La Crosse Technology WS-8025OAK, WS-8025AL, WS-8025CH User Manual

WS-8025U
Wireless Weather Center with
Sun/Moon Time
Instruction Manual
RADIO CONTROLLED
TIME DATE
SUNRISE MOON PHASE
PM PM
SUNSET
INDOOR TEMPERATURE
TENDENCY
PRESSURE
rel
PRESSURE HISTORY
OUTDOOR TEMPERATURE
LO MINHIMAX
MOONRISE +1
LOCATION MOONSET
HUMIDITY
inHg
-1h-3h-6h-9h-12h-18h-24h-30h
+1
+0.5
+0.2
0
HUMIDITY
2
%RH%
MIN MAX
%
RH
+7 +5 +3 +1
0
-1
-3
-5
-7
01
+4
+2
%
RH
RH
FCC ID: OMO-01TX (transmitter), OMO-01RX (receiver)
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
OUT
ALARM
SET
IN
SUN/
MOON
CH
+ –
REMOTE
THERMO-SENSOR
433 MHz
Contents
Language Page English 2
French 22 Spanish 42
TABLE OF CONTENTS
Topic Page
Inventory of Contents/ Additional Equipment 3 About WWVB 3 Quick Set Up Guide 3-4
Detailed Set Up Guide
Battery Installation 4 Start Up Sequence 5 Explanation of LCD Information 6 Function Key Layout 6
Program Mode
Time, 12/24 Hour Mode and Date Setting 7 City Location Setting 7-8 U.S. City Codes 8-10 Canada City Codes 11 Mexico City Codes 11 Time Zone and Daylight Saving Time (DST) Setting 11 Weather Measuring Units 11-12 LCD Contrast 12
Features and Operation
Sun Rise/Set and Moon Rise/Set Calculation 12-13 Moon Phase 13 Minimum/Maximum T emperature/Humidity 14 Multiple Remote Transmitters 14-15 Remote T emperature Alarm 15 Comfort Indicator 15 Weather Forecast Icon and Pressure Trend 15 Weather Tendency Arrows 16 Storm Warning Alarm 16 Two Hour Air Pressure Tendency Chart 17 Barometric Air Pressure Reading 17 Air Pressure History Bar Chart 17 Mounting 17-18 Maintenance and Care 19 Troubleshooting Guide 19 Specifications 19-20 Warranty Information 20-21
6-12
INVENTORY OF CONTENTS
1. WS-8025U-indoor weather station
2. TX4U-remote thermo/hygro (temperature/humidity) sensor
3. Instruction manual and warranty card
RADIO CONTROLLED
TIME DATE
WWWB
SUNRISE MOON PHASE
MOONRISE +1
PM PM
SUNSET
LOCATION MOONSET
INDOOR TEMPERATURE
HUMIDITY
%
TENDENCY
PRESSURE
PRESSURE HISTORY
OUTDOOR TEMPERATURE
LO MINHIMAX
REMOTE
THERMO-SENSOR
433 MHz
RH
rel
inHg
+7 +5 +3 +1 0
-1
-3
-5
-7
-1h-3h-6h-9h-12h-18h-24h-30h
01
+4
+2
+1
+0.5
+0.2
0
HUMIDITY
%
2
RH
%RH%
RH
MIN MAX
SUN/
IN
MOON
OUT
CH
ALARM
+
SET
ADDITIONAL EQUIPMENT (not included)
1. Five fresh AA 1.5V alkaline batteries.
2. One wall-mounting screw (optional)
ABOUT WWVB (radio-controlled time)
The NIST (National Institute of Standards and Technology-Time and Frequency Division) radio station, WWVB, is located in Ft. Collins, Colorado and transmits the exact time signal continuously throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away through the internal antenna in the indoor weather station. However, due to the nature of the Earth's Ionosphere, reception is very limited during daylight hours. The indoor weather station will search for a signal every night when reception is best. The WWVB radio station derives its signal from the NIST Atomic clock in Boulder, Colorado. A team of atomic physicists continually measure every second of every day to an accuracy of ten billionths of a second a day. These physicists have created an international standard, measuring a second as 9,192,631,770 vibrations of a Cesium 133 atom in a vacuum. For more information about WWVB please see the NIST website at http://www.boulder.nist.gov/timefreq/stations/wwvb.htm
QUICK SET-UP GUIDE
Hint : Use good quality Alkaline Batteries and avoid rechargeable batteries.
1. Have the indoor weather station and remote thermo/hygro sensor 3 to 5 apart.
2. Batteries should be out of both units for 10 minutes.
3. Place the batteries into the remote thermo/hygro sensor first then into the indoor weather station. (All remote thermo/hygro sensors must be started before the indoor weather station)
4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.
