Leuze Xenon 1900, Xenon 1900h, Xenon 1902, Xenon 1902h, Xenon 1902g-BF Operating Instructions
...
Xenon™/Granit™
Xenon 1900, 1900h, 1902, 1902h, 1902g-BF
Granit 1910i, 1911i, 1980i, 1981i, 1920i
Area-Imaging Scanners
User Guide
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in
this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes
have been made. The information in this publication does not represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of this material. HII disclaims all responsibility for the selection and use of software and/or hardware to achieve intended results.
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII.
2010-2018 Honeywell International Inc. All rights reserved.
Microsof
registered trademarks of Microsoft Corporation.
The Bluetooth
Apple is a trademark of Apple Inc., registered in the U.S. and other countries.
Other product names or marks mentioned in this document may be trademarks or registered trademarks of other compa-
nies and are the property of their respective owners.
For patent information, refer to www.hsmpats.com.
®
Windows®, Windows NT®, Windows 2000, Windows ME, Windows XP, and the Windows logo are trademarks or
t
®
word mark and logos are owned by Bluetooth SIG, Inc.
TABLE OF CONTENTS
Customer Support ..................................................................................................................... xvii
Technical Assistance .......................................................................................................... xvii
Product Service and Repair ............................................................................................. xvii
Limited Warranty ................................................................................................................. xvii
Send Feedback .....................................................................................................................xvii
Chapter 1 - Get Started ....................................................................................1
About This Manual......................................................................................................................... 1
Unpack Your Device....................................................................................................................... 1
Connect the Device........................................................................................................................ 1
Connect with USB....................................................................................................................1
Connect with Keyboard Wedge .......................................................................................... 4
Connect with RS232 Serial Port ........................................................................................ 6
Connect with RS485............................................................................................................... 9
Mount a CCB01-010BT Charge Base................................................................................. 10
Mount a CCB02-100BT/CCB05-100BT Base ................................................................. 10
Reading Techniques................................................................................................................... 12
Xenon 1900/1902 and Granit 1910i/1911i ............................................................. 12
Granit 1980i/1981i..............................................................................................................12
Granit 1920i DPM Scanner .............................................................................................. 13
Menu Bar Code Security Settings......................................................................................... 13
Set Custom Defaults .................................................................................................................. 14
Reset the Custom Defaults...................................................................................................... 14
Xenon/Granit User Guide i
Chapter 2 - Program the Interface.............................................................. 17
Introduction ...................................................................................................................................17
Program the Interface - Plug and Play ...............................................................................17
Keyboard Wedge ..........................................................................................................................17
Laptop Direct Connect ..............................................................................................................18
RS232 Serial Port.........................................................................................................................18
RS485...............................................................................................................................................18
RS485 Packet Mode.............................................................................................................19
USB IBM SurePos ........................................................................................................................20
USB PC or Macintosh Keyboard ............................................................................................20
USB HID........................................................................................................................................... 21
USB Serial .......................................................................................................................................21
CTS/RTS Emulation .............................................................................................................21
ACK/NAK Mode......................................................................................................................22
Remote MasterMind™ for USB............................................................................................... 22
Verifone® Ruby Terminal............................................................................................................22
Gilbarco® Terminal.......................................................................................................................23
Honeywell Bioptic Aux Port .....................................................................................................23
Datalogic™ Magellan® Aux Port..............................................................................................23
NCR Bioptic Aux Port..................................................................................................................24
Wincor Nixdorf Terminal...........................................................................................................24
Wincor Nixdorf Beetle™ Terminal.......................................................................................... 24
Wincor Nixdorf RS232 Mode A...............................................................................................25
Pair with a Honeywell Vehicle Mount Computer.............................................................25
Keyboard Country Layout.........................................................................................................25
Keyboard Wedge Modifiers......................................................................................................33
ALT Mode..................................................................................................................................33
Keyboard Style........................................................................................................................33
Keyboard Conversion...........................................................................................................34
Control Character Output..................................................................................................35
Keyboard Modifiers ..............................................................................................................35
ii Xenon/Granit User Guide
RS232 Modifiers...........................................................................................................................37
RS232 Baud Rate...................................................................................................................37
RS232 Word Length: Data Bits, Stop Bits, and Parity.............................................38
RS232 Receiver Time-Out..................................................................................................39
RS232 Handshake ................................................................................................................39
RS232 Timeout.......................................................................................................................40
XON/XOFF ...............................................................................................................................40
ACK/NAK...................................................................................................................................40
Scanner to Bioptic Communication .....................................................................................41
Scanner-Bioptic Packet Mode..........................................................................................41
Scanner-Bioptic ACK/NAK Mode....................................................................................41
Scanner-Bioptic ACK/NAK Timeout ..............................................................................42
Chapter 3 - Cordless System Operation:
Xenon 1902g/1912 and Granit 1911i/1981i.........................................43
How the Cordless Charge Base/Access Point Works.....................................................43
Link the Scanner to a Charge Base.......................................................................................43
Link the Scanner to an Access Point....................................................................................44
Replace a Linked Scanner ........................................................................................................45
Communication Between the Cordless System
and the Host...................................................................................................................................45
Program the Scanner and Base or Access Point .............................................................46
RF (Radio Frequency) Module Operation...........................................................................46
System Conditions.......................................................................................................................46
Page Button....................................................................................................................................47
Page Button and Presentation Modes ................................................................................48
Temporary Streaming Presentation Timeout.............................................................49
About the Battery .........................................................................................................................49
Charge Information ..............................................................................................................49
Battery Recommendations................................................................................................50
Safety Precautions for Lithium Batteries.....................................................................50
Proper Disposal of the Battery .........................................................................................50
Beeper and LED Sequences and Meaning........................................................................51
Xenon/Granit User Guide iii
Scanner LED Sequences and Meaning .......................................................................51
Base/Access Point LED Sequences and Meaning...................................................51
Base Power Communication Indicator......................................................................... 52
Reset Scanner ............................................................................................................................... 52
Scan While in Base Cradle........................................................................................................52
Base Charge Modes....................................................................................................................53
Page ..................................................................................................................................................54
Page Mode ...............................................................................................................................54
Page Pitch ................................................................................................................................ 54
Error Indicators.............................................................................................................................55
Beeper Pitch - Base Error...................................................................................................55
Number of Beeps - Base Error .........................................................................................55
Scanner Report.............................................................................................................................56
Scanner Address ..........................................................................................................................56
Base or Access Point Address ................................................................................................. 56
Scanner Modes.............................................................................................................................56
Charge Only Mode ................................................................................................................56
Charge and Link Mode........................................................................................................ 57
Linked Modes .........................................................................................................................57
Unlink the Scanner......................................................................................................................58
Override Locked Scanner...................................................................................................58
Out-of-Range Alarm...................................................................................................................58
Alarm Sound Type ................................................................................................................. 59
Scanner Power Time-Out Timer.............................................................................................60
Flexible Power Management...................................................................................................61
Batch Mode....................................................................................................................................62
Batch Mode Beep.................................................................................................................. 63
Batch Mode Storage ............................................................................................................63
Batch Mode Quantity...........................................................................................................64
Enter Quantities.....................................................................................................................64
Batch Mode Output Order.................................................................................................66
Total Records...........................................................................................................................66
Delete Last Code ...................................................................................................................66
iv Xenon/Granit User Guide
Clear All Codes........................................................................................................................66
Transmit Records to Host...................................................................................................67
Batch Mode Transmit Delay ..............................................................................................67
Multiple Scanner Operation ....................................................................................................67
Scanner Name...............................................................................................................................68
Application Work Groups ..........................................................................................................69
Application Work Group Selection..................................................................................70
Reset the Factory Defaults: All Application Work Groups ............................................70
Reset the Custom Defaults: All Application Work Groups ...........................................71
Use the Scanner with Bluetooth Devices............................................................................71
Bluetooth Secure Simple Pairing (SSP)........................................................................71
Bluetooth HID Keyboard Connect...................................................................................72
Virtual Keyboard.....................................................................................................................74
Bluetooth HID Keyboard Disconnect.............................................................................74
Bluetooth Serial Port - PCs/Laptops.............................................................................74
PDAs/Mobility Systems Devices .....................................................................................74
Change the Scanner’s Bluetooth PIN Code................................................................75
Minimize Bluetooth/ISM Band Network Activity ............................................................75
Auto Reconnect Mode .........................................................................................................75
Trigger Reconnect Mode.....................................................................................................76
Maximum Link Attempts ....................................................................................................76
Relink Time-Out .....................................................................................................................77
Bluetooth/ISM Network Activity Examples.................................................................77
Host Acknowledgment...............................................................................................................78
Host ACK On/Off ...................................................................................................................80
Host ACK Timeout .................................................................................................................80
Host ACK Responses............................................................................................................80
Chapter 4 - Cordless System Operation: Xenon 1902g-BF...................81
How the CCB01-010BT-07N-BF Cordless Charge Base Works ...............................81
Link the Scanner to a Charge Base.......................................................................................82
Replace a Linked Scanner ........................................................................................................82
Communication Between the Cordless System
and the Host...................................................................................................................................83
Xenon/Granit User Guide v
Program the Scanner and Base ............................................................................................. 83
RF (Radio Frequency) Module Operation ..........................................................................83
System Conditions ......................................................................................................................84
About the Instant Charge Pack ..............................................................................................85
Charge Information..............................................................................................................85
Beeper and LED Sequences and Meaning........................................................................85
Scanner .....................................................................................................................................86
Low Power Alerts..........................................................................................................................86
Low Power Alert Range .......................................................................................................87
Low Power Alert Flash Number .......................................................................................87
Low Power Alert Repeat ......................................................................................................87
Low Power Alert Beep ..........................................................................................................88
Base................................................................................................................................................... 88
Base Communication and Scanning ............................................................................88
Base Charge Status..............................................................................................................89
Base Power Communication Indicator......................................................................... 89
Reset Scanner ............................................................................................................................... 89
Base Charge Modes....................................................................................................................89
Page Button with Scanner Out of the Base.......................................................................90
Page Button with Scanner in the Base................................................................................91
Temporary Streaming Presentation Timeout.............................................................91
Scan While in Base Cradle........................................................................................................91
Paging ..............................................................................................................................................92
Page Mode ...............................................................................................................................92
Page Pitch ................................................................................................................................ 92
Linking Sound...............................................................................................................................93
Error Indicators.............................................................................................................................93
Beeper Pitch - Base Error...................................................................................................93
Number of Beeps - Base Error .........................................................................................94
Scanner Report.............................................................................................................................94
Scanner Address ..........................................................................................................................94
Base Address .................................................................................................................................94
vi Xenon/Granit User Guide
Scanner Modes .............................................................................................................................95
Charge Only Mode ................................................................................................................95
Charge and Link Mode........................................................................................................95
Linked Modes..........................................................................................................................95
Unlink the Scanner......................................................................................................................96
Override Locked Scanner ...................................................................................................97
Out-of-Range Alarm ...................................................................................................................97
Alarm Sound Type .................................................................................................................97
Scanner Power Time-Out Timer.............................................................................................98
Flexible Power Management...................................................................................................99
Batch Mode .................................................................................................................................100
Batch Mode Beep ...............................................................................................................101
Batch Mode Storage..........................................................................................................101
Batch Mode Quantity........................................................................................................102
Enter Quantities..................................................................................................................102
Batch Mode Output Order ..............................................................................................104
Total Records........................................................................................................................104
Delete Last Code.................................................................................................................105
Clear All Codes.....................................................................................................................105
Transmit Records to Host................................................................................................105
Batch Mode Transmit Delay ...........................................................................................105
Scanner Name............................................................................................................................106
Change the Scanner’s Bluetooth PIN Code.............................................................107
Minimize Bluetooth/ISM Band Network Activity .........................................................107
Auto Reconnect Mode ......................................................................................................108
Maximum Link Attempts .................................................................................................108
Relink Time-Out ..................................................................................................................109
Bluetooth/ISM Network Activity Examples..............................................................109
Host Acknowledgment............................................................................................................110
Host ACK On/Off ................................................................................................................111
Host ACK Timeout ..............................................................................................................112
Host ACK Responses.........................................................................................................112
Xenon/Granit User Guide vii
Chapter 5 - Input/Output Settings...........................................................113
Power Up Beeper....................................................................................................................... 113
Beep on BEL Character .......................................................................................................... 114
Trigger Click ................................................................................................................................ 114
Good Read and Error Indicators ......................................................................................... 114
Beeper – Good Read.......................................................................................................... 114
Beeper Volume – Good Read ......................................................................................... 115
Beeper Pitch – Good Read.............................................................................................. 115
Vibrate – Good Read.......................................................................................................... 115
Beeper Pitch – Error .......................................................................................................... 116
Beeper Duration – Good Read....................................................................................... 117
LED – Good Read ...............................................................................................................117
Number of Beeps – Good Read..................................................................................... 117
Number of Beeps – Error................................................................................................. 117
Beeper Volume Max .......................................................................................................... 118
Good Read Delay ................................................................................................................ 118
User-Specified Good Read Delay................................................................................. 119
Trigger Modes ............................................................................................................................ 119
Manual Trigger .................................................................................................................... 119
Trigger Toggle...................................................................................................................... 119
Serial Trigger ........................................................................................................................ 121
Read Time-Out .................................................................................................................... 121
