Kyocera 9130DN - B/W Laser, FS-9130DN, FS-9530DN Printer Operation Manual

Operation Guide

FS-9130DN
FS-9530DN

OPERATION GUIDE i

Contents

1 Machine Parts. ... ... ... .... ............................................. ... ... .............................................. ..............1-1

Components at the Front of the Printer .......................................................................................1-2

Components at the Left and the Rear of the Printer ...................................................................1-3

Components at the Right of the Printer .......................................................................................1-4

2 Printing Operation......................................................................................................................2-1

Loading Printer Driver .................................................................................................................2-2

Printing from Application Software ..............................................................................................2-3

3 Maintenance ...............................................................................................................................3-1

General Information ........................................................ .... ... .....................................................3-2

Toner Container Replacement ....................................................................................................3-3

Cleaning the Printer ....................................................................................................................3-9

4 Troubleshooting.........................................................................................................................4-1

General Guideline ........................................ ... ... .............................................. ... ........................4-2

Print Quality Problems .................................................... .... ... ... ... .... ...........................................4-4

Indicators and Messages ............................................................................................................4-7

Correcting a Paper Jam ............................................................................................................4-14

5 Specifications.............................................................................................................................5-1

ii OPERATION GUIDE

OPERATION GUIDE iii

Legal and Safety Information

CAUTION: NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED

BY IMPROPER INSTALLATION.

Notice on Software

SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE
PRINTER'S EMULATION MODE. The printer is factory-set to emulate the
PCL. The emulation mode can be changed.

Notice

The information in this guide is subject to change without notification.
Additional pages may be inserted in future editions. The user is asked to
excuse any technical inaccuracies or typographical errors in the present
edition.

No responsibility is assumed if accidents occur while the user is following
the instructions in this guide. No responsibility is assumed for defects in the
printer's firmware (contents of its read-only memory).

This guide, any copyrightable subject matter sold or provided with or in
connection with the sale of the page printer, are protected by copyright. All
rights are reserved. Copying or other reproduction of all or part of this
guide, any copyrightable subject matter without the prior written consent of
Kyocera Mita Corporation is prohibited. Any copies made of all or part of
this guide, any copyrightable subject must contain the same copyright
notice as the material from which the copying is done.

Regarding Tradenames

PRESCRIBE is a registered trademark of Kyocera Corporation. KPDL and
KIR (Kyocera Image Refinement) are trademarks of Kyocera Corporation.

Hewlett-Packard, PCL, and PJL are registered trademarks of Hewlett­Packard Company. Centronics is a trade name of Centronics Data
Computer Inc. PostScript is a registered trademark of Adobe Systems
Incorporated. Macintosh is a registered trademark of Apple Computer, Inc.
Microsoft, Windows, and Windows NT are registered trademarks of
Microsoft Corporation. Microsoft Windows Server is a trademark of
Microsoft Corporation. PowerPC is a trademark of International Business
Machines Corporation. Microdrive is a registered trademark of Hitachi
Global Storage Technologies Netherlands B.V. in the US and other
countries. CompactFlash is a trademark of SanDisk Corporation.
ENERGY STAR is a U.S. registered mark. All other brand and product
names are registered trademarks or trademarks of their respective
companies.

iv OPERATION GUIDE

This product uses PeerlessPrintXL to provide the HP LaserJet compatible
PCL 6 language emulation. PeerlessPrintXL is a trademark of Peerless
Systems Corporation, 2381 Rosecrans Ave. El Segundo, CA 90245,
U.S.A.

This product was developed using the Tornado™ Real Time Operating
System and Tools from Wind River Systems.

This product contains UFST™ and MicroType® from Monotype Imaging
Inc.

USB

This product has been certified by the USB Implementers Forum, Inc.

OPERATION GUIDE v

License Agreements

IBM Program License Agreement

THE DEVICE YOU HAVE PURCHASED CONTAINS ONE OR MORE
SOFTWARE PROGRAMS (“PROGRAMS”) WHICH BELONG TO
INTERNATIONAL BUSINESS MACHINES CORPORATION (“IBM”). THIS
DOCUMENT DEFINES THE TERMS AND CONDITIONS UNDER WHICH
THE SOFTWARE IS BEING LICENSED TO YOU BY IBM. IF YOU DO
NOT AGREE WITH THE TERMS AND CONDITIONS OF THIS LICENSE,
THEN WITHIN 14 DAYS AFTER YOUR ACQUISITION OF THE DEVICE
YOU MAY RETURN THE DEVICE FOR A FULL REFUND. IF YOU DO
NOT SO RETURN THE DEVICE WITHIN THE 14 DAYS, THEN YOU
WILL BE ASSUMED TO HAVE AGREED TO THESE TERMS AND
CONDITIONS.

