All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, electronic, mechanical,
As part of Land Rover environmental policy, this publication is printed on paper made from chlorine free pulp.
recording or other means without prior written permission from Land Rover.
Page 2
WWW.MANUALS.WS
WWW.MANUALS.WS
Introduction
This handbook covers all derivatives in the Freelander range available at the date of publication and,
together with the other publications in the literature pack, provides the information you will need to
derive maximum pleasure from owning and driving your new vehicle.
For your convenience, the handbook is divided into sections, each dealing with a different aspect of
the vehicle. These are listed on the following page and you will find it worthwhile to take a little time
to read each one, and get to know your Freelander as soon as you possibly can. The more you
understand before you drive, the greater the satisfaction once you are seated behind the steering
wheel.
*An asterisk appearing within the text, identifies features or items of equipment that are either
optional, or are only fitted to some vehicles in the model range.
IMPORTANT
The specification of each vehicle will vary according to territorial requirements and also from model
to model within the vehicle range. Some of the information published in this handbook, therefore,
may not apply to your particular vehicle.
Land Rover operates a policy of constant product improvement and therefore reserves the right to change specifications without
notice at any time. Whilst every effort is made to ensure complete accuracy of the information in this handbook, no liabilities for
inaccuracies or the consequences thereof can be accepted by the manufacturer or the dealer, except in respect of personal injury
caused by the negligence of the manufacturer or the dealer.
2
Page 3
WWW.MANUALS.WS
WWW.MANUALS.WS
OWNER’S HANDBOOK SUPPLEMENT
The following information should be read in conjunction with the
Owner's Handbook, Part number LRL0672/1, and provides information
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, electronic, mechanical,
recording or other means without prior written permission from Land Rover.
1
Page 4
WWW.MANUALS.WS
WWW.MANUALS.WS
Bulb Replacement
Bulb Replacem ent
SIDELIGHTS
2
1
H5222
NOTE:The sidelight bulb replacement
information shown on page 228 of the Owner’s
Handbook is no longer applicable.
3
2
Page 5
WWW.MANUALS.WS
WWW.MANUALS.WS
Bulb Replacement
FRONT SIDE LIGHT/DIRECTION
INDICATOR
AB C
When replacing the access panel, insert the top
first, then lower the panel slightly so that the
bottom edge slots securely onto the wheel arch
liner.
To replace the fastener, push the centre pin out
of the fixing (as condition ‘C’), then locate the
fastener through the access panel and into the
wheelarch liner. Finally, push the centre pin into
the fastener until it lies flush with its body as
condition ‘A’.
H5242
The front side/direction indicator lights are
reached through an access panel in the wheel
arch liner. To release the panel, first remove the
fixing shown in the upper inset.
1. Push the centre pin of the fastener ‘A’ in
upper inset, firmly into its body (as
condition ‘B’).
2. Prise the fastener from the access panel.
3. Holding the curved tab, push the access
panel upwards (as arrowed in main
illustration). This will enable the panel to
be removed.
Check the operation of all exterior lights before
you use the vehicle.
IMPORTANT
Before replacing a bulb, always switch off
the ignition switch and appropriate lighting
switch to prevent any possibility of a short
circuit. Only replace bulbs with the same
type and specification.
Replacement bulbs
NOTE: All bulbs must be rated at 12 volts
BulbWatts
3
2
H5227
1. Remove the three Torx (size 20) screws
securing the light unit to the body and
withdraw the light unit.
Disconnect the electrical connectors from
the light unit if necessary.
2. Twist the bulb holder anti-clockwise and
pull to release from the light unit.
3. Twist the bulb anti-clockwise and pull to
remove from the holder.
NOTE: When refitting the light unit, ensure that
the foam seal is correctly positioned between
the light unit and body.
Headlights low beam55 H7
Headlights high beam55 H7
Front marker lights5
Side lights/Direction indicators5/21
Front fog lights
Reverse lights21
Rear marker/fog guard lights5/21
Tail/Stop lights5/21
High mounted stop light21
Number plate light5
Interior courtesy lights10
Map reading lights5
Glovebox light5
Loadspace light10
Vanity mirror light3
NOTE: In certain territories it is a legal
requirement to carry spare bulbs, in case of
bulb failure. A replacement bulb kit is available
as an approved accessory from your Land
Rover Retailer.
*
55 H11
4
Page 7
WWW.MANUALS.WS
WWW.MANUALS.WS
Contents
Using The Remote Handset . . . . . . . . . . . . 5
Your vehicle may be configured for Single Point
Entry. This personal security feature unlocks
only the driver’s door and disarms the alarm
when the handset unlock button (1) is pressed
once.
To unlock all the remaining doors, press the
handset button a second time.
Your Land Rover Retailer can disable Single
Point Entry so that a single press of the handset
button will open all doors and disable the alarm
see ‘Single point entry’, page 35.
1
H5298
Locking
Press the lock button (2) once to lock all doors
and arm the alarm system.
If an opening (door, tailgate, hood etc) is not
closed properly, the vehicle horn will sound a
warning see ‘Mislock’, page 34.
2
5
Page 10
WWW.MANUALS.WS
WWW.MANUALS.WS
Quick Overview
FASCIA CONTROLS
1234
76 5
H5141
1. Exterior mirror control
2. Lighting and direction indicator controls
3. Windscreen wiper/washer controls
4. Heater/Air conditioning controls
NOTE: This is a brief overview of the fascia controls. For further details please refer to ‘FASCIA
CONTROLS’, page 30.
5. Ignition switch
6. Cruise control switches
7. Steering column adjustment lever
6
Page 11
WWW.MANUALS.WS
WWW.MANUALS.WS
Quick Overview
INSTRUMENT PANEL
231
H5111
1. Tachometer
2. Coolant temperature gauge
3. Speedometer
NOTE: This is a brief overview of the instrument panel, for more information, please refer to
‘INSTRUMENT PANEL’, page 58.
54
4. Digital display
5. Fuel gauge
7
Page 12
WWW.MANUALS.WS
WWW.MANUALS.WS
Quick Overview
WARNING LIGHTS
32
41
5
H5110
1. Service engine soon (AMBER).
2. Low oil pressure (RED).
3. Service engine (AMBER).
4. Airbag SRS (RED).
NOTE: This is a brief overview of the warning lights, for more information concerning warning light
functionality, please refer to ‘INSTRUMENT PANEL’, page 61.
7
6
5. ABS (AMBER).
6. Parking brake & brake system (RED).
7. Battery charging (RED).
8
Page 13
WWW.MANUALS.WS
WWW.MANUALS.WS
Quick Overview
LIGHTS & INDICATORS
Direction indicators
2
1
H5094
1. Side, tail and instrument panel lights
2. Headlights
Headlight high, and low beams
H5093
Move the lever DOWN to indicate a LEFT turn,
and UP to indicate a RIGHT turn.
NOTE: For further information concerning
operation of the lights, please refer to
‘DIRECTION INDICATORS’, page 65.
H5095
Pull the lever fully towards the steering wheel to
change headlight beams.
9
Page 14
WWW.MANUALS.WS
WWW.MANUALS.WS
Quick Overview
WIPERS & WASHERS
The wipers and washers will only operate when
the ignition switch is turned to position ‘I’ or ‘II’.
3
Variable delay (intermittent wipe)
2
1
H5096
1. Intermittent wipe
2. Normal speed wipe
3. Fast speed wipe
Single wipe
Pull the lever down and release immediately.
H5098
Rotate the inner switch to vary the delay
between wipes.
Windshield washers
H5099
Pull the lever towards the steering wheel. The
windscreen wipers will operate in conjunction
with the washers.
NOTE: For further information concerning
operation of the wipers and washers, please
refer to ‘WINDSCREEN WIPERS’, page 68 and
‘WINDSCREEN WASHERS’, page 69.
10
Page 15
WWW.MANUALS.WS
WWW.MANUALS.WS
Quick Overview
CENTRE CONSOLE SWITCHES - 5 DOOR
Automatic model illustrated
1. Heated front screen*
2. Heated rear screen
1
2
3
7
4
5
6
3. Heated driver’s seat
4. Air conditioning
5. Recirculated air supply
6. Heated passenger’s seat
7. Hill Descent Control
8. Parking brake
9. Sunroof
10. Electric taildoor glass
*
*
*
8
9
H5142
10
11
Page 16
WWW.MANUALS.WS
WWW.MANUALS.WS
Quick Overview
CENTRE CONSOLE SWITCHES - 3 DOOR
Automatic model illustrated
1. Heated front screen*
2. Heated rear screen
1
2
3
7
4
5
6
3. Heated driver’s seat
4. Air conditioning
5. Recirculated air supply
6. Heated passenger’s seat
7. Hill Descent Control
8. Parking brake
9. Driver’s window control
10. Passenger’s window control
11. Interior locking switch
12. Electric taildoor glass
*
*
8
9
11
H5235
10
12
12
Page 17
WWW.MANUALS.WS
WWW.MANUALS.WS
Quick Overview
HEATER CONTROLS
456
3
7
2
1
H5063
1 & 9. Heated front seats*
Press to heat the driver's or front passenger
seat. Press a second time to switch off.
2. Heated rear window
Press to defrost or demist the rear screen.
3. Heated front screen
Press to defrost or demist the screen.
*
4. Air distribution control
Rotate to select air distribution:
Air to face vents.
Air to face vents and foot outlets.
Air to foot outlets.
Air to foot outlets and windscreen.
All air to windscreen.
5. Air blower control
6. Air temperature control
7. Air conditioning
8
9
8. Air recirculation button
Press to recirculate air inside the vehicle.
NOTE: For further information concerning operation of the heater controls, please refer to ‘HEATER
CONTROLS’, page 85.
13
Page 18
WWW.MANUALS.WS
WWW.MANUALS.WS
Quick Overview
AUDIO SYSTEM CONTROLS
15
12
14
13
3
12
4
11
10
ICE 1518
1. CD compartment
2. Display
3. CD mode button
4. News information
5. Waveband selector
6. Sound mute
7. Pre-set/CD buttons
8. Search/CD track controls
KSAN FM
898
7
9. Memory store button
10. Fader and balance control
11. On/off and volume control
12. Tone control
13. CD load button (Multichanger only)
14. CD eject button (Multichanger only)
15. CD eject button
FM1 - 1
97.90
NEWS
5
6
14
Page 19
WWW.MANUALS.WS
WWW.MANUALS.WS
Quick Overview
NAVIGATION SYSTEM CONTROLS*
12456789
ON
Info
3
TP
NAVIGATION SYSTEM
CD
RadNav
OK
NAVISYS
111210
ICE 1419
1. On/off
2. Tone
3. Display
4. Traffic programme
5. Security light
6. CD mode selection
NOTE: Please refer to your ‘In-Car Entertainment’ and ‘Navigation’ handbooks for further details.
NOTE: Some music CD manufacturers are using data encryption to 'copy-protect' their recordings
and prevent the production of pirate copies. These CD's differ from the internationally agreed CD
audio standard, RedBook, a standard that serves as the operating basis for all CD players and
changers.
Copy-protected CD's may not play in your Audio unit or CD changer or may be played subject to
various limitations, e.g., sound quality may be impaired.
7. Radio mode selection
8. Navigation mode selection
9. Display/CD eject
10. Right rotary control
11. Multifunction buttons
12. Left rotary/volume control
If you do experience a problem, try the CD in other players before contacting the CD vendor.
15
Page 20
WWW.MANUALS.WS
WWW.MANUALS.WS
Gas Station Information
Gas Station Guide
Gas Station Inform ation
Fuel filler
The fuel filler is located in the rear right-hand
fender.
Insert the key in the lock, turn it anti-clockwise
and allow any pressure inside the tank to
escape, before removing the cap
NOTE: The key cannot be removed from the
filler cap unless the cap is correctly positioned
in the filler neck.
H5115
Fuel Type
Gasoline vehiclesUnleaded 95RON (87RON minimum)
NOTE: For more detailed information, see ‘FUEL FILLING’, page 113.
16
Page 21
WWW.MANUALS.WS
WWW.MANUALS.WS
Gas Station Information
Opening the bonnet
1. From inside the vehicle, pull the bonnet
release handle located on the right hand
side of the fascia at knee height.
2. Lift the bonnet safety catch lever and raise
bonnet.
3. Support the bonnet in the raised position
with the bonnet stay.
Engine oil top up
Gasoline vehicles - 2.5 litre V60W/40, 5W/40 or 5W/50 oil to API service
Cooling system top up
All vehicles50% mix of fresh water and ethylene glycol
1
H5261
level SJ or ACEA A3 specification.
based anti freeze (containing no methanol).
3
2
NOTE: For more detailed information, see ‘HOOD OPENING’, page 177.
Tire pressures
Air pressure naturally increases in warm tires (after the vehicle has been driven for a while). if you
have to check warm tires, you should expect the pressures to have increased between 4 and 6 psi
(30 and 40 kPa). In this circumstance, NEVER let air out of the tires in order to match the
recommended pressures.