In this time the indoor weather station and remote thermo/hygro sensor will start to talk to each other and the indoor weather station will show both the indoor temperature and humidity and the outdoor temperature and humidity. If the indoor weather station does not display all values after the 10 minutes please retry the set up as stated above. After all values are displayed for 10 minutes you can place your remote thermo/hygro sensor outdoors and set your time.
GB
P.2
The remote thermo/hygro sensor should be placed in a dry, shaded area. The remote thermo/hygro sensor has a range of 80 feet. Any walls that the signal will have to pass through will reduce distance. An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance. Your distance plus resistance should not exceed 80 ft. in a straight line.
P.3
GB
NOTE
: Fog and mist will not harm your remote thermo/hygro sensor but direct rain must be avoided.
II. Start Up Sequence
T o complete the set up of your indoor weather station after the 10 minutes have passed please follow the steps in the Detailed Set Up Guide.
Note
: The remote thermo/hygro sensor transmits a signal every 5 minutes; after the batteries have been installed, the indoor weather station will search for the signal for a duration of 5 minutes. If there is no temperature reading in the OUTDOOR LCD after 5 minutes, make sure the units are within range of each other, or repeat the battery installation procedure.
DETAILED SET-UP GUIDE
I. Battery Installation
Batteries will fit tightly. To avoid start-up problems, make sure that the batteries do not spring free. Also be sure to insert alkaline batteries into the remote thermo/hygro sensor first, then the indoor weather station. Initial set up should be done with the remote thermo/hygro sensor and indoor weather station in the same room. The units should be permanently mounted only after the signal reception has been verified.
Mounting Bracket/Recent
+
SIZE AA LR6
SIZE AA LR6
Rain Cover
REMOTE
THERMO-SENSOR
433 MHz
Thermo-Hygro Transmitter
+
A. Remote Temperature and Humidity Sensor, TX4U
1. Pull the cylindrical rain cover off the transmitter.
2. Remove the battery cover (located on the backside of the transmitter, above the mounting post and bracket). Press the arrow and slide the battery cover off.
3. Observing the correct polarity install 2 Alkaline AA batteries.
4. Replace battery cover, and place rain cover snugly onto the transmitter.
B. Weather Center
1. Remove the battery cover (the cover has white writing on it).
2. Observe the correct polarity, and install three Alkaline AA batteries.
3. Do not press any buttons for at least ten minutes. If a button is pressed before the Weather Center has received information from the TX4U sensor , no data will be received from that sensor until reset.
4. Replace the battery cover.
Battery Cover
A. Initial Start
1. Immediately after the batteries have been installed, the indoor weather station will sound a "beep", and the LCD will completely light up for a brief moment.
2. All information will then appear in normal mode, with "12:00" as the default time and "1.1" as the default date (2001 as the year).
3. "DCA" is the default city (Washington, DC, USA), with the sunrise, sunset, moonrise and moonset times displayed for that city at that date.
4. The indoor temperature and humidity, and barometric air pressure (as 29.91 inHg relative RH) will also be displayed.
5. There is a "satellite" icon that appears near the bottom of the LCD, to the right of the "max" remote temperature-this icon informs the user that the indoor weather station is looking for signals from the remote thermo/hygro sensor. Within five minutes the remote temperature and humidity should be displayed-if not, remove batteries from all units and repeat battery installation, the remote temperature sensor first, then the indoor weather station.
B. WWVB Reception
1. Once the batteries are installed in the Weather Center, it will automatically search for the WWVB signal. If it receives a good signal (which is unlikely during daylight hours in most locations), the WWVB reception indicator (looks like a tower icon) will flash. The indoor weather station requires five full minutes of good reception to successfully capture the signal and set to the correct hour, minute, second, month, day and year. If the signal reception is not successful within ten minutes, the signal search will be cancelled and will automatically resume every two hours until the signal is successfully captured.
2. The signal is sent from Ft. Collins, Colorado only and is similar to an AM radio signal. Atmospheric interferences such as storms, sunspots, and even sunlight will cause the signal to not travel as far.
3. To maximize reception, place the indoor weather station in a window facing Colorado, at least six feet from any electrical source (computers, televisions, refrigerators, etc.). Do not move the indoor weather station while it is searching for the signal.
4. The time and date can be manually set. Once the signal is captured, it will override any time and date set to the time zone selected.
5. Once the time and date are set, the indoor weather station will conduct a search every night at midnight and correct to the accurate time and date (Daylight Saving Time is automatic). If the signal has been received in the past 24 hours, the reception indicator will be displayed.
