LENCO DVL-2010 User Manual

19.5” (49.5 cm) HD LED TV with

DVB-T/T2/S2 and DVD player

MODEL NO.: DVL-2010

USER MANUAL

1

Safety information

CAUTION:

DVD/VIDEO CD/CD PLAYER IS A CLASS 1 LASER PRODUCT. HOWEVER THIS DVD/VIDEO CD/CD
PLAYER USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION
EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DVD/VIDEO CD/CD PLAYER CORRECTLY AS
INSTRUCTED.

WHEN THIS DVD/VIDEO CD/CD PLAYER IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE
YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO
THE INSIDE OF THIS PLAYER.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS NOR REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING:

- TO PREVENT FIRE OR SHOCK HAZARD. DO NOT USE THIS POWER CORD WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE.

- TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION - LASER RADIATION WHEN OPEN, DO NOT STARE INTO BEAM.
VENTILATION WARNING - THE NORMAL VENTILATION OF THE PRODUCT SHALL NOT BE
IMPEDED FOR INTENDED USE.

The lightning flash and

arrow head within the

triangle is a warning sign

alerting you of “dangerous

voltage” inside the

product.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The exclamation mark

within the triangle is a

warning sign alerting

you of important

instructions

accompanying the

product.

Always follow basic safety precautions when using electrical products, especially when children
are present.
WARNING: To avoid the risk of electrical shock, make sure the product is unplugged from the
electrical outlet before relocating, servicing, or cleaning it.

Read all instructions before using

● Do not use this device near water.

● Clean only with a slightly damp cloth.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT INSTRUCTIONS

2

● If the cord is damaged, have it repaired by the manufacturer, its service or a similarly qualified

person in order to avoid any hazard.

● The cord should always be readily accessible.

● Don’t step on or pinch the power adaptor. Be very careful, particularly near the plugs and the

cable’s exit point. Do not place heavy items on the power adaptor, which may damage it. Keep

the entire device out of children’s reach! When playing with the power cable, they can seriously

injure themselves.

● The apparatus shall not be exposed to dripping or splashing of water or liquids and that no

objects filled with liquids such as flower vases shall be placed on the product.

● The normal ventilation of the product shall not be impeded for intended use.

● Always leave a minimum distance of 10 cm around the unit to ensure sufficient ventilation.

● Naked flame sources, such as candles, should not be placed on top of the device.

● Electrostatic discharge can disturb normal usage of this device. If so, simply reset and restart the

device following the instruction manual. During file transmission, please handle with care and

operate in a static-free environment.

● Warning! Never insert an object into the product through the vents or openings. High voltage

flows through the product and inserting an object can cause electric shock and/or short circuit

internal parts. For the same reason, do not spill water or liquid on the product.

● Do not use in wet or moist areas such as bathrooms, steamy kitchens or near swimming pools.

● Do not use this device when condensation may occur.

● Although this device is manufactured with the utmost care and checked several times before

leaving the factory, it is still possible that problems may occur, as with all electrical appliances. If

you notice smoke, an excessive build-up of heat or any other unexpected phenomena, you

should disconnect the plug from the main power socket immediately.

● The device is intended for use only in a moderate climate.

● Situate this product away from heat sources such as radiators, heat registers, stoves, or other

appliances (including amplifiers) that produce heat.

● Clean the product only as recommended by the manufacturer (see “Maintenance” section for

details). Unplug the power plug from the wall outlet before cleaning.

● Keep away from rodents. Rodents enjoy biting on power cords.

● Always hold the plug when pulling it out of the main supply socket. Do not pull the power cord.

This can cause a short circuit.

3

● Avoid placing the device on any surfaces that may be subject to vibrations or shocks.

● To protect the device during a thunderstorm, unplug the ac power adaptor.

● When the device is not in use for long periods, unplug the ac power adaptor for safety reasons.

● Unplug the power plug from the wall outlet when left unused for an extended period.

● Prevent objects/liquids from falling or spilling on the product.

● Operate the product only with the supplied power cord. Route power cords so they are not

likely to be walked on or pinched by items placed upon or against them, paying particular

attention to plugs, convenience receptacles, and the point where they exit from the product.

● This device is not intended for use by people (including children) with physical, sensory or

mental disabilities, or a lack of experience and knowledge, unless they’re under supervision or

have received instructions about the correct use of the device by the person who is responsible

for their safety.

● This product is intended for household use only and not for commercial or industrial use.

● Make sure the unit is adjusted to a stable position. Damage caused by using this product in an

unstable position or by failure to follow any other warning or precaution contained within this

user manual will not be covered by warranty.

● Never remove the casing of this apparatus.

● Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect

device shall remain readily operable.

● Do not operate this product under the following conditions.

- When the power-supply cord or plug is damaged.

- If liquid has been spilled into or objects have fallen into the product.

- If the product has been exposed to rain or water.

- If the product does not operate when used according to the operating instructions.

- If the product has been dropped or damaged in any way.

● Do not attempt to service the product; take it to the electronics repair shop of your choice for

any servicing or repair.