Loading conditionPressure - psi/kPa
All driving conditions (all tire sizes)Front & Rear30/206
NOTE: For more detailed information, see ‘TIRE PRESSURES’, page 248.
If you believe that your vehicle has a defect
which could cause a crash, or could cause
injury or death, you should immediately inform
the National Highway Traffic Safety
Administration (NHTSA), in addition to
notifying Land Rover North America Inc.
If NHTSA receives similar complaints it may
open an investigation. If it subsequently finds
that a safety related defect exists in a group of
vehicles, it may order a recall and remedy
campaign.
However, NHTSA cannot become involved in
individual problems between you and your
retailer and/or Land Rover North America.
AUTO SAFETY HOTLINE
To contact NHTSA, you may call the Auto Safety
HOTLINE toll free at 1-800-424-9393 (or
202-366-0123 in the Washington D.C. area) or
write to: NHTSA, U.S. Department of
Transportation, Washington, DC20590.
WARNING LABELS ATTACHED TO THE
VEHICLE
Warning labels attached to your vehicle
bearing this symbol mean: DO NOT
touch or adjust components until you
have read the relevant instructions in
the handbook.
CALIFORNIA PROPOSITION 65 WARNING
WARNING
Engine exhaust, some of its constituents, and
certain vehicle components, contain or emit
chemicals known to the State of California to
cause cancer and birth defects or other
reproductive harm. In addition, certain fluids
contained in vehicles, and certain products of
component wear contain or emit chemicals
known to the State of California to cause
cancer and birth defects or other reproductive
harm.
WARNING
Battery posts, terminals, and related
accessories contain lead and lead
compounds. Wash hands after handling.
Safety warnings are included in this
handbook. These indicate a procedure which
must be followed precisely in order to reduce
the risk of personal injury.
WARNING
Warning labels showing this symbol
indicate that the ignition system utilises
very high voltages. DO NOT touch any
ignition components while the ignition
switch is turned on.
21
Page 26
WWW.MANUALS.WS
WWW.MANUALS.WS
Before You Drive
SYMBOLS USED
The following symbols used within the
handbook call your attention to specific types of
information.
This recycling symbol identifies those
items that must be disposed of safely in
order to prevent unnecessary damage to the
environment.
This symbol identifies those features that
can be adjusted or disabled/enabled by a
Land Rover Dealer/Authorised Repairer.
WARNINGS IN THIS HANDBOOK
WARNING
Safety warnings are included in this
handbook. These indicate either a procedure
which must be followed precisely, or
information that should be considered with
great care in order to avoid the possibility of
personal injury or serious damage to the
vehicle.
BEFORE YOU DRIVE
WARNING
Your vehicle has a higher ground clearance
and, hence, a higher centre of gravity than
ordinary passenger cars. This will result in
different handling characteristics.
Inexperienced drivers should take additional
care, particularly in off-road driving
situations and when performing abrupt
manoeuvres on unstable surfaces.
Various labels are fixed inside the engine
compartment, the number, position, and
content of which may vary from model to
model. The illustration above locates the labels
of specific importance, and is included for
guidance only.
• Air conditioning label
• Engine oil label
• Keep clear of rotating parts
• Emission control label
NO ENGINE ADJUSTMENT REQUIRED
CATALYST
THIS VEHICLE CONFORMS TO U.S. EPA REGULATIONS APPLICABLE TO 2004 MODEL YEAR NEW INTERIM NON TIER 2
BIN 8 LIGHT-DUTY TRUCKS AND CALIFORNIA REGULATIONS APPLICABLE TO 2004 MODEL YEAR NEW LEV 1 ULEV
EQUIVALENT LIGHT DUTY TRUCKS
EPA APPROVED
I/M TESTING EXEMPTION
LOADED I/M TESTING OF
PERMANENT FOUR WHEEL DRIVE
OR TRACTION CONTROL EQUIPPED
VEHICLES MUST BE CONDUCTED ON
A FOUR WHEEL DRIVE SPEED
SYNCHRONISED DYNAMOMETER
OTHERWISE NONLOADED TEST
PROCEDURE MUST BE PERFORMED
OBD II CERTIFIED
CAUTION / ATTENTION
USE ONLY APPROVED
5W-40 OR 5W-50 FULL
SEE HANDBOOK
FOR SPECIFICATIONS
UTILISER UNIQUEMENT DE L'HUILE
MOTOR SYTHETIQE APPROUVEE
5W-4- OU 5W-50
CONSULTER LE MANUEL
DU CONDUCTEUR POUR
LES SPECIFICATIONS
VACUUM ROUTING DIAGRAM
FUEL TANK
CHARCOAL
CANISTER
BAC000803
PURGE
VALVE
23
Page 28
WWW.MANUALS.WS
WWW.MANUALS.WS
Before You Drive
SUN VISOR LABELS
PASSENGER AIRBAG LABELS
WARNING:
!
HIGHER ROLLOVER RISK
Avoid Abrupt Maneuvers
and Excessive Speed.
Always Buckle Up.
See Owner's Manual
For Further Information
AIR BAG AND
ROLLOVER
WARNINGS
FLIP VISOR OVER
WARNING
Children Can Be KILLED or INJURED
by Passenger Air Bag
The back seat is the safest place for children 12 and under.
Make sure all children use seat belts or child seats.
H5247
H4032
Take note of the warnings concerning the
airbag SRS, and risk of vehicle rollover.
Take note of the warning concerning the airbag
SRS and safe seating of small children.
24
Page 29
WWW.MANUALS.WS
WWW.MANUALS.WS
Before You Drive
IN AN EMERGENCYANTI-THEFT PRECAUTIONS
IMPORTANT
Remember the breakdown safety code
If a breakdown occurs while travelling:
• Wherever possible, consistent with
road safety and traffic conditions, the
vehicle should be moved off the main
thoroughfare, preferably into a lay-by. If
a breakdown occurs on a motorway,
pull well over to the inside of the hard
shoulder.
• Switch on hazard lights.
• If possible, position a warning triangle
or a flashing amber light at an
appropriate distance from the vehicle to
warn other traffic of the breakdown,
(note the legal requirements of some
countries).
• Consider evacuating passengers
through nearside doors onto the verge
as a precaution in case your vehicle is
accidentally struck by other traffic.
While it may be difficult to deter the
‘professional’ car thief, the majority of thefts are
carried out by opportunists.
Therefore, take vehicle security very seriously
and ALWAYS adopt this simple ‘four point drill’
whenever you leave your vehicle - even for just
a few minutes:
1. Fully close all the windows (and the
*).
sunroof
2. Remove your belongings (or hide them
from view).
3. Remove the starter key.
4. Superlock the vehicle using the remote
handset.
Thieves are attracted by vulnerable vehicles.
Even if you have followed the ‘four point drill’
there is still much that you can do to make your
vehicle a less inviting target.
• Park your vehicle where it will be clearly
visible to householders and passers-by.
• At night park in well-lit areas, and avoid
deserted or dimly-lit side streets.
• NEVER leave the keys in the vehicle.
• Do not keep important documents (or spare
keys) in the vehicle - these are a real bonus
for the thief.
You have been supplied with a pair of identical
keys and two remote control handsets.
WARNING
Keep the spare key in a safe place - NOT IN
THE VEHICLE.
The keys supplied with your vehicle are
programmed to the vehicle's security system they CANNOT be reprogrammed and the engine
cannot be started without a valid programmed
key. If a key is lost or broken, a replacement can
be ordered only from a Land Rover Retailer.
NOTE: Land Rover Retailers do not stock spare
keys, time has to be allowed for replacements
to be programmed to your security system and
then delivered to the retailer.
If you lose a key, contact your Land Rover
Retailer; a key reported lost will be deactivated.
If the key is later recovered, your Land Rover
Retailer can have it reactivated.
29
Page 34
WWW.MANUALS.WS
WWW.MANUALS.WS
Fascia Controls
Fascia Controls
FASCIA CONTROLS
14
15
16
12119
1013
18
468375
22
191721
2
1
20
30
23
H5138
Page 35
WWW.MANUALS.WS
WWW.MANUALS.WS
Fascia Controls
1. Exterior mirror control
2. Lighting and direction indicator controls
3. Horn
4. Tachometer
5. Fuel gauge
6. Coolant temperature gauge
7. Speedometer
8. Horn
9. Windscreen wiper/washer controls
10. Clock display
11. Hazard warning switch
12. Audio system
13. Heater/Air conditioning controls
14. Gear lever
15. Hill descent control
16. Ignition switch
17. Remote cruise control switches
18. Remote audio controls
19. Parking aid system switch
20. Cruise control master switch
21. Parking brake
22. Centre console switches (3 Door shown)
NOTE: The precise specification and location of
the controls may vary according to territorial
requirements and from model to model within
the vehicle range.
*
31
Page 36
WWW.MANUALS.WS
WWW.MANUALS.WS
Locks & Alarm
H
Locks & Alarm
STEERING COLUMN LOCK
3522
To unlock the steering column
Insert the key FULLY and turn the ignition
switch to position ‘I’. A small movement of the
steering wheel may be necessary to disengage
the steering lock while turning the switch.
To lock the steering column
Turn the key to position ‘0’ and withdraw it from
the ignition switch. Turn the steering wheel
slightly until the lock engages.
WARNING
Once the steering lock has engaged, it is
impossible to steer the vehicle. DO NOT
remove the key or turn the ignition switch to
position ‘0’ while the vehicle is in motion.
ALARM SYSTEM
Your vehicle is fitted with a sophisticated
electronic anti-theft alarm and engine
immobilisation system. In order to ensure
maximum security and minimum
inconvenience, you are strongly advised to gain
a full understanding of the alarm system, by
thoroughly reading this section of the
handbook.
LOCKING THE VEHICLE AND ARMING THE
ALARM
Before locking the vehicle and arming the
alarm, ensure that all doors (including taildoor),
windows, sunroof and bonnet apertures are
securely closed.
There are three methods for securing your
vehicle:
• ‘Superlocking’ using the handset (recommended high security method).
• ‘Superlocking’ using the key.
• Locking using the key.
IMPORTANT
• If passengers or animals are to be left
inside, DO NOT lock the vehicle using
the handset - movement inside the
vehicle may activate interior space
protection
sound.
• FOR MAXIMUM SECURITY ALWAYS
SUPERLOCK THE VEHICLE USING THE
REMOTE HANDSET
*, causing the alarm to
32
Page 37
WWW.MANUALS.WS
WWW.MANUALS.WS
Locks & Alarm
Using the remote handset
Locking
With the remote handset:
1
H5023
While it is not necessary to point the handset at
the vehicle, the handset must be within range of
the vehicle when a button is pressed. Note that
the operating range may vary depending upon
handset battery condition and may sometimes
be limited by physical and geographical factors
beyond your control. From a security point of
view, it may not be wise to unlock unless you
are in close proximity to the vehicle.
H5024
Press the lock (padlock symbol (1) button
once. Each time the vehicle is locked using the
handset, a coded signal is transmitted to a
receiver inside the vehicle, which activates the
following security features:
• the central door locking system (all the door
locks are activated).
• ‘Superlocking’ - the door locks cannot be
operated from inside the vehicle.
• the perimetric alarm (protects the door,
taildoor, and hood apertures).
If the doors lock correctly, the direction
indicator lights flash three times to confirm that
the vehicle is secure and the anti-theft alarm
indicator light (in the instrument panel) will
start to flash rapidly.
Once armed, the alarm will sound if any door is
opened.
33
Page 38
WWW.MANUALS.WS
WWW.MANUALS.WS
Locks & Alarm
With the key:
Insert the key and turn the door lock towards
the rear of the vehicle. Turning the key ONCE
activates the following:
• all doors locked (not superlocked)
• perimetric alarm activated (protects the
doors, bonnet and taildoor)
NOTE: Interior space protection
activated.
Turning the key TWICE within 1 second
activates, in addition to the above:
• Superlocking
If the doors lock correctly, the direction
indicators flash three times to confirm that the
vehicle is secure and the anti-theft alarm
indicator light (in the instrument panel) will
start to flash rapidly.
NOTE: The engine will automatically be
immobilised after the ignition switch has been
turned off.
* is not
Superlocking
Provided all the doors are fully closed, the
Superlocking feature is activated automatically
whenever the vehicle is locked using the remote
handset. Superlocking immobilises the interior
door handles, thereby preventing an intruder
from gaining entry by smashing a window and
reaching inside the vehicle to operate the door
handles.
WARNING
For safety, NEVER use Superlocking if
passengers are to remain inside the vehicle in an emergency they would not be able to
escape.
Mislock
If one of the doors, taildoor or hood are not
properly closed when the alarm is armed, a
mislock occurs (the horn will sound a warning).
