Legrand NV-CTP36-V2 User Manual

NuVo Technologies LLC Hebron, KY USA

otechnologies.com

w.nuv

CTPIGv2 1133

NV-CTP36-V2 Color Touch Screen

Installation Guide

NV-CTP36 NuVo Technologies

En55024 En55022 Class-B

- Consult the dealer or an experienced radio/TV technician for assistance.

which the receiver is connected.

- Connect the equipment into an outlet on a circuit different from that to

- Increase the separation between the equipment and receiver.

- Reorient or relocate the receiving antenna.

measures:

Level Pencil Measuring device (ruler, tape measure) Cutting tool (drywall saw, utility knife) DB9 Serial Cable (Grand Concerto only) USB-A to USB-B Cable (Renovia only) USB-A to Mini-B pin USB cable Phillips Screwdriver Additional Tools Needed-

Touch Pad mounting plate 1

NV-CTP36 -V2 Color Touch Pad, 3.6” display 1 SKU Description Quantity

NV-CTP36 Package Contents

to try to correct the interference by one or more of the following determined by turning the equipment off and on, the user is encouraged harmful interference to radio or television reception, which can be will not occur in a particular installation. If this equipment does cause radio communications. However, there is no guarantee that interference accordance with the instructions, it may cause harmful interference to and can radiate radio frequency energy and, if not installed and used in interference in a residential installation. This equipment generates, uses, are designed to provide reasonable protection against harmful Class B digital device, pursuant to Part 15 of the FCC Rules. These limits This equipment has been tested and found to comply with the limits for

FCC Radio Frequency Interference Statement Warning

Step 1- Download NuVo Software

For proper functionality the newest firmware is required. To install the current Configurator software and NV-CTP36-V2 firmware visit nuvotechnologies.com/prozone. Select the Dealer Resource Center icon. Enter your user name and password and then select the Software Download link. Select SW-I8G/E6G to download the programming software if using a Grand Concerto, or SW-RV if using Renovia. Next select SW-CTP36-V2 and download the NV-CTP36V2 firmware (it will be a zipped file).

Fig. A

Fig. B

Step 2- Write your Configuration

The Color Touch Pad needs a zone address assigned through the NuVo Configurator programming software. If the CTP36-V2 is used to control one amplified zone, address the control pad to that specific zone number.

If multi-zone control is desired, create two zones for the CTP36-V2. First, give it an address in the amplified zone in which it is located. Next, add an additional address in a non-audio zone (Grand Concerto numbers 17-20, Renovia numbers 13-15 & 17-20). The software will request the CTP36-V2 be slaved to an audio zone. Click the “Slave to” drop down menu and select the audio zone labeled previously.

Step 3- Wire Run

If you are replacing an existing NuVo Control Pad you may skip this step. Otherwise run CAT5 wire from the location of the NuVo Grand Concerto EZPort to the desired location of the Color Touch Pad. Terminate each end of the CAT5 with an RJ45 connection in a 568a configuration. Plug the CAT5 cable into an open RJ45 port on the back of the EZPor t (Fig. A).

If using the NV-CTP36-V2 with the Renovia in-wall zone amplifier, a simple wire run from the Zone Amp’s NuVoNet connection to the Color Touch Pad’s location is necessar y (Fig. B), or from the NuVoNet connection on the Freestanding Zone Amplifier (Fig. C).

Step 4- NuVoNet Connection

Connect the CAT5 cable to the RJ45 connection labeled NuVoNet on the back of the CTP36-V2 (Fig. D).

Step 5- Mounting the CTP36-V2

The CTP36-V2’s location should be at an average eye level for the user. It is designed to be installed in a standard dual gang pre-construction or “old works” mounting ring or box. First mount the metal mounting ring included with the CTP36-V2 package into the installed wall mud ring or low-voltage box. Second, screw the CTP36-V2 into the metal mounting ring (Fig E).

Step 6- Update the Firmware

First, update your Grand Concerto or Renovia system by uploading the configuration file. Place a DB9 serial cable between your laptop and the programming port on the back of the Grand Concerto (Fig. F). Note that most newer laptops do not include a serial port, so a USB to Serial cable will be necessary. If updating a Renovia system you will use a USB cable (Fig. G). Open the Configurator software and upload your configuration file to the system.

ZONE 7&8

SYS ON

EXT. MUTE

VARIABLE OUTPUT

TIP=L RING=R

FIXED

OUTPUT

CONNECT TO

NV-I8EZP1

USE NV-NC1

CABLE

NETWORK DIGITAL LINK

Fig. E

Fig. F

RS-232

PROGRAM

CONNECT TO

NV-I8X

USE NV-SLC1

CABLE

USE CNLY WITH 250V FUSE

MODEL NV-I8DM

SIX SOURCE EIGHT ZONE

AUDIO DISTRIBUTION SYSTE M

120V 60Hz 500W NuVo Technologies Cincin nati Ohio USA

www.nuvotechnolog ies.com

CONFORMS TO

UL STD.6500

CERTIFIED TO

CAN/CSA STD.E6006 5

3033118

Fig. C

FU S E:

Fig. H

Fig. D

Fig. G

Fig. I

Next you will update the firmware on the NV-CTP36. Locate the software downloaded in Step 1, and unzip the file. Using a USB-A to Mini-B cable, connect your laptop to the USB connection on the front of the NV-CTP36 (Fig. H). Run the Color Touch Pad software, called CTP36Loader.exe. Follow the on-screen prompts to update the firmware on the NV-CTP36.

Step 7- Address the Color Touch Pad

The last step is to address the NV-CTP36. When configuring this system with the NuVo Configurator software you should have labeled, in the zone tab, a name for this control pad. Select that name from the list (Fig. I).

If using the Color Touch Pad for multi-zone control select the zone name addressed in the non-audio zone in step 2, not the amplified zone. Next, press the Home button. Press the Tool icon in the bottom right and choose Touchscreen Options from the available list. Check Multi-zone Control to enable Multi-room control from the Color Touch Pad.

Recalibration

To re-calibrate the touch sensing of the screen, press the Reset button, then press and hold the Power button while the Color Touch Pad starts. Follow the on-screen instructions.

Restore Defaults

To restore the Color Touch Pad to factory defaults, press the Reset button then press and hold the Volume Up button at startup.