The Programs are licensed not sold. IBM, or the applicable IBM country
organization, grants you a license for the Programs only in the country
where you acquired the Programs. You obtain no rights other than those
granted you under this license.

The term “Programs” means the original and all whole or partial copies of
it, including modified copies or portions merged into other programs. IBM
retains title to the Programs. IBM owns, or has licensed from the owner,
copyrights in the Programs.

1. License

Under this license, you may use the Programs only with the device on
which they are installed and transfer possession of the Programs and the
device to another party.

If you transfer the Programs, you must transfer a copy of this license and
any other documentation to the other party. Your license is then
terminated. The other party agrees to these terms and conditions by its first
use of the Program.

You may not:

1 use, copy, modify, merge, or transfer copies of the Program except

as provided in this license;

2 reverse assemble or reverse compile the Program; or

3 sublicense, rent, lease, or assign the Program.

2. Limited Warranty

The Programs are provided “AS IS.”

THERE ARE NO OTHER WARRANTIES COVERING THE PROGRAMS
(OR CONDITIONS), EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.

vi OPERATION GUIDE

Some jurisdictions do not allow the exclusion of implied warranties, so the
above exclusion may not apply to you.

3. Limitation of Remedies

IBM's entire liability under this license is the following;

For any claim (including fundamental breach), in any form, related in any
way to this license, IBM's liability will be for actual damages only and will
be limited to the greater of:

1 the equivalent of U.S. $25,000 in your local currency; or

2 IBM's then generally available license fee for the Program

This limitation will not apply to claims for bodily injury or damages to real
or tangible personal property for which IBM is legally liable.

IBM will not be liable for any lost profits, lost savings, or any incidental
damages or other economic consequential damages, even if IBM, or its
authorized supplier, has been advised of the possibility of such damages.
IBM will not be liable for any damages claimed by you based on any third
party claim. This limitation of remedies also applies to any developer of
Programs supplied to IBM. IBM's and the developer's limitations of
remedies are not cumulative. Such developer is an intended beneficiary of
this Section. Some jurisdictions do not allow these limitations or
exclusions, so they may not apply to you.

4. General

You may terminate your license at any time. IBM may terminate your
license if you fail to comply with the terms and conditions of this license. In
either event, you must destroy all your copies of the Program. You are
responsible for payment of any taxes, including personal property taxes,
resulting from this license. Neither party may bring an action, regardless of
form, more than two years after the cause of action arose. If you acquired
the Program in the United States, this license is governed by the laws of
the State of New York. If you acquired the Program in Canada, this license
is governed by the laws of the Province of Ontario. Otherwise, this license
is governed by the laws of the country in which you acquired the Program.

OPERATION GUIDE vii

Typeface Trademark Acknowledgement

All resident fonts in this printer are licensed from Monotype Imaging Inc.

Helvetica, Palatino and Times are registered trademarks of Linotype-Hell
AG. ITC Avant Garde Gothic, ITC Bookman, ITC ZapfChancery and ITC
Zapf Dingbats are registered trademarks of International Typeface
Corporation.

Monotype Imaging License Agreement

1 “Software” shall mean the digitally encoded, machine readable,

scalable outline data as encoded in a special format as well as the
UFST Software.

2 You agree to accept a non-exclusive license to use the Software to

reproduce and display weights, styles and versions of letters,
numerals, characters and symbols (“Typefaces”) solely for your own
customary business or personal purposes at the address stated on
the registration card you return to Monotype Imaging. Under the
terms of this License Agreement, you have the right to use the Fonts
on up to three printers. If you need to have access to the fonts on
more than three printers, you need to acquire a multi-user license
agreement which can be obtained from Monotype Imaging.
Monotype Imaging retains all rights, title and interest to the Software
and Typefaces and no rights are granted to you other than a License
to use the Software on the terms expressly set forth in this
Agreement.

3 To protect proprietary rights of Monotype Imaging, you agree to

maintain the Software and other proprietary information concerning
the Typefaces in strict confidence and to establish reasonable
procedures regulating access to and use of the Software and
Typefaces.

4 You agree not to duplicate or copy the Software or Typefaces, except

that you may make one backup copy. You agree that any such copy
shall contain the same proprietary notices as those appearing on the
original.