The alarm will still be armed and the engine
immobilised, but the open aperture will not be
protected. If the appropriate aperture is then
closed, the alarm will fully arm without the need
to press the lock button again unless the
driver's door is open, in which case the alarm
will be fully armed by pressing the lock button
again.
If the taildoor glass is left open when the alarm
is armed, the horn will sound as a reminder, but
the vehicle will be locked and alarmed as
normal. The taildoor glass can be closed from
outside the vehicle using the ignition key in the
taildoor (see ‘Raising and lowering’, page 78).
34
Page 39
WWW.MANUALS.WS
WWW.MANUALS.WS
Locks & Alarm
Anti-theft alarm indicator light
H5026
After locking, the RED indicator light on the
instrument panel flashes rapidly while the alarm
is arming itself.
After approximately 10 seconds, the indicator
light adjusts to a slower frequency, and
continues to flash as an anti-theft deterrent
until the alarm is disarmed.
Unlocking
With the remote handset:
If your vehicle has been configured with the
Single Point Entry security feature, and was
locked with the handset, the handset unlocks
the vehicle in two stages:
• Press the unlock (no padlock) button once
to disarm the alarm and unlock the driver's
door only (see ‘Single point entry’, page 35).
• Press the unlock button twice to disarm the
alarm and unlock ALL the doors.
If your vehicle has not been configured with
Single Point Entry, all the doors will unlock at
the first press. In either case, the direction
indicators flash once and the interior lights
illuminate.
With the key:
Turn the key towards the front of the vehicle.
The alarm will be fully disarmed. To re-mobilise
the engine, the key must be inserted into the
ignition switch.
If the alarm sounds
If the alarm is triggered, it will sound for
approximately 30 seconds before switching
itself off and can be triggered up to ten times
in total before needing to be reset.
To silence the alarm, press either handset
button, or operate the door locks using the key
in the driver's door.
Single point entry
This is a personal security feature, which
enables the driver's door only to be unlocked,
leaving the other doors in a locked state. It can
be operated by the remote handset as follows:
Press the unlock button once to unlock the
driver's door, press a second time to unlock the
remaining doors and taildoor.
Single point entry can be disabled by a
Land Rover Retailer.
35
Page 40
WWW.MANUALS.WS
WWW.MANUALS.WS
Locks & Alarm
Interior locking switch - 5 door vehicles
Interior locking switch - 3 door vehicles
H5027
H5237
This is a personal security feature which allows
the driver (or passenger) to lock (or unlock) all
the doors from inside the vehicle (while driving
or with the vehicle stationary). Press the lower
part of the switch to lock (the alarm will not be
armed), and the upper part to unlock.
H5030
This is a personal security feature which allows
the driver (or passenger) to lock (or unlock) all
the doors from inside the vehicle (while driving
or with the vehicle stationary). Press the
padlock symbol part of the switch to lock (the
alarm will not be armed), and the unlocked
padlock symbol to unlock.
NOTE: If interior locking has been activated,
pull the interior door handle once to unlock, and
twice to open the door.
NOTE: If interior locking has been activated,
pull the interior door handle once to unlock, and
twice to open the door.
36
Page 41
WWW.MANUALS.WS
WWW.MANUALS.WS
Locks & Alarm
Door handles and door sill locking buttons
From inside the vehicle, each door can be
individually locked by depressing (arrowed in
illustration) the appropriate door sill button.
However, doors cannot be unlocked by raising
the sill button.
CHILD-PROOF LOCKS
H5029
On 5-door models, move the lever on the rear
doors down (arrowed in illustration) to engage.
With the child-proof locks engaged, the rear
doors cannot be opened from inside the
vehicle, thereby avoiding the risk of a door
H5035
being opened accidentally while the vehicle is
moving.
Use the door handles to unlock, as follows:
• First operation of the door handle unlocks
the door.
• Second operation of the door handle opens
the door.
NOTE: The door handles will not open the doors
if the vehicle has been superlocked (see
‘Superlocking’, page 34)
NEVER leave children unsupervised in the
vehicle.
WARNING
37
Page 42
WWW.MANUALS.WS
WWW.MANUALS.WS
Locks & Alarm
ENGINE IMMOBILISATION
Engine immobilisation is an important aspect of
the security system and is designed to
safeguard the vehicle from theft, should the
driver forget to lock the doors. Engine
immobilisation prevents the engine from being
started unless a valid key is inserted into the
ignition switch, and occurs automatically after
the ignition switch has been turned off.
The engine is re-mobilised by a signal to the
ignition switch transmitted from a transponder
contained within the key head. This occurs
automatically whenever a valid key is inserted
into the ignition switch and turned to position
‘I’.
WARNING
DO NOT keep more than one ignition key or
keys from other vehicles on the same key
ring, because the engine may not re-mobilise
automatically.
DOOR LOCKING CUT-OFF SWITCH
H5033
An inertia switch, which operates when the
ignition switch is in position ‘II’, prevents the
doors from centrally locking (or, if the doors are
already locked, unlocks them) in the event of an
accident or sudden impact. If this occurs,
central locking will be inhibited until either:
• the ignition switch is turned off and the
driver’s door has been opened and closed,
or:
• the driver’s door has been opened and
closed, and the inertia switch is reset.
The inertia switch is located inside the engine
compartment on the left hand side, beneath and
to the rear of, the engine compartment fuse
box. The switch must be reset before the engine
can be restarted. Reset the switch by pressing
the rubber top (arrowed in illustration).
This will also reset the fuel system, see ‘FUEL CUT-OFF SWITCH’, page 114).
38
Page 43
WWW.MANUALS.WS
WWW.MANUALS.WS
Locks & Alarm
Always check for fuel leaks before resetting
the switch. Activating the switch when the
fuel system has been damaged will cause
additional fuel leakage, increasing the risk of
fire or personal injury.
WARNING
REMOTE HANDSET
WARNING
The handset contains delicate electronic
circuits and must be protected from impact,
water damage, high temperatures, humidity,
direct sunlight, the effects of solvents, waxes
and abrasive cleaners.
When the battery needs replacing, it will be
apparent from the following symptoms:
• A gradual deterioration in range and
performance.
• The alarm buzzer and the anti-theft alarm
indicator light will double bleep/flash every
second, for ten seconds, after the alarm is
disarmed and driver's door opened.
It is recommended that you fit a Land Rover
YWX10003L or a Panasonic CR2032
replacement battery (available from a Land
Rover Retailer).
39
Page 44
WWW.MANUALS.WS
WWW.MANUALS.WS
Locks & Alarm
Battery replacement
Handset re-synchronisation
If the handset fails to lock or unlock the car, this
may be because the coded signal transmitted
by the handset, and the signal expected by the
alarm control unit are no longer synchronised.
To re-synchronise the handset, operate either
button of the handset at least five times in quick
succession (in close proximity to the vehicle).
H5025
1. Carefully prise the handset apart, start
from the keyring end using a small coin or
screwdriver. Avoid damaging the seal
between the two halves of the case and DO
NOT allow dirt or moisture to get inside
the handset.
2. Slide the battery out of its clip, taking care
to avoid touching the circuit board or the
contact surfaces of the clip.
3. Press and hold each button in turn for at
least five seconds (this will drain any
residual power from the handset).
4. Fit the new battery, ensuring that correct
polarity is maintained (‘+’ side facing up).
Finger marks will adversely affect battery
life; if possible, avoid touching the flat
surfaces of the battery and wipe them
clean before fitting.
5. Press the two halves of the handset firmly
together and ensure that both halves are
fully joined to prevent dirt or moisture
from entering the handset.
6. Re-synchronise the handset.
The handset is now ready for use.
40
Page 45
WWW.MANUALS.WS
WWW.MANUALS.WS
Seats
Seats
FRONT SEATS
WARNING
To avoid the risk of losing control of the
vehicle and sustaining personal injury, DO
NOT adjust the driver's seat or head restraint
while the vehicle is in motion.
DO NOT travel with the seat backs reclined
steeply rearwards. Optimum benefit is
obtained from the seat belt with the seat back
reclined to a maximum 30 degrees from the
upright (vertical) position.
SITTING CORRECTLY
o
max. 30
• Adjust the head restraints so that the top of
the head restraint is level with the upper
portion of the head.
• The seat belt should rest in the centre of the
shoulder. The lap part should fit tightly
across the hips and not on the stomach.
• Do not move the front seat too close to the
instrument panel. The driver should hold the
steering wheel with slightly bent arms. The
legs should also be slightly bent so that the
pedals can be pressed to the floor.
WARNING
Both driver, and front seat passenger should
adjust their seat to provide the maximum
practical distance from the airbags to prevent
injury should the airbags be deployed.
H4767
The seats, head restraints, seat belts, and
airbags all contribute to the protection of the
occupants. Optimal use of these components
will give you more protection. Therefore,
observe the following points:
• Sit in the most upright position with the
base of your spine as far back as possible
and the backrest not reclined more than 30
degrees.
41
Page 46
WWW.MANUALS.WS
WWW.MANUALS.WS
Seats
2
3
FRONT SEAT ADJUSTMENT
Head restraints are designed to support the
4
5
back of the head (NOT THE NECK), and to
restrain rearward movement of the head in
the event of a collision. The top of the
restraint must be positioned level with the top
of the head to be effective.
Head restraint removal
Turn the right hand mounting (5) a quarter turn
anti-clockwise and pull the restraint upwards.
After replacing a head restraint, turn the
right-hand mounting clockwise.
H5233
Forward/backward adjustment
Lift the lever (1) and slide the seat into position.
Make sure that the seat is locked in position
before driving.
Backrest adjustment
Rotate the handwheel (2) to adjust.
1
DO NOT drive with the head restraints
removed from occupied seats.
WARNING
WARNING
Lumbar support adjustment
(Driver's seat only)
Rotate the handwheel (3) to increase or
decrease support to the lumbar region of the
back.
Head restraint adjustment
Raise or lower the restraint (4) until the top of
the cushion is level with the top of the head.
42
Page 47
WWW.MANUALS.WS
WWW.MANUALS.WS
Seats
Backrest release lever (3-door models)
HEATED FRONT SEATS
*
H5234
To enable rear seat passengers to enter or exit
the vehicle, lift the backrest release lever
upwards to fold the front seat backrest
forwards.
After the backrest has been returned to its
normal, upright position, ensure that it is
securely retained by attempting to pull it
forward again, but without operating the
release lever. There should be no appreciable
movement.
The rear seat access lever also acts as a seat
belt presenter, improving access to the seat belt
(see ‘Seat belt presenter (3-door models)’, page 48).
WARNING
Ensure that the backrest is secure before
driving.
H5070
With the engine running, press the switches to
operate the heating elements in either the
driver's or front passenger seat (the indicator
light in the switch illuminates). Press a second
time to switch off.
NOTE: The seat heaters will switch off
automatically 45 seconds after the ignition
switch is turned off, or either front door is
opened.
The seat heaters are thermostatically controlled
and operate intermittently to achieve and then
maintain a predetermined temperature between
o
F and 97oF (26oC and 36o°C).
79
NOTE: The operating temperature will drop to
50oF (10oC) during the operation cycle.
NOTE: Owners should be aware that the seat
heaters consume considerable power from the
battery and for this reason, it is recommended
that they are operated only with the engine
running.
43
Page 48
WWW.MANUALS.WS
WWW.MANUALS.WS
Seats
H
REAR SEATS
Folding the rear seats
On vehicles not fitted with 60/40 split rear seats
the whole seat can be folded forwards to
increase luggage space. On vehicles fitted with
60/40 split rear seats, either or both parts of the
seat can be folded.
NOTE: Before folding the rear seats, ensure that
the centre rear seat belt is unbuckled.
WARNING
Ensure that the rear seat backrests are
securely latched in the upright position when
the seat is in use and when loads are carried
in the luggage area.
DO NOT carry unsecured equipment, tools or
luggage that could move causing personal
injury in the event of an accident or
emergency manoeuvre. Where possible, use
the seat belts to secure luggage carried on the
seats.
Accommodating long loads
Remove the head restraints from the front
passenger and rear seats (see ‘Head restraint removal’, page 42), move the front passenger
seat forwards as far as possible and fully recline
the seat backrest. Finally, fold the rear seat
backrest (or the appropriate part of the backrest
in the case of 60/40 split seats) fully forward as
shown.
Loads that are too long to be carried inside the
vehicle should be carried on the roof. (See
‘ROOF RACK’, page 153).
If it is necessary to carry a load that protrudes
through the taildoor, or taildoor window, be
aware of any territorial regulation restricting the
length of any such load. In addition, ensure that
loads DO NOT rest on the glass of a partially
open window. Damage to the glass or window
mechanism may occur.
WARNING
3366
Lift the release levers (see inset) to release the
backrest (lift both levers simultaneously on
vehicles without 60/40 split seats) and fold the
backrest forwards.
WARNING
You are advised NOT to carry loads which
require driving with the taildoor, or taildoor
window open, as poisonous fumes will be
drawn into the vehicle. If driving the vehicle
in this condition is unavoidable, switch the
heater to face level vents with all vents open,
close the sunroof
air blower to position 4.