GB
P.4
SIZE AA LR6
+
SIZE AA LR6
+
SIZE AA LR6
+
P.5
GB
III. Explanation of LCD Information
A. The below picture highlights the LCD features
WWVB reception indicator
Radio-controlled time
Sunrise time for
selected location
Sunset time for
selected location
City code for city selected
(San Francisco, USA shown)
Indoor temperature
Air pressure tendency arrow
(increase displayed)
Relative or absolute air pressure
selection (relative shown)
Barometric air pressure
Pressure change over
last two hours (in hPa)
(+4 hPa shown)
Remote temperature Remote temperature
minimum and maximum
OR alarm setting
TIME DATE
WWWB
SUNRISE MOON PHASE
PM PM
SUNSET
INDOOR TEMPERATURE
TENDENCY
PRESSURE
PRESSURE HISTORY
OUTDOOR TEMPERATURE
LO MIN
LOCATION MOONSET
rel
HI MAX
0
+0.2
2
MIN MAX
+0.5
MOONRISE +1
HUMIDITY
inHg
+1
HUMIDITY
%RH%
RH
-1h-3h-6h-9h-12h-18h-24h-30h
+2
%
+7 +5 +3 +1
0
-1
-3
-5
-7
01
+4
%
RH
RH
Alarm on indicator
Radio-controlled date Moonset time for
selected location Current moon phase
Moonset time for selected location
Indoor humidity Comfort icon
Forecast icon
Measuring unit for air pressure, inHg shown
Last 30 hour air pressure graph
Remote humidity Remote sensor number
(up to three total) Remote humidity
minimum and maximum
B. There are many different modes the indoor weather station can be set to. The LCD shown
is the normal operating mode, and your actual data shown will be different based on your local settings and conditions.
IV. Function Key Layout
A. The below picture shows the eight function keys used in programming and operation of
your indoor weather station.
MIN MAX MIN MAX
IN
OUT
ALARM
SET
MOON
SUN/
CH
+ –
V. Program Mode
The program mode is laid out in a manner that allows you to program each function separately, or you can follow the instructions entirely to program the indoor weather center. Complete programming is usually done for the initial set-up, and will require you to skip step 1 and 2 of each programming section. The programming mode can be exited at any time by either pressing the "CH" button, or waiting for the 16-second time-out to take effect.
A. Overview of programming mode sequence
Note
: If the country setting is other than USA step 8 is city, step 9 is time zone, etc.
1. Hour 2. Minute 3. 12/24 hour 4. Year
5. Month 6. Date 7. Country 8. State
9. City 10. Time Zone 11. DST on/off 12. ˚F/˚C
13. inHg/hPa 14. Relative pressure 15. Forecast 16.Storm warning setting sensitivity setting
17. Storm alarm 18. LCD contrast 19. LI on/off
on/off
B. Time, 12/24 Hour Mode and Date Setting
The WWVB signal will override any manual set time and date information. The time will be based on the time zone selected.
1. Press and hold the "
SET
" button for 1 second.
2. The hour is now flashing.
3. Press and release the "+" or "-" button to select the current hour.
Note
: In 12h mode "PM" will appear to the left of the time during PM hours. If the time is not within the PM hours nothing will be displayed. Be sure to set the time to the correct AM/ PM time to ensure automatic reception.
4. Press the "
SET
" button to advance to the minute
5. The minute is now flashing.
6. Press and release the "+"or "-" button to select the current minute.
7. Press and release the "
SET
" button to advance to the 12/24-hour setting.
8. "12" is now flashing.
9. Press and release the "+"or "-" button to select either 12 (am/pm) or 24 hour (military)
time format.
10. Press and release the "
SET
" button to advance to the year setting.
11. The year is now flashing.
12. Press and release the "+"or "-" button to select the current year.
13. Press and release the "
SET
" button to advance to the month setting.
14. The month is now flashing.
15. Press and release the "+"or "-" button to select the current month.
16. Press and release the "
SET
" button to advance to the date setting.
17. The date is now flashing.
18. Press and release the "+"or "-" button to select the current date.
19. Press and release the "
SET
" button to advance to the location setting (skip steps 1 and
2 in section B if continuing).
C. City Location Setting
The list of the cities available is listed after this section.
1. Press and hold the "
2. Press and release the "
SET
" button for 1 second.
SET
" button 6 times.
3. The country location will flash (USA default/factory setting).
4. Press and release the "+"or "-" button to select the country (USA=United States,
CAN=Canada, MEX=Mexico).
5. Press and release the "
SET
" button to advance to the state setting (USA only) or the
city location (Canada or Mexico).
GB
P.6
P.7
GB
Skip to step nine if Mexico or Canada is selected
6. The state is now flashing.
7. Press and release the "+"or "-" button to select the state.
8. Press and release the "
9. The city is now flashing.
10. Press and release the "+"or "-" button to select the city closest to your location (abbreviated by airport code, if applicable).
11. Press and release the " and 2 in section D if continuing).
SET
" button to advance to the city setting.
