Karcher T-RACER, T 200 User Manual
T-Racer
T 200
English 3
Español 6
Français 9
59637490 04/10
2
Safety instructions Preparing the Appliance
WARNING
When using this product basic precautions should always be followed, including the following:
Read all the instructions before using
the product.
Please observe the safety instruc-
tions of your pressure washer.
The T-Racer must not be used by
children.
Only trigger the gun of the pressure
washer if the T-Racer is located on
the surface to be cleaned.
Keep all persons/animals clear of
the immediate vicinity of the cleaning
head.
Beware of the recoil force! Ensure a
stable position and firmly hold the
trigger gun with the extension handle.
Turn off the pressure washer when
examing or changing the T-Racer
and after the completion of the cleaning operation.
Maximum water temperature al-
lowed is 140 °F (60°C). Please follow
the instructions of your pressure
washer.
몇 Caution
Do not use on windows.
The T-Racer is not suited for scour-
ing or scrubbing.
Do not run over freestanding cor-
ners.
Always test the T–Racer in an incon-
spicuous area.
Never operate in the same area for
more than 2 seconds, damage may
occur.
Description of the Appliance
When unpacking the product, make
sure that no accessories are missing
and that none of the package contents
have been damaged. If you detect any
transport damages please contact your
retailer.
Illustrations on Page 2
Illustration
1 Housing
2 Bayonet connection with union nut
3 Handle
4 Rotating nozzle holder
5 High pressure nozzle
6 Lower wand
7 Upper wand
Intended use
For pressure washers with a
pressure from 1400 psi to 1650 psi
Use on horizontal surfaces like driveways, patios, side walks, etc.
Use on vertical surfaces like brick walls,
hardiplank, stucco and other siding.
The T-Racer has not been designed for
commercial use.
Symbols on the appliance
Danger!
Keep hands away from moving
parts.
SAVE THESE INSTRUCTIONS!
English 3
Application
Cleaning vertical surfaces
Note: Always use Kärcher water filter
(order no. 4.730-059.0) during suction
operations of the pressure washer.
Cleaning horizontal surfaces
Note: Outdoor surfaces should be
swept before the T-Racer is used to
avoid damaging the nozzles.
Connect the T-Racer and both wands
with the trigger gun.
Illustration
Î Connect lower wand with T-Racer.
1 Press the bayonett connection into
the bayonet catch, then turn by 90°
until it locks into place.
2 Tighten the union nut.
Î Connect upper wand with lower
wand.
1 Press the bayonett connection into
the bayonet catch, then turn by 90°
until it locks into place.
2 Tighten the union nut.
Î Connect trigger gun with upper
wand.
1 Press the bayonett connection into
the bayonet catch, then turn by 90°
until it locks into place.
2 Tighten the union nut.
Connect the T-Racer and the lower
wand with the trigger gun.
Illustration
Î Connect lower wand with T-Racer.
1 Press the bayonett connection into
the bayonet catch, then turn by 90°
until it locks into place.
2 Tighten the union nut.
Î Connect trigger gun with lower wand.
1 Press the bayonett connection into
the bayonet catch, then turn by 90°
until it locks into place.
2 Tighten the union nut.
Caution
Always hold the T-Racer at the hand
grip while cleaning the walls.
Do not reach under the edge of the
T-Racer while the device is in operation.
Illustration
몇 Caution
Do not run over freestanding corners.
4 English
Loading...