44
* and windows, and turn the
Page 49
WWW.MANUALS.WS
WWW.MANUALS.WS
Seats
H
H
Maximum luggage space
‘Latch secure’ indicator
3333
3332
To create extra luggage space:
1. Lift the seat release levers to release the
backrest and fold the seat backrest
forward.
2. Tip the whole seat assembly forward as
shown in illustration and readjust the front
seats as required.
To return the seats to their normal position;
push the seat base release levers (shown in
lower inset) rearwards to unlock the seat base
and unfold the seats. Ensure the seat backrests
are properly secured by attempting to push
them forwards - there should be no movement.
WARNING
It is extremely dangerous to ride in the cargo
area. In a collision, anyone riding in this area
is more likely to be injured or killed. Do not
allow anyone to ride in any area of your
vehicle that is not equipped with seats and
safety belts. Be sure that everyone in your
vehicle is in a seat and using a safety belt
properly.
A ‘latch secure’ indicator, mounted on the top of
the right hand side of the rear seat backrest, will
pop up showing a red band, when the catch is
released.
When returning the seat to the upright position,
ensure the indicator drops back into the
backrest and that the red band is no longer
visible - this confirms that the larger portion of
the backrest is secure.
NOTE: The ‘latch secure’ indicator does NOT
indicate that the smaller portion of the 60/40
split backrest is secure - this must be checked
individually.
NOTE: When returning the seats to the upright
position, ensure that the seat belts are not
trapped.
45
Page 50
WWW.MANUALS.WS
WWW.MANUALS.WS
Seat Belts
Seat Belts
SEAT BELT SAFETY
WARNING
In a collision, occupants not wearing a seat
belt can be thrown around inside, or possibly
thrown out of the vehicle. This is likely to
result in more serious injuries than would
have been the case had a seatbelt been worn.
It may even result in the loss of life.
Seat belts fitted to your vehicle are designed for
adults and larger children. Each belt should be
used by one occupant only.
Observe the following precautions:
• Ensure ALL passengers are securely
strapped in at all times, using the
appropriate restraint - even for the shortest
journeys.
• ALWAYS adjust seat belts to eliminate any
slack in the webbing. DO NOT slacken the
webbing by holding the belt away from the
body - to be fully effective, the seat belt
must remain in full contact with the body at
all times.
• ALWAYS fit the lap strap as low on the hips
as possible (never across the abdomen),
and ensure that the diagonal belt passes
across the shoulder without slipping off or
pressing on the neck.
• DO NOT wear seat belts over hard, sharp or
fragile items in clothing, such as pens, keys,
spectacles etc.
• Always replace a seat belt assembly that has
withstood the strain of a severe vehicle
impact, or if the webbing shows signs of
fraying.
• Where possible use the seat belts to secure
large items of luggage that are to be carried
on the seats - in the event of an accident,
unsecured items become flying missiles
capable of causing serious injury.
• DO NOT use a seat belt that is twisted or
obstructed in any way that could impede its
smooth operation.
• DO NOT allow front seat occupants to travel
with the seat backs reclined steeply
rearwards. Optimum benefit is obtained
from the seat belt with the seat back angle
reclined to a maximum of 30 degrees from
the upright (vertical) position.
• DO NOT allow foreign matter (particularly
sugary food and drink) to enter the seat belt
locks - such substances can render the
locks inoperative.
• In most countries, all occupants are
required by law to wear a seat belt, unless
they have been issued with a medical
exemption certificate.
WARNING
The airbag supplementary restraint system
(see ‘Airbag SRS’) is designed to enhance the
overall effectiveness of the seat belts. It does
not replace them. SEAT BELTS MUST
ALWAYS BE WORN.
Ensure that all seat belts are worn correctly an improperly worn seat belt increases the
risk of death or serious injury in the event of a
collision.
46
Page 51
WWW.MANUALS.WS
WWW.MANUALS.WS
Seat Belts
H
PREGNANT WOMEN
WARNING
Pregnant women must wear a correctly
positioned seat belt; it is safer for mother and
unborn child.
SEAT BELTS
To minimise injury in the event of an accident,
it is important that seat belts are worn correctly.
Read the instructions below and the advice
contained under the heading ‘SEAT BELT SAFETY’, page 46.
There are many ways that the belt can be
misused for the sake of comfort, but there is
only one way of wearing it safely.
During pregnancy, women should wear the lap
belt across the hips below the baby, with the
diagonal belt passing across the shoulder,
between the breasts and to one side of the baby
- if in doubt, consult a doctor.
Fastening the seat belts
3303
Inertia reel belts are fitted to all front and rear
seating positions.
Draw the belt over the shoulder and across the
chest and, ensuring that the webbing is not
twisted, insert the metal tongue plate into the
buckle nearest the wearer - a ‘CLICK’ indicates
H5157
Never place anything between you and the seat
belt in an attempt to cushion the impact in the
event of an accident. It can be dangerous and
reduce the effectiveness of the seat belt in
preventing injury.
that the belt is securely locked.
NOTE: The centre rear seat belt tongue plate will
not latch into either of the outer seating position
buckles.
Seat belts are designed to bear upon the bony
structure of the body (pelvis, chest and
shoulders) and can only be worn safely with the
seats in a near upright position - DO NOT allow
front seat occupants to travel with the seat
steeply reclined.
NOTE: Where possible, rear seat passengers
should adjust their position on the seat to
enable the seat belt webbing to cross the
shoulder without pressing on the neck.
47
Page 52
WWW.MANUALS.WS
WWW.MANUALS.WS
Seat Belts
H
H
Releasing the belt
Press the RED button on the seat belt buckle.
Front seat belt upper anchorage adjustment
(5-door models)
Seat belt presenter (3-door models)
3304
The rear seat access lever can be used as a seat
belt presenter to improve accessibility of the
front seat belts.
2344A
The height of the seat belt upper anchorage can
be adjusted for comfort AND safety. Adjust the
height of the seat belt anchorage point by
pressing the button (arrowed in illustration)
and sliding the anchor up or down. For safety,
the seat belt should always be worn with the
webbing crossing the shoulder MIDWAY
BETWEEN THE NECK AND SHOULDER.
Ensure the anchorage has ‘clicked’ into one of
the locked positions before driving, and DO
NOT adjust the height once the vehicle is in
motion.
48
Page 53
WWW.MANUALS.WS
WWW.MANUALS.WS
Seat Belts
SEAT BELT PRE-TENSIONERS
The seat belt pre-tensioners activate in
conjunction with the airbag SRS and provide
additional protection in the event of a severe
frontal impact on the vehicle (see ‘HOW THE AIRBAG SRS WORKS’, page 54). The
pre-tensioners automatically tighten the seat
belts fitted to the front seats. This reduces any
slack in both the lap and diagonal portions of
the belts, thereby reducing forward movement
of the belt wearer in the event of a severe frontal
collision.
The airbag SRS warning light on the instrument
panel will alert you to any malfunction of the
seat belt pre-tensioners.
If the pre-tensioners have been activated, the
seat belts will still function as restraints, and
must be worn in the event that the vehicle
remains in a driveable condition.
NOTE: The seat belt pre-tensioners will NOT be
activated by rear, side or minor frontal impacts.
WARNING
After the seat belt pre-tensioners have been
activated once, they MUST BE REPLACED by a
Land Rover Retailer. Failure to replace the
pre-tensioners will reduce the efficiency of
the vehicle's front restraint systems.
After any frontal impact, always have the seat
belts and pre-tensioners checked and, if
necessary, replaced by a Land Rover
Retailer.
In the interests of safety, it is recommended
that removal or replacement of the front seats
and seat belts should be carried out only by a
Land Rover Retailer.
Second row seat belt locking mechanism
The second row seat belts have a special
locking mechanism which aids the retention of
child seats. The procedure to install a child seat
is as follows:
1. Install the child seat in the vehicle, attach
the seat belt and secure the buckle in
accordance with the manufacturers fitting
instructions.
2. Pull on the shoulder section of the belt to
unreel all of the remaining webbing to the
limit of its travel. This will engage the
automatic locking feature, which then acts
as a ratchet, allowing the webbing to
retract ONLY.
3. Allow the seat belt to retract onto the child
seat (a ‘clicking’ sound will confirm that
the ratchet has engaged), while firmly
pushing the child seat into the vehicle
seat.
4. Ensure there is no slack in the seat belt by
pulling upwards on the shoulder belt
immediately above the child restraint. The
seat belt should now be locked and the
child seat held firmly in position.
Once the child seat is removed and all the seat
belt webbing is allowed to retract, the seat belt
locking mechanism reverts to normal
operation.
NOTE: Where possible, use the seat belt
automatic locking mechanism to secure large
items of luggage that are to be carried on the
seats - in the event of an accident, insecure
items become flying missiles capable of
causing serious injury.
49
Page 54
WWW.MANUALS.WS
WWW.MANUALS.WS
Seat Belts
Service information
DO NOT attempt to service, repair, replace,
modify or tamper with any part of the
pre-tensioner and airbag SRS, or wiring in the
vicinity of a pre-tensioner or airbag SRS
component; this could cause the system to
activate, resulting in personal injury.
Afterfifteen years from the original date of
registration (or the installation date of a
replacement pre-tensioner), some components
will need to be replaced by a Land Rover
Retailer.
In addition, ALWAYS contact your retailer if:
• an airbag inflates.
• a pre-tensioner activates.
• the front or side of the vehicle is damaged,
even if the pre-tensioner has not activated.
WARNING
CARING FOR SEAT BELTS
Regularly inspect the belt webbing for signs of
fraying, cuts and wear; also pay particular
attention to the condition of the fixing points
and adjusters.
DO NOT bleach or dye the webbing and avoid
contaminating the webbing with polish, oil or
chemicals (see ‘Seat belts’, page 203).
Testing inertia reel belts
• With the seat belt fastened, give the
webbing near the buckle a quick upward
pull. The buckle must remain securely
locked.
• With the seat belt unfastened, unreel the
webbing to the limit of its travel. Check that
unreeling is free from snatches and snags
and then allow the belt to FULLY retract.
• Partially unreel the webbing, then hold the
tongue plate and give it a quick forward pull.
The mechanism must lock automatically
and prevent any further unreeling.
If a seat belt should fail any of these tests,
contact your dealer immediately.
Always replace a seat belt that shows signs of
webbing damage or has withstood the strain
of a severe vehicle impact.
WARNING
50
Page 55
WWW.MANUALS.WS
WWW.MANUALS.WS
Child Restraints
Child Restraints
CHILD SAFETY SEATS
Seat belts fitted to your vehicle are designed for
adults and larger children. It is very important
that all infants and children under 12 are
restrained in a suitable child safety seat
appropriate to their age and size (see table).
Child safety seats approved for use in your
vehicle are available from Land Rover Retailer.
Only fit a child safety seat of a type approved for
the specific seating positions in your vehicle
(see table), and ensure the seat manufacturer's
fitting instructions are followed exactly.
WARNING
Do not attempt to fit a child safety seat in the
central rear position on 3-door vehicles fitted
with only four seats.
For optimum safety, children should travel in
the rear of the vehicle at all times; front
passenger seat travel is NOT recommended.
However, if a passenger airbag is fitted and it is
ESSENTIAL that a child travels in the front, set
the vehicle seat fully rearward and seat the child
in an approved FORWARD-FACING child seat.
DO NOT use a rear-facing child seat - an
inflating airbag could impact with the seat and
cause serious injury.
The above symbol affixed to the passenger side
fascia panel of your vehicle, warns against the
use of a REAR-FACING child safety seat in the
front passenger seat, when a passenger airbag
is fitted. This type of seat could cause serious
injury to a child in the event of an airbag
deployment.
DO NOT install a rear-facing child safety seat
in a passenger seat equipped with an airbag
system. Failure to follow this advice could
result in serious injury, or even death, for the
child in the event of an airbag deployment.
WARNING
51
Page 56
WWW.MANUALS.WS
WWW.MANUALS.WS
Child Restraints
NOTE: Child restraint information given in the
table is correct at time of going to press.
However, availability of child restraints may
change. Please refer to your retailer for the
latest information.
Mass Group
(As displayed on Child Restraint
packaging)
0 = Up to 10 kg (0-9 months)XULL
0+ = Up to 13 kg (0-18 months)XULL
I = 9 to 18 kg (9 months - 4 years)UF**ULL
II & III =15 to 36 kg (4-12 years)UF**ULL
U = Suitable for ‘universal’ category restraints approved for this mass group.
L = Suitable for particular child restraints as listed below.
UF = Suitable for Forward Facing ‘universal’ category restraints approved for this mass group.
X = Not suitable for child restraints in this mass group.
Group 0 - BRITAX Rock-A-Tot.
Group 0+ - BRITAX Rock-A-Tot.
