IP 66IP 66
IP 67
IEC 60947...
IEC 60947...
A Optical axis
ODSL 96B M/C6-2000 Ex d
ODSL 96B M/L-2000 Ex d
ODSL 96B Ex d Optical laser distance sensors
Dimensioned drawing
en 06-2017/02 50108369-03
150 … 2000mm
Reflection-independent distance
information
Highly insensitive to extraneous light
Analog current output
Configurable measurement range and
measure mode
Configuration via PC/OLED display and key
pad (the sensor must be removed from the
Ex housing for this purpose)
Teachable switching output and analog
output
EC type examination certificate
DEKRA 13 ATEX 0209
II 2G Ex d op is IIB+H
2
T4 Gb
II 2D Ex tb IIIC T135°C Db
Cable 15m, 5-wire
Accessories:
(available separately)
Configuration software
Electrical connection
We reserve the right to make changes • PAL_ODSL96BEx_en_50108369_03.fm
Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 7021 5730
info@leuze.com • www.leuze.com
ODSL 96B … Ex d - 06
ODSL 96B Ex d
Specifications
Optical data
Measurement range
Resolution
Light source laser
Laser class 2 in accordance with IEC 60825-1:2007
Wavelength 650nm
Max. output power 1.2mW
Pulse duration 22ms
Light spot divergent, 2x6 mm² at 2 m
2)
Error limits (relative to measurement distance)
Absolute measurement accuracy
Repeatability
B/W detection thresh. (6 … 90% rem.) ≤ 1%
Temperature compensation yes
Timing
Measurement time 1 … 51)ms
Response time
Delay before start-up ≤ 300 ms
Electrical data
Operating voltage UB 18 … 30V DC (incl. residual ripple)
Residual ripple ≤ 15 % of U
Open-circuit current ≤ 150 mA
Outputs ODSL 96B M/C6-2000 Ex d
Switching output push-pull switching output 5),
Signal voltage high/low ≥ (UB-2 V)/≤ 2V
Analog output voltage 1 … 10V, R
Sensor operating mode ODSL 96B M/L-2000 Ex d
IO-Link COM2 (38.4kBaud), Frame 2.2, Vers. 1.0,
SIO
Indicators Teach-in on GND Teach-in on +U
Green LED continuous light ready
Yellow LED continuous light object inside teach-in measurement distance
Mechanical data Metal housing
Housing diecast zinc
Optics cover glass
Weight 380g
Connection type Cable 15m, 5-wire
Environmental data
Ambient temp. (operation/storage) -20°C … +50°C/-30°C … +70°C
Protective circuit
VDE safety class
Protection class IP 66, IP 67
Standards applied IEC 60947-5-2
Explosion protection
Certification (CENELEC) II 2G Ex d op is IIB+H2 T4 Gb
1) Luminosity coefficient 6 % … 90 %, complete measurement range, at 20°C, medium range of UB, measurement object
≥ 50x 50 mm²
2) Minimum and maximum value depend on measurement distance
3) Same object, identical environmental conditions, measurement object ≥ 50x50 mm²
4) Typ. ± 0.02 %/K
5) The push-pull switching outputs must not be connected in parallel
6) 1=transient protection, 2=polarity reversal protection, 3=short circuit protection for all outputs
7) Rating voltage 250 VAC, with cover closed
1)
3)
1)
flashing fault teach event
off no voltage
flashing teach event
off object outside teach-in measurement distance
6)
7)
1)
150 … 2000mm
1…3mm
±1,5%
±0,5%
4)
≤ 15 ms
B
PNP light switching, NPN dark switching
≥ 2kΩ
current 4 … 20mA, RL≤ 500Ω
min. cycle time 2.2ms
not supported
1, 2, 3
II, all-insulated
II 2D Ex tb IIIC T135°C Db
L
B
Tables
Diagrams
Remarks
Operate in accordance with
intended use!
This product is not a safety sensor
and is not intended as personnel
protection.
The product may only be put into
operation by competent persons.
Only use the product in accor-
dance with the intended use.
Order guide
Designation Part no.
Cable connection, 15m
Current output ODSL 96B M/C6-2000 Ex d 50106735
Measurement time
depends on the reflectivity
of the measurement
object and on the
measurement mode.