5 This License shall continue until the last use of the Software and

Typefaces, unless sooner terminated. This License may be
terminated by Monotype Imaging if you fail to comply with the terms
of this License and such failure is not remedied within thirty (30) days
after notice from Monotype Imaging. When this License expires or is
terminated, you shall either return to Monotype Imaging or destroy all
copies of the Software and Typefaces and documentation as
requested.

6 You agree that you will not modify, alter, disassemble, decrypt,

reverse engineer or decompile the Software.

7 Monotype Imaging warrants that for ninety (90) days after delivery,

the Software will perform in accordance with Monotype Imaging­published specifications, and the diskette will be free from defects in
material and workmanship. Monotype Imaging does not warrant that
the Software is free from all bugs, errors and omissions.

viii OPERATION GUIDE

8 THE PARTIES AGREE THAT ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF
FITNESS FOR A PARTICULAR PURPOSE AND
MERCHANTABILITY, ARE EXCLUDED.

9 Your exclusive remedy and the sole liability of Monotype Imaging in

connection with the Software and Typefaces is repair or replacement
of defective parts, upon their return to Monotype Imaging.

10 IN NO EVENT WILL MONOTYPE IMAGING BE LIABLE FOR LOST

PROFITS, LOST DATA, OR ANY OTHER INCIDENTAL OR
CONSEQUENTIAL DAMAGES, OR ANY DAMAGES CAUSED BY
ABUSE OR MISAPPLICATION OF THE SOFTWARE AND
TYPEFACES.

11 Massachusetts U.S.A. law governs this Agreement.

12 You shall not sublicense, sell, lease, or otherwise transfer the

Software and/or Typefaces without the prior written consent of
Monotype Imaging.

13 Use, duplication or disclosure by the Government is subject to

restrictions as set forth in the Rights in Technical Data and Computer
Software clause at FAR 252-227-7013, subdivision (b)(3)(ii) or
subparagraph (c)(1)(ii), as appropriate. Further use, duplication or
disclosure is subject to restrictions applicable to restricted rights
software as set forth in FAR 52.227-19 (c)(2).

14 YOU ACKNOWLEDGE THAT YOU HAVE READ THIS

AGREEMENT, UNDERSTAND IT, AND AGREE TO BE BOUND BY
ITS TERMS AND CONDITIONS. NEITHER PARTY SHALL BE
BOUND BY ANY STATEMENT OR REPRESENTATION NOT
CONTAINED IN THIS AGREEMENT. NO CHANGE IN THIS
AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED
BY PROPERLY AUTHORIZED REPRESENTATIVES OF EACH
PARTY. BY OPENING THIS DISKETTE PACKAGE, YOU AGREE
TO ACCEPT THE TERMS AND CONDITIONS OF THIS
AGREEMENT.

Compliance and Conformity

FCC Statement (for users in the United States)

This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.

Operation is subject to the following two conditions; (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.

This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no

OPERATION GUIDE ix

guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that
used for the receiver.

• Consult your service technician or an experienced radio/TV technician
for help.

Changes or modifications not expressly approved by the manufacturer for
compliance could void the user's authority to operate the equipment.
Shielded circular cables should be used for interfacing with the computer.

Precautions for Use

Any modifications without prior permission of Kyocera may cause harmful
interference.

If any modifications or changes are made to this equipment without prior
permission of Kyocera, Kyocera as the manufacturer does not guarantee
the compliance with the FCC Rules. The use of equipment that does not
comply with the FCC Rules is prohibited.

x OPERATION GUIDE

Safety Information

Laser Safety

This printer is certified as a Class 1 laser product under the U.S.
Department of Health and Human Services (DHHS) Radiation
Performance Standard according to Radiation Control for Health and
Safety Act of 1968. This means that the printer does not produce
hazardous laser radiation. Since radiation emitted inside the printer is
completely confined within protective housings and external covers, the
laser beam cannot escape from the printer during any phase of user
operation.

Laser Notice

This printer is certified in the U.S. to conform to the requirements of DHHS
21 CFR Subchapter for Class I (1) laser products, and elsewhere is
certified as a Class I laser product conforming to the requirements of IEC

825.

DANGER:CLASS 3B LASER RADIATION WHEN OPEN. AVOID

DIRECT EXPOSURE TO BEAM.

CAUTION: Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous radiation
exposure.

Radio Frequency Transmitter

This machine contains the transmitter module. We, the manufacturer
(Kyocera Corporation) hereby declare that this equipment (page printer),
model FS-9130DN and FS-9530DN are in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.

Radio Tag Technology

In some countries the radio tag technology used in this equipment to
identify the toner container may be subject to authorization and the use of
this equipment may consequently be restricted.

OPERATION GUIDE xi

Caution Labels

Caution labels have been attached to the copier at the following locations
for safety purposes. Be sufficiently careful to avoid fire or electric shock
when removing a paper jam or when replacing toner.

NOTE: Do not remove these labels.

High temperature inside. Do not
touch parts in this area, because
there is a danger of getting burned.

Do not incinerate toner and toner
container. Dangerous sparks may
cause burn.

Moving parts inside. May cause
personal injury. Do not touch
moving parts.

High temperature inside. Do not
touch parts in this area, because
there is a danger of getting burned.

Label inside the printer (Laser
radiation warning)

For U.S.A.
and Canada

For Europe, Asia,
and other countries

xii OPERATION GUIDE

CDRH Regulations

The Center for Devices and Radiological Health (CDRH) of the U.S. Food
and Drug Administration implemented regulations for laser products on
August 2, 1976. These regulations apply to laser products manufactured
after August 1, 1976. Compliance is mandatory for products marketed in
the United States. A label indicating compliance with the CDRH regulations
must be attached to laser products marketed in the United States. On this
machine, the label is on the right.

Ozone Concentration

The printers generate ozone gas (O3) which may concentrate in the place
of installation and cause an unpleasant smell. To minimize the

concentration of ozone gas to less than 0.1ppm, we recommend you not
to install the printer in a confined area where ventilation is blocked.

Declaration of Conformity for U.S.A.

Model name: Page Printer FS-9130DN/FS-9530DN
Trade name: Kyocera Mita
Responsible party: Kyocera Mita America, Inc.
Address: 225 Sand Road PO Box 40008 Fairfield, New Jersey 07004­0008, U.S.A.
Telephone: [phone]
Fax: [phone]

Manufacturer: Kyocera Mita Corporation
Manufacturer's address: 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka,
540-8585, Japan

This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

OPERATION GUIDE xiii

The manufacturer and its merchandising companies retain the following
technical documentation in anticipation of the inspection that may be
conducted by the authorities concerned.

User’s instruction that conforms to the applicable specifications.
Technical drawings.
Descriptions of the procedures that guarantee the conformity.
Other technical information.

Kyocera Mita America Inc.

CE Marking Directive

According to Council Directive 89/336/EEC, 73/23/EEC, and 1999/5/EC

Manufacturer: Kyocera Mita Corporation
Manufacturer's address: 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka,
540-8585, Japan

Declares that the product

Product name: Page Printer

Model number: FS-9130DN/FS-9530DN (as tested with enhancement
optional unit; Dual Paper Feeder PF-700, Large Capacity Paper Feeder
PF-750, Document Finisher DF-710/DF-730, Booklet Unit BF-710, Mail
Bin MT-710, and Punch Unit PH-5A)

Conforms to the following product specifications:

EN 55 022:1998+A1:2000+A2:2003 Class B
EN 61 000-3-2:2000
EN 61 000-3-3:1995+A1:2001
EN 55 024:1998+A1:2001+A2:2003
EN 60 950-1:2001+A11
EN 60 825-1:1994+A1+A2
EN 300330-1
EN 300330-2

The manufacturer and its merchandising companies retain the following
technical documentation in anticipation of the inspection that may be
conducted by the authorities concerned.

User’s instruction that conforms to the applicable specifications.
Technical drawings.
Descriptions of procedures that guarantee conformity.
Other technical information.

xiv OPERATION GUIDE

Declaration of Conformity (Australia)

Manufacturer: Kyocera Mita Corporation
Manufacturer's address: 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka,
540-8585, Japan

declares that the product

Product name: Page Printer
Model name: FS-9130DN/FS-9530DN

Description of devices: This Page Printer Model FS-9530DN is the 51ppm
(FS-9130DN is the 40ppm); A4 size and utilized plain paper; dry toner; etc.
The printer can be equipped with several enhancement optional unit as a
dual paper feeder as PF-700, large capacity paper feeder as PF-750, DF­710/DF-730 as document finisher, booklet unit as BF-710m mail bin as
MT-710, and punch unit as PH-5A.

conforms to the following product specifications:

AS/NZS 3548: 1995 (EN 55 022: 1998 Class B)
AS/NZS 4268: 2003
IEC60950: 1999 (EN 60 950: 2000)

The manufacturer and its merchandising companies retain the following
technical documentation in anticipation of the inspection that may be
conducted by the authorities concerned.

User’s instruction that conforms to the applicable specifications
Technical drawings
Descriptions of procedures that guarantee conformity
Other technical information

The manufacturer has been employed with ISO9001 scheme. JQA and BS
have attested the manufacturer.

Kyocera Mita Australia Pty., Ltd.
6-10 Talavera Road, North Ryde, NSW 2113, Australia
Telephone: [phone]
Fax: [phone]

Canadian Department of Communications Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.

Avis de conformité aux normes du ministere des Communications du
Canada

Cet appareil numérique de la classe B est conforme a la norme NMB-003
du Canada.

OPERATION GUIDE xv

EN ISO 7779

Maschinenlärminformations-Verordnung 3. GPSGV, der höchste
Schalldruckpegel beträgt 70 dB (A) oder weniger gemäß EN ISO 7779.

Disclaimer

Kyocera Mita will not be liable to customers or any other person or entity
for any loss or damage caused or alleged to be caused directly or indirectly
by equipment sold or furnished by us, including but not limited to, any
interruption of service, loss of business or anticipatory profits, or
consequential damages resulting from the use or operation of the
equipment or software.

Energy Star Program

As an ENERGY STAR Partner, we have determined that this product meets
the ENERGY STAR guidelines for energy efficiency.

The basic objective of the ENERGY STAR Program is to reduce environmental
pollution by encouraging the manufacture and sale of equipment that uses
energy more efficiently.

This printer is equipped with a sleep timer function that conforms with the
standards of the E

NERGY STAR Program. This function makes it possible to

reduce the amount of electrical power consumed by the printer. For
maximum power savings, turn off the printer’s power supply when not
using the printer for extended periods of time.

For details on the sleep timer function and printer power consumption,
refer to this manual.

Initial settings of the sleep timer function and power saved using the sleep
timer function:

FS-9130DN FS-9530DN

Initial Auto Sleep
Setting

15 minutes (60 minutes) 15 minutes (60 minutes)

Power
Consumption in
Auto Sleep

4.5W (40W) 4.5W (75W)

( ): ENERGY STAR program guideline

xvi OPERATION GUIDE

Please read this Operation Guide before using the machine. Keep it close
to the machine for easy reference.

The sections of this guide and parts of the machine marked with symbols
are safety warnings meant to protect the user, other individuals and
surrounding objects, and ensure correct and safe usage of the machine.
The symbols and their meanings are indicated below.

DANGER: Indicates that serious injury or even death will
very possibly result from insufficient attention to or incorrect
compliance with the related points.

WARNING: Indicates that serious injury or even death may
result from insufficient attention to or incorrect compliance
with the related points.

CAUTION: Indicates that personal injury or mechanical
damage may result from insufficient attention to or incorrect
compliance with the related points.

OPERATION GUIDE xvii

Symbols

The following symbols indicate that the related section includes safety
warnings. Specific points of attention are indicated inside the symbol.

.... [General warning]

.... [Warning of danger of electrical shock]

.... [Warning of high temperature]

The following symbols indicate that the related section includes
information on prohibited actions. Specifics of the prohibited action are
indicated inside the symbol.

.... [Warning of prohibited action]

.... [Disassembly prohibited]

The following symbols indicate that the related section includes
information on actions which must be performed. Specifics of the required
action are indicated inside the symbol.

.... [Alert of required action]

.... [Remove the power plug from the outlet]

....

[Always connect the machine to an outlet with a ground
connection]

Please contact your service representative to order a replacement if the
safety warnings in this Operation Guide are illegible or if the guide itself is
missing. (fee required)

xviii OPERATION GUIDE

Installation Precautions

Environment

CAUTION:

Avoid placing the machine on or in locations which are unstable
or not level. Such locations may cause the machine to fall down
or fall over. This type of situation presents a danger of personal
injury or damage to the machine.

Avoid locations with humidity or dust and dirt. If dust or dirt
become attached to the power plug, clean the plug to avoid the
danger of fire or electrical shock.

Avoid locations near radiators, heaters, or other heat sources, or
locations near flammable items, to avoid the danger of fire.

To keep the machine cool and facilitate changing of parts and
maintenance, allow access space as shown below. Leave
adequate space, especially around the vents, to allow air to be
properly ventilated out of the

printer.

Left: 300 mm

(12 inches)

Right: 300 mm

(12 inches)

Rear: 100 mm

(4 inches)

Front: 1,000 mm

(40 inches)

Always use the caster stoppers to stabilize the printer once it is
in place to keep it from moving and/or falling over and causing
injury.

Other Precautions

Adverse environmental conditions may affect the safe operation and
performance of the machine. Install in an air-conditioned room
(recommended room temperature: around 23°C, humidity: around 60%
RH), and avoid the following locations when selecting a site for the
machine.

OPERATION GUIDE xix

• Avoid locations near a window or with exposure to direct sunlight.

• Avoid locations with vibrations.

• Avoid locations with drastic temperature fluctuations.

• Avoid locations with direct exposure to hot or cold air.

• Avoid poorly ventilated locations.

• When casters are installed on the printer, moving the printer can

cause damage to certain floor surfaces.

During printing, some ozone is released, but the amount does not cause
any ill effect to one's health. If, however, the printer is used over a long
period of time in a poorly ventilated room or when printing an extremely
large number of copies, the smell may become unpleasant. To maintain
the appropriate environment for print work, it is suggested that the room be
properly ventilated.

Power Supply/Grounding the Machine

WARNING:

Do not use a power supply with a voltage other than that
specified. Avoid multiple connections in the same outlet. These
types of situations present a danger of fire or electrical shock.

Plug the power cord securely into the outlet. If metallic objects
come in contact with the prongs on the plug, it may cause a fire
or electric shock.

Always connect the machine to an outlet with a ground
connection to avoid the danger of fire or electrical shock in case
of an electric short. If an earth connection is not possible, contact
your service representative.

Other Precautions

Connect the power plug to the closest outlet possible to the machine.

The power supply cord is used as the main disconnect device. Ensure that
the socket/outlet is located/installed near the equipment and is easily
accessible.

xx OPERATION GUIDE

Handling of Plastic Bags

WARNING:

Keep the plastic bags that are used with the machine away from
children. The plastic may cling to their nose and mouth causing
suffocation.

OPERATION GUIDE xxi

Precautions for Use

Cautions when Using the Machine

WARNING:

Do not place metallic objects or containers with water (flower
vases, flower pots, cups, etc.) on or near the machine. This
situation presents a danger of fire or electrical shock should they
fall inside.

Do not remove any of the covers from the machine as there is a
danger of electrical shock from high voltage parts inside the
machine.

Do not damage, break or attempt to repair the power cord. Do not
place heavy objects on the cord, pull it, bend it unnecessarily or
cause any other type of damage.
These types of situations present a danger of fire or electrical
shock.

Never attempt to repair or disassemble the machine or its parts
as there is a danger of fire, electrical shock or damage to the
laser. If the laser beam escapes, there is a danger of it causing
blindness.

If the machine becomes excessively hot, smoke appears from
the machine, there is an odd smell, or any other abnormal
situation occurs, there is a danger of fire or electrical shock. Turn
the power switch off (O) immediately, be absolutely certain to
remove the power plug from the outlet and then contact your
service representative.

If anything harmful (paper clips, water, other fluids, etc.) falls into
the machine, turn the power switch off (O) immediately. Next, be
absolutely certain to remove the power plug from the outlet to
avoid the danger of fire or electrical shock. Then contact your
service representative.

Do not remove or connect the power plug with wet hands, as
there is a danger of electrical shock.

Always contact your service representative for maintenance or
repair of internal parts.

xxii OPERATION GUIDE

CAUTION

Do not pull the power cord when removing it from the outlet. If the power
cord is pulled, the wires may become broken and there is a danger of fire
or electrical shock. (Always grasp the power plug when removing the
power cord from the outlet.)

Always remove the power plug from the outlet when moving the
machine. If the power cord is damaged, there is a danger of fire
or electrical shock.

If the machine will not be used for a short period of time
(overnight, etc.), turn the power switch off (O). If it will not be
used for an extended period of time (vacations, etc.), remove the
power plug from the outlet for safety purposes during the time the
machine is not in use.

When lifting or moving the printer, pull up the 4 handles on both
sides of the printer, then ALWAYS carry the printer by the
designated 4 handles with at least 4 people, one person to a
handle.

For safety purposes, always remove the power plug from the
outlet when performing cleaning operations.

If dust accumulates within the machine, there is a danger of fire
or other trouble. It is therefore recommended that you consult
with your service representative in regard to cleaning of internal
parts. This is particularly effective if accomplished prior to
seasons of high humidity. Consult with your service
representative in regard to the cost of cleaning the internal parts of the
machine.