Group I - BRITAX Renaissance
Group II & III - BRITAX Horizon Booster.
NOTE: Seating positions marked ** will accept ‘universal’ seats provided that the seat back is
positioned vertically.
WARNING! Do not install a rear facing child restraint in a passenger seat equipped with an airbag
system.
.
Passenger
All vehicles
Seating Positions
Front
Rear
Outboard 2
seater
Rear
Outboard 3
seater
Rear Centre
52
Page 57
WWW.MANUALS.WS
WWW.MANUALS.WS
Airbag SRS
Airbag SRS
H5204
AIRBAG SRS
The airbag supplementary restraint
system (SRS) provides additional
protection for the driver and front
seat passenger, in the event of a severe frontal
impact on the vehicle.
WARNING
The airbag is a supplementary restraint
system that provides ADDITIONAL protection
in a frontal impact only - it does NOT replace
the need to wear a seat belt. For maximum
safety protection in all crash situations, a
seat belt must be worn.
Provided the front seat occupants are correctly
seated, with seat belts properly worn, the
airbags will provide additional protection to the
chest and facial areas in the event of the vehicle
receiving a severe frontal impact.
NOTE: Inflation and deflation of the airbags
takes place very quickly and will not protect
against the effects of secondary impacts that
may occur.
The airbag(s) are located in the centre pad of
the steering wheel and in the fascia panel above
the glovebox (see illustration).
Do not allow a front seat passenger to
obstruct the operation of the airbag by placing
feet, knees or any other part of the person, or
any other objects in contact with, or in close
proximity to, an airbag module.
DO NOT attach or position items to or on an
airbag cover (steering wheel centre pad or
fascia panel), which could interfere with the
inflation of the airbag or, if the airbag
inflates, be propelled inside the car causing
injury to the occupants.
WARNING
WARNING
53
Page 58
WWW.MANUALS.WS
WWW.MANUALS.WS
Airbag SRS
To ensure correct deployment of the airbags, it
is essential that obstructions are not allowed to
intervene between an airbag and the occupant.
The following are examples of the type of
obstructions that could either, impede correct
operation of the airbags, or jeopardise personal
safety in the event of an airbag deployment:
• Accessories attached to or obscuring an
airbag cover.
• Items of hand luggage, or other objects
placed on an airbag cover.
• Feet, knees or any other part of the anatomy
in contact with, or in close proximity to, an
airbag cover.
Seating positions
In order to provide optimum protection in the
event of a severe frontal impact, it is necessary
for the airbags to deploy with considerable
speed.
An inflating airbag can cause facial abrasions
and other injuries if the occupant is too close to
the airbag at the time of its deployment.
WARNING
To reduce the risk of accidental Injury from
inflating airbags, seat belts should be
correctly worn at all times. In addition, both
driver and front seat passenger should adjust
their seat to provide the maximum practical
distance from the airbags.
HOW THE AIRBAG SRS WORKS
In the event of a severe frontal impact, the
airbag control unit monitors the rate of
deceleration induced by the collision, to
determine whether the airbags should be
deployed.
Operation of the airbag SRS is dependent
entirely on the rate at which the vehicle's
passenger compartment changes speed as a
result of a collision. The circumstances
affecting different collisions (vehicle speed,
angle of impact, type and size of object hit, for
example), vary considerably and will affect the
rate of deceleration accordingly.
NOTE: The airbag SRS is not designed to
operate as a result of rear collisions, minor
frontal or side impacts or roll-over accidents;
nor will it operate as a result of heavy braking or
driving over bumps and potholes.
It follows, therefore, that significant superficial
damage can occur without the airbags
deploying or, conversely, that a relatively small
amount of structural damage may cause the
airbags to be deployed.
NOTE: Airbags will only deploy when they are
required to supplement the restraining force of
the seat belts.
In the case of a severe frontal collision, both
front airbags and seat belt pre-tensioners will
be deployed.
54
Page 59
WWW.MANUALS.WS
WWW.MANUALS.WS
Airbag SRS
After inflation, some airbag components are
hot - DO NOT touch until they have cooled.
Airbag SRS warning light
The light illuminates as a bulb and system
check when the ignition switch is turned to
H5206
Airbag inflation is virtually instantaneous and
occurs with considerable force, accompanied
by a loud noise. The inflated bag, together with
the seat belt restraint system, limit the
movement of a front seat occupant, thereby
reducing the risk of injury to the head and upper
torso.
WARNING
An inflating airbag can cause facial abrasions
and other injuries. Minimise the risk of injury
by ensuring that front seat occupants are
wearing their seat belts and are seated
correctly, with the seat as far back as is
practical.
position ‘II’ and will extinguish after
approximately five seconds.The airbag SRS
should always be checked by a dealer if any of
the following symptoms occurs:
• The warning light fails to illuminate when
the ignition switch is turned to position ‘II’.
• The warning light fails to extinguish within
approximately five se conds after the ignition
switch is turned to position ‘II’.
• The warning light illuminates after the
engine is started, or while the vehicle is
being driven.
WARNING
A warning light mounted on the
instrument panel will alert you to
any malfunction of the airbag SRS.
When an airbag inflates, a fine powder is
released. This is not an indication of a
malfunction. However, the powder may cause
irritation to the skin and should be thoroughly
flushed from the eyes and any cuts or abrasions
of the skin. After inflation the airbags deflate
immediately. This provides a gradual
cushioning effect for the occupant and also
ensures that the driver's forward vision is not
impaired.
55
Page 60
WWW.MANUALS.WS
WWW.MANUALS.WS
Airbag SRS
SERVICE INFORMATION
DO NOT attempt to service, repair, replace,
modify or tamper with any part of the airbag
SRS, or wiring in the vicinity of an airbag SRS
component; this could cause the system to
activate, resulting in personal injury.
After fifteen years from the original date of
registration (or the installation date of a
replacement airbag SRS), the airbag modules
will need to be replaced by a Land Rover
Retailer.
In addition, ALWAYS contact your Retailer if:
• an airbag inflates.
• the front of the vehicle is damaged, even if
the airbag has not inflated.
• any part of an airbag module cover (the
steering wheel centre pad or fascia panel)
shows signs of cracking or damage.
WARNING
The components that make up the airbag
SRS are sensitive to electrical or physical
interference, either of which could easily
damage the system and cause inadvertent
operation or a malfunction of the airbag.
For your safety it is recommended that you
seek the assistance of a Land Rover
Retailer to carry out any of the following:
• Removal or repair of any wiring or
component in the vicinity of any of the
SRS components, including the
steering wheel, steering column,
instrument and fascia panels.
• Installation of electronic equipment
such as a mobile phone, two-way radio
or in-car entertainment system.
• Modification to the front of the vehicle,
including the bumper and chassis.
• Attachment of accessories to the front
of the vehicle.
IMPORTANT
Disposing of vehicles
If you sell your vehicle, be sure to inform the
new owner that the vehicle has an airbag SRS.
In addition, make sure the new owner is aware
of the airbag module replacement date.
If your vehicle is to be scrapped; airbags that
have not been deployed are potentially very
dangerous and must be safely deployed in a
controlled environment by qualified personnel,
before a vehicle is scrapped.
56
Page 61
WWW.MANUALS.WS
WWW.MANUALS.WS
Steering Column
Steering Column
STEERING COLUMN ADJUSTMENT
H5084
The angle of the steering column can be
adjusted to suit your driving position:
1. With the vehicle stationary, push the
locking lever fully down to free the
steering column.
2. Move the steering wheel (up or down) into
the desired position, making sure that the
instrument panel is clearly visible.
3. When adjustment is complete, pull the
locking lever fully up to lock the steering
column in position.
WARNING
DO NOT adjust the steering column while the
vehicle is in motion. This is extremely
dangerous.
DO NOT drive the vehicle unless the locking
lever is in the locked position (fully up).
57
Page 62
WWW.MANUALS.WS
WWW.MANUALS.WS
Instruments
Instruments
INSTRUMENT PANEL
2341
H5102
1. Tachometer
Indicates engine speed in revolutions per
minute (x 1000). To protect the engine from
damage, NEVER allow the tachometer pointer
to enter the RED sector.
2. Temperature gauge
This gauge indicates the temperature of the
engine coolant. As the engine warms up, the
pointer will rise to the mid-point of the gauge,
where it should remain while the engine is
operating at its normal temperature.
If the pointer reaches the RED sector, the
coolant is too hot and severe engine damage
could result; stop the vehicle as soon as safety
permits and seek qualified assistance.
98765
3. Over-temperature warning light
Illuminates when the engine coolant
temperature reaches the RED sector (248
o
120
C). Illuminates as a bulb check when the
ignition switch is turned to position ‘II’ and
extinguishes when the engine is started.
4. Speedometer
Indicates road speed in miles per hour and
kilometres per hour.
5.Trip recorder reset button
When the ignition switch is turned on, the
display shows either the odometer reading or
the trip recorder reading. By pressing the trip
recorder reset button briefly, the display will
change between the trip recorder and odometer
modes. With the trip recorder mode displayed,
press and hold the reset button for 2 seconds to
reset the display to zero.
Pressing the button with the ignition off, will
display the odometer reading for 5 seconds.
o
F
58
Page 63
WWW.MANUALS.WS
WWW.MANUALS.WS
Instruments
6. Digital display
A
B
C. External temperature reading. Displays the
temperature outside of the vehicle whilst
in motion. The ‘snowflake’ symbol will
appear to the left of the temperature
reading when the outside temperature
drops below 39
NOTE: The temperature reading will remain
static whilst the vehicle is stationary.
For further information concerning the
automatic transmission, (see ‘CommandShift®
TRANSMISSION’, page 115).
7. Temperature unit change
Pressing the button will toggle the temperature
display between Celsius (
o
F).
(
o
F (4oC).
o
C) and Fahrenheit
8. Fuel gauge
The pointer indicates the fuel level when the
C
H5104
The panel displays the following:
A. Odometer reading (shows the total
distance travelled by the vehicle). The
word ‘ODO’ is displayed.
Trip recorder (for recording individual
journey distances). The word ‘TRIP’ is
displayed instead of ‘ODO’.
B. Automatic gear selector position (‘1’, ‘2’,
‘4’, ‘P’, ‘R’, ‘N’, ‘D’) - automatic
transmission only.
The word ‘SPORT’ confirms the selection
of Sport mode - automatic transmission
only.
Manual mode gear selection information
(‘1’, ‘2’, ‘3’, ‘4’ or ‘5’) - automatic
transmission onl.y
ignition switch is turned to position ‘II’. After
refuelling, the pointer rises to the new level after
the ignition switch is turned on. When the
ignition switch is turned off, the pointer quickly
lowers to the ‘empty’ position.
An arrow on the face of the fuel gauge indicates
the side of the vehicle on which the fuel filler is
situated.
WARNING
Never allow the vehicle to run out of fuel - the
resultant misfire could damage the catalytic
converter.
NOTE: Driving on twisting or hilly roads may
disturb the accuracy of the fuel gauge. It is
advisable to check the fuel level when the
vehicle is travelling on a straight, level road.
59
Page 64
WWW.MANUALS.WS
WWW.MANUALS.WS
Instruments
9. Low-fuel warning light
Illuminates when the fuel level is low
(approximately 2 gallons (9 litres) remaining).
If the light illuminates, refuel at the earliest
opportunity.
Illuminates as a bulb check when the ignition
switch is turned to position ‘II’ and extinguishes
when the engine is started.
Instrument illumination control
H5241
Rotate the control upwards to increase, or
down to decrease, the intensity of the
instrument panel illumination.
The illumination control also adjusts the
intensity of all switch illumination forward of
the driver.
60
Page 65
WWW.MANUALS.WS
WWW.MANUALS.WS
Warning Lights
Warning Lights
INSTRUMENT PANEL
H5107
The location and specification of the warning
lights may vary according to model and market
requirements.
Direction indicators - GREEN
The left or right warning light
flashes in time with the relevant
direction indicator when they are
operated. If either warning light fails to flash or
flashes rapidly, the selected direction indicator
light is not operating.
NOTE: If the hazard warning lights are
operated, both direction indicator warning
lights will flash together.
Headlight high beam - BLUE
Illuminates when the headlights are
switched to high beam.
Cruise control - AMBER
Illuminates when the cruise control
master switch is turned on and
cruise control is active, and
extinguishes when the switch is turned off or if
cruise control is deactivated.
Service engine soon - AMBER
Illuminates as a bulb check when
the ignition switch is turned to
position ‘II’ and extinguishes when
the engine is started. If the light illuminates
while the engine is running, this indicates the
detection of an emissions fault by the engine
management system.
If the light illuminates and the vehicle drives
normally:
• Arrange a service appointment at your
earliest convenience - you may still drive the
vehicle.
If the light flashes and/or the vehicle does not
drive normally:
• Avoid high speeds and seek qualified
assistance urgently.