Presentation Mode................................................................................................................... 122
Presentation LED Behavior after Decode................................................................. 122
Presentation Sensitivity................................................................................................... 122
Presentation Centering.................................................................................................... 123
In-Stand Sensor Mode............................................................................................................ 124
Poor Quality Codes................................................................................................................... 125
Poor Quality 1D Codes..................................................................................................... 125
Poor Quality PDF Codes .................................................................................................. 126
Low Resolution PDF Codes............................................................................................ 126
CodeGate®.................................................................................................................................... 127
Streaming Presentation™ Mode ......................................................................................... 127
viii Xenon/Granit User Guide
Streaming Presentation In-Stand................................................................................128
Mobile Phone Read Mode .....................................................................................................128
Hands Free Time-Out..............................................................................................................128
Reread Delay ............................................................................................................................... 129
User-Specified Reread Delay ......................................................................................... 129
2D Reread Delay .................................................................................................................129
Character Activation ................................................................................................................130
Activation Character..........................................................................................................130
End Character Activation After Good Read ..............................................................131
Character Activation Timeout........................................................................................131
Character Deactivation...........................................................................................................131
Deactivation Character ....................................................................................................132
Illumination Lights...................................................................................................................132
Aimer Delay..................................................................................................................................132
User-Specified Aimer Delay............................................................................................133
Active Aimer.................................................................................................................................133
Aimer Mode .................................................................................................................................133
Laser Aimer - Scan Duration ................................................................................................134
Centering......................................................................................................................................134
Single Code Centering......................................................................................................134
Custom Centering ..............................................................................................................135
Preferred Symbology ...............................................................................................................136
High Priority Symbology..................................................................................................137
Low Priority Symbology ...................................................................................................137
Preferred Symbology Time-out.....................................................................................137
Preferred Symbology Default ........................................................................................138
Output Sequence Overview...................................................................................................138
Output Sequence Editor ..................................................................................................138
To Add an Output Sequence...........................................................................................138
Output Sequence Editor Commands................................................................................139
Enter Output Sequence..........................................................................................................142
Partial Sequence.................................................................................................................142
Good Read Tone - Output Sequences ........................................................................145
Xenon/Granit User Guide ix
Multiple Symbols ...................................................................................................................... 145
No Read ........................................................................................................................................ 146
Video Reverse ............................................................................................................................. 146
Working Orientation ................................................................................................................ 147
Chapter 6 - Healthcare Settings................................................................149
Quiet Operations - Combination Codes .......................................................................... 149
Silent Mode with Flashing LED .................................................................................... 149
Silent Mode with Long LED ...........................................................................................150
Very Low Beeper (Nighttime Mode)............................................................................ 150
Low Beeper (Daytime Mode) ......................................................................................... 151
Quiet Operations - LED and Volume Settings .............................................................. 151
Linking LED Colors and Sound .................................................................................... 151
Number of LED Flashes .................................................................................................. 152
LED Flash Rate.................................................................................................................... 152
LED Solid (No Flash)......................................................................................................... 153
Page Volume Control........................................................................................................ 153
Out-of-Range Alarm Volume......................................................................................... 154
Out-of-Range Delay.......................................................................................................... 155
Chapter 7 - Direct Part Mark (DPM) Settings.........................................157
DPM Illumination Settings ...................................................................................................157
Cycle Illumination .............................................................................................................. 157
Low Contrast Codes .......................................................................................................... 157
Direct Illumination - Top and Bottom ........................................................................ 158
Direct Illumination - Bottom.......................................................................................... 158
Indirect Illumination ......................................................................................................... 158
Low Contrast Data Matrix Enhancements ..................................................................... 158
Chapter 8 - Data Edit ...................................................................................161
Prefix/Suffix Overview ............................................................................................................ 161
Points to Keep In Mind..................................................................................................... 161
Add a Prefix or Suffix:........................................................................................................ 162
Example: Add a Tab Suffix to All Symbologies........................................................ 162
x Xenon/Granit User Guide
Clear One or All Prefixes or Suffixes............................................................................162
Add a Carriage Return Suffix to All Symbologies...................................................163
Prefix Selections........................................................................................................................163
Suffix Selections........................................................................................................................163
Function Code Transmit.........................................................................................................164
Intercharacter, Interfunction, and Intermessage Delays ..........................................164
Intercharacter Delay..........................................................................................................164
User Specified Intercharacter Delay ...........................................................................165
Interfunction Delay ............................................................................................................ 165
Intermessage Delay...........................................................................................................166
Chapter 9 - Data Format .............................................................................167
Data Format Editor Introduction ........................................................................................167
Show Data Format ....................................................................................................................168
Add a Data Format....................................................................................................................168
Other Programming Selections....................................................................................169
Terminal ID Table................................................................................................................170
Data Format Editor Commands..........................................................................................170
Send Commands ................................................................................................................170
Move Commands................................................................................................................176
Search Commands.............................................................................................................177
Miscellaneous Commands .............................................................................................180
Data Formatter...........................................................................................................................183
Data Format Non-Match Error Tone...........................................................................184
Primary/Alternate Data Formats ........................................................................................185
Single Scan Data Format Change................................................................................185
Chapter 10 - Symbologies..........................................................................187
All Symbologies..........................................................................................................................188
Message Length Description...............................................................................................188
Codabar.........................................................................................................................................188
Code 39 ......................................................................................................................................... 191
Interleaved 2 of 5.......................................................................................................................194
Xenon/Granit User Guide xi
NEC 2 of 5.................................................................................................................................... 195
Code 93......................................................................................................................................... 197
Straight 2 of 5 Industrial (three-bar start/stop)........................................................... 198
Straight 2 of 5 IATA (two-bar start/stop)......................................................................... 199
Matrix 2 of 5................................................................................................................................ 200
Code 11......................................................................................................................................... 201
Code 128...................................................................................................................................... 202
ISBT 128 Concatenation ................................................................................................. 202
GS1-128 ....................................................................................................................................... 204
Telepen.......................................................................................................................................... 205
UPC-A............................................................................................................................................ 206
UPC-A/EAN-13 with Extended Coupon Code.............................................................. 209
Coupon GS1 DataBar Output .............................................................................................. 210
UPC-E0 ......................................................................................................................................... 210
UPC-E1 ......................................................................................................................................... 213
EAN/JAN-13 ............................................................................................................................... 213
ISBN Translate..................................................................................................................... 215
EAN/JAN-8.................................................................................................................................. 216
MSI.................................................................................................................................................. 218
GS1 DataBar Omnidirectional............................................................................................. 220
GS1 DataBar Limited .............................................................................................................. 220
GS1 DataBar Expanded ......................................................................................................... 221
Trioptic Code............................................................................................................................... 221
Codablock A ................................................................................................................................222
Codablock F ................................................................................................................................223
Label Code................................................................................................................................... 223
PDF417......................................................................................................................................... 224
MacroPDF417............................................................................................................................ 225
MicroPDF417............................................................................................................................. 225
GS1 Composite Codes ............................................................................................................ 226
GS1 Emulation........................................................................................................................... 227
xii Xenon/Granit User Guide
TCIF Linked Code 39 (TLC39)..............................................................................................228
QR Code ........................................................................................................................................228
Data Matrix ..................................................................................................................................230
MaxiCode......................................................................................................................................231
Aztec Code ...................................................................................................................................232
Chinese Sensible (Han Xin) Code.......................................................................................233
Postal Codes - 2D......................................................................................................................234
Planet Code Check Digit..................................................................................................237
Postnet Check Digit...........................................................................................................238
Australian Post Interpretation.......................................................................................238
Postal Codes - Linear ..............................................................................................................239
China Post (Hong Kong 2 of 5)......................................................................................239
Korea Post..............................................................................................................................240
Chapter 11 - Imaging Commands.............................................................241
Single-Use Basis .......................................................................................................................241
Command Syntax......................................................................................................................241
Image Snap - IMGSNP............................................................................................................242
IMGSNP Modifiers .............................................................................................................242
Image Ship - IMGSHP .............................................................................................................245
IMGSHP Modifiers .............................................................................................................246
Image Size Compatibility.................................................................................................254
Intelligent Signature Capture - IMGBOX.........................................................................255
Signature Capture Optimize ..........................................................................................255
IMGBOX Modifiers .............................................................................................................256
RF Default Imaging Device ...................................................................................................260
Chapter 12 - Utilities...................................................................................261
To Add a Test Code I.D. Prefix to All Symbologies.........................................................261
Show Decoder Revision ..........................................................................................................261
Show Scan Driver Revision....................................................................................................261
Show Software Revision .........................................................................................................262
Test Menu.....................................................................................................................................262
Xenon/Granit User Guide xiii
TotalFreedom.............................................................................................................................. 262
Application Plug-Ins (Apps) ................................................................................................. 263
EZConfig Cloud for Scanning Introduction ................................................................... 263
EZConfig Cloud for Scanning Operations................................................................ 264
Install EZConfig Cloud for Scanning.......................................................................... 264
Reset the Factory Defaults.................................................................................................... 264
Chapter 13 - Serial Programming Commands.......................................267
Conventions................................................................................................................................ 267
Menu Command Syntax ........................................................................................................267
Query Commands..................................................................................................................... 268
Trigger Commands................................................................................................................... 270
Reset the Custom Defaults ................................................................................................... 271
Menu Commands ..................................................................................................................... 272
Chapter 14 - Product Specifications........................................................305
Xenon 1900/1900h Corded Scanner Product Specifications ...............................305
Xenon 1902/1902h/1912 Cordless Scanner Product Specifications ...............306
Xenon 1902g-BF Scanner Product Specifications..................................................... 308
Granit 1910i Industrial Corded Scanner Product Specifications.......................... 309
Granit 1911i Industrial Cordless Scanner Product Specifications....................... 310
Granit 1980i Industrial Full Range Corded Scanner
Product Specifications ........................................................................................................... 311
Granit 1981i Industrial Full Range Cordless Scanner
Product Specifications ........................................................................................................... 312
Granit 1920i Industrial DPM Scanner Product Specifications .............................. 314
CCB01-010BT Charge Base Product Specifications ................................................. 315
CCB01-010BT-07N-BF Charge Base Product Specifications ............................... 316
CCB02-100BT/CCB05-100BT Industrial Charge Base
Product Specifications ........................................................................................................... 317
Depth of Field Charts .............................................................................................................. 318
Xenon B&W Scanner Typical Performance.............................................................. 318
Xenon B&W Scanner Guaranteed Performance.................................................... 319
xiv Xenon/Granit User Guide
Xenon Color Scanner (Model COL) Typical Performance..................................319
Xenon Color Scanner (Model COL) Guaranteed Performance ........................320
Granit 1910i/1911i Scanner Typical Performance .............................................. 320
Granit 1910i/1911i Scanner Guaranteed Performance ....................................321
Granit 1980i/1981i Scanner Typical Performance (200 lux)...........................321
Granit 1980i/1981i Scanner Guaranteed Performance (200 lux).................322
Granit 1920i Typical Performance...............................................................................323
Granit 1920i Guaranteed Performance.....................................................................323
Standard Connector Pinouts................................................................................................324
Keyboard Wedge .................................................................................................................324
Serial Output ........................................................................................................................324
RS485 Output ......................................................................................................................325
USB...........................................................................................................................................325
Required Safety Labels...........................................................................................................326
Xenon 1900/1902 Scanner ...........................................................................................326
CCB01-010BT/CCB01-010BT-07N-BF Base.........................................................327
Granit 1910i/1911i/1920i/1980i/1981i Scanner...............................................328
CCB02-100BT/CCB05-100BT Base...........................................................................329
Chapter 15 - Maintenance and Troubleshooting .................................. 331
Repairs...........................................................................................................................................331
Maintenance...............................................................................................................................331
Clean the Scanner..............................................................................................................331
Clean the Window...............................................................................................................331
Health Care Housing.........................................................................................................332
Inspect Cords and Connectors......................................................................................332
Replace Cables in Corded Scanners .................................................................................332
Replace a Xenon Interface Cable .................................................................................333
Replace a Granit Interface Cable .................................................................................333
Replace Cables and Batteries in Cordless Systems....................................................333
Replace an Interface Cable in a Base .........................................................................333
Change a Xenon Scanner Battery................................................................................334
Change a Granit Scanner Battery ................................................................................335
Troubleshoot a Corded Scanner..........................................................................................335
Xenon/Granit User Guide xv
Troubleshoot a Cordless System ........................................................................................ 336
Troubleshoot a Base.......................................................................................................... 336
Troubleshoot a Cordless Scanner................................................................................ 336
Chapter A - Reference Charts ....................................................................339
Symbology Charts ....................................................................................................................339
Linear Symbologies........................................................................................................... 339
2D Symbologies.................................................................................................................. 340
Postal Symbologies........................................................................................................... 341
ASCII Conversion Chart (Code Page 1252).................................................................... 342
Lower ASCII Reference Table ............................................................................................... 343
ISO 2022/ISO 646 Character Replacements................................................................ 346
Keyboard Key References ...................................................................................................... 349
Sample Symbols............................................................................................351
Programming Chart......................................................................................353
xvi Xenon/Granit User Guide
Customer Support
Technical Assistance
To search our knowledge base for a solution or to log in to the Technical Support
portal and report a problem, go to www.hsmcontactsupport.com.
For our latest contact information, see www.honeywellaidc.com/locations.
Product Service and Repair
Honeywell International Inc. provides service for all of its products through service
centers throughout the world. To obtain warranty or non-warranty service, return
your product to Honeywell (postage paid) with a copy of the dated purchase
record. To learn more, go to www.honeywellaidc.com and select Service & Repair at
the bottom of the page.
