Lenovo LXH-GJ769F4 User Manual

Table of Contents
Certifications…………………………………………………………….. 2
Warning and Caution…………………………………………………… 3
Installation of Monitor……………………………………………………
Using OSD…..…………………………………………………………...
Green and P&P………………………………………………………….
Trouble shooting…………………………………………………………

4

8

10

10

Appendix A—Specifications……………………………………………. 13
Appendix B—Factory mode…………………………………………… 14
Appendix C—Pin assignment…………………………………………. 14
Appendix D—Dimension……………………………………………….

14

Notice:

Please read the following words before assembling and using this monitor.
Any reference to an Lenovo product, program or service is not int ended to state or
imply that only Lenovo’s product, program, or service may be used. Any functionally
equivalent product, program, or service that does not infringe any of Lenovo’s
intellectual property rights or other legally protectable rights may be used instead of
the Lenovo product, program, or service. Evaluation and verification of operation in
conjunction with other products, programs, or services, except those expressly
designated by Lenovo, are the user’s responsibility.
Lenovo may have patents or pending patent applications covering subject matter in
this document. The furnishing of this document does not give you any license to
these patents.
Information in this document is subject to change without notice.
Without the permission of Lenovo (Beijing) Limited, no part of this manual may be
reproduced or distributed in any form or by any means.

lenovo® is a Lenovo (Beijing) Limited registered trademark.

41CD785-608-4B

1

FCC Class B Radio Frequency Interference Statement

WARNING: (FOR FCC CERTIFIED MODELS)

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4. Consult the dealer or an experienced radio/TV technician for help.

41CD785-608-4B

2

Notice:

1. The changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

2. The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modification to this equipment. It is the responsibilities of the user to correct
such interference.

WARNING AND CAUTION
1． STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE。

Please unplug the monitor immediately if you notice any abnormal phenomena such as
smoke, strange sounds or fumes. Further use may be dangerous and can cause fire or
electric shock.

2． NEVER REMOVE THE CABINET

High voltage inside the monitor, may be electric shocked if removing cabinet.
Non-professor never remove the cabinet.

3． DO NOT PUT ANY OBJECT INTO THE MONITOR。

The ventholes of the monitor is to sink thermal. If blocked or covered, monitor maybe
damage because of overheating. Using the monitor with any object inside may cause fire,

electric shock or damage

.

4． DO NOT PLACE THE MONITOR NEAR THE WATER

The monitor maybe damage if water is inside. Do not use the monitor where water may be
splashed or spilt on the monitor as it may cause fire or electric shock.

5． PROTECT YOUR POWER CORD AND SIGNAL CABLE

Do not pull or bend the power cord and signal cable. Do not place the monitor or any other
heavy objects on the cables. If damaged, the cables may cause fire or electric shock.

6． NOTICE THE WEATHER

Do not use monitor immediately if brought it into the warm house from cold environment.
Coagulate bead may cause the monitor short circuit and damage. Before operating the
device, wait until it is absolutely dry.
Unplug the monitor while thunder!

7． PLACE THE MONITOR AT THE RIGHT PLACE

Do not place the monitor near heating source, against a bright background or duct position.
Do not make it near other electronics, such as speaks, TV. There should be more than 50
cm between two monitors. The position should be ventilation, and bright could not reach
the front, side, back of the monitor straight

.

41CD785-608-4B

3

8． CLEANING YOUR MONITOR

Do not use alcohol, ammonia based liquid, benzene, or corrosive cleanser to clean the
monitor, they may damage the cabinet or CRT’s surface. You may use soft, clouding cloth
to clean the monitor careful. Notice, you must unplug the monitor before cleaning it.

9． CARING YOUR MONITOR

Unplug the monitor when not use it for a long time. You should take the cables in hands
when lifting the monitor, or you may trip up by them and dropped the monitor.

PACKAGE

There should be the following objects in the package:
1． Monitor
2． Pedestal
3． User Manual
4． Power Cord

INSTALLATION OF MONITOR

PEDESTAL

Unplug the monitor and do like the following steps:

1. Carefully turn the monitor on its side or upside down.

2. Locate the cavities at the bottom front of the monitor.

3. Insert the pegs on the pedestal into these cavities. Push the pedestal forward until the

pedestal locks in place.

4. To remove the pedestal, hold the bottom of the pedestal, then push it out.

Install Remove

Figure 1. Installation and Removing of Pedestal

41CD785-608-4B

4

POWER CORD：

1. The monitor may work at 100---120VAC or 200---240V AC area. (No user adjustment is

required.)

2. Connect the power cord into your monitor’s power input socket, and then plug the other

end into a 3-pin AC power outlet.

Connecting the Video Cable:

cable’s 15-pin connector into the computer’s video port and tighten the two screws on the cable
connector. (See figure 2)

Caution: Don’t bend the signal cable, otherwise it will break the inner wire.

Connecting the Power Cord：Plug the power cord into the monitor’s AC power socket. Then
plug the power cord into a grounded AC outlet.

Caution：If the AC outlet is not grounded, install the proper grounding adapter (not supplied).

the monitor comes with a built-in video cable. Plug the signal

①

②

Figure 2. Connecting signal cable

1. Power Cord 2. Signal Cable

Please keep your user manual, monitor packag es on a safety place for further
using.

41CD785-608-4B

5