Service engine - AMBER
the engine is started. If the light illuminates, this
indicates an engine service by a retailer is
required.
lluminates as a bulb check when
the ignition switch is turned to
position ‘II’ and extinguishes when
61
Page 66
WWW.MANUALS.WS
WWW.MANUALS.WS
Warning Lights
Parking brake & brake system - RED
The light illuminates when the
Parking brake is applied and
extinguishes when it is fully
released. If the light illuminates while the
Parking brake is released, a fault with the
braking system is indicated, check the brake
fluid level (see ‘BRAKE FLUID’, page 187). If the
light continues to illuminate, seek qualified
assistance urgently.
Door open - RED
Illuminates when any of the doors
(including the taildoor and bonnet)
are not fully closed. DO NOT drive
the vehicle with the light illuminated.
Traction control - AMBER
Illuminates as a bulb and system
check when the ignition switch is
turned to position ‘II’ and
extinguishes after approximately 4 seconds.
The light illuminates for a minimum of 2
seconds, whenever traction control is
operating.
If the light illuminates continuously while
traction control is NOT operating, a fault with
the system is indicated; seek qualified
assistance.
The light also has an overheat function: if
traction control is required, but the brakes are
too hot, the light will flash for the period when
traction control is required and traction has
been lost.
ABS - AMBER
Illuminates for approximately 1
second as a bulb and system check
when the ignition switch is turned
to position ‘II’, and then extinguishes. The light
may blink during this time.
If the light remains on or subsequently
illuminates while driving, a fault has been
detected by the self-monitoring system. This
means that full ABS control may not be
available and you should seek qualified
assistance urgently.
Hill descent control (HDC) ‘failure’ - AMBER
The light illuminates briefly as a
bulb check when the ignition switch
will flash if the brakes become in danger of
overheating and continue flashing until the
brakes have cooled sufficiently to enable HDC
to operate again (see also ‘HDC fade-out’, page 121).
If the light illuminates at any other time, a fault
in the system is indicated. If this occurs,
deselect HDC and consult your Land Rover
Retailer.
is turned to position ‘II’. The light
Hill descent control (HDC) ‘information’ GREEN
Illuminates briefly as a bulb check
when the ignition switch is turned
when HDC is selected.
If HDC is selected when either of the operating
gears is engaged (1st or reverse), the light will
illuminate continuously.
When HDC is selected and a non-operating gear
is engaged, the light will flash to inform the
driver that HDC is selected, but not operating
(see also ‘HDC fade-out’, page 121).
to position ‘II’ and will illuminate
62
Page 67
WWW.MANUALS.WS
WWW.MANUALS.WS
Warning Lights
Low oil pressure - RED
the engine is started. If the light remains on,
flashes on and off or illuminates continuously
when driving, serious engine damage could
occur; stop the vehicle as soon as safety
permits and SWITCH OFF THE ENGINE
IMMEDIATELY. Seek qualified assistance
before driving.
Seat belt - RED
ensure that the seat belts of all occupied seats
are securely fastened. The light extinguishes
after approximately five seconds, or when the
driver’s seat belt is fastened.
Airbag SRS - RED
seconds. If the light illuminates at any other
time, seek qualified assistance urgently.
Illuminates as a bulb check when
the ignition switch is turned to
position ‘II’ and extinguishes when
*
The light illuminates when the
ignition switch is turned to position
‘II’ as a reminder to the driver to
The light illuminates when the
ignition switch is turned to position
‘II’ and extinguishes after about five
When a trailer is not fitted, the warning light will
flash once each time the direction indicator
switch is operated.
NOTE: The trailer direction indicator light will
also flash when the hazard warning lights are
activated, whether a trailer is attached or not.
Battery charging - RED
The light illuminates as a bulb
check when the ignition switch is
turned to position ‘II’ and
extinguishes as soon as the engine is running.
If it remains on, or illuminates when driving, a
fault with the battery charging system is
indicated. Seek qualified assistance urgently.
Trailer direction indicators - GREEN
Illuminates in conjunction with the
vehicle direction indicator lights to
show that all trailer indicator lights
are functioning correctly. In the event of a bulb
failure on the trailer, the warning light flashes
once and then remains off.
63
Page 68
WWW.MANUALS.WS
WWW.MANUALS.WS
Audible Warnings
Audible Warnings
AUDIBLE WARNINGS
Lights on reminder
If the vehicle side, or headlights are left on after
the ignition switch is turned off, a warning
chime will sound when the drivers door is
opened. The chime will cease as soon as the
lights are switched off, or when the drivers door
is closed.
Ignition key reminder
If the key is left in the ignition switch while the
driver’s door is open, a warning will chime
continuously. The chime stops as soon as the
door is closed, or the key is removed from the
ignition switch.
64
Page 69
WWW.MANUALS.WS
WWW.MANUALS.WS
Lights & Indicators
Lights & Indicators
DIRECTION INDICATORS
LIGHTS
2
1
H5093
Move the lever DOWN to indicate a LEFT turn,
and UP to indicate a RIGHT turn (the
appropriate GREEN warning light on the
instrument panel will flash in time with the
direction indicators).
Hold the lever part-way up or down against
spring pressure to indicate a lane change.
H5094
The side, tail and headlights operate with the
ignition switch in any position.
If the exterior lights are left on after the ignition
switch is turned off, a warning chime will sound
as soon as the driver's door is opened. The
chime will cease as soon as the lights are
switched off, or the door is closed.
Side, tail and instrument panel lights
Turn lighting switch to position 1.
Headlights
Turn lighting switch to position 2.
65
Page 70
WWW.MANUALS.WS
WWW.MANUALS.WS
Lights & Indicators
Headlight high, and low beams
H5095
Pull the lever fully towards the steering wheel to
change headlight beams (BLUE warning light
glows when the headlights are on high beam).
To flash the headlights, pull the lever part way
towards the steering wheel and release.
66
Page 71
WWW.MANUALS.WS
WWW.MANUALS.WS
Lights & Indicators
FOG LIGHTS
WARNING
Fog lights should ONLY be used when
visibility is severely restricted - other road
users could be dazzled in clear conditions.
Rear fog guard lights
Press to operate, press a second
time to switch off (the red indicator
light in the switch illuminates when
the fog guard lights are switched on).
The rear fog guard lights operate ONLY when
the ignition switch is turned to position ‘II’ and
the headlights are switched on. Switching off
the headlights, or turning the ignition switch to
position ‘0’, will automatically extinguish the
rear fog guard lights.
DO remember to switch off as soon as visibility
is clear.
HAZARD WARNING LIGHTS
H5076
Front fog lights
illuminates when the fog lights are switched
on).
The front fog lights operate ONLY when the
ignition switch is at position ‘II’ and the side or
headlights are also switched on. The front fog
lights extinguish automatically when the side
lights or the ignition switch is turned off, but
will automatically be reselected when the
ignition switch is turned back on.
DO remember to switch off as soon as visibility
is clear.
*
Press to operate, press a second
time to switch off (the green
indicator light in the switch
H5074
Press to operate; all the direction
together. Use ONLY in an emergency to warn
other road users when your stationary vehicle
is causing an obstruction, or is in a hazardous
situation. Remember to switch off before
moving away.
67
indicator lights (including those
fitted to a trailer) will flash
Page 72
WWW.MANUALS.WS
WWW.MANUALS.WS
Wipers & Washers
Wipers & Washers
OPERATING
The wipers and washers will only operate when
the ignition switch is turned to position ‘I’ or ‘II’.
WINDSCREEN WIPERS
3
IMPORTANT
• DO NOT operate the wipers on a dry
screen.
• In freezing or very hot conditions,
ensure that the blades are not frozen or
stuck to the glass.
• In winter, remove any snow or ice from
around the arms and blades, including
the wiped area of the windscreen and
the heater air intakes.
NOTE: If the wiper blades have stuck to the
glass, a thermal cut-out may temporarily
prevent the wiper motor from operating. If this
is the case, switch the wipers off, free them
from the obstruction and then switch on again.
2
1
H5096
Intermittent wipe
Turn switch to position 1.
Normal speed wipe
Turn switch to position 2.
Fast speed wipe
Turn switch to position 3.
NOTE: If the front screen wipers are operating
(in either intermittent or continuous mode), the
rear wiper operates automatically whenever
reverse gear is selected.
68
Page 73
WWW.MANUALS.WS
WWW.MANUALS.WS
Wipers & Washers
Single wipe
WINDSCREEN WASHERS
H5099
H5097
Pull the lever toward the steering wheel. The
Pull the lever down and release immediately.
NOTE: With the lever held down, the wipers will
operate at high speed until the lever is released.
Variable delay (intermittent wipe)
windscreen wipers will operate in conjunction
with the washers for as long as the lever is held
in this position, the wipers continuing for a
further 3 to 4 wipes after the lever is released.
WARNING
If you operate your vehicle in temperatures
below 40
protection. Failure to do so, could result in
impaired windshield vision, possibly causing
a vehicle collision.
o
F, use washer fluid with anti-freeze
NOTE: State or local regulations may restrict
the use of Volatile Organic Compounds
(VOC’s), which are commonly used as
anti-freeze agents in washer fluid. A washer
fluid with limited VOC content should be used
only if it provides adequate freeze resistance for
H5098
Rotate the inner switch to vary the delay
between wipes.
all regions and climates in which the vehicle will
operate.
For more information on Wipers and Washers
see, ‘WINDSHIELD WASHERS’, page 190 and
‘Washer jets’, page 190.
69
Page 74
WWW.MANUALS.WS
WWW.MANUALS.WS
Wipers & Washers
REAR SCREEN WIPER AND WASHER
Rear window wash/wipe
Rear screen wiper
Press to operate: after
continuously wiping 3 or 4 times,
the wiper operates intermittently
(approx. once every 6 seconds) until switched
off.
NOTE: When reverse gear is selected, the rear
wiper will operate continuously in tandem with
the front wipers.
NOTE: Opening the taildoor, or lowering the
rear screen, will switch the rear wiper off.
H5078
Press and hold the switch for the
required duration of screen
washing. The wiper operates
automatically during washing and continues for
a further 4 wipes (approx.) after the switch is
released.
70
Page 75
WWW.MANUALS.WS
WWW.MANUALS.WS
Horn
Horn
HORN
H5080
To operate, press either of the horn switches
set into the steering wheel pad.
71
Page 76
WWW.MANUALS.WS
WWW.MANUALS.WS
Mirrors
Mirrors
EXTERIOR MIRRORS
NOTE: The mirror glass is convex, providing a
wider field of vision. As a result, objects
reflected in the mirror are closer than they
appear.
Adjustment
Folding the mirror body
The body of each door mirror is designed to
fold forwards or rearwards on impact. They can
also be folded back manually towards the side
windows into a ‘park’ position, to enable the
vehicle to negotiate narrow openings.
Manual operation: On some vehicles this
operation can be carried out manually, by
physically pushing the mirror bodies back
towards the side windows, and then pulling
them back into the normal (extended)
positions.
H5052
H5054
• Turn the control to the ‘L’ or ‘R’ position to
select either the left or right hand mirror.
• With the ignition switch turned to position
‘II’, push the control in the appropriate
direction to tilt the mirror glass up/down/left
or right.
• When adjustment is complete, return the
control to the OFF position (midway
between ‘L’ and ‘R’).
Heating elements
The exterior mirrors have integral heating
elements for dispersing ice and mist, which
operate automatically whenever the ignition
switch is in position ‘II’.
72
Page 77
WWW.MANUALS.WS
WWW.MANUALS.WS
Mirrors
Electric operation:*
On some vehicles, mirror folding can be carried
out electrically, as follows:
INTERIOR MIRROR
H5059
The interior mirror can be dipped to reduce
glare from following vehicles. In the event of
excessive glare, move the lever at the base of
the mirror forward to ‘dip’ the mirror. Normal
visibility is restored by pulling the lever back to
H5056
1. Ensure the mirror control is turned to the
centre position.
2. Push the control down once to fold the
mirrors back towards the side windows.
3. Before driving, push the control down a
second time to return the mirrors to their
normal driving position.
its original position.
NOTE: In some circumstances, the view
reflected in a ‘dipped’ mirror can confuse the
driver as to the precise position of following
vehicles. Remember to take additional care!
If one mirror is accidentally knocked out of
position, an additional operation of the switch
will re-synchronise them.
NOTE: After several consecutive operations of
the control, the mirror motor will cut-out. This
is not a fault and occurs automatically to
prevent the motor from overheating.
73
Page 78
WWW.MANUALS.WS
WWW.MANUALS.WS
Mirrors
VANITY MIRROR*
H5061
To use the vanity mirror, pull down the
passenger's sun visor. On some models, the
vanity mirror is illuminated; lift the mirror cover
to illuminate.
NOTE: Always close the cover, or on vanity
mirrors not fitted with a cover, always return
the visor to its stowed position when not in use,
to avoid possible scorching of the seats by the
sun reflected in the mirror.