SET
" button to advance to the time zone setting (skip steps 1
Section C lists the available city codes. Section D continues with the setup programming.
D. City Location Listing
The following list of city locations is entered in the database. Due the limited memory, 245 cities are listed. Every attempt has been made to provide a location close to all parts of North America. The choices were based first on state capitals, then nearby locations based on population and difference of latitude and longitude. There are cases where your city may be closer to a city in a nearby state rather than your state. We are unable to change the database, but are open to suggestions for future locations. If you feel there is a city that should be listed, please write to us (either mail or e-mail).
United States Cities, Listed by State
Code State/City Code State/City Code State/City AK Alaska CA California (cont.) GA Georgia
ANC Anchorage SAC Sacramento ABY Albany FAI Fairbanks SAN San Diego AGS Augusta JNU Juneau SBD San Bernardino ATL Atlanta OME Nome SFO San Francisco CSG Columbus AL Alabama CO Colorado MAC Macon BHM Birmingham DEN Denver SAV Savanna GAD Gadsden DRO Durango HI Hawaii MGM Montgomery FNL Ft. Collins HNL Honolulu MOB Mobile GJT Grand Junction ITO Hilo AR Arkansas ITR Burlington OGC Kahului FSM Fort Smith PUB Pueblo WAI Waimea LIT Little Rock CT Connecticut IA Iowa TXK Texarkana HFD Hartford ALO Waterloo AZ Arizona DC District of Columbia DSM Des Moines FLG Flagstaff DCA Washington DVN Davenport PHX Phoenix DE Delaware SUX Sioux City TUS Tucson 0N5 Dover ID Idaho YUM Yuma FL Florida BOI Boise CA California EYW Key West GIB Gibbonsville BFL Bakersfield JAX Jacksonville PIH Pocatello BLH Blythe MIA Miami SZT Sand Point EKA Eureka ORL Orlando IL Illinois FAT Fresno PNS Pensacola CMI Champaign FTB Ft. Bragg TLH Tallahassee ORD Chicago LAX Los Angeles TPA T ampa SPI Springfield ROD Redding
IN Indiana MN Minnesota ND North Dakota, cont.
EVV Evansville AEL Albert Lea GFK Grand Forks HUF Terre Haute BJI Bemidji NE Nebraska IND Indianapolis DLH Duluth GRI Grand Island SBN South Bend GPO Grand Portage LNK Lincoln KS Kansas INL International Falls OMA Omaha DDC Dodge City STP St. Paul SNY Sidney K32 Wichita MO Missouri VTN Valentine KCK Kansas City JEF Jefferson City NH New Hampshire OH1 Wakeeney MKC Kansas City CON Concord TOP Topeka MPH Memphis NJ New Jersey KY Kentucky POF Poplar Bluff EWR Newark FFT Frankfort SGF Springfield TTN Trenton LEX Lexington STL St. Louis NM New Mexico LOU Louisville MS Mississippi ABQ Albuquerque LA Louisiana GWO Greenwood MAG Magdalene BTR Baton Rouge HUV Huntsville ROW Roswell CWF Lake Charles JAN Jackson RTN Raton IER Natchitoches TUP Tupelo SAF Santa Fe NEW New Orleans MT Montana NV Nevada SHV Shreveport BIL Billings AIN Austin MA Massachusetts FTP Ft. Peck CXP Carson City BOS Boston GFT Great Falls ELY Ely MD Maryland HLN Helena LAS Las Vegas BWI Baltimore SDY Sidney LWL Wells ME Maine WTF Whitefish RNO Reno AUG Augusta NC North Carolina NY New York BGR Bangor AVL Asheville ALB Albany CAR Caribou CLT Charlotte BUF Buffalo PWM Portland FAY Fayetteville JFK New York City MI Michigan ILM Wilmington LKP Lake Placid AZO Kalamazoo INT Winston-Salem SYR Syracuse DET Detroit MCZ Williamston OH Ohio FNT Flint RDU Raleigh CLE Cleveland LAN Lansing ND North Dakota CMH Columbus PZQ Rogers City BIS Bismarck ISZ Cincinnati SAW Marquette BWB Bowbells TOL Toledo TVC Traverse City FAR Fargo YNG Youngstown
GB
P.8
P.9
GB
OK Oklahoma TX Texas (cont.) WV West Virginia
17K Boise City DFW Dallas/Ft. Worth CRW Charleston LAW Lawton ELP El Paso HLG Wheeling OKC Oklahoma City HOU Houston WY Wyoming TUL Tulsa LRD Laredo BYG Buffalo OR Oregon ODO Odessa CPR Casper BNO Burns SAT San Antonio CYS Cheyenne EUG Eugene UT Utah LAA Little America MFR Medford SAL Saline WYE West Y ellowstone PDX Portland SGU St. George SLE Salem SLC Salt Lake City PA Pennsylvania TSN Thompson CXY Harrisburg VA Virginia PHL Philadelphia DON Vienna PIT Pittsburgh LYH Lynchburg SCR Scranton ORF Norfolk PR Puerto Rico RIC Richmond SJU San Juan ROA Roanoke
RI Rhode Island VT Vermont
