Lancom LN-1702, LN-1700 User Manual

MOUNTING AND CONNECTING THE DEVICE

TECHNICAL DETAILS

DC 12 V ResetETH1 (PoE) Config (Com)

LANCOM LN-1700

4

5

LANCOM LN-1702

Quick Reference Guide

Cloud-ready

Hardware

Power supply 12 V DC, external power adapter (110 V or 230 V) with bayonet connector to secure against

Power consumption Approx. 21 W via 12 V / 2 A power adapter (value refers to the total power consumption of

a

cb d

Wi-Fi antennas (only LN-1702)

a

Screw the two supplied Wi-Fi antennas onto the connectors WLAN 1 Ant 1 / Ant 2

and WLAN 2 Ant 1 to Ant 4. The desired MIMO behaviour can be congured under

> Physical WLAN Settings
> Radio
> Antenna grouping

Power

b

After connecting the cable to the device, turn the connector 90° clockwise to
prevent it from accidental un plugging. Use only the supplied power adapter.

Ethernet interface

c

Use the cable with the Ethernet connectors to connect interface ETH1 (PoE)
or ETH2 to your PC or a LAN switch.

Serial interface

d

You can optionally congure the device by connecting it to a PC with a
conguration cable (separately available).

Please observe the following when setting up the device

WLAN 2 Ant 4

WLAN 2 Ant 3

WLAN 2 Ant 1

WLAN 1 Ant 1WLAN 1 Ant 2

WLAN 2 Ant 2

a

a b

a Power

Off Device switched off

Green, permanently* Device operational,

Orange, permanently No adequate PoE-power supply via

Red / green, blinking Conguration password not set. Without a

Orange / green,
blinking alternately
with the WLAN link
LED

Orange / red,
blinking alternately
with the WLAN link
LED

1x green inverse
blinking*

2x green inverse
blinking*

3x green inverse
blinking*

resp. device paired / claimed and LANCOM
Management Cloud (LMC) accessible.

802.3af, operation of the second Wi-Fi
interface not possible

conguration password, the conguration

data in the device is unprotected.

At least one Wi-Fi module is in
managed mode and has not found a
WLAN controller yet. The corresponding
Wi-Fi module(s) is/are switched off until a
WLAN controller has been found to supply

a conguration, or until being switched

manually into another operating mode.

At least one Wi-Fi module is in managed
mode and has found a WLAN controller.
However, the WLAN controller cannot

assign a conguration because the
rmware and/or the device's loader

version is not compatible with the WLAN
controller.

Connection to the LMC active, pairing OK,
claiming error.

Pairing error, resp.
LMC activation code / PSK not available.

LMC not accessible, resp.
communication error.

b WLAN link

Off No Wi-Fi network dened or Wi-Fi module

deactivated. The Wi-Fi module is not
transmitting beacons.

Green, permanently At least one Wi-Fi network dened and

Wi-Fi module activated. The Wi-Fi module
is transmitting beacons.

Green, inverse ashing Number of ashes = number of connected

Wi-Fi stations and P2P wireless
connections, followed by a pause (default).

Alternatively the ashing frequency can
indicate signal strength over the dened

P2P link or the signal strength between the
access point and the device operating in
client mode.

Green, blinking DFS scanning or other scan procedure

Red, blinking Wi-Fi module hardware error

Environment Temperature range 0–45 °C (vertical wall mount with LANCOM Wall Mount (LN)),

Housing Robust synthetic housing, rear connectors, ready for wall and ceiling mounting; measures

Number of fans None; fanless design, no rotating parts, high MTBF

Wi-Fi

Frequency band 2400-2483.5 MHz (ISM) or 5180-5700 MHz (restrictions vary between countries)

Radio channels 2.4 GHz Up to 13 channels, max. 3 non-overlapping (2.4 GHz band)

Radio channels 5 GHz Up to 19 non-overlapping channels (automatic dynamic channel selection required)

Interfaces

ETH1 (PoE) 10 / 100 / 1000 Base-TX, autosensing, auto node hub, line bundling via LACP,

ETH2 10 / 100 / 1000 Base-TX, autosensing, auto node hub, line bundling via LACP

Serial interface Serial conguration interface / COM-port (8-pin mini-DIN): 9,600 - 115,000 baud

Declaration of conformity

Hereby, LANCOM Systems declares that this radio equipment is in compliance with Directive 2014/53/EU. The full text

of the EU declaration of conformity is available at the following internet address: www.lancom-systems.com/ce/

Package content

Manual Installation Guide (DE / EN), Quick Reference Guide (DE / EN)

Antennas
(only LN-1702)

Cable Ethernet cable, 3 m

Power adapter External power adapter, NEST 12 V / 1.5 A DC/S, barrel connector 2.1 / 5.5 mm bayonet,

disconnection or PoE based on 802.3at via ETH1

access point and power adapter),
Approx. 19.4 W via PoE (value solely refers to the power consumption of the access point)

0-37 °C (horizontal ceiling mount with LANCOM Wall Mount (LN))
Access point overheating is avoided by automatic throttling of the Wi-Fi modules
Humidity 0-95 %; non-condensing

205 x 42 x 205 mm (W x H x D)

PoE adapter compliant to IEEE 802.3at required

Six 3dBi dipole dual-band antennas

LANCOM item no. 111507 (EU, 230 V); LANCOM item no. 111302 (UK, 230 V)

LANCOM, LANCOM Systems and LCOS are registered trademarks. All other names or descriptions used may be trademarks or registered

trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions. 111720/0118

A For devices to be operated on the desktop, please attach the adhesive rubber

footpads

A Do not rest any objects on top of the device
A Keep the ventilation slots on the side of the device clear of obstruction
A Lockable wall and ceiling mounting with the LANCOM Wall Mount (LN)

(available as an accessory)

Please note that when operating both Wi-Fi modules in the same frequency band, mutual
interference cannot be ruled out

*) The additional power LED statuses are displayed in 5-seconds

rotation if the device is congured to be managed by the LANCOM

Management Cloud.