74
Page 79
WWW.MANUALS.WS
WWW.MANUALS.WS
Windows
Windows
ELECTRIC WINDOW CONTROLS
5 DOOR VEHICLES
WARNING
Accidental closing of an electrically operated
window on fingers, hands or any vulnerable
part of the body, can result in serious injury.
Always observe the following precautions:
ISOLATE the rear window switches when
carrying children.
ENSURE that children are kept clear whilst
raising or lowering windows.
ENSURE that all adult passengers are familiar
with the controls and the potential dangers of
electrically operated windows.
DO NOT allow passengers to extend any part
of their bodies through a window aperture
while the vehicle is moving - injury from
flying debris, branches of trees, or other
obstructions could occur.
It is recommended that the ignition key be
removed when leaving the vehicle.
1
3
H5038
The switches on the driver’s door console
operate the windows as follows:
1. Left hand front window.
2. Right hand front window.
3. Left hand rear window.
4. Right hand rear window
5. Isolation switch for rear door window
switches.
5
2
4
NOTE: Electric rear windows can also be
operated by the individual switches mounted on
each rear door, provided that the isolation
switch has not been activated.
75
Page 80
WWW.MANUALS.WS
WWW.MANUALS.WS
Windows
Operating the windows
The electric windows can be operated when the
ignition switch is at position ‘II’ and for up to 45
seconds after the ignition switch is turned off
(provided neither front door is opened in the
meantime).
Press and hold the bottom half of a switch to
lower and the upper half to raise. The window
will stop moving when the switch is released.
NOTE: ENSURE that all adult passengers are
familiar with the controls and the potential
dangers of electrically operated windows.
Rear window isolation switch
Front door - passenger’s window switch
The front seat passenger can also
independently control the raising and lowering
of their window by using the switch on the
passenger door. Press and hold the bottom half
of the switch to lower and the upper half to
raise. The window will stop moving when the
switch is released.
Rear door - passenger’s window switch
H5040
Rear seat passengers can control the raising
and lowering of their window by using the
switch on either of the rear doors. (Provided
H5041
Press switch ‘5’ as indicated to isolate the rear
window switches. Press the other end of the
switch to restore independent control.
‘One touch’ down (Driver's door only)
By pressing (and then releasing) the bottom
half of switch ‘1’ (AUTO) to the second detent
position, the window will open fully at a single
touch. Window movement can be stopped at
any time by briefly pressing the upper half of
the switch.
that the rear windows have not been isolated by
the driver).
Press and hold the bottom half of a switch to
lower and the upper half to raise. The window
will stop moving when the switch is released.
NOTE: ENSURE that all adult passengers are
familiar with the controls and the potential
dangers of electrically operated windows.
76
Page 81
WWW.MANUALS.WS
WWW.MANUALS.WS
Windows
3 DOOR VEHICLES
‘One touch’ down (Driver's door only)
By briefly pressing (and then releasing) the
bottom half of the driver’s window switch, the
window will open fully at a single touch.
Window movement can be stopped at any time
by briefly pressing the upper half of the switch.
H5239
The switches on centre console operate the
windows as follows:
Operating the windows
The electric windows can be operated when the
ignition switch is at position ‘II’ and for up to 45
seconds after the ignition switch is turned off
(provided neither door is opened in the
meantime).
Press and hold the bottom half of a switch to
lower and the upper half to raise. The window
will stop moving when the switch is released.
NOTE: ENSURE that all adult passengers are
familiar with the controls and the potential
dangers of electrically operated windows.
77
Page 82
WWW.MANUALS.WS
WWW.MANUALS.WS
Windows
ELECTRIC TAILDOOR GLASS
WARNING
Long loads should be carried on the roof rack.
If it is necessary to carry a load that protrudes
through the taildoor window, the weight of the
load must NOT rest on the glass of a partially
open window. Damage to the glass or window
mechanism may occur (see also
‘Accommodating long loads’, page 44).
NOTE: The taildoor glass can be lowered from
outside the vehicle, to enable easy access to the
loadspace area when it is impossible or
inconvenient to open the taildoor.
Raising and lowering
Press the upper half of the switch to raise the
glass. If the switch is released before the glass
is fully raised, it will automatically lower again.
NOTE: On 3-door models, the taildoor glass
cannot be raised if the soft-back is
raised/removed or if the hard-back is removed.
One touch down:
By briefly pressing (and then releasing) the
bottom half of the switch, the taildoor glass will
open fully at a single touch.
H5045
From outside the vehicle:
Press and hold the UNLOCK button on the
remote handset (hold for 2 seconds) - the
taildoor glass will fully lower.
To raise the glass, insert the ignition key into
the switch mounted in the taildoor handle and
turn clockwise. If the switch is released before
the glass is fully raised, it will automatically
H5043
From inside the vehicle:
With the ignition switch in position ‘II’, press
and hold the bottom half of the switch to lower
the glass, movement will stop when the switch
is released.
lower again.
NOTE: If the vehicle is locked when the glass is
lowered using the handset, the driver's door
will unlock and the security features will be
disarmed.
Remember to relock the vehicle (if required).
78
Page 83
WWW.MANUALS.WS
WWW.MANUALS.WS
Windows
H
Battery disconnection
If the battery has been disconnected, the
taildoor glass will need to be recalibrated. If the
alarm was armed when the battery was
disconnected (or discharged), disarm the
alarm after reconnection - the glass will fully
lower. This will happen automatically if the
alarm was in a disarmed state when the battery
was disconnected.
After battery reconnection, fully raise the glass
- the taildoor glass is now recalibrated (if the
glass is not fully raised, an error ‘beep’ will
sound).
REAR VENTILATOR WINDOWS
(3-door models)
2354A
To open, pull the catch forwards and push
outwards until the window ‘clicks’ into position.
To close, pull the centre of the catch inwards,
then push rearwards until the catch is felt to
‘clip’ into the locked position.
NOTE: Ensure that children are kept clear while
operating the windows.
79
Page 84
WWW.MANUALS.WS
WWW.MANUALS.WS
Sunroof
Sunroof
ELECTRIC SUNROOF*
H5146
The sunroof can be operated when the ignition
switch is turned to position ‘II’ and for up to 45
seconds after the ignition switch is turned off
(provided neither front door is opened in the
meantime).
The roof opens in two separate phases as
follows:
• To tilt the roof: Press the bottom half of the
switch - the rear edge of the roof rises to the
tilted position.
• To open the roof: With the sunroof fully
tilted, press the bottom half of the switch the roof remains tilted and slides towards
the rear until fully open or the switch is
released.
NOTE: Do not operate the sunroof when it is
obstructed, or covered in ice or snow - damage
could be caused.
To close the roof: press the upper half of the
switch - the sunroof will first close to the tilted
position, then it will return the tilted roof to the
closed position. The sunroof can be stopped (at
any position) by releasing the switch.
Accidental closure of a sunroof on fingers,
hands or any vulnerable part of the body, can
result in serious personal injury. Always
observe the following precautions:
ENSURE that children are kept clear and that
the sunroof is not obstructed when opening or
closing.
DO NOT allow passengers to extend any part
of their bodies through the sunroof aperture
while the vehicle is moving - injury from
flying debris, branches of trees or other
obstructions could occur.
Do not open the sunroof if the load on the roof
rack will impede its operation.
ALWAYS close the roof when the vehicle is
unattended.
NOTE: Ensure that all adult passengers are
familiar with the controls and the potential
dangers of operating an electrically operated
sunroof.
Sunroof visor
The sunroof visor needs to be opened and
closed manually.
Driving with the sunroof open
If, when driving with the sunroof open,
unwanted drafts are experienced, open the
front fascia air vents, and increase the blower
speed if necessary.
NOTE: Operating the air conditioning with the
sunroof open is NOT recommended.
WARNING
80
Page 85
WWW.MANUALS.WS
WWW.MANUALS.WS
Sunroof
Sunroof blind
H5148
Pull the sunroof blind across the sunroof
aperture to open and close.
81
Page 86
WWW.MANUALS.WS
WWW.MANUALS.WS
Targa Roof
H
H3314
Targa Roof
TARGA ROOF
3313
The targa roof is made up of twin glass panels
set into the roof. Either, or both panels, can be
tilted open or removed completely.
Tilting a panel (see left inset)
1. Pull the handle forward to unlock.
2. Push the handle up.
3. Push the handle to the rear until it ‘clicks’
into the lock position.
To close the panel, reverse the above
procedure.
Note: Handle glass with care, avoid damage to
the surfaces, especially along the edges.
WARNING
DO NOT allow passengers to extend any part
of their bodies through roof apertures whilst
the vehicle is in motion. Injuries from flying
debris, branches of trees or other
obstructions could occur.
Storing the panels
Removing a panel
WARNING
DO NOT attempt to remove the targa roof
panels whilst the vehicle is moving.
Half tilt the panel (as in 1 and 2 above), then
press the red catch to detach the handle
linkage. From outside the vehicle, raise the rear
of the panel until the two front hinges
disengage and lift the panel off.
After removal, always protect the panels by
placing them in the stowage case attached to
the rear seats as shown above.
WARNING
DO NOT drive with the roof panels loose in the
vehicle, they may become dangerous
projectiles in the event of an accident or
emergency manoeuvre.
82
Page 87
WWW.MANUALS.WS
WWW.MANUALS.WS
Targa Roof
H
H3316
Refitting a panel
Removing the ‘T-bar’
3315
NOTE: The left and right roof panels are NOT
interchangeable. To ensure accurate refitting,
the rounded corner of each panel should be
positioned at the front outside corner.
To refit the panels -
1. From above, feed the hinges through the
slots in the wind deflector, and into the
slots in the front edge of the roof aperture
(as shown above).
2. Lower the roof panel whilst ensuring that
the handle linkage is the correct way up,
and push the handle rearwards (as if
locking).
3. The handle should now be engaged -
ensure that the red button is fully
retracted, then open the roof to the tilt
position to check.
NOTE: ALWAYS close and secure the roof when
leaving the vehicle unattended.
With both panels removed the ‘T-bar’ can also
be removed.
• Press the RED catches rearwards (as
arrowed in the top inset above), then pull the
bar upwards and then forwards to remove.
• After removal place the ‘T-bar’ into the
pocket provided in the stowage case
attached to the rear seats.
WARNING
DO NOT drive with the ‘T-bar’ loose in the
vehicle, it may become dangerous projectiles
In the event of an accident or emergency
manoeuvre.
When replacing, ensure that the ‘T-bar’ is
secured at the rear, then press downward to
engage the front (RED) locking catches.
83
Page 88
WWW.MANUALS.WS
WWW.MANUALS.WS
Heating & Ventilation
Heating & Ventilation
VENTILATION
H5213
The ventilation system provides fresh or heated
air to the interior of the vehicle from the air
intake grille in front of the windscreen.
NOTE: Always keep the air intake grille clear of
obstructions such as leaves, snow or ice.
Air outlets are provided to the windscreen, face
and feet - the location of the vents is shown in
the illustration above. The temperature of the
air is controlled by the heater.
Information concerning the operation of the
heating and ventilation system, as well as the
air conditioning, appears on the pages that
follow.
Particle filter
Particle filters help to keep the vehicle interior
free from pollen and dust. To remain fully
effective, the filter should be replaced at least
every 12 months or 12,000 miles (20,000 km),
at the time of a main service.
84
Page 89
WWW.MANUALS.WS
WWW.MANUALS.WS
Heating & Ventilation
HEATER CONTROLS
456
3
2
7
8
1
H5063
1 & 9. Heated front seats*
With the ignition switch turned on and the
engine running, press the switches to operate
the heating elements in either the driver's or
front passenger seat (the indicator light in the
switch illuminates). Press a second time to
switch off.
NOTE: The seat heaters will switch off
automatically 45 seconds after the ignition
switch is turned off, or either front door is
opened.
The seat heaters are thermostatically controlled
and operate intermittently to achieve and then
maintain a predetermined temperature
between79
NOTE: Owners should be aware that the seat
heaters consume considerable power from the
battery and for this reason, it is recommended
that they are operated only with the engine
running.
o
F and 97oF (26oC and 36oC).
2. Heated rear window
Press to operate; press a second time to switch
off. The indicator light in the switch illuminates
whenever the heater is on and extinguishes
when the heater is turned off.
NOTE: The heated rear window will operate only
with the taildoor fully closed and when the
engine is running and will switch off
automatically after approximately 15 minutes.
WARNING
DO NOT stick labels over the heating
elements, and DO NOT scrape or use abrasive
materials to clean the inside of the window.
3. Heated windsheild*
Press to operate; press a second time to switch
off. The indicator light in the switch illuminates
whenever the heater is on and extinguishes
when the heater is turned off.
NOTE: The front screen heater will operate only
when the engine is running and will switch off
automatically after approximately 10 minutes.