PVD Providence BTV Burlington SC South Carolina MPR Montpelier CHS Charleston WA Washington CUB Columbia ABE Aberdeen GMU Greenville ALW Walla Walla SD South Dakota KTF Kettle Falls FSD Sioux Falls MVN Mt. Vernon PIR Pierre OLM Olympia RAP Rapid City SEA Seattle TN Tennessee SFF Spokane BNA Nashville TON Tonasket CHA Chattanooga YKM Yakima DKX Knoxville WI Wisconsin MEM Memphis AUW Wausau TX Texas GRB Green Bay
ABI Abilene LSE La Crosse AMA Amarillo MSN Madison AUS Austin MWC Milwaukee BRO Brownsville SSQ Spooner
Canada City Listing
Code City Code City Code City
EDM Edmonton YEL Yellowknife CHT Charlotte Town ALB Calgary OTT Ottawa MON Montreal VAN Vancouver SUD Sudbury QUE Quebec WIN Winnipeg THU Thunder Bay REG Regina FRE Fredericton TOR Toronto WHI Whitehorse HAL Halifax
Mexico City Listings
Code City Code City Code City
CHH Chihuahua MEX Mexico City HER Hermosillo DUR Durango GUA Guadalupe
E. Time Zone and Daylight Saving Time Settings
1. Press and hold the "
2. Press and release the "
3. The time zone will now flash based on the city selected.
4. Press and release the "+"or "-" button to adjust to the correct time zone.
5. Press and release the "
6. "dst ON" will now flash.
7. Press and release the "+" or "-" button to select DST 1 (recognizes Daylight Saving Time change) or DST 0 (does not change with Daylight Saving Time).
Note
: Some locations (Arizona and parts of Indiana) do not follow Daylight Saving Time.
8. Press and release the " settings (skip steps 1 and 2 in section E if continuing).
F. Weather measurement units (˚F/˚C, inHg/hPa)
1. Press and hold the "
2. Press and release the "
3. The selected temperature units will now flash (˚F default/factory setting).
4. Press and release the "+"or "-" button to select ˚F (Fahrenheit) or ˚C (Celsius).
5. Press and release the " setting.
6. The selected air pressure units will now flash (inHg default/factory setting).
7. Press and release the "+"or "-" button to select inHg (inches of Mercury) or hPa (hectopascal or millibars).
8. Press and release the " setting.
9. The air pressure reading will now flash (29.91 inHg, 1012.8 hPa as default).
10. Press and release the "+"or "-" button to adjust to the correct relative air pressure based on local reports.
11. Press and release the "
Note
: Barometric air pressure is usually reported as "relative air pressure". This reading is based on the combination of absolute air pressure and altitude. In general, an increase in altitude will result in a decrease in air pressure. Relative air pressure will make readings in nearby locations relative to each other to allow for proper forecasting. The absolute air pressure reading in the Weather Center cannot be calibrated, only the relative air pressure.
SET
" button for 1 second.
SET
" button 9 times.
SET
" button to advance to the Daylight Saving Time setting.
SET
" button to advance to the weather measurement units
SET
" button for 1 second.
SET
" button 11 times.
SET
" button to advance to the barometric air pressure units
SET
" button to advance to the barometric air pressure calibration
SET
" button to advance to the forecast sensitivity setting.
GB
P.10
P.11
GB
New Moon
Waxing Crescent Waxing Gibbous
First Ouarter
Full Moon
Waning Gibbous Waning Crescent
Last Ouarter
12. The selected forecast sensitivity setting will now flash (0.09 inHg default).
13. Press and release the "+"or "-" button to select 0.06, 0.09, or 0.12 inHg (if hPa is selected, the choices will be 2, 3, or 4). A lower setting will result in a quicker change in the forecast icon. In other words, if the setting is 0.06 inHg, the forecast icon will change if the air pressure changes by at least 0.06 inHg within a six-hour period. This is useful, as certain areas will have a change of air pressure but no change in weather.
14. Press and release the "
SET
" button to advance to the storm warning setting.
15. The selected storm warning level will now flash (0.15 inHg, 5 hPa default).
16. Press and release the "+"or "-" button to select the storm warning setting. This can be set to 0.09, 0.12, 0.15, 0.18, 0.21, 0.24, or 0.27 inHg (from 3 to 9 hPa). This setting will determine how much of a drop in air pressure over six hours will sound the storm warning alarm.
