Legrand AU7396 User Manual
INSTRUCTION/INSTALLATION SHEET
lyriQ™ SINGLE SOURCE 4 ZONE
301 Fulling Mill Road, Suite G
Middletown, PA 17057
Phone (800) 321-2343 / Fax (717) 702-2546
www.onqlegrand.com
1. Introduction
The On-Q /Legrand lyriQ™ Single Source 4
Zone Audio Distribution Hub, PN AU7396 (see
Figure 1), is an integral part of the lyriQ™ Audio
System. It is a component which, when
combined with other essential components and
your source equipment receiver, CD player, etc,
creates a versatile whole-house audio system
that will fill your rooms with high-quality sound
for years to come. Category 5 technology is a
new, innovative method of providing high quality
audio to remote locations with a single 8conductor cable such as Category 5. This
technology provides many advantages over
other conventional methods of audio distribution
such as simple, single Category 5 wiring
scheme, and infrared control of system
components.
2. Description
All components of the lyriQ™ Audio System are wired centrally from the lyriQ™ Audio Distribution Hub located
within the structured wiring enclosure. In addition to providing a central point of connection, the Hub distributes
the necessary voltage to power the system. The lyriQ™ Flush Mount Single Source Input and lyriQ™ Volume
Controls connect directly to the module utilizing RJ-45 connections. The system can support multiple modules
through “daisy chaining” the Audio Distribution Hubs.
NOTE: The single bay bracket shown in Figure 1 (P/N 364890-01) is included with the Audio Distribution
Hub.
NOTE: The 24 volt, 2.5 amp Power Supply (P/N PW1060) is not included and must be purchased
separately.
3. Installation
Installation of the On-Q/Legrand lyriQ™ Single Source 4 Zone Audio Distribution Hub and related components,
is best accomplished at multiple times during new construction, at “Rough-in” before the drywall is installed, and
at “Trim-out” after the drywall is installed and painted.
IMPORTANT: Read the manuals that are included with all associated lyriQ™ Audio products before
installation of any single component! If you are unsure of any of the following installation procedures
contact On-Q/Legrand Technical Support @ 1-800-321-2343 option 1 or contact an On-Q/Legrand
installer.
NOTE: The lyriQ™ Audio Distribution Hub provides power to all of the components of the lyriQ™ Audio
System.
AUDIO DISTRIBUTION HUB
IS-0320 REV. C
Figure 1
Page 1 of 2
©Copyright 2007 by On-Q/Legrand All Rights Reserved.
INSTRUCTION/INSTALLATION SHEET
lyriQ™ SINGLE SOURCE 4 ZONE
301 Fulling Mill Road, Suite G
Middletown, PA 17057
Phone (800) 321-2343 / Fax (717) 702-2546
www.onqlegrand.com
NOTE: To provide ultimate flexibility for future products, run two Category 5 cables from the location of
the lyriQ™ Flush Mount Single Source Input to the lyriQ™ Single Source 4 Zone Audio Distribution Hub.
Also, run a 16/2 or 16/4 speaker cable, along with the Category 5 cable, from the lyriQ™ Single Source 4
Zone Distribution Hub to each volume control location.
A. “Rough-in” steps:
1. Run a Category 5 cable from the room location containing the lyriQ™ Flush Mount Single Source Input
(typically the entertainment center location) to the lyriQ™ Audio Distribution Hub located in the
Enclosure.
2. Run Category 5 cables from the room locations containing the lyriQ™ Volume Controls to the lyriQ™
Audio Distribution Hub located in the Enclosure.
B. “Trim-out” steps:
NOTE: Make sure that the Power Supply is not connected to the Distribution Hub.
1. Install one or more lyriQ™ Audio Distribution Hubs in the enclosure by first attaching the Hubs to
their included brackets using the 4 corner plungers. Then insert the bracket tabs into the slots on
the left of the enclosure and use the bracket push-pin to secure each Hub to the enclosure.
2. Terminate all Category 5 cables with RJ-45 plugs using the T568A wiring standard.
3. Connect the lyriQ™ Flush Mount Single Source Input AUDIO OUT jack via a Category 5 cable to
the SOURCE IN jack of the lyriQ™ Audio Distribution Hub (see Figure 2).
4. Connect the Category 5 cables coming from the room locations containing the lyriQ™ Volume
Controls to the Zone Output jacks on the lyriQ™ Audio Distribution Hub (see Figure 2).
5. If applicable, connect additional lyriQ™ Audio Distribution Hubs together by connecting a Category 5
jumper cable from the CASCADE OUT jack on one Hub to the SOURCE IN jack on the other Hub.
6. Plug the 24 volt power supply cable into the Power jack on the lyriQ™ Audio Distribution Hub.
7. Verify system functionality.
AUDIO DISTRIBUTION HUB
IS-0320 REV. C
Figure 2
Page 2 of 2
©Copyright 2007 by On-Q/Legrand All Rights Reserved.
Loading...