9
85
Page 90
WWW.MANUALS.WS
WWW.MANUALS.WS
Heating & Ventilation
4. Air distribution control
Rotate to select air distribution:
Air to face vents
(to ensure best performance, the face
level vents must be fully open)
Air to face vents and foot outlets
(to ensure best performance, the face
level vents must be fully open)
Air to foot outlets
Air to foot outlets and windscreen
(if the ambient temperature is
approximately 41
air conditioning (if fitted) will automatically
dehumidify the air to reduce misting).
All air to windscreen
(if the ambient temperature is
approximately 41
air conditioning (if fitted) will automatically
dehumidify the air to reduce misting).
5. Air blower control
Turn the control clockwise to progressively
increase the blower speed.
NOTE: With the control in position ‘O’, the
volume of air entering the vehicle is dependent
on driving speed alone.
o
F (5oC) or higher, the
o
F (5oC) or higher, the
6. Air temperature control
Rotate the control clockwise (towards the RED
segments) to increase the air temperature, or
anti-clockwise (towards the BLUE) to reduce
the temperature.
7. Air conditioning button
With the engine running, press to operate. The
indicator light in the switch illuminates when
the air conditioning is switched on.
8. Air recirculation button
Press to recirculate air inside the vehicle
(indicator light illuminates).
The air recirculation mode prevents the heating
system from taking in fresh air from outside the
vehicle. Instead, the air already inside the
vehicle is recirculated, thus preventing the
entry of traffic fumes. In cold weather air
recirculation also enables warmer air to be used
to defrost the windscreen when the engine is
still cold.
WARNING
The air recirculation mode can cause the
windscreen to mist. If this happens, switch off
air recirculation immediately.
86
Page 91
WWW.MANUALS.WS
WWW.MANUALS.WS
Heating & Ventilation
USING YOUR HEATER
Fresh air enters the heater unit through the
grille in front of the windscreen and stale air is
drawn out through vents in the rear of the
vehicle. Ducts beneath the front seats provide
heating for rear seat passengers - these must
not be obstructed.
The following examples of basic heater settings
are intended as a general guide; the air
distribution, temperature and blower controls
can then be further adjusted to suit your
comfort requirements.
Always remember that full heating is not
available until the engine has reached its
normal operating temperature.
Maximum heating
Demisting
H5066
Set the controls as shown, to obtain the
maximum flow of heated air from the
windscreen and side window vents. Selection
of air conditioning will also assist in demisting.
On vehicles NOT equipped with air
conditioning, opening a window may improve
ventilation.
Defrosting
H5065
Set the controls as shown, with the blower at
the slowest speed (position 1) until the
temperature gauge indicates that the engine is
warming up - the blower speed can then be
increased.
H5067
Set the controls as shown and switch on air
recirculation to prevent cold air from being
drawn into the vehicle. Turn air recirculation off
as soon as the windscreen is clear, to prevent
any possibility of the windscreen misting.
87
Page 92
WWW.MANUALS.WS
WWW.MANUALS.WS
Heating & Ventilation
H
Maximum ventilation
FACE LEVEL VENTS
H5069
Set the controls as shown, with the face level
vents open. Adjust the blower speed as
required.
2329A
Rotate the thumbwheel down to open or up to
close the vents. Direct the air flow by moving
the control in the centre of the louvres up or
down, or from side to side.
To increase output from the centre face vents,
shut the outer vents.
When carrying rear seat passengers, use the
outer vents for the front seat occupants and use
the more powerful centre vents for the rear seat
passengers.
On 3-door models, when driving with either the
hard or softback removed (or folded in the case
of the softback), open all the vents and turn the
blower switch on - this will help prevent the
ingress of poisonous exhaust fumes.
NOTE: On both 3 and 5-door models, driving
with the taildoor or taildoor window open is not
recommended because poisonous exhaust
fumes will be drawn into the vehicle. (See
‘Accommodating long loads’, page 44).
88
Page 93
WWW.MANUALS.WS
WWW.MANUALS.WS
Heating & Ventilation
AIR CONDITIONING
The air conditioner provides additional cooling
and also reduces humidity. This can be used to
demist windows quickly in damp weather and,
when used in conjunction with the heater,
makes the interior of the vehicle warm and dry.
NOTE: In high humidity conditions, slight
screen misting may be experienced when the
air conditioning is turned on. This is a natural
occurrence for most automotive air
conditioning systems; it is not a fault with the
system and will clear after a few seconds, once
the air conditioning is operating.
Using the air conditioning
The air conditioning can only be used when the
engine is running and with the blower switched
on. For the air conditioning system to operate
efficiently, all windows (and the sunroof/Targa
roof) should be closed, and the air intake vents
free from ice, snow, leaves and other debris.
Operating of the air conditioning with the
softback opened, or the hardback removed is
not recommended.
With the engine running, press the ‘A/C’ button
and adjust the air distribution, blower and air
temperature controls as required.
NOTE: The air conditioner will automatically
operate when the air distribution control is set
to ‘All air to windscreen’ or ‘Air to foot outlets
and windscreen’, see ‘4. Air distribution
control’, page 86.
Operation of the air conditioning system places
an extra load on the engine. In very hot
conditions or when the engine is required to
work unusually hard (climbing long hills or
driving in congested traffic, for example), this
could result in high engine temperatures. If the
pointer nears the RED zone of the temperature
gauge, temporarily turn the air conditioning off
until engine temperatures return to normal.
NOTE: Under extreme conditions, the air
conditioning may automatically switch off, to
prevent damage to the engine.
Rapid cooling:
With the engine running press the ‘A/C’ button,
turn the air temperature control to the BLUE
segment, select air recirculation and turn the
blower switch to ‘4’. Turn the air distribution
control to the face vent setting and fully open all
four face level vents. Turn off air recirculation
and adjust the blower when the vehicle interior
is cool.
NOTE: In very hot conditions, it may be
advisable to fully ventilate the vehicle by
opening the windows and sunroof for a while
before closing them again and operating the air
conditioning.
Maintaining the air conditioning
The air conditioning system is sealed and major
maintenance should only be carried out by a
qualified technician. To maintain the system in
peak condition, owners should ensure that the
system is operated for a short period every
week (even during the cold winter months);
with the engine at its normal operating
temperature, run the air conditioning for at least
ten minutes whilst driving at a steady speed.
Surplus water produced by the dehumidifying
process is expelled from the system via drain
tubes beneath the vehicle. This may result in a
small pool of water forming on the road when
the vehicle is stationary and is not a cause for
concern.
89
Page 94
WWW.MANUALS.WS
WWW.MANUALS.WS
Interior Equipment
H
H
H
Interior Equipment
COURTESY & MAP READING LIGHTS
(5-door models)
COURTESY LIGHT (3-door models)
2352A
Front courtesy and map reading lights
2593
Rear courtesy light
Press the appropriate switch to illuminate (or
extinguish) the lights manually.
The front and rear lights illuminate
automatically when the vehicle is unlocked or
whenever a door or taildoor is opened, and
extinguish approximately 15 seconds after ALL
the doors are closed, or as soon as the ignition
switch is turned on.
If a door or the taildoor remains open for ten
minutes or more, a ‘time out’ function will
extinguish the courtesy lights in order to
prevent the battery from discharging.
NOTE: If the map reading lights or rear courtesy
light are left on after being manually selected,
they will NOT extinguish automatically.
3322
Switch positions:
• ‘OFF’ - Light permanently off.
• ‘ON’ - Light illuminates continuously.
With the switch in the centre position, the
interior light illuminates automatically
whenever the vehicle is unlocked or when a
door or taildoor is opened. The light remains
illuminated for 15 seconds after the doors and
taildoor are closed, or until the ignition switch
is turned on.
If a door or the taildoor remains open for ten
minutes or more, a ‘time out’ function will
extinguish the courtesy lights in order to
prevent the battery from discharging.
NOTE: If the courtesy light is left on after being
manually selected, it will NOT extinguish
automatically.
The courtesy lights will extinguish when the
vehicle is locked.
LUGGAGE COMPARTMENT LIGHT
Illuminates automatically when the taildoor is
opened.
The courtesy lights will extinguish when the
vehicle is locked.
90
Page 95
WWW.MANUALS.WS
WWW.MANUALS.WS
Interior Equipment
CLOCK
GLOVEBOX
WARNING
DO NOT drive with the glovebox open. An
open glovebox could cause injury to the front
seat passenger in the event of a collision.
H5087
The digital clock display illuminates when the
ignition switch is turned on and dims for night
viewing when the sidelights are switched on.
With the ignition switch turned to position ‘I’,
press the hour (‘H’) and minute (‘M’) buttons to
set the time. If both buttons are pressed
together, the display will change between 24
hour and 12 hour displays.
NOTE: If the battery is disconnected, the clock
will need to be reset.
H5159
Lift the handle to open the glovebox - the two
recesses in the glovebox lid can be used, when
the vehicle is stationary, as cup stands.
The left hand compartment in the glovebox can
be used to store CD cases.
Glovebox light
Operates automatically when the exterior lights
are switched on and the passenger glovebox is
opened.
91
Page 96
WWW.MANUALS.WS
WWW.MANUALS.WS
Interior Equipment
H
DRIVER'S STORAGE AREA
DRINKS STOWAGE
WARNING
DO NOT drive with the storage area open. The
storage area lid could cause serious injury in
the event of a collision.
3325A
The expanding strap fitted to the front door
stowage compartment on 5-door models can
be used to store drink containers securely when
driving.
NOTE: Drink containers over 0.5 litre capacity
will not be properly secured by the strap.
H5161
Do not use the strap to store hot drinks.
WARNING
Lift the handle to open the driver's storage area
- when the vehicle is stationary, the two
recesses in the lid can be used as cup stands.
The right hand compartment in the storage area
can be used to store tape and CD cases.
92
Page 97
WWW.MANUALS.WS
WWW.MANUALS.WS
Interior Equipment
CUP HOLDERS*
Front cup holders
WARNING
The driver should not drink and should not use
the cup holder whilst driving.
If the cup holder is retractable, it should be
kept closed when not in use.
DO NOT place anything other than suitable
drinks containers in the cup holders, because
such items may be thrown about in the
passenger compartment and possibly injure
occupants in the event of an accident or
emergency manoeuvre.
Do not carry open-top drink containers in the
cup holders while the vehicle is in motion; a
spilled hot drink could cause personal injury.
Spilled drinks can also damage upholstery,
carpeting and electrical components.
Use only for soft containers. DO NOT use to
hold cups made of glass, china or hard
plastic, as these may caus e injury in the event
of an accident or emergency manoeuvre.
Unopened, sealed containers (drinks cans,
for example) are hard objects and may also
cause injury.
H5133
The front cup holders are located on the top
surface of the fascia panel, as illustrated above.
Rear cup holders
*
93
H2550
With the centre armrest lowered, press the
front of the cup holder to open. The retaining
arms can be adjusted to suit a range of
container sizes. Press the front of the cup
holder again to close.
Page 98
WWW.MANUALS.WS
WWW.MANUALS.WS
Interior Equipment
H
H
SUN VISOR
SUNGLASSES POCKET (3-door models)
3326
2424
To shield your eyes from the sun, pull the visor
down from the roof; the visor can be used to
shield the upper part of the windscreen or the
side window as required.
NOTE: On some models, the sun visors are
fitted with a vanity mirror on the underside.
On 3-door models, there is a pocket designed to
be a convenient place to stow sunglasses.
NOTE: Keep sunglasses in a soft case, to
prevent scratching.
WARNING
Do not store loose items (tapes, coins etc.) in
the sunglasses pocket these could become
dangerous projectiles in the event of a sudden
stop or collision.
94
Page 99
WWW.MANUALS.WS
WWW.MANUALS.WS
Interior Equipment
ASHTRAY
CIGAR LIGHTER
WARNING
DO NOT use the ashtray for disposing of waste
paper or other combustible items.
H5200
Front ashtray illustrated
Push the front to open the ashtrays. To remove
for emptying; with the ashtray open, carefully
pivot the ashtray upwards and withdraw it from
the aperture.
To refit the ashtray, partially insert the tray into
the aperture, then pivot downwards before
pushing the ashtray closed.
H5201
With the ignition switch turned on, press the
lighter in to heat up. When it has reached the
correct temperature it will partially eject and
can then be withdrawn for use.
• ONLY hold the cigar lighter by the handle.
DO NOT plug accessories into the cigar lighter
socket, unless they are approved for that
purpose by Land Rover, as potential damage
could occur to the vehicle’s electrical
systems.
ALWAYS ensure that driving controls are not
inhibited by any accessories plugged into the
cigar lighter socket.
WARNING
95
Page 100
WWW.MANUALS.WS
WWW.MANUALS.WS
Rear Door
Rear Door
REAR DOOR
H5158
WARNING
Lights located on the same side of the vehicle
as the rear door hinges will be obscured when
the door is fully open.
NOTE: Owner should be mindful of and
considerate to local traffic/environmental
conditions.
96
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.