17. Press and release the "
SET
" button to advance to the storm warning alarm on/off
setting.
18. The storm warning on or off setting will now flash (AOFF default/factory setting).
19. Press and release the "+"or "-" button to select whether or not the storm warning alarm is activated.
20. Press and release the "
SET
" button to advance to the LCD setting (skip steps 1 and 2
in section F if continuing).
f. Press and release the "+" or "-" key to select the state (see listing on pages 8 to 11). g. Press and release the "
SET
" key to advance to the city selection. h. The city is now flashing. i. Press and release the "+" or "-" key to select the city. j. Press and release the "
SET
" key to advance to the date setting.
If the sunrise/set moonrise/set times are desired for the current date, the "SUN/MOON" key may be pressed to calculate. Skip to step t for further explanation.
k. The year is now flashing (the current year). l. Press and release the "+" or "-" key to select the year desired. m. Press and release the "
SET
" key to advance to the month setting. n. The month is now flashing (the current month). o. Press and release the "+" or "-" key to select the month desired. p. Press and release the "
SET
" key to advance to the date setting. q. The date is now flashing (the current date). r. Press and release the "+" or "-" key to select the date desired. s. Press and release the "
SUN/MOON
" key to calculate the new city location at the date
selected.
G. LCD Contrast
FEATURES AND OPERA TIONS
A. Sunrise/set and Moonrise/set Calculation
The indoor weather station will calculate the sunrise/set moonrise/set each day based on the location entered through the programming mode. To view another location and/or date without affecting the programmed city location and date, follow section A.2 in Features and Operations.
1. Daylight Hours and Minutes Calculation
2. View Different Location/Time for Sunrise/set and Moonrise/set
GB
P.12
1. Press and hold the "
2. Press and release the "
SET
" button for 1 second.
SET
" button 17 times.
3. The LCD contrast setting will now flash (4 is the default/factory setting).
4. Press and release the "+"or "-" button to select the contrast level desired (from 1 to 8).
5. Press and release the "
SET
" button to advance to the LI setting.
6. The LI setting will now flash (ON is the default/factory setting).
7. Press and release the "+"or "-" button to select ON or OFF.
8. Press and release the "
Note
: The LI setting does not affect the function of the indoor weather station and is
SET
" button to exit the programming mode.
present only for future use.
Press and release the "SUN/MOON" button. In place of the sunrise/sunset time will be the number of daylight hours and minutes. Press the "SUN/MOON" button to view the sunrise/ sunset time again.
If no buttons are pressed in 30 seconds during this selection the indoor weather station will revert to the normal mode. Alternatively, you may press the "CH" key to revert to the normal mode.
a. Press and hold the "
SUN/MOON
" key for at least two seconds. b. The selected country will now flash. c. Press and release the "+" or "-" key to select the desired country. d. Press and release the "
SET
" key to advance to the state selection (or city if Canada or
Mexico is selected skip to step h.).
e. The state is now flashing.
You may instead press the "SET" key to select a different location, starting at step b above.
t. Once the "SUN/MOON" key is pressed, the sunrise/set and moonrise/set times will
flash as dashes while the indoor weather station calculates the times (the moon phase is calculated, also). Once the times are displayed, the indoor weather station will remain in this mode for 30 seconds or until the "
CH
" key is pressed. The year, month, or date will also be flashing. At this time it is possible to start at step b. to select another date or location.
u. Once this mode is exited either through timeout after 30 seconds or by pressing the
"
CH
" button, the indoor weather station will revert to the normal mode with the location and date set through the programming mode. The indoor weather station will default to the last city selected when this mode is entered again.
B. Moon Phase
1. There are 12 moon phases shown on the indoor weather station; the black portion signifies the portion of the moon visible in the sky. Thus, when the moon icon is all black, it is a full moon. The indoor weather station is programmed with all moon phases from the year 2000 until 2099.
2. The moon phase for any date may be found by selecting a different date through the sun rise/set moon rise/set programming section (section A in Features and Operations).
P.13
GB
C. Minimum and Maximum Temperature and Humidity
1. Indoor Minimum and Maximum Temperature and Humidity
The indoor weather station automatically stores the minimum and maximum indoor temperature and humidity. The minimum and maximum values are updated automatically when a new minimum or maximum is recorded, or until manually reset.
a. From the normal display mode, press and release the "
minimum temperature and humidity ("MIN" will be displayed near the indoor temperature and humidity).
b. Press and release the "
humidity.
c. Press and release the "
minimum/maximum values will occur if no keys are pressed for fifteen seconds).