IO-Link interface ODSL 96B M/L-2000 Ex d 50136154
ODSL 96B … Ex d - 06 2017/02
A Laser exit opening
B Laser warning sign
A
B
AVOID EXPOSURE – LASER RADIATION
IS EMITTED FROM THIS APERTURE
EXPOSITION DANGEREUSE – UN RAYONNEMENT
LASER EST ÉMIS PAR CETTE OUVERTURE
LASERSTRAHLUNG
NICHT IN DEN STRAHL BLICKEN
LASER KLASSE 2
DIN EN 60825-1:2008-05
Max. Leistung (peak):
Impulsdauer:
Wellenlänge:
RADIAZIONE LASER
NON FISSARE IL FASCIO
APARRECCHIO LASER DI CLASSE 2
EN 60825-1:2007
Potenza max. (peak):
Durata dell'impulso:
Lunghezza d'onda:
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
EN 60825-1:2007
Maximum Output (peak):
Pulse duration:
Wavelength:
RAYONNEMENT LASER
NE PAS REGARDER DANS LE FAISCEAU
APPAREIL À LASER DE CLASSE 2
EN 60825-1:2007
Puissance max. (crête):
Durée d`impulsion:
Longueur d`onde:
RADIACIÓN LÁSER
NO MIRAR FIJAMENTE AL HAZ
PRODUCTO LÁSER DE CLASE 2
EN 60825-1:2007
Potencia máx. (peak):
Duración del impulso:
Longitud de onda:
RADIAÇÃO LASER
NÃO OLHAR FIXAMENTE O FEIXE
EQUIPAMENTO LASER CLASSE 2
EN 60825-1:2007
Potência máx. (peak):
Período de pulso:
Comprimento de onda:
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
IEC 60825-1:2007
Complies with 21 CFR 1040.10
Maximum Output (peak):
Pulse duration:
Wavelength:
䉏⏘戟⺓
▎䦃展⏘㧮
伊䉏⏘ℶ❐
GB7247.1-2012
㦏⮶戢⒉᧤⽿⋋᧥
厘⑁㖐兼㢅梃
㽱栎
1,2 mW
22 ms
650 nm
1,2 mW
22 ms
650 nm
1.2 mW
22 ms
650 nm
1,2 mW
22
m
s
650 nm
1,2 mW
22 ms
650 nm
1,2 mW
22 ms
650 nm
1.2 mW
22 ms
650 nm
1.2 mW
22 ms
650 nm
50106507-05
ODSL 96B Ex d Optical laser distance sensors
Laser safety notices
ATTENTION, LASER RADIATION – LASER CLASS 2
Never look directly into the beam!
The device satisfies the requirements of IEC 60825-1:2007 (EN 60825-1:2007) safety regulations for a product in laser class 2 as well
as the U.S. 21 CFR 1040.10 regulations with deviations corresponding to "Laser Notice No. 50" from June 24th, 2007.
Never look directly into the laser beam or in the direction of reflecting laser beams!
If you look into the beam path over a longer time period, there is a risk of injury to the retina.
Do not point the laser beam of the device at persons!
Intercept the laser beam with an opaque, non-reflective object if the laser beam is accidentally directed towards a person.
When mounting and aligning the device, avoid reflections of the laser beam off reflective surfaces!
CAUTION! Use of controls or adjustments or performance of procedures other than specified herein may result in hazardous light
exposure.
Adhere to the applicable legal and local regulations regarding protection from laser beams.
The device must not be tampered with and must not be changed in any way.
There are no user-serviceable parts inside the device.
Repairs must only be performed by Leuze electronic GmbH + Co. KG.
NOTICE
Affix laser information and warning signs!
Laser information and warning signs are affixed to the device(see
(stick-on labels) are supplied in several languages (see
).
Affix the laser information sheet with the language appropriate for the place of use to the device.
When using the device in the US, use the stick-on label with the "Complies with 21 CFR 1040.10" notice.
Affix the laser information and warning signs near the device if no signs are attached to the device (e.g. because the device is too
small) or if the attached laser information and warning signs are concealed due to the installation position.
Affix the laser information and warning signs so that they are legible without exposing the reader to the laser radiation of the device
or other optical radiation.
). In addition, self-adhesive laser information and warning signs
Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 7021 5730 ODSL 96B … Ex d - 06
info@leuze.com • www.leuze.com
A Screw M6
B Lock washer
C Washer
D Cable lug
ODSL 96B Ex d
Notices for the safe use of sensors in potentially explosive areas
Intended application range
The distance sensors of the ODSL 96B Ex d series, without making contact, detect objects which are located in or move through the
light beam and measure the distance to these objects.