● Do not overload wall outlets, extension cords, or integral convenience receptacles.

● Connect this product to the power outlet which has a protective earth connection.

4

LASER SAFETY

This set employs an optical laser beam system in the CD mechanism designed
with built-in safeguards. Do not attempt to disassemble. Exposure to this
invisible laser light beam may be harmful to the human eye. This is a Class-1
laser product. Use of controls, adjustments or procedures other than those
specified herein may result in hazardous laser light beam exposure. This
compact disc player should not be adjusted or repaired by anyone except
qualified service personnel. The laser mechanism in the set corresponds to the
stylus (needle) of a record player. Although this product uses a laser pick-up
lens, it is completely safe when operated according to directions.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications. Such modifications could void the user's authority to operate the
equipment.

1) Operate turning controls and switches as instructed in the manual.

2) Before turning on the power for the first time, make sure that the power adaptor is properly

installed.

3) Store your discs in a cool area to avoid damage from heat.

Battery Handling and Usage

 Keep batteries away from children and pets. Only adults should handle batteries.
 Never throw batteries into a fire or expose them to fire or other heat sources.
 Follow the battery safety and usage instructions.

DISC Handling and Maintenance

Handling precautions

 Hold the disc by the edges so the surface will not be soiled with fingerprints. Finger prints, dirt

and scratches can cause skipping and distortion.

 Do not write on the label side with a ball-point pen or other writing utensils.
 Do not use record cleaning sprays, benzene, thinner, static electricity prevention liquids.
 Be careful not to drop or bend the disc.
 Do not install more than 1 disc on the disc compartment.
 Do not try to close the disc cover when the disc is not installed properly.
 Be sure to store the disc in its exclusive case when not in use.

If the surface is soiled

Wipe gently with a soft, damp (water only) cloth.
When wiping discs, always move the cloth from the center hole toward the outside, which will
not cause distortion. (If you wipe the discs using a circular motion, circular scratches are likely to
occur, which will cause distortion.)

If the disc is brought from a cold to a warm environment, moisture may form on the

5

disc.

Wipe this moisture off with a soft, dry, lint-free cloth before using the disc.

Improper disc storage

You can damage discs if you store them in the following places:

 Areas exposed to direct sunlight
 Humid or dusty areas
 Areas directly exposed to a heat outlet or heating appliance

User Manual
Remote Control
Power Adaptor
YPbPr Adaptor Cable

All the pictures in this manual are just for your reference, appearance and display are subject
to the final product.

ACCESSORIES

6

TABLE OF CONTENTS

GETTING STARTED

IMPORTANT INSTRUCTIONS…………………………………………………………………………………………………………….1
ACCESSORIES…………………………………………………………………………………………………………………………………..5
FEATURES………………………………………………………………………………………………………………………………………..7
GENERAL PARTS………………………………………………………………………………………………………………………………8
REMOTE CONTROL………………………………………………………………………………………………………………………..10
REMOTE CONTROL PREPARATION…………………………………………………………………………………………………12
BASIC CONNECTION……………………………………………………………………………………………………………………...13

OPERATIONS

BASIC OPERATIONS……………………………………………………………………………………………………………………….19

DVD……………………………………………………………………………………………………………………………………….…19
TV…………………………………………………………………………………………………………………………………………….26

MAIN MENU………………………………………………………………………………………………………………………………….31

FIRST TIME INSTALLATION……………………………………………………………………………………………………….…31
DTV MODE………………………………………………………………………………………………………………………………..32
ATV AND OTHER MODES……………………………………………………………………………………………………………40
SATELLITE MODE……………………………………………………………………………………………………………………….41
PC/VGA MODE………………………………………………………………………………………………………………………….45

FOR REFERENCE

MAINTENANCE……………………………………………………………………………………………………………………………..46
WALL MOUNTING…………………………………………………………………………………………………………………………46
STAND INSTALLATION…………………………………………………………………………………………………………………….47
SPECIFICATIONS…………………………………………………………………………………………………………………………….48
TROUBLESHOOTING………………………………………………………………………………………………………………………49

7

19.5" LED Display

This unit has a built-in 19.5” LED display window to provide clear vision and low
radiation.

With Built-in DVD Player

Support Auto TV Scanning

Support Digital Broadcasting Reception

Support USB Multimedia Playback

Support Multi-languages On Screen Display

Support Full Function Remote Control

Support HDMI, SCART, YPBPR, AV, VGA, PC AUDIO and CI Input

Support EARPHONE and COAXIAL Output

With Detachable Stand Holder

With TV Antenna Jack (DVB-T/DVB-T2/DVB-C)

With Satellite TV Antenna Jack (DVB-S2)

With Built-in Speakers

FEATURES

8

MAIN UNIT

1. LED display screen

2. Remote control sensor

3. Power indicator- In standby mode the indicator light is red; when switching on the unit the

indicator light is blue.

4. Stand holder

5. Disc slot- To insert a disc according to the silk screen on the side of this slot.

6. - To open or close the disc compartment.

7. - To play or pause playing (DVD).