IN
" key again to view the indoor maximum temperature and
IN
" key again to return to the normal mode (timeout of viewing
IN
" key once to view the indoor
2. Viewing and Operating with Multiple Remote Sensors
a. To view the temperature of a different remote sensor press and release the "
button. A shift from one "boxed" number to the next should be observed in the OUTDOOR LCD.
b. The minimum and maximum temperature of the additional remote sensor will be
displayed below the current temperature of the remote sensor in the OUTDOOR LCD.
c. To reset the minimum and maximum temperature readings press and hold the "
button for 5 seconds and the records for all the remote sensor will be reset.
Each remote sensor will have its own minimum and maximum values stored, as well as its own alarm settings for temperature. Resetting the outdoor minimum and maximum values will reset all remote sensors' recordings.
E. Remote Temperature Alarm
CHANNEL
RESET
"
"
Note
: To reset the indoor minimum and maximum temperature and humidity, press and
hold the "IN" key for at least two seconds.
2. Outdoor Minimum and Maximum Temperature and Humidity
The indoor weather station automatically stores the minimum and maximum outdoor temperature and humidity. The minimum and maximum values are updated automatically when a new minimum or maximum is recorded, or until manually reset.
a. The outdoor (remote) minimum and maximum temperature values are displayed below
the outdoor temperature display.
b. These values are rounded down for minimum and rounded up for maximum.
Note : The temperature alarm mode shares the same display. When the alarm values are
displayed, "ALARM" will be displayed above the remote temperature. To switch back and forth between views, press the "OUT" key.
c. To reset the outdoor minimum and maximum temperatures press and hold the "CH"
key for at least one second.
D. Multiple Remote Temperature Sensors
The WS-8025U is able to receive signals from 3 different remote sensors. These extra remote sensors can be purchased through the same dealer as this unit. A TX4U will monitor the temperature and humidity, a TX3U will monitor temperature and display the temperature on its LCD and the TX3UP will monitor the temperature via a probe for measuring soil or water temperatures.
Note
: When setting up multiple units it is important to insert batteries first into all the remote sensors, and in numeric sequence. Second install batteries into the indoor weather station. Transmission problems will arise if this is not done correctly and if the total time for set-up exceeds 6 minutes
1. Set Up of Multiple Units
a. It is necessary to remove the batteries from all units currently in operation. b. Remove the battery covers to all remote sensors. c. Place all remote sensors in a numeric sequential order. d. In sequential order, install batteries following the same battery installation procedures
seen in Detailed Set-Up Guide section of this manual. e. Install batteries into the indoor weather station. f. Follow the Detailed Set-Up Guide for programming and operating instructions.
1. Activating the alarm
From the normal mode, press and release the " alarm and minimum/maximum values. " temperature display; this will also activate the temperature alarm.
2. Setting the temperature alarm
a. Press and hold the " b. The low temperature will be flashing (32˚F default/factory setting). c. Press and release the "+" or "-" key to adjust the temperature from -22˚F to +157˚F
("- -" if outside this range). Any value attained below this will sound the alarm. d. Press and release the " e. The high temperature setting is now flashing (86˚F default/factory setting). f. Press and release the "+" or "-" key to adjust the temperature from -22˚F to +157˚F
("- -" if outside this range). Any value attained above this value will sound the alarm. g. Press and release the "
will timeout after fifteen seconds and return to the normal mode automatically).
3. Canceling the Temperature Alarm While Sounding
a. While the alarm is sounding, press any key to mute the alarm. The temperature will
flash as long as the value is above the set value. b. The alarm will reactivate automatically once the value has fallen below the set value,
or if a new value is entered.
F. Comfort Indicator for Indoor Temperature and Humidity
1. The comfort level indicator appears inbetween the indoor tempearture and humidity.
2. The indicator will display a "happy-face" when the temperature is between 68˚F and 79˚F (20˚C and 25.9˚C), and the humidity is between 45% and 64%.
3. A "sad-face" will be displayed when the temperature and humidity are outside the mentioned ranges.
4. If the humidity is below 45% the word "DRY" will appear to the right of the "sad-face" icon.
5. If the humidity is above 54% the word "WET" will appear to the right of the "sad-face" icon.
G. Weather Forecast Icon and Pressure Trend Indicators
The weather forecasting feature is estimated to be 75% accurate, and is based solely upon the change of air pressure over time. The WS-8025U averages past air-pressure readings to provide an accurate forecast-creating a necessity to disregard all weather forecasting for 12­24 hours after the unit has been set-up, reset, or moved from one altitude to another (i.e. from one floor of a building to another floor). In areas where the weather is not affected by the change of air pressure, this feature will be less accurate.
OUT
" key for two seconds.
SET
" key to advance to the high temperature alarm.
