Landoll ICON 1205 User Manual

CARRY ALL 1205

Parts & Service Manual

Index

Specifications

Product Warranty

Safety Section

Hook Up And Operation

Parts Listing

Parts And Bolt Location

Bolt Listing

Hydraulics

Decal Listing

Torque Specs

Specifications Of 1205 Carry All

Maximum Horsepower…………………………………...140

Weight…………………………………………………….6,450 lbs

Overall Length…………………………………………….202 in.

Overall Height…………………………………………….. 78 in.

Overall Width……………………………………………...154 in.

Cutting Width……………………………………………...144 in.

Cutting Edges………………………………………………(2) 6 ft. CAT

Number Of Tires…………………………………………...4

Tire Size…………………………………………………….12.5 x 15 - 10 ply

Rim Size…………………………………………………….10 x 15

Hitch………………………………………………………...Pintel w/68,800 lb rating

Hydraulics…………………………………………………...4000 psi hoses

Cyls………………………………………………………….4 x 16 (clam)

4 1/2 x 16
4 x 16 ( lift/tilt)

Bit to Ground Clearance
(fully raised position)………………………………………..18”

Heaped Capacity……………………………………………….5.5 yds

Struck Capacity………………………………………………...4.25 yds.

Literature Information

This information should be stored in the
literature holder located on the machine.
This manual contains safety information,
operating instructions, lubrication and
maintenance information.
Some of the photographs or illustrations in the
publication show details that can differ slightly
from your personal machine. Shields and covers
may have been removed to allow for
illustrations.
Constant improvement and knowledge of
product design may cause changes to your
personal machine that is not listed in this manual.
Read, understand, and keep this manual with the
machine to aid in repairs, adjustment, service and
parts identification.
Whenever a question arises regarding your
machine, or this manual, please contact Product
Support for assistance.

Maintenance

The maintenance section is a guide to
machine care. The illustrated step by step
procedures covers the most important of the
maintenance schedule. Regular routine
lubrication is described in less detail.

Maintenance Intervals

Normally, all lubrication should be on a
daily basis. However, certain locations only
require lubrication on a weekly basis or
require a specific quantity. These locations
will be marked clearly, showing and
describing requirements.

Under extremely severe, dusty/wet/sandy
conditions, or if the haul is long and rough,
more frequent lubrication and inspection of
highly stressed areas is recommended.

Safety
The safety section of this manual lists basic

safety precautions. In addition, this section
shows the location of safety signs and decals
used on this machine.
Read and understand the basic precautions
listed in the safety section before operating or
performing lubrication, maintenance or repair
work on this machine.

NOTE: Before any service or repair work is
performed, make certain that all safety stops
are in place.
Be certain to remove all safety stops when
repairs are complete.

Operation

This operation section is a reference guide for
the new operator and a refresher for the
experienced operator. Operating techniques
shown are basic, skill and technique will increase
with knowledge and usage of the machine.

Section 01
Safety

High pressure fluid can cause serious damage to
hands and eyes.

Carefully relieve pressure before attempting any
adjustments.

Tighten all fittings before applying pressure.

If fluid is sprayed into eyes or injected into skin
See a Doctor Immediately !

Horsepower Limits

Each machine is rated for it’s horsepower
limits.

If the posted limits are exceeded, damage
to the machine may occur, and the
Warranty will void.

NOTE: 300 maximum engine h.p. is only
applicable if the grader is equipped
with the 2nd cylinder.

Section 02
Hookup and Operation

The utilizes three hydraulic valves on the tractor, allowing it to function in
three different directions. The Carry All has the ability to raise to a clearance from bit to ground of 18 inches
while lowering to a negative cut. It can tilt from corner to corner approximately 15 degrees to accomplish
slope cuts and ditching. The third action is the clam function. All three of these functions can be done on the
go, or while the unit is stopped.
Color coded tie straps and markers are attached at the tip end of the hoses to identify the 6 hydraulic lines
on the machine. Black tie is the raise and lower of the blade. White tie is the clam function. Yellow is the tilt
of the bowl. The Carry All uses 5 hoses, with a Tee installed in the body tilt line. This allows one cylinder to
control the function.

NOTE: The tilt function is more responsive and easier to set, if the machine is lowered to
approximately 1/2 way. This allows both cylinders to have some free travel to adjust.

Hookup of the hydraulic hoses to the remote can be done in any way to suit individual needs. The following

method is suggested: Raise/Lower of the blade to #1 valve. Clam function to #2, and bowl tilt to #3. Hook up
so push of the valve is lower and pull of the valve is to raise the blade.

WARNING! Before Use, be certain that the cylinder stops are removed .

Be patient for the first few hours of learning to operate the unit. Time and experience will produce expert

results. Any type of blade machine has the tendency to create a “washboard” effect if grading is done with
too much speed. Slow down and do the job right. The second tendency of any blade machine is to side draft
if the blade is cutting deep and enough power is applied. Practice centering the cut on the blade to balance
the draft. Operating at a higher speed may not get the job done quicker, and may provide less than quality
results.
This model is designed to be pulled with a maximum of 140hp . Additional horsepower will shorten the
life of the machine and will alter the Warranty. Responsible operation and proper maintenance will provide
many hours of expert results and a durable machine.

Caution
This machine is not intended for highway use, it should be used off road only.
If public roadway travel is necessary, be certain of regulations concerning width,
lighting, and safety chain requirements.

The tongue assembly is bolted on, and is removable for ease of transportation.
It uses (16) 7/8 x 2 1/2” hex bolts, hard flat washers and hex nuts, and the top (6) are 7/8 x 3 1/2” to
allow for the extra plate of the bolt on top cylinder support.

Carry All 1205

4000371 4 1/2 x 16

SCR2065
Axle support pin

4000135 Manifold block
(2) 4000136 Hyd Check

1/2” x 3”
nylock nut

Axle supports are SCR2062L & R

4000100 4 x 16

Depth Gauge
SCR2072

1/2” x 4”
washer, &
nylock nut

GRA1600 Cylinder Pin

Hubs are GRA1966 (4),
they are 8 bolt, rated at
6500 lbs.

Tires are 4000086,

12.5 x 15, ten ply. mounted
on 4000005 10 x 15 rims
Should be inflated to 35psi

Axle Supports are
ICO02062L & R

The hubs are bolted to the
axle supports, using
3/4 x 6 1/2” gr. 8 bolts.