Leuze ODSIL 96B Data Sheet

18 - 30 V

DC

IEC 60947...

IEC 60947...

IPIP 69K69K
IPIP 6767

A Green indicator diode
B Indicator diode yellow
C Transmitter (infrared light) for distance measurement
D Receiver
E Optical axis
F Device plug M12 x1
G Countersinking for SK nut M5, 4.2mm deep
H OLED display
I Reference edge for the measurement (cover glass)
K Key pad
L Green and yellow indicator diodes
M Transmitter (red light) as alignment aid
N Button for switching red alignment laser on/off

ODSIL 96B M/C6… ODSIL 96B M/V6…

ODSIL 96B Optical laser distance sensors

Dimensioned drawing

en 03-2013/01 50114025

0.3 … 10m

 Measurement range up to 10000mm at

90% diffuse reflection

 Reflection-independent distance informa-

tion up to 6000mm

 Infrared laser diode with laser class 1
 Switchable alignment aid with red light laser

diode with laser class 1

 Highly insensitive to extraneous light
 Analog current or voltage output
 PC/OLED display and membrane keyboard

for configuration

 Measurement value is indicated in mm on

OLED display

 Measurement range and mode adjustable
 Input (pin 2) for deactivation of laser, trig-

gering, offset correction or teach-in

Electrical connection

Accessories:

(available separately)

 Mounting systems
 Cable with M12 connector

(K-D …)

We reserve the right to make changes • DS_ODSIL96BMTOF_en_50114025.fm

 Configuration software

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. [phone]

ODSIL 96B M/… - 03

ODSIL 96B

Specifications

Optical data

Measurement range 300 … 10000mm (90% diffuse reflection),

Resolution 3mm
Light source laser
Wavelength measurement laser: 785nm (infrared light),

Light spot approx. 7x7 mm² at 10 m
Max. output power measurement laser: 268mW,

Pulse duration measurement laser: 6.5 ns,

Error limits (relative to measurement range end value 6000mm)

Absolute measurement accuracy
Repeatability
B/W detection thresh. (6 … 90% rem.) ± 10mm
Temperature drift ± 1.5mm/K

2)

1)

300 … 6000mm (6 … 90% diffuse reflection)

alignment laser: 658nm (visible red light)

alignment laser: 190mW

alignment laser: 6.5ns

±0.5%
±5mm

Timing

Measurement time "Fast" operating mode: 2.8ms

Delay before start-up  300 ms

"Standard" operating mode: 20ms
"Precision" operating mode: 100ms (factory setting)

Electrical data

Operating voltage U
Residual ripple  15 % of UB
Open-circuit current  150mA
Switching output push-pull switching output

Signal voltage high/low  (UB-2 V)/ 2V
Analog output

B

…C6/V6 18 … 30VDC (incl. residual ripple)

3)

PNP light switching, NPN dark switching

…V6 voltage 1…10V / 0…10V / 1…5V / 0…5V, R

…C6

current 4 … 20mA, RL 500 

,

 2k

L

Indicators Teach-in on GND

Green LED continuous light ready

Yellow LED continuous light object within range / switching output

off no voltage

off object out of range / switching output

Mechanical data Metal housing

Housing diecast zinc
Optics cover glass
Weight 380g
Connection type M 12 connector

Environmental data

Ambient temp. (operation/storage) -20 °C … +50°C / -30°C … +70°C
Protective circuit
VDE safety class
Protection class IP 67, IP 69K
Laser class 1 (acc. to EN 60825-1)
Standards applied IEC 60947-5-2

1) For 300 … 6000mm measurement range, luminosity coefficient 6% … 90 %, "Precision" operating mode, floating
average calculation taking 30 measurement values into account, at 20°C after 20 min. warmup time, medium range

, measurement object  50x 50mm²

of U

B

2) Same object, identical environmental conditions, "Precision" operating mode, floating average calculation taking
30 measurement values into account, after 20 min. warmup time, measurement object

3) The push-pull switching outputs must not be connected in parallel

4) 1=transient protection, 2=polarity reversal protection, 3=short circuit protection for all outputs

5) Rating voltage 250 VAC, with cover closed

6) IP 69K test in accordance with DIN 40050 part 9 simulated, high pressure cleaning conditions without the use
of additives. Acids and bases are not part of the test

4)

5)

1, 2, 3
II, all-insulated

6)

 50 x50 mm²

Order guide

Designation Part no.