SET
" key to return to the normal display mode (or the display
OUT
ALARM
" key to toggle between the temperature
" will be displayed above the remote
GB
P.14
P.15
GB
1. Weather Icons
a. There are 3 possible weather icons that will be displayed at various times in the
center of the indoor weather station.
i
Sunny
- indicates that the weather is expected to improve (not that the weather
will be sunny).
ii
Sun with Clouds
weather will be sunny with clouds).
iii
Clouds with Rain
the weather will be rainy).
b. The weather icons change when the unit detects a change in air pressure. c. The icons change in order, from "sunny" to "sun with clouds" to "clouds with
rain" or the reverse.
d. It will not change from "sunny" directly to "clouds with rain", although it is possible
for the change to occur quickly.
e. If the symbols do not change, the weather has not changed (or the change has
been slow and gradual).
f. The sensitivity of the change in foreacst icon is set by the user in section F of
the Detailed Set Up Guide.
H. Weather Tendency Arrows
Pressure trend arrow
1. Along with the forecast icon there is a pressure tendency arrow.
2. There is one that points up (on the left side of the LCD) and one that points down (on the right side of the LCD).
3. These arrows reflect current changes in the air pressure.
4. An arrow pointing up indicates that the air pressure is increasing and the weather is expected to improve or remain good.
5. An arrow pointing down indicates that the air pressure is decreasing and the weather is expected to become worse or remain poor.
6. No arrow means the pressure is stable.
7. A storm can be expected if there is a drop of 4 hPa or more in less than 6 hours. The clouds with rain icon will be displayed and the tendency arrow that points down will be flashing-indicating the storm warning feature has been activated. The flashing will stop when the air pressure stabilizes or begins to rise.
I. Storm Warning Alarm
1. An alarm can be set to warn of a drop in air pressure.
2. Please follow the programming instructions in section F of the Detailed Set Up Guide to activate this alarm
3. When the air pressure drops by the level set, an alarm will sound (if the alarm is activted).
4. To cancel the alarm while sounding press any key.
- indicates that the weather is expected to be fair (not that the
- indicates that the weather is expected to get worse (not that
J. Air Pressure Tendency for Past Two Hours
The bar below the air pressure history chart displays the air pressure change over the past two hours (values based on hPa change, 1 hPa equals 0.03 inHg).
K. Barometric Air Pressure Reading
1. The actual barometric air pressure is displayed directly under the weather forecast icon
2. The relative air pressure is calibrated by the user through the programming mode.
3. Please Follow the programming instructions in section F of the Detailed Set Up Guide to set this feature.
4. To toggle between absolute and relative air pressure, press the "-" key.
L. Air Pressure History Bar Chart
1. The bar graph shows in hPa (Hekto Pascal) the recorded air pressure over the past 30­hours.
2. The horizontal axis shows the hours at increments of -30 hours, -24 hours, -18 hours, -12 hours, -6 hours, -3 hours, -1 hours, and 0 hours (current).
3. The vertical axis is set by hPa: the "0" on this axis represents the current hPa, and + or
-1,3,5, or 7 shows (in hPa) how high or low the past air pressure was as compared to the current one.
4. The "0" on the vertical axis indicates the current air pressure value.
5. The "0h" on the horizontal axis indicates the current hour, thus the current air pressure also.
6. Each bar on the bar graph represents a value of 0.03 hPa, and each bar also has a corresponding value on the verticle axis.
7. Air pressure trends can be determined by simply glancing at the bar graph. a. If the bars are rising (higher on the right than the left) then the air pressure has a rising
trend, and the weather should improve.
b. If the bars are dropping (lower on the right than the left) then the air pressure has a
falling trend, and the weather should worsen.
8. Multiply the two values to find past air pressure (note the + or - sign of values on the verticle axis); i.e. 0.03 hPa x 3 = 0.09 hPa, now add this value to the air pressure (in LCD
4) to evaluate what past air pressures have been.
9. The bar chart will constantly scroll to avoid burnout of the LCD.
Note
: This feature cannot be turned off.
MOUNTING
Note
: Before permanently mounting, ensure that the indoor weather station is able to receive signals from the transmitters and WWVB signal at the desired location. T o achieve a true temperature reading, avoid mounting the remote thermo/hygro sensor (or any sensor) where direct sunlight can reach the remote sensor. We recommend that you mount the remote sensor on a North-facing wall or under an eve. The sending range of the remote thermo/hygro sensor is 80-ft (25m) however obstacles such as walls, concrete, and large metal objects can reduce the range. Place all units in their desired location, and wait approximately 15 minutes before permanently mounting to ensure that there is proper reception. If the indoor weather station loses the signal from the remote sensor, it will display the last temperature reading for 15 minutes. After 15 minutes of not receiving any signals, the remote temperature will display "- -.-".
A. Mounting the Remote Thermo/hygro Sensor
The remote thermo/hygro sensor can be mounted with the use of screws or by using the adhesive tape.
GB
P.16
P.17
GB
Loading...
+ 23 hidden pages