Note: The following paragraph is used only in Mobility User Guides:
For ongoing and future product quality improvement initiatives, the terminal
comes equipped with an embedded device lifetime counter function. Honeywell
may use the lifetime counter data for future statistical reliability analysis as well as
ongoing quality, repair and service purposes.
Limited Warranty
For warranty information, go to www.honeywellaidc.com and click Get Resources >
Product Warranty.
Xenon/Granit User Guide xvii
xviii Xenon/Granit User Guide
CHAPTER
1
GET STARTED
About This Manual
This User Guide provides installation and programming instructions for the
Xenon™ 1900 corded area-imaging scanners, the Xenon 1902 cordless area-imaging scanners, the Granit 1910i and 1980i corded industrial scanners, and the
Granit 1911i and 1981i cordless industrial scanners. Product specifications,
dimensions, warranty, and customer support information are also included.
Honeywell bar code scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide.
An asterisk (*) next to an option indicates the default setting.
Unpack Your Device
After you open the shipping carton containing the product, take the following
steps:
• Check for damage during shipment. Report damage immediately to the carrier
who delivered the carton.
• Make sure the items in the carton match your order.
• Save the shipping container for later storage or shipping.
Connect the Device
Connect with USB
A scanner or a cordless base can be connected to the USB port of a computer.
Xenon/Granit User Guide 1
1. Connect the appropriate interface cable to the device first, then to the com-
Corded Xenon Scanner USB Connection:
Corded Granit Scanner USB Connection:
puter.
.
2 Xenon/Granit User Guide
2. If you are connecting a Granit scanner, make sure the cable is pushed tightly
CCB01-010BT/CCB01-010BT-07N-BF Base USB Connection:
CCB02-100BT/CCB05-100BT Base USB Connection:
into the scanner. Loosen the locking plate and slide it over the base of the cable
connector to lock the cable in place. Tighten the screw.
Note: The power supply must be ordered separately, if needed.
3. If you are connecting a CCB01-010BT or CCB01-010BT-07N-BF Base, make
sure the cables are secured in the wireways in the bottom of the cordless base
and the base sits flat on a horizontal surface. If you are connecting a CCB02100BT or CCB05-100BT Base, see Mount a CCB02-100BT/CCB05-100BT
Base on page 10.
4. The scanner beeps.
5. Verify the scanner or cordless base operation by scanning a bar code from the
Sample Symbols, beginning on page 351.
Xenon/Granit User Guide 3
The unit defaults to a USB PC Keyboard. Refer to page 20 for other USB terminal
Corded Xenon Scanner Keyboard Wedge Connection:
settings.
For additional USB programming and technical information, refer to “USB Application Note,” available at www.honeywellaidc.com.
Connect with Keyboard Wedge
A scanner or cordless base can be connected between the keyboard and PC as a
“keyboard wedge,” where the scanner provides data output that is similar to keyboard entries.
Note: The Granit 1980i does not support the keyboard wedge interface.
The following is an example of a keyboard wedge connection:
1. Turn off power and disconnect the keyboard cable from the back of the terminal/computer.
2. Connect the appropriate interface cable to the device and to the terminal/
computer.
4 Xenon/Granit User Guide
3. If you are connecting a Granit scanner, make sure the cable is pushed tightly
Corded Granit Scanner Keyboard Wedge Connection:
CCB01-010BT/CCB01-010BT-07N-BF Base Keyboard Wedge Connection:
into the scanner. Loosen the locking plate and slide it over the base of the cable
connector to lock the cable in place. Tighten the screw.
Xenon/Granit User Guide 5
Note: The power supply must be ordered separately, if needed.
CCB02-100BT/CCB05-100BT Base Keyboard Wedge Connection:
4. If you are connecting a CCB01-010BT or CCB01-010BT-07N-BF Base, make
sure the cables are secured in the wireways in the bottom of the cordless base
and the base sits flat on a horizontal surface. If you are connecting a CCB02100BT or CCB05-100BT Base, see Mount a CCB02-100BT/CCB05-100BT
Base on page 10.
5. Turn the terminal/computer power back on. The scanner beeps.
6. Verify the scanner or cordless base operation by scanning a bar code from the
Sample Symbols, beginning on page 351. The scanner beeps once. If using a
Granit scanner, it also vibrates.
The unit defaults to an IBM PC AT and compatibles keyboard wedge interface with
a USA keyboard. A carriage return (CR) suffix is added to bar code data.
Connect with RS232 Serial Port
1. Turn off power to the terminal/computer.
2. Connect the appropriate interface cable to the scanner.
Note: For the scanner or cordless base to work properly, you must have the correct cable for
your type of terminal/computer.
6 Xenon/Granit User Guide
Corded Xenon Scanner RS232 Serial Port Connection:
Corded Granit Scanner RS232 Serial Port Connection:
Xenon/Granit User Guide 7
3. If you are connecting a Granit scanner, make sure the cable is pushed tightly
CCB01-010BT/CCB01-010BT-07N-BF Base RS232 Serial Port Connection:
CCB02-100BT/CCB05/100BT Base RS232 Serial Port Connection:
into the scanner. Loosen the locking plate and slide it over the base of the cable
connector to lock the cable in place. Tighten the screw.
Note: The power supply must be ordered separately, if needed.
4. If you are connecting a CCB01-010BTor CCB01-010BT-07N-BF Base, make
sure the cables are secured in the wireways in the bottom of the cordless base
and the base sits flat on a horizontal surface. If you are connecting a CCB02100BT or CCB05-100BT Base, see Mount a CCB02-100BT/CCB05-100BT
Base on page 10.
5. Plug the serial connector into the serial port on your computer. Tighten the two
screws to secure the connector to the port.
6. Once the scanner or cordless base has been fully connected, power up the
computer.
This interface programs 115,200 baud, 8 data bits, no parity, and 1 stop bit.
8 Xenon/Granit User Guide
Connect with RS485
Corded Xenon Scanner RS485 Connection:
CCB01-010BT/CCB01-010BT-07N-BF Base RS485 Connection:
A Xenon scanner or cordless base can be connected for an IBM POS terminal interface. (This interface is not available in the Granit devices.)
1. Connect the appropriate interface cable to the device, then to the computer.
Note: The power supply must be ordered separately, if needed.
2. Make sure the cables are secured in the wireways in the bottom of the cordless
base and the base sits flat on a horizontal surface.
Xenon/Granit User Guide 9
3. Turn the terminal/computer power back on. The scanner beeps.
4. Verify the scanner or cordless base operation by scanning a bar code from the
Sample Symbols, beginning on page 351. The scanner beeps once. If using a
Granit scanner, it also vibrates.
For further RS485 settings, refer to RS485,page 18.
Mount a CCB01-010BT Charge Base
8x32 thread
x .39 in. (10mm) deep
2.36 in.
59.84mm
3.35 in.
85.09mm
2.8 in.
72.1mm
Mount a CCB02-100BT/CCB05-100BT Base
The CCB02-100BT or CCB05-100BT Base can be mounted on either a horizontal
or vertical surface. The cables can be routed through either the top or the bottom
of the base.
The cables can be routed down through the bottom of the base, securing the
cables in the wireways.
The cables can also be routed up through the top of the base, crossing them over
and securing the cables in the wireways.
When routing the cables up through the top of the base, be sure to cross the cables
over before placing in the wireways. If not, too much strain is placed on the cable
connectors.
10 Xenon/Granit User Guide
When mounted on a vertical surface, a locking system is used to secure the scan-
Locked position
for vertical mount
Unlocked position
for horizontal mount
2 in.
51.17mm
5.31 in.
134.92mm
2.51 in.
63.7mm
2.36 in.
60mm
.84 in.
21.42mm
ner when it is in the stand. When mounted on a horizontal surface, the locking
mechanism should be set to unlocked (pushed up). When mounted on a vertical
surface, the locking mechanism should be set to locked (pushed down).
Use 30mm screws, appropriate for the mounting surface material, to mount the
base securely.
Xenon/Granit User Guide 11
Reading Techniques
Linear bar codes with
aiming beam
2D Matrix symbol
with aiming beam
Linear bar codes with
aiming pattern
2D Matrix symbol
with aiming pattern
Xenon 1900/1902 and Granit 1910i/1911i
The Xenon 1900/1902 scanners have a view finder that projects a bright red aiming beam that corresponds to the scanner’s horizontal field of view. The Granit
1910i/1911i scanners have an aiming pattern. The aiming beam or pattern should
be centered over the bar code, but it can be positioned in any direction for a good
read.
Granit 1980i/1981i
The Granit 1980i/1981i scanners use a laser aimer (red dot) and a red LED (red
box) to locate bar codes. Use the red LED when scanning at a near distance (less
than 11.8 inches / 30 cm) and center the box over the bar code. The laser aimer
(red dot) appears to the right of the center of the bar code. Use the laser aimer (red
dot) when scanning at a far distance (up to 50 feet / 15.2 meters) and aim at the
12 Xenon/Granit User Guide
center of the bar code. At far distances the red box may not be apparent. For both
Near distance scanning
less than 11.8 in/30 cm
Far distance scanning
up to 50 ft/15.2 m
near distance and far distance, the aimers can be positioned in any direction for a
good read.
Granit 1920i DPM Scanner
The Granit 1920i scanner uses a red aiming dot to locate bar codes. Center the
aimer on the bar code.
The aiming beam or pattern is smaller when the scanner is closer to the code and
larger when it is farther from the code. Symbologies with smaller bars or elements
(mil size) should be read closer to the unit. Symbologies with larger bars or elements (mil size) should be read farther from the unit. To read single or multiple
symbols (on a page or on an object), hold the scanner at an appropriate distance
from the target, pull the trigger, and center the aiming beam or pattern on the symbol. If the code being scanned is highly reflective (e.g., laminated), it may be necessary to tilt the code up 15° to 18° to prevent unwanted reflection.
Menu Bar Code Security Settings
Honeywell scanners are programmed by scanning menu bar codes or by sending
serial commands to the scanner. If you want to restrict the ability to scan menu
codes, you can use the Menu Bar Code Security settings. Contact the nearest technical support office (see Technical Assistance on page xvii) for further information.
Xenon/Granit User Guide 13
Set Custom Defaults
Set Custom Defaults
Save Custom Defaults
You have the ability to create a set of menu commands as your own, custom
defaults. To do so, scan the Set Custom Defaults bar code below before scanning
the menu commands for your custom defaults. If a menu command requires scanning numeric codes from the Programming Chart, beginning on page 353, then a
Save code, that entire sequence will be saved to your custom defaults. When you
have entered all the commands you want to save for your custom defaults, scan the
Save Custom Defaults bar code.
Note: When using a cordless system, the Custom Defaults settings apply to all workgroups.
Scanning the Save Defaults bar code also causes both the scanner and the base or
Access Point to perform a reset and become unlinked. The scanner must be placed in
its base to re-establish the link before any setup codes are entered. If using an Access
Point, the linking bar code must be scanned. See Cordless System Operation: Xenon
1902g/1912 and Granit 1911i/1981i beginning on page 43,or Cordless System
Operation: Xenon 1902g-BF beginning on page 81 for additional information.
You may have a series of custom settings and want to correct a single setting. To do
so, just scan the new setting to overwrite the old one. For example, if you had previously saved the setting for Beeper Volume at Low to your custom defaults, and
decide you want the beeper volume set to High, just scan the Set Custom Defaults
bar code, then scan the Beeper Volume High menu code, and then Save Custom
Defaults. The rest of the custom defaults will remain, but the beeper volume setting will be updated.
Reset the Custom Defaults
If you want the custom default settings restored to your scanner, scan the Activate
Custom Defaults bar code below. This is the recommended default bar code for
most users. It resets the scanner to the custom default settings. If there are no cus-
14 Xenon/Granit User Guide
tom defaults, it will reset the scanner to the factory default settings. Any settings
Activate Custom Defaults
that have not been specified through the custom defaults will be defaulted to the
factory default settings.
Note: If using a cordless system, scanning this bar code also causes both the scanner and
the base or Access Point to perform a reset and become unlinked. The scanner must
be placed in its base to re-establish the link. If using an Access Point, the linking bar
code must be scanned. See Cordless System Operation: Xenon 1902g/1912 and
Granit 1911i/1981i beginning on page 43,or Cordless System Operation: Xenon
1902g-BF beginning on page 81 for additional information.
Xenon/Granit User Guide 15
16 Xenon/Granit User Guide
CHAPTER
2
PROGRAM THE INTERFACE
IBM PC AT and Compatibles with
CR suffix
Introduction
This chapter describes how to program your system for the desired interface.
Program the Interface - Plug and Play
Plug and Play bar codes provide instant scanner set up for commonly used interfaces.
Note: After you scan one of the codes, power cycle the host terminal to have the interface in
effect.
Keyboard Wedge
If you want your system programmed for an IBM PC AT and compatibles keyboard
wedge interface with a USA keyboard, scan the bar code below. Keyboard wedge is
the default interface.
Note: The Granit 1980i does not support the keyboard wedge interface.
Note: The following bar code also programs a carriage return (CR) suffix.
Xenon/Granit User Guide 17
Laptop Direct Connect
Laptop Direct Connect
with CR suffix
RS232 Interface
IBM Port 5B Interface
IBM Port 9B
HHBCR-1 Interface
For most laptops, scanning the Laptop Direct Connect bar code allows operation
of the scanner in parallel with the integral keyboard. The following Laptop Direct
Connect bar code also programs a carriage return (CR) suffix and turns on Emulate External Keyboard (page 34).
Note: The Granit 1980i does not support Laptop Direct Connect.
RS232 Serial Port
The RS232 Interface bar code is used when connecting to the serial port of a PC or
terminal. The following RS232 Interface bar code also programs a carriage return
(CR) and a line feed (LF) suffix, baud rate, and data format as indicated below. It
also changes the trigger mode to manual.
Option Setting
Baud Rate 115,200 bps
Data Format 8 data bits, no parity bit, 1 stop bit
RS485
18 Xenon/Granit User Guide
Scan one of the following “Plug and Play” codes to program the scanner for an IBM
POS terminal interface.
Note: This interface is not supported in Granit devices.
After scanning one of these codes, you must power cycle the cash register.
Each bar code above also programs the following suffixes for each symbology:
IBM Port 17 Interface
IBM Port 9B
HHBCR-2 Interface
* Packet Mode Off
Packet Mode On
* Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR-1, and IBM 4683
Port 17 Interfaces
**Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface
RS485 Packet Mode
The following selection allows you to break up large bar code data into smaller
packets on an IBM POS terminal. To break up large bar codes into small packets,
scan the Packet Mode On bar code below. Scan the Packet Mode Off bar code if
you want large bar code data to be sent to the host in a single chunk. Default =
Packet Mode Off.
Symbolog
y
EAN 8 0C Code 39 00 0A 0B
EAN 13 16 Interleaved 2 of 5 00 0D 0B
UPC A 0D Code 128 * 00 0A 0B
UPC E 0A Code 128 ** 00 18 0B
Suffix Symbology Suffix
MaxiCode 00 2F 0B
Xenon/Granit User Guide 19
RS485 Packet Length
Packet Length
USB IBM SurePos
(USB Handheld Scanner)
Interface
USB IBM SurePos
(USB Tabletop Scanner)
Interface
U
S
B
K
e
y
b
o
a
r
d
(
P
C
)
If you are using Packet mode, you can specify the size of the data “packet” that is
sent to the host. Scan the Packet Length bar code, then the packet size (from 20 -
256) from the Programming Chart, beginning on page 353, then Save. Default =
40.
USB IBM SurePos
Scan one of the following “Plug and Play” codes to program the scanner for an IBM
SurePos (USB handheld scanner) or IBM SurePos (USB tabletop scanner) interface.
Note: After scanning one of these codes, you must power cycle the cash register.
Each bar code above also programs the following suffixes for each symbology:
Symbology Suffix Symbology Suffix
EAN 8 0C Code 39 00 0A 0B
EAN 13 16 Interleaved 2 of 5 00 0D 0B
UPC A 0D Code 128 00 18 0B
UPC E 0A Code 39 00 0A 0B
USB PC or Macintosh Keyboard
Scan one of the following codes to program the scanner for USB PC Keyboard or
USB Macintosh Keyboard. Scanning these codes also adds a CR suffix.
20 Xenon/Granit User Guide
USB HID
USB Keyboard (Mac)
USB Japanese Keyboard (PC)
USB HID Bar Code Scanner
USB Serial
CTS/RTS Emulation On
USB Serial
Scan the following code to program the scanner for USB HID bar code scanners.
If you are using a Microsoft® Windows® PC, you will need to download the latest
driver from the Honeywell website (www.honeywellaidc.com) and go to Get
Resources - Downloads - Software. The driver will use the next available COM Port
number. Apple® Macintosh computers recognize the scanner as a USB CDC class
device and automatically use a class driver.
After the driver is downloaded, scan the following code to program the scanner to
emulate a regular RS232-based COM Port.
Note: If you scan the USB Serial bar code either with an older Honeywell serial driver, or no
CTS/RTS Emulation
Xenon/Granit User Guide 21
No extra configuration (e.g., baud rate) is necessary.
driver installed, you may no longer be able to scan bar codes. If this happens, either
uninstall the older driver versions and install the latest driver, or delete the specific
device entry in Device Manager.
ACK/NAK Mode
* CTS/RTS Emulation Off
ACK/NAK Mode On
* ACK/NAK Mode Off
ReM Off
ReM On
Remote MasterMind™ for USB
When using a USB interface, you may wish to configure your scanner to communicate with Remote MasterMind Scanner Management Software (ReM). Scan the
ReM On bar code to communicate with ReM. To disable this capability, scan ReM
Off.
Verifone® Ruby Terminal
22 Xenon/Granit User Guide
Scan the following Plug and Play code to program the scanner for a Verifone Ruby
terminal. This bar code sets the baud rate to 1200 bps and the data format to 8
data bits, mark parity bit, 1 stop bit. It also adds a line feed (LF) suffix and programs the following prefixes for each symbology:
Symbology Prefix
UPC-A A
UPC-E A
EAN-8 FF
EAN-13 F
Gilbarco® Terminal
Verifone Ruby Settings
Gilbarco Settings
Honeywell Bioptic Settings
Datalogic Magellan Settings
Scan the following Plug and Play code to program the scanner for a Gilbarco terminal. This bar code sets the baud rate to 2400 bps and the data format to 7 data bits,
even parity, 2 stop bits. It also adds a carriage return (CR) suffix and programs the
following prefixes for each symbology:
Symbology Prefix
UPC-A A
UPC-E E0
EAN-8 FF
EAN-13 F
Honeywell Bioptic Aux Port
Scan the following Plug and Play code to program the scanner for a Honeywell
bioptic scanner auxiliary port configuration. This bar code sets the baud rate to
38400 bps and the data format to 8 data bits, no parity, 1 stop bit.
Datalogic™ Magellan® Aux Port
Xenon/Granit User Guide 23
Scan the following Plug and Play code to program the scanner for a Datalogic
Magellan auxiliary port configuration. This bar code sets the baud rate to 9600 bps
and the data format to 8 data bits, no parity, 1 stop bit.
NCR Bioptic Aux Port
NCR Bioptic Settings
Wincor Nixdorf Terminal Settings
Scan the following Plug and Play code to program the scanner for an NCR bioptic
scanner auxiliary port configuration. The following prefixes are programmed for
each symbology:
Symbology Prefix Symbology Prefix
UPC-A A Interleaved 2 of 5 b
UPC-E E0 Code 128 f
EAN-8 FF Code 39 a
EAN-13 F
Wincor Nixdorf Terminal
Code 32
Pharmaceutical
(PARAF)
a
Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf
terminal. This bar code sets the baud rate to 9600 bps and the data format to 8
data bits, no parity, 1 stop bit.
Wincor Nixdorf Beetle™ Terminal
Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf
Beetle terminal. The following prefixes are programmed for each symbology:
Symbology Prefix Symbology Prefix
Aztec Code V Interleaved 2 of 5 I
Codabar N MaxiCode T
Code 93 L MicroPDF417 S
Code 128 K PDF417 Q
Data Matrix R QR Code U
EAN-8 B Straight 2 of 5 IATA H
EAN-13 A UPC-A A0
GS1 DataBar E UPC-E C
GS1-128 P All other bar codes M
24 Xenon/Granit User Guide
Wincor Nixdorf RS232 Mode A
Wincor Nixdorf Beetle Settings
Wincor Nixdorf RS232 Mode A
Settings
Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf
RS232 Mode A terminal. This bar code sets the baud rate to 9600 bps and the data
format to 8 data bits, odd parity, 1 stop bit. The following prefixes are programmed
for each symbology:
Note: This setting is not supported in Granit devices.
Symbology Prefix Symbology Prefix
Code 128 K EAN-13 A
Code 93 L GS1-128 K
Codabar N Interleaved 2 of 5 I
UPC-A A0 Plessey O
UPC-E C Straight 2 of 5 IATA H
EAN-8 B GS1 DataBar E
All other bar codes M
Pair with a Honeywell Vehicle Mount Computer
A Xenon/Granit scanner can pair with Honeywell vehicle mount computers, such
as the Thor VM1 or VM2, or with Tecton mobile computers.
Scan the EZPairing bar code that is either supplied with the vehicle mount computer, attached to the vehicle mount computer, or displayed on the screen. The
EZPairing bar code begins with {FNC3} LnkB, followed by 12 digits, like the sample
below.
Keyboard Country Layout
If your interface is USB Keyboard or Keyboard Wedge, your keyboard layout default
is a US keyboard. To change this layout, scan the appropriate Keyboard Country
bar code below. By default, national character replacements are used for the fol-
Xenon/Granit User Guide 25
lowing characters: # $ @ [ \ ] ^ ‘ { | } ~. Refer to the "ISO 2022/ISO 646
* United States
Albania
Azeri (Cyrillic)
Azeri (Latin)
Belarus
Belgium
Bosnia
Brazil
Brazil (MS)
Bulgaria (Cyrillic)
Bulgaria (Latin)
Character Replacements" on page A-346 to view the character replacements for
each country.
Keyboard Countries
26 Xenon/Granit User Guide
Keyboard Countries (Continued)
Canada (French legacy)
Canada (French)
Canada (Multilingual)
Croatia
Czech
Czech (Programmers)
Czech (QWERTY)
Czech (QWERTZ)
Denmark
Dutch (Netherlands)
Estonia
Faroese
Xenon/Granit User Guide 27
Keyboard Countries (Continued)
Finland
France
Gaelic
Germany
Greek
Greek (220 Latin)
Greek (220)
Greek (319 Latin)
Greek (319)
Greek (Latin)
Greek (MS)
Greek (Polytonic)
28 Xenon/Granit User Guide
Keyboard Countries (Continued)
Hebrew
Hungarian (101 key)
Hungary
Iceland
Irish
Italian (142)
Italy
Japan ASCII
Kazakh
Kyrgyz (Cyrillic)
Latin America
Latvia
Xenon/Granit User Guide 29
Keyboard Countries (Continued)
Latvia (QWERTY)
Lithuania
Lithuania (IBM)
Macedonia
Malta
Mongolian (Cyrillic)
Norway
Poland
Polish (214)
Polish (Programmers)
Portugal
Romania
30 Xenon/Granit User Guide
Keyboard Countries (Continued)
Russia
Russian (MS)
Russian (Typewriter)
SCS
Serbia (Cyrillic)
Serbia (Latin)
Slovakia
Slovakia (QWERTY)
Slovakia (QWERTZ)
Slovenia
Spain
Spanish variation
Xenon/Granit User Guide 31
Keyboard Countries (Continued)
Sweden
Switzerland (French)
Switzerland (German)
Tatar
Turkey F
Turkey Q
Ukrainian
United Kingdom
United States (Dvorak)
United States (Dvorak left)
United Stated (Dvorak
United States (International)
32 Xenon/Granit User Guide
Keyboard Countries (Continued)
Uzbek (Cyrillic)
* Off
4 Characters
* Regular
Caps Lock
Keyboard Wedge Modifiers
ALT Mode
If your bar code contains special characters from the extended ASCII chart, for
example, an e with an accent grave (è), you will use ALT Mode. (See Extended ASCII
Characters on page 343.)
Note: Scan the ALT mode bar code after scanning the appropriate Keyboard Country code.
If your keystrokes require the ALT key and 4 characters, scan the 4 Characters bar
code. The data is then output with the special character(s). Default = Off.
Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used
Keyboard Conversion settings, they will override any of the following Keyboard
Style settings. Default = Regular.
Regular is used when you normally have the Caps Lock key off.
Caps Lock is used when you normally have the Caps Lock key on.
Xenon/Granit User Guide 33
Shift Lock is used when you normally have the Shift Lock key on (not common to
Shift Lock
Automatic Caps Lock
Autocaps via NumLock
Emulate External Keyboard
U.S. keyboards).
Automatic Caps Lock is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps Lock on or off . This selection can only be
used with systems that have an LED that notes the Caps Lock status (AT keyboards).
Autocaps via NumLock bar code should be scanned in countries (e.g., Germany,
France) where the Caps Lock key cannot be used to toggle Caps Lock. The NumLock option works similarly to the regular Autocaps, but uses the NumLock key to
retrieve the current state of the Caps Lock.
Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent).
Note: After scanning the Emulate External Keyboard bar code, you must power cycle your
computer.
Keyboard Conversion
Alphabetic keyboard characters can be forced to be all upper case or all lowercase.
So if you have the following bar code: “abc569GK,” you can make the output
“ABC569GK” by scanning Convert All Characters to Upper Case, or to “abc569gk”
by scanning Convert All Characters to Lower Case.
These settings override Keyboard Style selections.
Note: If your interface is a keyboard wedge, first scan the menu code for Automatic Caps
Lock (page 34). Otherwise, your output may not be as expected.
Default = Keyboard Conversion Off.
34 Xenon/Granit User Guide
Control Character Output
* Keyboard Conversion Off
Convert All Characters
to Upper Case
Convert All Characters
to Lower Case
Control Character Output On
* Control Character Output Off
This selection sends a text string instead of a control character. For example, when
the control character for a carriage return is expected, the output would display
[CR] instead of the ASCII code of 0D. Refer to ASCII Conversion Chart (Code Page
1252) on page 342. Only codes 00 through 1F are converted (the first column of
the chart). Default = Off.
Note: Control + X (Control + ASCII) Mode overrides this mode.
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo
Mode.
Xenon/Granit User Guide 35
Control + X (Control + ASCII) Mode On: The scanner sends key combinations for
ASCII control characters for values 00-1F. Windows is the preferred mode. All keyboard country codes are supported. DOS mode is a legacy mode, and it does not
support all keyboard country codes. New users should use the Windows mode.
Refer to ASCII Conversion Chart (Code Page 1252), page 342 for CTRL+ X Values.
Windows Mode Prefix/Suffix Off: The scanner sends key combinations for ASCII
control characters for values 00-1F, but it does not translate prefix or suffix information.
Default = Control + X Mode Off.
Windows Mode Control + X
Mode On
* Control + X Mode Off
DOS Mode Control + X Mode On
Windows Mode Prefix/Suffix
Turbo Mode On
* Turbo Mode Off
Numeric Keypad Mode On
* Numeric Keypad Mode Off
Automatic Direct Connect
Mode On
Turbo Mode: The scanner sends characters to a terminal faster. If the terminal
drops characters, do not use Turbo Mode. Default = Off.
Numeric Keypad Mode: Sends numeric characters as if entered from a numeric
keypad. Default = Off.
Automatic Direct Connect Mode: This selection can be used if you have an IBM AT
style terminal and the system is dropping characters. Default = Off.
36 Xenon/Granit User Guide
RS232 Modifiers
* Automatic Direct Connect
Mode Off
300
600
1200
2400
4800
9600
19200
38400
RS232 Baud Rate
Baud Rate sends the data from the scanner to the terminal at the specified rate.
The host terminal must be set for the same baud rate as the scanner. Default =
115,200.
Xenon/Granit User Guide 37
RS232 Word Length: Data Bits, Stop Bits, and Parity
57,600
* 115,200
7 Data, 1 Stop, Parity Even
7 Data, 1 Stop, Parity None
7 Data, 1 Stop, Parity Odd
7 Data, 2 Stop, Parity Even
7 Data, 2 Stop Parity None
7 Data, 2 Stop, Parity Odd
8 Data, 1 Stop, Parity Even
Data Bits sets the word length at 7 or 8 bits of data per character. If an application
requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full ASCII set, select
8 data bits per character. Default = 8.
Stop Bits sets the stop bits at 1 or 2. Default = 1.
Parity provides a means of checking character bit patterns for validity.
Default = None.
38 Xenon/Granit User Guide
RS232 Receiver Time-Out
* 8 Data, 1 Stop, Parity None
8 Data, 1 Stop, Parity Odd
8 Data, 1 Stop, Parity Mark
RS232 Receiver Time-Out
Flow Control, No Timeout
The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A
manual or serial trigger resets the time-out. When an RS232 receiver is sleeping, a
character may be sent to wake up the receiver and reset the time-out. A transaction
on the CTS line will also wake up the receiver. The receiver takes 300 milliseconds
to completely come up. Change the RS232 receiver time-out by scanning the bar
code below, then scanning digits from the Programming Chart, beginning on page
353, then scanning Save. The range is 0 to 300 seconds. Default = 0 seconds (no
time-out - always on).
RS232 Handshake
RS232 Handshaking allows control of data transmission from the scanner using
software commands from the host device. When RTS/CTS is turned Off, no data
flow control is used.
Flow Control, No Timeout: The scanner asserts RTS when it has data to send, and
will wait indefinitely for CTS to be asserted by the host.
Xenon/Granit User Guide 39
Two-Direction Flow Control: The scanner asserts RTS when it is OK for the host to
transmit. The host asserts CTS when it is OK for the device to transmit.
Flow Control with Timeout: The scanner asserts RTS when it has data to send and
waits for a delay (see RS232 Timeout on page 40) for CTS to be asserted by the
host. If the delay time expires and CTS is not asserted, the device transmit buffer is
cleared and scanning may resume. Default = RTS/CTS Off.
RS232 Timeout
Two-Direction Flow Control
Flow Control with Timeout
* RTS/CTS Off
RS232 Timeout
XON/XOFF On
* XON/XOFF Off
When using Flow Control with Timeout, you must program the length of the delay
you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 1-5100 milliseconds) by scanning digits from the Programming Chart, beginning on page 353,
then scanning Save.
XON/XOFF
Standard ASCII control characters can be used to tell the scanner to start sending
data (XON/XOFF On) or to stop sending data (XON/XOFF Off). When the host
sends the XOFF character (DC3, hex 13) to the scanner, data transmission stops.
To resume transmission, the host sends the XON character (DC1, hex 11). Data
transmission continues where it left off when XOFF was sent. Default = XON/XOFF
Off.
ACK/NAK
40 Xenon/Granit User Guide
After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK
character (hex 15) response from the host. If ACK is received, the communications
cycle is completed and the scanner looks for more bar codes. If NAK is received, the
last set of bar code data is retransmitted and the scanner waits for ACK/NAK again.
ACK/NAK On
* ACK/NAK Off
* Packet Mode Off
Packet Mode On
Turn on the ACK/NAK protocol by scanning the ACK/NAK On bar code below. To
turn off the protocol, scan ACK/NAK Off. Default = ACK/NAK Off.
Scanner to Bioptic Communication
The following settings are used to set up communication between Honeywell scanners and bioptic scanners.
Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to
3000 in order to communicate with a bioptic scanner. See "RS232 Modifiers" on page
37, and RS232 Timeout on page 40 for further information.
Scanner-Bioptic Packet Mode
Packet Mode On must be scanned to set the scanner’s format so it is compatible
with a bioptic scanner. Default = Packet Mode Off.
Scanner-Bioptic ACK/NAK Mode
Bioptic ACK/NAK On must be scanned so the scanner will wait for an ACK or NAK
from a bioptic scanner after each packet is sent. The Scanner-Bioptic ACK/NAK
Timeout (below) controls how long the scanner will wait for a response. Default =
Bioptic ACK/NAK Off.
Xenon/Granit User Guide 41
Scanner-Bioptic ACK/NAK Timeout
* Bioptic ACK/NAK Off
Bioptic ACK/NAK On
ACK/NAK Timeout
This allows you to set the length (in milliseconds) for a timeout for a bioptic scanner’s ACK/NAK response. Scan the bar code below, then set the timeout (from 130,000 milliseconds) by scanning digits from the Programming Chart, beginning
on page 353, then scanning Save. Default = 5100.
42 Xenon/Granit User Guide
CHAPTER
3
CORDLESS SYSTEM OPERATION:
XENON 1902G/1912 AND
GRANIT 1911I/1981I
Note: This chapter does not apply to corded or Xenon 1902g-BF scanners. See Cordless
System Operation: Xenon 1902g-BF beginning on page 81 for Xenon 1902g-BF
scanning systems.
How the Cordless Charge Base/Access Point Works
A cordless charge base or an Access Point provide the link between the cordless
scanner and the host system. The base/Access Point contains an interface assembly and an RF communication module. The RF communication module performs
the data exchange between the cordless scanner and the interface assembly. The
control assembly coordinates the central interface activities including: transmitting/receiving commands and data to/from the host system, performing software
activities (parameter menuing, visual indicator support, power-on diagnostics),
and data translation required for the host system.
The cordless charge base is also a scanner’s battery charger. Refer to Charge
Information, page 49, for additional information.
Link the Scanner to a Charge Base
Turn off power before connecting a base, then power up the computer once the
base is fully connected. When the base is connected and powered up, put the scanner in the base to establish a link. The green LED on the base flashes to indicate
the scanner’s battery is charging.
Xenon/Granit User Guide 43
If the scanner and base have previously been linked, you do not receive any feed-
Xenon Scanner
CCB01-010BT Charge Base
Page Button and Base LEDs
Granit Scanner
CCB02-100BT/CCB05-100BT
Charge Base Page Button and Base
LEDs
Page
Button
back. If this is the first time that the scanner and base are linked, both devices emit
a short chirp when their radios link. At this point, that one scanner is linked to one
base.
To determine if your cordless system is set up correctly, scan one of the sample bar
codes in the back of this manual. If the scanner provides a single good read beep
and the green LED lights, the scanner has successfully linked to the base. If using
a Granit scanner, the scanner also vibrates. If you receive an error tone and the red
LED lights, the scanner has not linked to the base. Refer to page 336 for troubleshooting information.
Link the Scanner to an Access Point
Turn on the computer (laptop/desktop). Plug the interface
cable into the Access Point first and then into the appropriate port on the computer. The Page button lights up when
the connection to the host is made.
Scan the linking bar code on the top of the Access Point to
establish a connection between the Access Point and the
scanner. The scanner emits a short beep and flashes the
green LED to confirm a connection with the Access Point.
The Access Point’s Page button remains blue.
44 Xenon/Granit User Guide
Replace a Linked Scanner
Override Locked Scanner
(Single Scanner)
2
1
1
2
2
If you need to replace a broken or lost scanner that is linked to a base or an Access
Point, scan the Override Locked Scanner bar code below with a new scanner and
place that scanner in the base, or scan the Access Point linking bar code. The
locked link will be overridden; the broken or lost scanner’s link with the base or
Access Point will be removed, and the new scanner will be linked.
Communication Between the Cordless System
and the Host
The cordless scanner provides immediate feedback in the form of a “good read”
indication with a green LED on the scanner and an audible beep. If using a Granit
scanner, the scanner also vibrates. This indicates that the bar code has been
scanned correctly and the base or Access Point has acknowledged receiving the
data. This is possible since the cordless system provides two-way communication
between the scanner and the base or Access Point.
When data is scanned, the data is sent to the host system via the base or Access
Point. The cordless scanner recognizes data acknowledgment (ACK) from the base
or Access Point. If it cannot be determined that the data has been properly sent to
the base or Access Point, the scanner issues an error indication. You must then
check to see if the scanned data was received by the host system.
1. Scanner reads code and gets ACK from base or Access Point
2. Base or Access Point sends data to host
Xenon/Granit User Guide 45
Program the Scanner and Base or Access Point
When using the scanner and charge base or Access Point together as a system,
menu parameters and configuration settings are stored in the charge base or
Access Point. Therefore, when programming any menu configuration settings, the
scanner must be linked to the intended charge base or Access Point.
Note: This only applies when the scanner is linked to a charge base or Access Point. If the
scanner is in a non-base mode, configuration settings are stored in the scanner.
RF (Radio Frequency) Module Operation
The cordless system uses a two-way Bluetooth® radio to transmit and receive data
between the scanner and the base or Access Point. Designed for point-to-point
and multi-point-to-single point applications, the radio operates using a license
free ISM band, which sends relatively small data packets at a fast data rate over a
radio signal with randomly changing frequencies, makes the cordless system
highly responsive to a wide variety of data collection applications and resistant to
noisy RF environments. The CCB01-010BT (Bluetooth Class 2) provides a communication range of 33 feet (10m) between the scanner and base or Access Point,
depending on the environment. The CCB02-100BT/CCB05-100BT (Bluetooth
Class 1) provides a communication range of 330 feet (100m) between the scanner
and base or Access Point, depending on the environment. See Flexible Power
Management, page 61, for information about controlling this range.
System Conditions
The components of the cordless system interact in specific ways as you associate a
scanner to a base or Access Point, as you move a scanner out of range, bring a
scanner back in range, or swap scanners between two cordless systems. The following information explains the cordless system operating conditions.
Link Process
Once a scanner is placed into a cordless charge base, the scanner’s battery charge
status is checked, and software automatically detects the scanner and links it to
the base depending on the selected link mode.
Refer to Link the Scanner to an Access Point, page 44, for information about linking to an Access Point.
Scanner Is Out of Range
The cordless scanner is in communication with its base or Access Point, even when
it is not transmitting bar code data. Whenever the scanner can’t communicate with
the base or Access Point for a few seconds, it is out of range. If the scanner is out of
46 Xenon/Granit User Guide
range and you scan a bar code, the scanner issues an error tone indicating no communication with the base or Access Point. A cordless charge base can also sound
an alarm. Refer to Out-of-Range Alarm,page 58.
Scanner Is Moved Back Into Range
The scanner relinks if the scanner or the base or Access Point have been reset, or
the scanner comes back into range. If the scanner relinks, you will hear a single
chirp when the relinking process (uploading of the parameter table) is complete.
Refer to Out-of-Range Alarm on page 58 for further information.
Out of Range and Back into Range with Batch Mode On
The scanner may store a number of symbols (approximately 500 U.P.C. symbols;
others may vary) when it is out of range and then send them to the base or Access
Point when back in range (see Batch Mode on page 62).
You will not hear a communication error tone in this mode, but you will hear a short
buzz when you pull the trigger if the radio communication is not working. Once the
radio connection is made, the scanner produces a series of beeps while the data is
being transferred to the base or Access Point.
Page Button
When you press the Page button on the base or Access Point, the scanners associated with that base or Access Point will begin beeping (3 short and 1 long beep). If
you pull the trigger on a scanner that is beeping in response, or press the Page button on the base or Access Point a second time, all associated scanners will stop
beeping. See Page on page 54 for further information about Page Button settings.
Note: If you are using a Xenon 1902h model, refer to Quiet Operations - LED and Volume
Settings on page 151 for additional Page Button settings.
Xenon/Granit User Guide 47
Page Button and Presentation Modes
* Temporary Streaming Presentation Mode
On
When in Streaming Presentation Mode, the scanner’s aimer goes out after a short
time, but the scan illumination remains on all the time to continuously search for
bar codes (see Streaming Presentation™ Mode on page 127). When in Temporary
Streaming Presentation Mode, pressing the page button on the base puts the
scanner into Streaming Presentation Mode until the timeout occurs. If a bar code is
scanned before the timeout is reached, the timer starts over.
When the scanner is in the base, press the page button once to put the scanner
into Temporary Streaming Presentation Mode. When the scanner is in the base and
the base has external power (plugged into an outlet), press the page button twice
to put the scanner into Streaming Presentation Mode. Press it twice again to end
Streaming Presentation Mode. When the base does not have external power, pressing the page button twice does not trigger Streaming Presentation Mode.
When the scanner is out of the base, the page button works normally. Default =
Temporary Streaming Presentation Mode On.
To remove Temporary Streaming Presentation Mode, scan the bar code for * Page
Mode On on page 54.
48 Xenon/Granit User Guide
Temporary Streaming Presentation Timeout
*10 Second Timeout
60 Second Timeout
!!
Set a timeout for the length of time the illumination remains on and searching for
bar codes when using Temporary Streaming Presentation Mode. Set the length for
the timeout by scanning one of the bar codes below. Default = 10,000 ms (10 sec-
onds).
About the Battery
Warning: There is a danger of explosion if the batteries are incorrectly
replaced. Replace the batteries with only the same or equivalent
type recommended by the manufacturer. Dispose of used
batteries according to the recycle program for batteries as
directed by the governing agency for the country where the
batteries are to be discarded.
Power is supplied to the cordless scanner by a rechargeable battery that is integrated in the scanner handle. Batteries are shipped only partially charged. The battery should be charged for a minimum of 4 hours before initial use to ensure
optimal performance.
Charge Information
The battery is designed to charge while the scanner is positioned in the cordless
base unit. Refer to Base/Access Point LED Sequences and Meaning,page 51, for
an interpretation of the Charge Status indicators. Refer to Charge Only Mode (page
56) if you need to charge a scanner without linking it to the base.
Place the scanner in the base that is connected to an appropriate power supply.
Use only a Listed Limited Power Source (LPS) or Class 2 type power supply with
output rated 5 to 5.2Vdc, 1A.
Note: If you are powering the base through the interface cable (for example, a USB cable)
and not using an external power supply plugged into the aux port, the current
available for charging is reduced and charge times are increased.
Xenon/Granit User Guide 49
Battery Recommendations
• The battery is a lithium ion cell and can be used without a full charge, and can
also be charged without fully discharging, without impacting the battery life.
There is no need to perform any charge/discharge conditioning on this type of
battery.
• Keep the base connected to power when the host is not in use.
• Replace a defective battery immediately since it could damage the scanner.
• Although your battery can be recharged many times, it will eventually be
depleted. Replace it after the battery is unable to hold an adequate charge.
• If you are not sure if the battery or charger is working properly, send it to
Honeywell International Inc. or an authorized service center for inspection.
Refer to Customer Support on page xvii for additional information.
Caution: Use only Honeywell Li-ion battery packs, model number BAT-
SCN01, rated 3.7 Vdc, 7.4Whr in this device. Use of any nonHoneywell battery may result in damage not covered by the
warranty.
Safety Precautions for Lithium Batteries
• Do not place batteries in fire or heat the batteries.
• Do not store batteries near fire or other high temperature locations.
• Do not store or carry batteries together with metal objects.
• Do not expose batteries to water or allow the batteries to get wet.
• Do not connect (short) the positive and negative terminals, of the batteries, to
each other with any metal object.
• Do not pierce, strike or step on batteries or subject batteries to strong impacts or
shocks.
• Do not disassemble or modify batteries.
Caution: Danger of explosion if batteries are incorrectly replaced.
Dispose of used batteries according to the recycle program for
batteries as directed by the governing agency for the country
where the batteries are to be discarded.
Proper Disposal of the Battery
When the battery has reached the end of its useful life, the battery
should be disposed of by a qualified recycler or hazardous materials
handler. Do not incinerate the battery or dispose of the battery with
general waste materials. You may send the scanner’s battery to us.
(postage paid). The shipper is responsible for complying with all federal, state, and local laws and regulations related to the packing,
50 Xenon/Granit User Guide
labeling, manifesting, and shipping of spent batteries. Contact the Product Service
Department (page xvii) for recycling or disposal information. Since you may find
that your cost of returning the batteries significant, it may be more cost effective to
locate a local recycle/disposal company.
Beeper and LED Sequences and Meaning
The scanner contains LEDs on the rear of the unit that indicate linking status,
decoding state, and battery condition. The base has LEDs on the top of the unit
that indicate its power up, communication, and battery charge condition. The red
LED = error; green LED = success of any type. Scanners and the CCB01-010BT
base have audible indicators as well: 1 razz or error tone = error; 2 beeps = menu
change; 1 beep = all other successes.
The table below lists the indication and cause of the LED indication, beeps, and
vibrations for the scanner.
Scanner LED Sequences and Meaning
LED Indication
Normal
Operation
Red Flash None None Battery low
Green Flash 1 beep None Successful communication or
Red, blinking Razz or error tone None Failed communication
Menu Operation
Green Flash 2 beeps 2 vibrations Successful menu change
Red, blinking Razz or error tone 1 long vibration Unsuccessful menu change
Beeper
Indication
Vibrate
Indication
Base/Access Point LED Sequences and Meaning
The base contains a red LED and the Access Point has a blue LED that indicate the
status of the unit and verifies its communication with the host system. The base
also has a green LED that indicates scanner battery charge condition.
Red or Blue LED - Host Communication
Red or Blue LED Communication Condition
Cause
linking
Off USB suspend
On continuously Power on, system idle
Short blinks in multiple pulses. Occurs while transferring data to/
from the RF module or the Host port.
Receiving data
Xenon/Granit User Guide 51
Green LED - Scanner Battery
* Base Power Communication
Indicator On
Base Power Communication
Indicator Off
Reset Scanner
(base only, does not apply to Access Point)
Green LED Charge Condition
Off Battery not detected or charge
Slow flash, 1 second on, 1 second off Pre-charge and charging
On continuously Charge complete
Fast flash, 300 mSec on, 300 mSec off Charge Error
Base Power Communication Indicator
To display the power indicator on a base or an Access Point, scan the Base Power
Communication Indicator On bar code. To turn off the power indicator, scan the
Off bar code. Default = On.
suspended
Reset Scanner
Scanning this bar code reboots the scanner and causes it to relink with the base or
Access Point.
Scan While in Base Cradle
Note: This feature only applies to the CCB01-010BT base.
If you want to be able to scan bar codes while the scanner is in the base cradle,
scan the Scan in Cradle On bar code below. If you want to only allow scanning
when the scanner is out of the base cradle, scan Scan in Cradle Off. If you want the
scanner to shut down when in the base cradle, scan Shut Down Scanner in Cradle.
Default = Scan in Cradle On (for CCB01-010BT).
52 Xenon/Granit User Guide
Base Charge Modes
Scan in Cradle Off
* Scan in Cradle On
Shut Down Scanner in Cradle
Base Charge Off
External or Interface Cable
Power
When the base has both an external power supply (plugged into the auxiliary power
port) and a host interface cable, it will draw its power from the external power supply. When the base does not have an external power supply, it draws its power from
the interface cable. However, the scanner battery charges more slowly from a host
interface cable than if auxiliary power were available. Using the following selections, you can specify whether the scanner battery is charged from power supplied
via the host interface cable.
When Base Charge Off is selected, the scanner battery does not charge when the
scanner is in the base cradle.
When External or Interface Cable Power is selected, the scanner battery charges
from the base’s external power supply, if there is one. If there is no external power
supply to the base, the scanner battery charges from the interface cable.
When External Power Only is selected, the scanner battery only charges from the
base’s external power supply. If there is no external power supply, the scanner battery does not charge.
Note: If you are using a cordless charge base in Presentation Mode, External Power Only
is the only setting available.
Default = External or Interface Cable Power.
Xenon/Granit User Guide 53
Page
External Power Only
* Page Mode On
Page Mode Off
* Low (1000 Hz)
Medium (3250 Hz)
Page Mode
Note: If you are using a Xenon 1902h model, refer to Quiet Operations - LED and Volume
By default, the paging button on the base or Access Point pages the scanners
associated with that base or Access Point. If you want the paging button on your
base or Access Point to be disabled, scan the Page Mode Off bar code, below.
When Page Mode is off, the base or Access Point will no longer page scanners when
the button is pressed. The red LED on the base or blue LED on the Access Point will
remain lit to indicate that Page Mode is off. (This light will go out when the button
is pressed, then back on when it’s released.) Default = Page Mode On.
Settings on page 151 for additional Page Button settings.
Page Pitch
When you press the Page button on the base or Access Point, the scanners associated with that base or Access Point will begin beeping (see Page Button on page
47). You can set the pitch of the paging beep for each scanner by scanning one of
the following bar codes. Default = Low.
54 Xenon/Granit User Guide
Error Indicators
High (4200 Hz)
* Razz (250 Hz)
Medium (3250 Hz)
High (4200 Hz)
Number of Base Error Beeps/LED Flashes
Beeper Pitch - Base Error
Note: This feature only applies to the CCB01-010BT base.
The CCB01-010BT base can be configured to beep at a particular pitch when an
error occurs, such as transmission problems to a host system. The beeper pitch
codes modify the pitch (frequency) of the error tone the base emits when there is
an error. Default = Low.
Number of Beeps - Base Error
Note: This feature only applies to the CCB01-010BT base.
The number of beeps and LED flashes emitted by the CCB01-010BT base for an
error condition can be programmed from 1 - 9. For example, if you program this
option to have five error beeps, there will be five error beeps and five LED flashes in
response to an error. To change the number of error beeps, scan the bar code below
and then scan a digit (1-9) from the Programming Chart, beginning on page 353,
then Save. Default = 1.
Xenon/Granit User Guide 55
Scanner Report
Scanner Report
Scanner Address
Base Address
Scan the bar code below to generate a report for the connected scanners. The
report indicates the port, work group, scanner name, and address. To assign a
name to your scanner, refer to Menu Command Syntax, page 267.
Scanner Address
Scan the bar code below to determine the address of the scanner you are using.
Base or Access Point Address
Scan the bar code below to determine the address of the base or Access Point you
are using.
Scanner Modes
Your scanner is capable of working in single scanner mode, multiple scanner
mode, or with Bluetooth devices other than the charge base or Access Point.
Charge Only Mode
There may be times when you want to charge your scanner, but not link to the base.
For example, if a scanner is linked to an Access Point or other Bluetooth device and
you need to charge the scanner, but want to retain your existing link.
56 Xenon/Granit User Guide
In order to program the base for Charge Only Mode, you must link a scanner to it.
Charge Only Mode
* Charge and Link Mode
Locked Link Mode
(Single Scanner)
Once the scanner is linked to the base, scan the Charge Only Mode bar code. Any
subsequent scanners placed in that base will charge without linking to it. The
scanner used to program the base remains linked to the base. To unlink this scanner, scan Unlink Scanner on page 58.
Note: When in Charge Only Mode, the scanner periodically wakes up and beeps. See "Power
Up Beeper" on page 5-113 to change this setting.
Charge and Link Mode
If you want to charge a scanner and link to the base, use Charge and Link Mode. If
the base is programmed for Charge Only Mode, you must link a scanner to it first in
order to program it for Charge and Link Mode. Scan the linking bar code on the
base to link the scanner, then scan Charge and Link Mode. Default = Charge and
Link Mode.
Linked Modes
Locked Link Mode and Open Link Mode are the link modes that accommodate different applications. Scan the appropriate bar codes included in the Open Link and
Locked Link Mode explanations that follow to switch from one mode to another.
Default = Open Link Mode.
Locked Link Mode - Single Scanner
If you link a scanner to a base or an Access Point using the Locked Link Mode,
other scanners are blocked from being linked if they are inadvertently placed into
the base, or if the Access Point linking bar code is scanned. If you do place a different scanner into a base, it will charge the scanner, but the scanner will not be
linked.
To use a different scanner, you need to unlink the original scanner by scanning the
Unlink Scanner bar code. (See Scanner Modes,page 56.)
Xenon/Granit User Guide 57
Open Link Mode - Single Scanner
* Open Link Mode
(Single Scanner)
Unlink Scanner
Override Locked Scanner
(Single Scanner)
When newly shipped or defaulted to factory settings, a scanner is not linked to a
base or an Access Point. A link is established when the scanner is placed into a
base, or an Access Point linking bar code is scanned. When in Open Link Mode, a
new link is established when a new scanner is placed in the base, or you scan an
Access Point linking bar code. Each time a scanner is placed into a base or scans
an Access Point linking bar code, the scanner becomes linked to the base or Access
point and the old scanner is unlinked.
Unlink the Scanner
If a base or an Access Point has a scanner linked to it, that scanner must be
unlinked before a new scanner can be linked. Once the previous scanner is
unlinked, it will no longer communicate with the base or Access Point. To unlink the
scanner from a base or an Access Point, scan the Unlink Scanner bar code below.
Override Locked Scanner
If you need to replace a broken or lost scanner that is linked to a base or an Access
Point, scan the Override Locked Scanner bar code below with a new scanner and
place that scanner in the base, or scan the Access Point linking bar code. The
locked link will be overridden; the broken or lost scanner’s link with the base or
Access Point will be removed, and the new scanner will be linked.
Out-of-Range Alarm
If your scanner is out range of the base, an alarm sounds from both your base and
scanner. If your scanner is out range of an Access Point, an alarm sounds from just
the scanner. The alarm stops when the scanner is moved closer to the base or
Access Point, when the base or Access Point connects to another scanner, or when
the alarm duration expires. To activate the alarm options for the scanner or the
58 Xenon/Granit User Guide
base and to set the alarm duration, scan the appropriate bar code below and then
Base Alarm Duration
Scanner Alarm Duration
Base Alarm Type
Scanner Alarm Type
set the time-out duration (from 0-3000 seconds) by scanning digits on the
Programming Chart, beginning on page 353, then Save. Default = 0 sec (no alarm).
Note: The Access Point does not have a base alarm.
Note: If you are out of range when you scan a bar code, you will receive an error tone even if
you do not have the alarm set. You receive the error tone since the data could not be
communicated to the base or Access Point or the host.
Alarm Sound Type
You may change the alarm type for the scanner or a CCB01-010BT base by scanning the appropriate bar code below and then scanning a digit (0-7) bar code from
the Programming Chart, beginning on page 353, then Save. Default = 0.
The sounds are as follows:
Setting Sound
0 3 long beeps, medium pitch
1 3 long beeps, high pitch
2 4 short beeps, medium pitch
3 4 short beeps, high pitch
4 single chirps, medium pitch
5 2 chirps, then 1 chirp, medium pitch
6 single chirps, high pitch
7 2 chirps, then 1 chirp, high pitch
Note: Only the CCB01-010BT base has an alarm.
Xenon/Granit User Guide 59
Scanner Power Time-Out Timer
0 seconds
200 seconds
400 seconds
900 seconds
* 3600 seconds
7200 seconds
When there is no activity within a specified time period, the scanner enters low
power mode. Scan the appropriate scanner power time-out bar code to change the
time-out duration (in seconds).
Note: Scanning zero (0) is the equivalent of setting no time-out.
If there are no trigger pulls during the timer interval, the scanner goes into power
down mode. Whenever the trigger is enabled, the timer is reset. If the scanner is
placed in the charge base cradle and the battery is in the process of being charged,
the scanner will not go into power down mode. Default = 3600 seconds.
Note: When the scanner is in power down mode, pull the trigger to power the unit back up.
There will be a set of power up beeps and a delay of up to a few seconds for the radio
to join. The scanner will then be ready to use.
60 Xenon/Granit User Guide
Flexible Power Management
F
u
l
e
r
R
e
d
u
c
e
d
P
o
w
e
r
Scanner
802.11
LAN
* Full Power
Medium Power
Medium Low Power
Low Power
If you are experiencing network performance issues, and suspect the scanner is
interfering with other devices, you can turn down the power output of the scanner.
This reduces the range between the scanner and a base or an Access Point as
shown in the following illustration:
Scan one of the bar codes below to set the scanner’s power output to Full Power
(100%), Medium Power (35%), Medium Low Power (5%), or Low Power (1%).
Default = Full Power.
Note: Setting a Granit scanner to anything lower than Full Power changes it to Class II
Bluetooth.
l
P
w
o
Xenon/Granit User Guide 61
Batch Mode
* Batch Mode Off
Automatic Batch Mode
Inventory Batch Mode
Persistent Batch Mode
Batch mode is used to store bar code data when a scanner is out of range of its
base or Access Point, or when performing inventory. The data is transmitted to the
base or Access Point once the scanner is back in range or when the records are
manually transmitted.
Note: Batch Mode is only supported by the Honeywell Charge and Communication Base
(CCB) and Honeywell Access Point (AP). Batch mode has limitations when using
multiple scanners to one base or Access Point. If a cordless system is being used in
“multiple link mode,” where up to 7 scanners are to be connected to one base or
Access Point, some accumulated or batched scans could be lost if scanners are
constantly being moved in and out of range.
Automatic Batch Mode stores bar code data when the scanner is out of range of
the base or Access Point. The data is automatically transmitted to the base or
Access Point once the scanner is back in range. When the scanner’s buffer space is
full, any bar codes scanned generate an error tone. In order to scan bar codes
again, the scanner must be moved back into range of the base or Access Point so
data can be transmitted.
Inventory Batch Mode stores bar code data, whether or not you are in range of the
base or Access Point. To transmit the stored data to the base or Access Point, either
place the scanner in the base, or scan Transmit Inventory Records (page 67). When
the scanner’s buffer space is full, any bar codes scanned generate an error tone. In
order to scan bar codes again, the data must be transmitted to the base or Access
Point. Once the data is transmitted, it is cleared in the scanner.
Persistent Batch Mode is the same as Inventory Batch Mode, except that once the
data is transmitted to the base or Access Point, it is retained in the scanner. If you
want to transmit more than once, you can do so using this mode. In order to clear
the scanner’s buffer, you must scan Clear All Codes (see page 66).
Default = Batch Mode Off.
62 Xenon/Granit User Guide
Batch Mode Beep
Batch Mode Beep Off
* Batch Mode Beep On
* Flash Storage
RAM Storage
When scanning in Inventory Batch Mode (page 62), the scanner beeps every time a
bar code is scanned. If using a Granit scanner, it also vibrates. When Batch Mode
Beep is On, you will also hear a click when each bar code is sent to the host. If you
do not want to hear these clicks, scan Batch Mode Beep Off. Default = Batch Mode
Beep On.
Batch Mode Storage
When a scanner is storing data during a Batch Mode process, you can select
whether the data is stored in Flash memory or in RAM.
Flash Storage: The scanner writes any untransmitted data to flash memory prior to
powering down. The data will still be there when the scanner powers back up. However, the scanner will power down, even with untransmitted data, if it reaches a
power down timeout or if the battery power is very low.
RAM Storage: The scanner will not power down while it contains data that has not
been transmitted to the base or Access Point, even if it reaches a power down timeout. However, if the scanner runs out of battery power, it will power down and the
data will be lost.
Default = Flash Storage.
Xenon/Granit User Guide 63
Batch Mode Quantity
* Batch Mode Quantity Off
Batch Mode Quantity On
When in Batch Mode, you may wish to transmit the number of multiple bar codes
scanned, rather than a single bar code multiple times. For example, if you scan
three bar codes called XYZ with Batch Mode Quantity Off, when you transmit your
data it will appear as XYZ three times. Using Batch Mode Quantity On and the
Quantity Codes (page 65), you could output your data as “XYZ, 00003” instead.
Note: If you wish to format your output, for example, place a CR or tab between the bar code
data and the quantity, refer to Data Format beginning on page 167.
Default = Batch Mode Quantity Off.
Enter Quantities
Quantity Codes (page 65) allow you to enter a quantity for the last item scanned,
up to 9999 (default = 1). Quantity digits are shifted from right to left, so if a 5th digit
is scanned, the 1st digit scanned is discarded and the 2nd, 3rd and 4th digits are
moved to the left to accommodate the new digit.
For example, if the Quantity 5 bar code is scanned after the quantity has been set
to 1234, then the 1 is dropped, the quantity will be 2345.
Example: Add a quantity of 5 for the last item scanned.
1. Scan the item's bar code.
2. Scan the quantity 5 bar code.
Example: Add a quantity of 1,500 for the last item scanned.
1. Scan the item's bar code.
2. Scan the quantity 1 bar code.
3. Scan the quantity 5 bar code.
4. Scan the quantity 0 bar code.
5. Scan the quantity 0 bar code.
Example: Change a quantity of 103 to 10.
64 Xenon/Granit User Guide
To correct an incorrect quantity, scan the quantity 0 bar code to replace the incorrect digits, then scan the correct quantity bar codes.
1. Scan the quantity 0 bar code to change the quantity to 1030.
012
345
6
7
8
9
2. Scan the quantity 0 bar code to change the quantity to 0300.
3. Scan the quantity 1 bar code to change the quantity to 3001.
4. Scan the quantity 0 bar code to change the quantity to 0010.
Default = 1.
Quantity Codes
Xenon/Granit User Guide 65
Batch Mode Output Order
* Batch Mode FIFO
Batch Mode LIFO
Total Records
Delete Last Code
Clear All Codes
When batch data is transmitted, select whether you want that data sent as FIFO
(first-in first-out), or LIFO (last-in first-out). Default = Batch Mode FIFO.
Total Records
If you wish to output the total number of bar codes scanned when in Batch Mode,
scan Total Records.
Delete Last Code
If you want to delete the last bar code scanned when in Batch Mode, scan Delete
Last Code.
Clear All Codes
If you want to clear the scanner’s buffer of all data accumulated in Batch Mode,
scan Clear All Codes.
66 Xenon/Granit User Guide
Transmit Records to Host
Transmit Inventory Records
* Batch Mode Transmit Delay Off
(No Delay)
Batch Mode Transmit Delay Short
(250 ms)
Batch Mode Transmit Delay Medium
(500 ms)
Batch Mode Transmit Delay Long
(1000 ms)
If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page
62), you must scan the following bar code to transmit all the stored data to the host
system.
Batch Mode Transmit Delay
Sometimes when accumulated scans are sent to the host system, the transmission
of those scans is too fast for the application to process. To program a transmit
delay between accumulated scans, scan one of the following delays. Default = Off.
Note: In most cases, a short (250 ms (milliseconds)) delay is ideal, however, longer delays
may be programmed. Contact Technical Support (page xvii) for additional
information.
Multiple Scanner Operation
Note: Multiple Scanner Operation Mode allows you to link up to 7 scanners to one base or
Xenon/Granit User Guide 67
Access Point. You cannot join an 8th scanner until you unlink one of the 7 scanners
or take a scanner out of range.
To put the scanner in multiple scanner mode, scan the bar code below. Once you
Multiple Scanner Operation
0001
0002
0003
0004
scan this bar code, the scanner is unlinked from the base or Access Point and must
either be placed into the base, or you must scan the Access Point linking bar code
in order to relink.
Scanner Name
You may assign a name to each scanner you are using for identification purposes.
For example, you may want to have a unique identifier for a scanner that is receiving imaging commands sent from the base or Access Point.
The default name is in the format “ScannerName_Model_SN_XXXXXXXXXX” If you
have more than one scanner linked to a base, and they all have the same name, the
first scanner linked to the base receives commands. When renaming a series of
scanners with identical names, unlink all except one of the scanners from the base.
Perform the rename operation using either the bar codes on page 69, or by sending the serial command :ScannerName:BT_NAMNewName. where ScannerName
is the current name of the scanner, and NewName is the new name for the scanner.
If you wish to change the names of additional scanners, link them one at a time and
repeat the :ScannerName:BT_NAMNewName. command for each scanner.
To rename scanners with sequential, numeric names, scan the bar codes below.
Scan the Reset code after each name change and wait for the scanner to relink to
the base or Access Point before scanning a bar code to rename the next scanner.
68 Xenon/Granit User Guide
You may also scan the Scanner Name bar code below and scan a number for the
0005
0006
0007
Reset
Scanner Name
scanner name. For example, if you wanted to name the linked scanner “312,” you
would scan the bar code below, scan the 3, 1, and 2 bar codes on the Programming
Chart, beginning on page 353, then Save. Scan the Reset bar code and wait for the
scanner to relink to the base.
Application Work Groups
Your cordless system can have up to 7 scanners linked to one base or Access Point.
You can also have up to 7 work groups. If you want to have all of the scanners’ settings programmed alike, you don’t need to use more than 1 work group. If you want
each scanner to have unique settings (e.g., beeper volume, prefix/suffix, data formatter), then you may program each scanner to its own unique work group and
may program each scanner independently. For example, you might want to have
multiple work groups in a retail/warehouse application where you need to have different data appended to bar codes used in the warehouse area versus the retail
area. You could assign all the scanners in the retail area to one work group and
those in the warehouse to another. Consequently, any desired changes to either the
retail or warehouse area would apply to all scanners in that particular work group.
Honeywell’s online configuration tool, EZConfig-Scanning (page 262), makes it
easy for you to program your system for use with multiple scanners and multiple
work groups.
The scanner keeps a copy of the menu settings it is using. Whenever the scanner is
connected or reconnected to a base or an Access Point, the scanner is updated
with the latest settings from the base or Access Point for its work group. The scanner also receives menu setting changes processed by the base or Access Point. If a
scanner is removed from a base or an Access Point and placed into another base or
Xenon/Granit User Guide 69
linked to another Access Point, it will be updated with the new base/Access Point
* Group 0
Group 1
Group 2
Group 3
Group 4
Group 5
Group 6
Factory Default Settings:
All Work Groups
settings for whatever work group to which that the scanner was previously
assigned. For example, if the scanner was in work group 1 linked to the first base, it
will be placed in work group 1 in the second base with the associated settings.
Application Work Group Selection
This programming selection allows you to assign a scanner to a work group by
scanning the bar code below. You may then program the settings (e.g., beeper volume, prefix/suffix, data formatter) that your application requires. Default = Group 0.
Reset the Factory Defaults: All Application Work Groups
The following bar code defaults all of the work groups to the factory default settings.
70 Xenon/Granit User Guide
To see what the factory default settings are, refer to the table of Menu Commands,
Custom Default Settings:
All Work Groups
beginning on page 272. The standard product default settings for each of the commands are indicated by an asterisk (*).
Note: Scanning this bar code also causes both the scanner and the base or Access Point to
perform a reset and become unlinked. The scanner must be placed in the base, or the
Access Point linking bar code must be scanned to re-establish the link. Refer to
Scanner Modes, page 56 for additional information.
If your scanner is in multiple scanner mode, you will hear up to 30 seconds of beeping
while all scanners are relinked to the base or Access Point and the settings are
changed.
Reset the Custom Defaults: All Application Work Groups
If you want the custom default settings restored to all of the work groups, scan the
Custom Product Default Settings bar code below. (If there are no custom defaults,
it will reset the work groups to the factory defaults.) See Set Custom Defaults on
page 14 for further information about custom defaults.
Note: Scanning this bar code also causes both the scanner and the base or Access Point to
perform a reset and become unlinked. The scanner must be placed in its base, or the
Access Point linking bar code must be scanned to re-establish the link. Refer to
Scanner Modes, page 56 for additional information.
If your scanner is in multiple scanner mode, you will hear up to 30 seconds of beeping
while all scanners are relinked to the base or Access Point and the settings are
changed.
Use the Scanner with Bluetooth Devices
The scanner can be used either with the charge base, an Access Point, or with other
Bluetooth devices. Those devices include personal computers, laptops, PDAs, and
Honeywell mobility systems devices.
Bluetooth Secure Simple Pairing (SSP)
Secure Simple Pairing (SSP) allows you to connect simply and securely to other
Bluetooth devices without having to enter a PIN code (as described in Bluetooth
HID Keyboard Connect procedure). SSP is only available when using Bluetooth ver-
Xenon/Granit User Guide 71
sion 2.1 or higher. When SSP is on, no PIN is required for pairing. Turn SSP off if
* Bluetooth SSP On
Bluetooth SSP Off
Bluetooth HID Keyboard
Connect
Bluetooth HID Japanese
Keyboard Connect
Bluetooth PIN Code
you are connecting to a Bluetooth device that is not using a compatible Bluetooth
version. Default = Bluetooth SSP On.
Note: SSP is only supported by the Granit 1981i scanner.
Bluetooth HID Keyboard Connect
Your scanner can be paired with Bluetooth-capable devices, such as personal computers, laptops, and tablets, so that scanned data appears on your device screen as
though it was entered on the keyboard. In order to pair with the Bluetooth device:
1. Scan the appropriate Bluetooth HID Keyboard Connect bar code below.
2. Set your personal computer, laptop or tablet so it searches for other Bluetooth
devices. (Refer to your device’s User Guide for pairing instructions.)
3. Select the scanner name on your device. Some devices will automatically pair
with the scanner. If your device pairs automatically with the scanner, it displays
a successful pairing message and you do not need to continue to the next step.
4. If your device does not automatically pair with the scanner, a PIN is displayed.
This PIN must be scanned within 60 seconds. Quickly scan Bluetooth PIN
Code below, then scan the numeric bar code(s) for the PIN code from the chart
below, then scan Save.
72 Xenon/Granit User Guide
Xenon/Granit User Guide 73
0
1
2
3
4
5
6
7
89Save
Virtual Keyboard
Bluetooth HID Keyboard Disconnect
Non-Base BT Connection
BT Connection - PDA/Mobility Systems Device
Once your scanner has been connected directly to an iPad, smart phone, or laptop,
you can toggle the virtual keyboard on your device with a quick double pull of the
scanner trigger.
Bluetooth HID Keyboard Disconnect
If your scanner has been connected directly to an iPad, smart phone, or laptop
using Bluetooth HID Keyboard Connect (page 72), you must disconnect it in order
to once again communicate with the base or Access Point. Scan the Bluetooth HID
Keyboard Disconnect bar code to unlink the scanner from the currently linked
host. Scan the linking bar code on the base or Access Point to relink the scanner.
Bluetooth Serial Port - PCs/Laptops
Scanning the Non-Base BT Connection bar code below unlinks your scanner and
puts it into a discoverable state. Once the scanner searches for and connects with
a Bluetooth host, the scanner stores the connection to the host device address and
switches virtual COM ports. This allows the scanner to automatically relink to the
host if the connection is lost.
PDAs/Mobility Systems Devices
You may also use the scanner with a PDA or a Honeywell Mobility Systems device.
Scan the bar code below and follow the instructions supplied with your Bluetooth
device to locate the scanner, and connect with it.
74 Xenon/Granit User Guide
Change the Scanner’s Bluetooth PIN Code
Bluetooth PIN
* Auto Reconnect On
Auto Reconnect Off
Some devices require a PIN code as part of the Bluetooth security features. Your
scanner’s default PIN is 1234, which you may need to enter the first time you connect to your PDA or PC. The PIN code must be between 1 and 16 characters. To
change the PIN, scan the bar code below and then scan the appropriate numeric
bar codes from the Programming Chart, beginning on page 353, then Save.
Minimize Bluetooth/ISM Band Network Activity
The settings described below can help you customize the relinking behavior of the
cordless area-imaging system to obtain the best compromise between convenience and low interference.
Note: ISM band refers to the 2.4 to 2.48 GHz frequency band used by wireless networks,
cordless phones, and Bluetooth.
Auto Reconnect Mode
Auto Reconnect controls whether or not the scanner automatically begins the
relink process when a loss of connection is detected. When the Auto Reconnect On
bar code is scanned, the scanner begins the relink process immediately, without
user intervention. Default = Auto Reconnect On.
Note: If you are connecting to a Bluetooth Interface Module, set Auto Reconnect to Off.
The table below shows the results of the Auto Reconnect On and Off settings:
Xenon/Granit User Guide 75
Event Auto Reconnect On Auto Reconnect Off
*Trigger Reconnect On
Trigger Reconnect Off
Scanner out of range Relink occurs automatically. If
maximum number of link attempts
is unsuccessful, then the scanner
must be relinked by either pulling
the trigger, placing the scanner in
the base, or scanning the Access
Point linking bar code. (See
Maximum Link Attempts on page
76.)
Base or Access point reset
(firmware upgrade or power
cycle)
Scanner power down due to
Power Time-Out Timer
setting
Scanner reset due to
firmware upgrade
Scanner reset due to battery
change
Scanner placed in different
base unit
Scanner behaves as if out of range. No attempt to relink made
Trigger must be pulled, Access Point linking bar code must be
scanned, or the scanner must be placed in the base unit to relink.
(Note: scanner relinks on power up, but powers on due to one of the
above actions.)
Relink occurs automatically.
Relink occurs automatically.
Relink to new base occurs automatically.
The scanner is relinked by
pulling the trigger, or scanning
the Access Point linking bar
code.
while base or Access Point is
powered off. Trigger must be
pulled to initiate relinking.
Trigger Reconnect Mode
Note: This setting is only supported by Granit 1981i/1911i.
Trigger Reconnect allows you to control the relink process rather than having it
occur automatically. First scan Auto Reconnect Off (page 75), then scan Trigger
Reconnect On. The scanner begins the relink process when the trigger is pulled.
Default = Trigger Reconnect On.
Maximum Link Attempts
The Maximum Link Attempts setting controls the number of times the scanner
tries to form a connection with a base or an Access Point. During the connection
setup process, the scanner transmits in order to search for and connect to a base
or an Access Point. In order to prevent continuous transmissions that could inter-
76 Xenon/Granit User Guide
fere with other users of the ISM band, the number of attempts to connect is limited
Maximum Link Attempts
Relink Time-Out
by this setting. After the maximum number of attempts is reached, the scanner will
not attempt to reconnect to a base or an Access Point. Pressing the trigger, scanning an Access Point linking bar code, or placing the scanner in the cradle resets
the attempt count and the scanner will again try to link.
Scan the Maximum Link Attempts bar code, then scan the number of attempts for
the setting (from 0-100) from theProgramming Chart, beginning on page 353,
then Save. Default = 0.
Note: When Auto Reconnect Mode is On, setting Maximum Link Attempts to zero will cause
the scanner to try to link until the Power Time-Out Timer setting expires. When Auto
Reconnect Mode is Off, setting Maximum Link Attempts to zero will cause the
scanner to only attempt linking one time after a trigger pull.
Relink Time-Out
Relink Time-Out controls the idle time between relink attempts. An attempt to link
a scanner to a base or an Access Point typically lasts up to 5 seconds. This is the
time when the scanner is actually attempting a contact . Relink Time-Out controls
the amount of time, in seconds, that elapses between the end of one connection
attempt and the start of the next.
Note: The length of time for an attempt depends on the number of scanners connected to
a base unit or Access Point. An extra 7 seconds may be required when a connection is
successful.
Scan the Relink Time-Out bar code, then scan the number of seconds for the setting (from 1-100) from the Programming Chart, beginning on page 353, then
Save. Default = 3 seconds.
Bluetooth/ISM Network Activity Examples
Default values
When the scanner goes out of range, the scanner repeatedly attempts to connect
to the base unit or Access Point. Each attempt consists of approximately 5 seconds
of active time followed by 3 seconds of idle time. After one hour, the scanner powers off and batch mode data is lost.
Example: Maximum Link Attempts set to 15
Other values at default setting
Xenon/Granit User Guide 77
When the scanner goes out of range, 15 attempts are made to link to the base unit
or Access Point. Each attempt consists of approximately 5 seconds of active time
followed by 3 seconds of idle time. After 15 cycles (8*15 =120), or about 2 minutes,
the scanner stops trying to connect to the base or Access Point, but retains any bar
codes that may have been saved in batch mode. After one hour, the scanner powers
off and batch mode data is lost.
Example: Auto Reconnect Mode set to 0
Maximum Link Attempts set to 15
Other values at default setting
When the scanner goes out of range, no action is taken to relink. When the trigger
is pulled, 15 attempts are made to link to the base or Access Point. Each attempt
consists of approximately 5 seconds of active time followed by 3 seconds of idle
time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to
connect to the base or Access Point, but retains any bar codes that may have been
saved in batch mode. After one hour, the scanner powers off and batch mode data
is lost. Refer to Auto Reconnect Mode, page 75, to review other events that can
start the relink process.
Example: Auto Reconnect Mode set to 1
Maximum Link Attempts set to 0
Relink Time-Out set to 10
Scanner Power Time-Out Timer set to 1800
Note: See Scanner Power Time-Out Timer on page 60.
The scanner attempts to connect to the base or Access Point every 15 seconds,
measured from one attempt start to the next attempt start. After one half hour, the
scanner powers off.
Host Acknowledgment
Some applications require that the host terminal (or server) validate incoming bar
code data (database look-up) and provide acknowledgment to the scanner
whether or not to proceed. In Host ACK Mode, the scanner waits for this acknowledgment after each scan. Visual and audible acknowledgments provide valuable
feedback to the scan operator. The Host ACK functionality is controlled via a number of pre-defined escape commands that are sent to the scanner to make it
behave in different ways.
Note: System performance degrades when using Host ACK at rates lower than 9600 baud.
The following criteria must be met for the Host ACK to work correctly:
• The co rdles s syst em must be conf igured for Hos t Por t R S2 32 (te rm inal I D = 000)
or USB COM Emulation (terminal ID = 130).
• RTS/CTS is defaulted off. You must enable it if the host system requires it.
• Host ACK must be set to On (page 80).
78 Xenon/Granit User Guide
• A comma must be used as a terminator.
• The host terminal software must be capable of interpreting the bar code data,
make decisions based on the data content, and send out appropriate escape
commands to the scanner.
Escape commands are addressed to the scanner via “Application Work Groups.”
Once a command is sent, all scanners in a group respond to that command.
Because of this, it is recommended that each scanner is assigned to its own
group in Host ACK mode.
The commands to which the scanner responds are listed on page 80. The [ESC] is a
1B in hex. A typical command string is y [ESC] x, where “y” is the application work
group number, “[ESC] x” is the escape command, and the comma is the terminator,
which is required. (When “y” is not specified, the command is sent to the default
Application Work Group 0.)
Example: Commands may be strung together to create custom response sequences. An
example of a command string is listed below.
[ESC]4,[ESC]5,[ESC]6,
The above example will make a scanner that is in application work group zero beep
low, then medium, then high.
Example: A good read beep is required for any item on file, but a razz or error tone is required
if the item is not on file. In this case,
[ESC]7, is sent from the host to the scanner for an on-file product
[ESC]8,[ESC]8, is sent from the host to the scanner for a not-on-file product
When a bar code is scanned, the scanner enters a timeout period until either the
host ACK sequence is received, or the timeout expires (in 10 seconds, by default).
Once Host ACK is enabled, the system works as follows when a bar code is
scanned:
• The scanner reads the code and sends data to the base or Access Point to
transmit to the host system. No audible or visual indication is emitted until the
scanner receives an escape command. The scanner read illumination goes out
when there’s a successful read.
• Scanner operation is suspended until 1) a valid escape string is received from
the host system or 2) the scanner times out.
• Once condition 1 or 2 above has been met, the scanner is ready to scan again,
and the process repeats.
A time-out occurs if the scanner does not receive a valid escape command within
10 seconds. A time-out is indicated by an error tone. If a time-out occurs, the operator should check the host system to understand why a response to the scanner
was not received.
Xenon/Granit User Guide 79
Host ACK On/Off
Host ACK On
* Host ACK Off
Host ACK Timeout
Host ACK Timeout
You can set a timeout for the length of time the scanner waits for a valid escape
command when using Host Acknowledgment Mode. Set the length (in seconds) for
a timeout by scanning the following bar code, then setting the timeout (from 1-90
seconds) by scanning digits from the Programming Chart, beginning on page 353,
then Save. Default = 10.
Host ACK Responses
Command Action
[ESC] a, Double beeps to indicate a successful menu change was made.
[ESC] b, Razz or error tone to indicate a menu change was unsuccessful.
[ESC] 1, The green LED illuminates for 135 milliseconds followed by a pause.
[ESC] 2, The green LED illuminates for 2 seconds followed by a pause.
[ESC] 3, The green LED illuminates for 5 seconds followed by a pause.
[ESC] 4, Emits a beep at a low pitch.
[ESC] 5, Emits a beep at a medium pitch.
[ESC] 6, Emits a beep at a high pitch.
[ESC] 7, Beeps to indicate a successful decode and communication to host.
[ESC] 8,[ESC] 8, Razz or error tone to indicate a decode/communication to host was
unsuccessful.
80 Xenon/Granit User Guide
Loading...