Validity
The sensors have an encapsulated, pressure-proof housing and can be used in the following areas with these classifications:
Device group Device category Equipment protection
level
II 2G Gb Zone 1
II 2D Db Zone 21
Attention!
Check whether the equipment classification corresponds to the requirements of the application.
The devices are not suited for the protection of persons and may not be used for emergency shutdown purposes.
A safe operation is only possible if the equipment is used properly and for its intended purpose.
Electrical equipment may endanger humans and (where applicable) animal health, and may threaten the safety of
goods if used incorrectly or under unfavorable conditions in potentially explosive areas.
The applicable national regulations (e.g. EN 60079-14) for the configuration and installation of explosion-proof
systems must be observed.
Installation, Commissioning
Attention!
Electrical equipment may endanger humans and (where applicable) animal health, and may threaten the safety of goods if
used incorrectly and under unfavorable conditions in potentially explosive areas.
A safe operation in potentially explosive areas is only possible if the equipment is used properly and for its intended purpose.
The distance sensors of type ODSL 96B Ex d must only be installed and maintained by trained electricians.
When installing the sensors in Ex zones 1 and 21, the
connection cable must be connected in a connection space
with increased safety Ex e, or outside the Ex area.
The housing must be connected to the protective conductor
system at the marked external connection terminal. For this
purpose, always use a cable lug and make the connection
as shown in the diagram. Fastening screw (A) is to be
secured with a lock washer (B) to protect against loosening.
Zone
The respective applicable national regulations for the installation of electrical equipment in potentially explosive areas
must be observed.
ODSL 96B … Ex d - 06 2017/02
ODSL 96B Ex d Optical laser distance sensors
Maintenance
No changes may be made to the devices of type ODSL 96B Ex d for potentially explosive areas.
Repairs to the sensors may only be performed by persons trained for such work or by the manufacturer. Defective devices must be
replaced immediately.
The housing must not be opened while the power is on! After switching off power, wait at least 10min. before opening the housing.
Cyclical maintenance of the sensors is not necessary.
Depending on the environmental conditions, it may occasionally be necessary to clean the light-emission surfaces of the sensors. This
cleaning must only be performed by persons trained for performing this task. A soft, damp cloth should be used for this purpose. Cleaning agents that contain solvents must not be used.
Chemical resistance
The sensors of type ODSL 96B Ex d demonstrate good resistance against many diluted acids and bases.
Exposure to organic solvents is possible only under certain circumstances and only for short periods of time.
Resistance to chemicals should be examined on a case by case basis.
Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 7021 5730 ODSL 96B … Ex d - 06
info@leuze.com • www.leuze.com
ODSL 96B M/C6-2000 Ex d
Analog output
A Area not defined
B Linearity not defined
C Measurement range
D Object present
E No object detected
F Measurement distance
Teach-in of switching outputs and characteristic output curve (Time Control, factory setting)
ODSL 96B Ex d
- Position the measured object at the desired distance.
- Activate the "teach in" input (pin 2) (with factory settings by applying +U
The duration of the activation of the teach input determines the teach step according to the table shown below. The teach event is indicated by the flashing of the LEDs and on the display.
Teach function Duration of teach signal Green LED Yellow LE D
Switching output Q1
Teach point
Distance value for start of measurement range =
1V / 4mA at analogue output (pin 5)
Distance value for end of measurement range =
10V / 20mA at analogue output (pin 5)
At the end of the given teach event:
- Reconnect the teach input to GND.
A successful teach event is signaled by the end of the flashing of the LEDs.
2 … 4s Flash synchronously
4 … 6s Continuous light Flash
6 … 8s Flash Continuous light
).
B
Notice
If the measurement range start is taught to a distance greater than the measurement range end, a declining characteristic
output curve is automatically set.
Error messages
Continuously flashing LEDs signal an unsuccessful teach event. The sensor remains ready for operation and continues to function with
the old values.
Remedy:
- Repeat teach event or
- Activate teach input for more than 8s or
- Disconnect sensor from voltage to restore the old values.
ODSL 96B M/L-2000 Ex d
IO-Link process data
Output data device
Data bit
A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
MSB
16 bit measurement value: distance
1 bit output resolution: 1mm
Signal too weak: 65535
Laser error: 65533
ODSL 96B … Ex d - 06 2017/02
16 bit measurement value
LSB
Loading...