Lenovo LXH-GJ17L3 User Manual

Contents
CERTIFICATIONS -------------------------------------------------------------------- 2 NOTICE ---------------------------------------------------------------------------------- 2
PRECAUTIONS ---------------------------------------------------------------- 3 SPECIAL NOTES ON LCD MONITORS --------------------------------- 4
BEFORE YOU OPERATE THE MONITOR ------------------------------------- 4
FEATURES ---------------------------------------------------------------------- 4 PACKING LIST ----------------------------------------------------------------- INSTALLATION INSTRUCTIONS------------------------------------------ CONTROLS AND CONNECTORS ---------------------------------------- ADJUSTING THE VIEWING ANGLE -------------------------------------
4
5
6
7
OPERATING INSTRUCTIONS ----------------------------------------------------- 8
GENERAL INSTRUCTIONS ------------------------------------------------ HOW TO USE OSD ----------------------------------------------------------­ADJUSTING THE PICTURE -------------------------------------------­GREEN MONITOR------------------------------------------------------------ PLUG AND PLAY -------------------------------------------------------------
8
10
10-11
12
12
TECHNICAL SUPPORT(FAQ) ------------------------------------------------- 13-14
ERROR MESSAGE & POSSIBLE SOLUTION ----------------------
15
APPENDIX A SPECIFICATIONS ----------------------------------------- 16 APPENDIX B FACTORY PRESET TIMING TABLE ----------------- APPENDIX C CONNECTOR PIN ASSIGNMENT --------------------
Notice:
17
18
Please read the following words before assembling and using this monitor. Any reference to an Lenovo product, program or service is not intended to state or imply that only Lenovo ’s product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any of Lenovo’s intellectual property rights or other legally protectable rights may be used instead of the Lenovo product, program, or service. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by Lenovo, are the user’s responsibility. Lenovo may have patents or pending patent applications covering subject matter in this document. The furnishing of this document does not give you any license to these patents. Information in this document is subject to change without notice. Without the permission of Lenovo (Beijing) Limited, no part of this manual may be reproduced or distributed in any form or by any means.
®
lenovo
is a lenovo (Beijing) Limited registered trademark.
1
CE certificate
This shipped version of this device complies with the
requirements of the EEC directive 89/336/EEC “Electromagnetic compatibility” and 73/23/EEC “Low voltage directive”.
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in
order to comply with the emission limits.
1. The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.
2
PRECAUTIONS
z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen
sink, laundry tub, swimming pool or in a wet basement.
z Do not place the monitor on an unstable cart, stand, or table. If the monitor
falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
z Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.
z The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
z Cut off the power source during a lightning storm or when it will not be
used for long periods of time. This will protect the monitor from damage due to power surges.
z Do not overload power strips and extension cords. Overloading can result
in fire or electric shock.
z Never push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
z Do not attempt to service the monitor yourself, opening or removing covers
can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel.
3
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
NOTES
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time.
Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power for hours.
BEFORE YOU OPERATE THE MONITOR
FEATURES
43.2cm(17”) TFT Color LCD Monitor
Optimal Resolutions is 1280 X 1024@60Hz
Low Power Consume & Power Saving Design
Ergonomic Design
Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
1. LCD Monitor
2. Monitor’s Base
3. Owner's Manual
4. Adapter
5. Power cord
4
INSTALLATION INSTRUCTIONS
SWIVEL BASE
Install Remove
Figure 1 Installing and Removing the Swivel Base
1. During installation, place the display base the right-way up on a flat surface. Place upper part of the display slowly on to the base and wait for the click signifying that it is completely in place. Securely fasten the screw with hands or tools then secure the screws on the bottom with a screwdriver.
2. When removing the rotating base, please place the monitor upside down
taking care not to damage the LCD surface. Manually unscrew the screws then remove the display’s lower base.
Power Source:
1. Adapter use 12V DC, 4.16A.
2. Power cord user the power supply(90V-264V AC Voltage)
5
CONTROLS AND CONNECTORS Adapter
Connecting the adapter: Connect one end of the adapter to back of the
monitor and connect the other end to the power cord.
Power cord Connecting the power cord: Connect one end of the power cord to the AC
adapter and connect the other end to the power supply (90V-264V AC Voltage).
SIGNAL CABLE
Connecting the Signal Cable: the LCD monitor comes with a built-in video
cable. Plug the signal cables 15-pin connector into the computer's video port and tighten the two screws on the cable connector.
1
Figure 2 Connecting Cables
1. AC Adapter & Power cord 2. Signal Cable
6
2
+ 12 hidden pages