOWN/MINUTE/MIN in Clock mode to display

minimum temperature record.

Press UP/HOUR/MAX in Clock mode to display

maximum temperature record.

Note:

Min/Max temperature records are automatically cleared daily at 00:00.

WEATHER DISPLAY

Temperature & humidity trend

The trend indicator shows the trend of temperature and humidity determined by the particular transmitter in the past half-hour interval.

eather report symbols

The receiver is able to monitor and display the weather status based on collected data from Channel 1.

About Freeze Warning

* Snow symbol will flash to warn of 'snowing'. * Activated when Channel 1's temperature is between -1.9 °C and +2.9 °C. * Snow will appear solid if and when Channel 1's temperature falls below -1.9 °C: it is freezing.

Note:

* Initially, the weather will be cloudy * Remote transmitter Channel 1 will be used for weather indication. * If Channel 1 is empty, then weather will always be cloudy. * If Channel 1 has no humidity data, weather indication will always be cloudy, but freeze warning

and snow indication will be available.

WEATHER DISPLAY

The temperature alarm function allows you to have an alarm sound if the temperature rises above or drops below a particular set point.

High temperature alarm

Scroll to high temperature alarm mode using MODE/SNOOZE..

and or existing preset will flash.

Select channel (1, 2, 3, 4 or local) using CHANNEL.

Press + or - key to set the high temperature limit value.

To disable particular alarm, press ALARM/PM/AM/°C/°F

; dashes = alarm disabled.

Press MODE/SNOOZE to finish.

Repeat steps to for all other channels if desired.

Low temperature alarm

Scroll to high temperature alarm mode using MODE/SNOOZE..

and or existing preset will flash.

Select channel (1, 2, 3, 4 or local) using CHANNEL.

Press + or - key to set the low temperature limit value.

To disable particular alarm, press ALARM/PM/AM/°C/°F

; dashes = alarm disabled.

Press MODE/SNOOZE to finish.

Repeat steps to for all other channels if desired.

TEMPERATURE ALARM

Once the high/low temperature alarm is set for a particular channel, and/or will appear on display for that channel

When alarm sounds, the sounding channel is displayed, and or flashes to indicate whether it is the high or low temperature alarm. Press any button to shut off alarm.

To clear high/low temperature alarm

Select high/low temperature alarm set point using MODE/SNOOZE..

Press ALARM/PM/AM/°C/°F to clear value.

Press MODE/SNOOZE to finish setting.

To view maximum temperature

Toggle between current and maximum temperature using UP/HOUR/MAX.

Press CHANNEL to view the maximum temperature for other channels.

Pour voir la température minimum

Toggle between current and maximum temperature using

DOWN/MINUTE/MIN.

Press CHANNEL to view the maximum temperature for other channels.

OTHER FEATURES

MODE/SNOOZE

TROUBLESHOOTING

Solution:

Re-synchronize receiver by holding ALARM/PM/AM/°C/°F for 3 seconds until a beep is heard.

Ensure the remote transmitter is out of direct sunlight, and away from sources of heat.

Repeat the learning procedures.

- Temperature may be below -30°C.

- Batteries in remote transmitter may need

changing.

- Move remote transmitter closer to the receiver.

- Make sure remote transmitter is away from

sources of electrical disturbance.

Problem:

The temperature measurement of remote transmitter and receiver does not match.

Temperature reading of the outdoor remote transmitter seems too high.

Receiv er

is no longe r receiving remote transmitter signals or temperature display reads Lo.

Additional sensor :

Mesure temperature and hygrometry in other places!

- upstairs

- in the baby's bedroom

- in the basement

- in the garden

- in another room

To order: 0808 100 3015

or www.lexibook.com

This product is covered by our two-year warranty.

To make use of the warranty or the after-sales service, please contact your retailer and supply proof of purchase. Our warranty covers material or installation-related defects attributable to the manufacturer, with the exception of wear caused by failure to respect the instructions for use or any unauthorised work on the equipment (such as dismantling, exposure to heat or damp, etc.).

For technical assistance call 0808 100 3015 Web: http://www.lexibook.co.uk Email: infouk@lexibook.com

WARRANTY

ACCESSORIES

Lexibook SM1120 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual