Lancom OAP-1702B, OAP-1700B User Manual

5

6

LANCOM OAP-1700B



LANCOM OAP-1702B

Quick Reference Guide

Cloud-ready

Mounting

b ca

Screw the connector ange b to the back of the housing with the
four screws and their washers.

When fastening the clamp prole c, please pay attention
to tighten the screws equally with a maximum torque of
7 Nm!

Wall mounting

Use the mounting arm a as a
template. Fix the mounting arm
to the wall with the supplied
screws and dowling plugs.

Attach the access point with
the connector ange b to the
mounting arm a. Use the
M8 x 110 bolt with spring locking
washer, washer and nut.

The main beam direction of the integrated antenna can be adjusted
by tilting the access point up or down by rotating the connection

ange about the mounting arm.

Pole mounting

Place the clamp prole c
around the pole. Screw

the clamp prole onto the

mounting arm with the
supplied screws.

k l k k k k

WLAN1 Ant2 WLAN1 Ant3

d

ETH1 (PoE)

e e

Wi-Fi antenna interfaces (only OAP-1702B)

d

For the WLAN1 module, screw the supplied WLAN antennas to the connectors WLAN1 Ant1 and WLAN1 Ant2. The antenna ports
for WLAN2 are located on the back of the device.

ETH1 (PoE), ETH2 interfaces

e

The ETH1 (PoE) connector also supplies power to the device. Plug in the water-proof power cable to the ETH1 ( PoE) port and care­fully tighten the threaded connector. Connect the other end of the network cable to the ‚Power Out‘ connector j of the supplied
PoE injector. Connect the interface ETH 2 with a sealed Ethernet cable to your PC or a LAN switch.

Reset button (part of the LED block)

f

To restore the device to its default conguration, keep the reset button on the device pressed until the LEDs on the device go out.
The following automatic restart restores the default conguration to the device.

Grounding

g

Screw one end of the green/yellow grounding wire to the housing and attach the other end to a suitable ground.

PoE injector - h LAN-In / j Power-Out / i Power supply interfaces

h

Using Ethernet cables, connect the ‚LAN-In‘ interface h of the provided PoE injector to a free socket of your local network and
the ‚Power-Out‘ interface j to the ETH1 (PoE) interface of the access point.

i

Supply power to the PoE injector i. Only use the supplied PoE Injector to supply power to this device. Particularly, do not connect

j

the PoE Injector to non-PoE Ethernet devices!

Wi-Fi antenna interfaces at the rear side (only OAP-1702B)

k

The following Wi-Fi antenna interfaces are located at the rear side of the device: WLAN1 - Ant1, WLAN2 - Ant1-4

BLE antenna interface at the rear side (only OAP-1702B)

l

Attach the provided BLE antenna to the BLE interface.

ETH2

f

PWR
ETH1 WLAN1

Reset

ETH2 WLAN2

d

g

WLAN1 Ant2 WLAN1 Ant3

ETH1 (PoE)

a PWR

Off Device switched off

Green, permanently* Device operational,

Green, blinking Conguration password not set. Without a

1x green inverse
blinking*

2x green inverse
blinking*

3x green inverse
blinking*

resp. device paired / claimed and LANCOM
Management Cloud (LMC) accessible

conguration password, the conguration

data in the device is unprotected.

Connection to the LMC active, pairing OK,
device not claimed

Pairing error, resp.
LMC activation code not available

LMC not accessible, resp.
communication error

ETH2

PWR

a

ETH1 WLAN1

b

Reset

ETH2 WLAN2

c

b ETH1 / ETH2

Off No networking device attached

Green,
permanently

Green, ickering Data trafc

Connection to network device operational,

no data trafc

c WLAN1 / WLAN2

Off No Wi-Fi network dened or Wi-Fi module

Green At least one Wi-Fi network is dened and

Green, ashing

inverse

Green, blinking DFS scanning or other scan procedure

deactivated. The Wi-Fi module is not trans­mitting beacons.

Wi-Fi module activated. The Wi-Fi module is
transmitting beacons.

Number of ashes = number of connected

Wi-Fi stations and P2P wireless connections,
followed by a pause (default).

Alternatively the frequency of the ashing
can indicate signal strength over the dened

P2P link or the signal strength between the
access point and the device operating in
client mode.

Hardware

Power supply Via Power-over-Ethernet compliant to IEEE 802.3at

Power consumption PoE: 15.1 W (measured at the PoE injector)

Environment -33 °C to +70 °C

Housing Robust metal housing, protection class IP 67, for wall and pole mounting.

Wi-Fi

Frequency bands 2.4 GHz or 5 GHz, 2400-2483.5 MHz (ISM) or 5150-5825 MHz

Antenna gain
(only OAP-1700B)

Minimum transmission
power

Radio channels 2.4
GHz

Radio channels 5 GHz Up to 26 non-overlapping channels (channels available vary according to country regulations;

Bluetooth Low Energy iBeacon: The device can broadcast a congurable iBeacon.

Interfaces

ETH1 (PoE) 10 / 100 / 1000 Mbps auto-sensing, PoE as per IEEE 802.3af

ETH2 10 / 100 / 1000 Mbps, precongured LAN port, re-congurable to WAN port

External antenna
connectors
(only OAP-1702B)

Declaration of conformity

Hereby, LANCOM Systems declares that this radio equipment is in compliance with Directive 2014/53/EU. The full text
of the EU declaration of conformity is available at the following internet address: www.lancom-systems.com/ce/

Package content

Cables Water-resistant, UV-resistant Ethernet cable with screw connector, 15 m

Documentation Quick Reference Guide (DE/EN), Installation Guide (DE/EN)

External antennas
(only OAP-1702B)

Mounting kit Equipment for wall and pole mounting, screws included

Covering cap Ensures that the unit remains sealed in case an Ethernet port is unused

PoE injector Gigabit Ethernet PoE injector (IEEE 802.3at)

Grounding cable To avoid electrostatic charge

Note: For installation in salt water environments please use a suitable outer housing.
Dimensions 255 × 250 × 70 mm (length/width/depth)

(restrictions vary between countries)

Up to 8.1 dBi at 5 GHz, up to 8.0 dBi at 2.4 GHz, and up to 5.0 dBi at Bluetooth

Transmission-power reduction in software by 1 dB steps to min. 0.5 dBm

Up to 13 channels, max. 3 non-overlapping (2.4-GHz band)

DFS for automatic dynamic channel selection required)

Scanner: The device can capture neighborhood BLE devices and transmit data to external
systems for evaluation.

Wi-Fi: 7 NJ connectors (3 for 2.4 GHz Wi-Fi module, 4 for 5 GHz Wi-Fi module),
BLE: 1 NJ connector

Eight 3 dBi dipole dualband Wi-Fi antennas

LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may

be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes.

LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omissions. 111853/0819

Installing access points and/or external an­tennas without adequate lightning protection
can lead to serious damage to the devices
and/or to the related network infrastructure.

The housing of the device may become warm during operation.
If the device is operated with outside temperatures exceeding 60 °C, it should be mounted with protection against contact.
When operating both Wi-Fi modules in the same frequency band, mutual interference cannot be ruled out.

Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!

*) The additional power LED statuses are displayed in 5-seconds

rotation if the device is congured to be managed by the LANCOM

Management Cloud.

MOUNTING AND CONNECTING THE DEVICE

TECHNICAL DETAILS