Analogue current output

Current output, teach input, 1 push/pull output ODSIL 96B M/C6-S12 50109302

Analogue voltage output

Voltage output, teach input, 1 push/pull output ODSIL 96B M/V6-S12 50109303

Tables

Diagrams

Remarks

 Approved purpose:

This product may only be
used by qualified person­nel and must only be used
for the approved purpose.
This sensor is not a safety
sensor and is not to be
used for the protection of
persons.

 The red light laser diode is

used exclusively as an
alignment aid. The beam
radiates at a distance of
17mm parallel to the infra­red measurement beam
(see dimensioned draw­ing).

ODSIL 96B M/… - 03 2013/01

FactorySettings
Execute

ODSIL 96B Optical laser distance sensors

Analog output: characteristic curve for factory setting

Factory setting

A Area not defined
B Linearity not defined
C Measurement range
D Object present
E No object detected
F Measurement distance

200 300 6000 6300

Measurement mode and measurement filter

The user can individually adapt the measurement system of the ODSIL 96B to various applications. By configuring the measure­ment mode and measurement filter, either a higher measurement accuracy or, alternatively, faster measurements can be
achieved. Configuration can be performed either directly on the sensor or with the ODS 96B configuration software.

Optimization of measurement mode

In the Application menu, you can set 3 different measurement filters.

Menu setting Effect

Application -> Measure Mode -> Precision high accuracy, measurement time of individual measurement: 100ms
Application -> Measure Mode -> Standard exact and fast, measurement time of individual measurement: 20ms
Application -> Measure Mode -> Speed fast measurement, measurement time of individual measurement: 2.8ms

Optimization of measurement filter

To achieve more precise measurement values, a measurement filter can be adjusted in addition to the measurement mode. In
most cases, the use of a floating average results in a reduction in the variance of the measurement values.
To use this, select the menu setting Application -> Measure Filter -> Averaging.

The number of measurement values to be taken into account can be set to a value between 1…99 via menu setting
Application -> Measure Filter -> Averaging -> Measurem. Count.

Notice!

The measurement value display on the OLED display can be used to assess the efficiency of the selected measurement
mode and measurement filter in the application. The update rate of the OLED display is always 2Hz. The ODS 96B con­figuration software provides identical functionality.

Factory setting of measurement mode:

On delivery, the sensor is preset so that measurement values with the maximum possible accuracy are achieved:

 Measurement mode Precision.

Reset to factory settings

Press the  button while switching on the device to reset the configuration of the ODSIL 96B to the state upon delivery from the
factory.

Press the
viously are permanently lost.

Press  and the ODSIL 96B returns to measurement operation without resetting the parame­ters.

You can also use the menu or the configuration software to reset to factory settings. For this purpose, select menu item
Settings -> FactorySettings -> Execute.

The ODS 96B configuration software can also be used to reset the ODSIL 96B to factory settings.

button again to reset all parameters to the factory settings. All settings made pre-



Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. [phone] ODSIL 96B M/… - 03

Inactive Low 0V

T

t

Active High +24V

ODSIL 96B

Teach-in of switching outputs, analog characteristic output curve and Preset

Notice!

If you have changed the factory setting for teaching under Input Mode, activate on the OLED display the menu item
Input -> Input Mode -> Teach.

To teach, proceed as follows:

1.Position measurement object at the desired measurement distance.

2.The respective teach function is activated on the teach input for the duration of a level change T (see graphical representation).

The level conditions describe the levels with menu setting Input -> Input Mode -> Input polarity -> Active High +24V (factory
setting).

Teach function Duration T

Switching output Q1 20 … 80ms
Distance value for start of measurement range =

1V or 4mA at analog output
Distance value for end of measurement range =

10V or 20mA at analog output

Notice!

If the inactive level is continuously applied on the teach input, the teach input is locked.

For menu setting Input -> Input Mode -> Input polarity -> Active Low +0V, inverted input signals are used during
teaching.

220 … 280ms

320 … 380ms

Preset Teach-In

On the OLED display, activate for this purpose menu item Input -> Input Mode -> Preset.

The preset teach occurs in a manner analogous to that for the teach-in for switching output Q1.

ODSIL 96B M/… - 03 2013/01