8. VOL +/- button- To increase/decrease the volume level or move left/right.

9. CH +/- button- To select the next/previous channel or move up/down.

10. MENU button- To enter the menu setting page.

11. SOURCE button- To select the input source.

12. POWER button- To turn the TV ON/OFF.

Front View

Side View

GENERAL PARTS

9

Back View

1. Power input

2. VGA input terminal

3. PC AUDIO input terminal

4. SCART input terminal

5. RF input terminal- To connect the external Satellite TV Antenna (DVB-S2).

6. RF input terminal- To connect the external TV antenna (DVB-T/DVB-T2/DVB-C).

7. COAXIAL output terminal

8. Mini AV input terminal

9. CI+ input terminal

10. Mini YPbPr input terminal

11. EARPHONE output terminal

12. USB input terminal

13. HDMI input terminal

10

REMOTE CONTROL

1 POWER\STANDBY: Set the unit in standby mode;

press it again to switch it on.

2 MEDIA: Select USB mode.
3 : PLAY/PAUSE in TIMESHIFT and USB mode.
4 D.SETUP: Display the main disc menu.
5 : Stop playing.
6 AUDIO/LANG: Switch available soundtrack (TV); Switch

available soundtrack language (DVD).

7 S.MODE: Select the sound mode.
8 NUMBER BUTTONS (0-9): Press to select a TV channel

directly when watching TV. The channel changes after 2

seconds.

9 -/--: Switch the digits.
10 VOL +/-: Turn the volume up/down.
11 GOTO: Jump to a different chapter of the DVD.*
12 ANGLE: View DVD playback from different angles, if the

DVD has this feature.*

13 MENU: Display the main TV menu.
14 DISPLAY: Display information of the current program.
15 OK: Confirm selection.
16 ◄/►/▲/▼: Press the LEFT/RIGHT/UP/DOWN button

to navigate the on-screen menus and adjust the system

settings to your preference. Press OK to confirm your

selection.

17 SOURCE: Switch the input source.
18 D. MENU: Display the main disc menu.*
19 EXIT/TITLE: Exit from the main TV menu displayed on

the screen; Display the DVD title menu. (DVD)*

20 REPEAT: Repeat different chapters/titles or an entire

DVD.*

11

REMOTE CONTROL

21 A-B: Repeat DVD scenes of your preference.
22 CH +/-: Press to play the next or previous channel.
23 : Return to the previous channel.
24 P.MODE: Select the picture mode.
25 SUBTITLE: Enable/disable subtitles.
26 /FAV: Play the previous file; Display the favorite

channels list.

27 : Play next file.
28 : Move fast backward.
29 : Move fast forward;
30 TV/RADIO: Switch the unit between TV and radio;

Open or close the disc compartment. (DVD)*

12

REMOTE CONTROL PREPARATION

BATTERY INSTALLATION

Install the batteries as the following pictures. Be sure that the + and – terminals are
positioned as indicated in the battery compartment (Fig1).

SERVICE LIFE OF BATTERIES

- The batteries normally last for one year although this depends on how often the remote

control is used.

- If the remote control fails to work even when it is operated near the player, replace the

batteries.

- Use two size AAA dry batteries.

NOTE:

 Do not drop, step on or otherwise impact the remote control. This may damage the parts

or lead to malfunction.

 If the remote control is not going to be used for a long time, remove the batteries.

REMOTE CONTROL
OPERATION

Point the remote control from no more
than about 6m from the remote control
sensor and within about 60° of the front
of the player (Fig2).

NOTES:

- The operating distance may vary

according to the brightness of the
room.

- Do not point the bright light at the

remote control sensor.

- Do not place objects between the

remote control and the remote
control sensor.

- Do not use this remote control while

simultaneously operating the remote
control of any other equipments.

Fig1

Fig2

Remote Control

Sensor

Push

Open
Press

13

 Ensure all the cables are disconnected from the main unit before connecting to an AC power

source.

 Read through the instructions before connecting other equipment.

CONNECTING TO AC POWER SOURCE

CONNECT EXTERNAL ANTENNA TO UNIT

Install external antenna into antenna jack for best picture.

To power outlet

AC Adaptor

Antenna

Outdoor
antenna
amplifier

Indoor antenna

amplifier

Power plug of
antenna
amplifier

75 OHM
antenna plug

BASIC CONNECTION

14

HDMI CONNECTION

PC/VGA CONNECTION

HDMI cable
(Not included)

Use the HDMI cable to connect the unit with

other devices to receive a high-definition

multimedia signal.

Back of DVD/VCR

Back of PC

Use the VGA cable and Audio cable to

connect the unit with TV or PC, and use

this product as a monitor.

VGA cable
(Not included)

Audio cable

(Not included)

15

SCART CONNECTION

AV (COMPOSITE VIDEO) CONNECTION

Back of DVD/VCR

SCART cable
(Not included)

Back of DVD/VCR

For basic connection, use the composite
Audio L/R (white/red) and CVBS (yellow)
cable to connect the unit with other

devices.

AV cable
(Not included)