How it Works
KTM
Loading...
EXC-F Six Days 2010
Owner's manual
125 pgs3.66 Mb0
Table of contents
Loading...

KTM 250 EXC EU-AUS 2010, EXC-F Six Days 2010, 250 XCF-W 2010, 250 SX-F 2010 Owner's manual

OWNER'S MANUAL 2010
250 EXC-F EU
250 EXC-F AUS
250 EXC-F SIX DAYS EU
250 XCF-W ZA
250 SX-F EU
250 SX-F USA
Art. no. 3211465en
DEARKTM CUSTOMER
Congratulations on your decision to purchase a KTM motorcycle. You are now the owner of a state-of-the-art sports motorcycle that will give you enormous pleasure if you service and maintain it accordingly.
We wish you a lot of enjoyment riding this vehicle!
Enter the serial numbers of your vehicle below.
Chassis number ( p. 10) Dealer's stamp
Engine number ( p. 10)
Key number (EXC-F, EXC‑F SIX DAYS) ( p. 10)
The owner's manual corresponded to the latest state of this series at the time of printing. Slight deviations resulting from continuing development and design of our motorcycles can however not be completely excluded.
All specifications are non-binding. KTM Sportmotorcycle AG specifically reserves the right to modify or delete technical specifica­tions, prices, colors, forms, materials, services, designs, equipment, etc., without prior notice and without specifying reasons, to adapt these to local conditions, as well as to stop production of a particular model without prior notice. KTM accepts no liability for delivery options, deviations from illustrations and descriptions, as well as misprints and other errors. The models portrayed partly contain spe­cial equipment that does not belong to the regular scope of delivery.
© 2009 by KTM-Sportmotorcycle AG, Mattighofen Austria All rights reserved Reproduction, even in part, is permitted only with the express written permission of the copyright owner.
ISO 9001(12 100 6061) According to the international quality management standard ISO 9001, KTM uses quality assurance processes that lead to the maximum possible quality of the products. Issued by: TÜV Management Service
KTM-Sportmotorcycle AG 5230 Mattighofen, Austria
TABLEOF CONTENTS
MEANS OF REPRESENTATION ............................................ 5
IMPORTANT INFORMATION ................................................ 6
VIEW OF VEHICLE............................................................... 8
View of the vehicle from the left front (example) ................. 8
View of the vehicle from the right rear (example) ................ 9
LOCATION OF SERIAL NUMBERS ...................................... 10
Chassis number............................................................. 10
Type label..................................................................... 10
Key number (EXC-F, EXC‑F SIX DAYS)............................. 10
Engine number.............................................................. 10
Fork part number........................................................... 10
Shock absorber part number ........................................... 11
CONTROLS....................................................................... 12
Clutch lever .................................................................. 12
Hand brake lever ........................................................... 12
Short circuit button (XCF‑W, SX‑F) .................................. 12
Short circuit button (EXC-F, EXC‑F SIX DAYS).................. 12
Emergency OFF switch (EXC‑F AUS) ............................... 12
Electric starter button (EXC‑F EU, EXC‑F SIX DAYS,
XCF‑W)......................................................................... 13
Electric starter button (EXC‑F AUS)................................. 13
Light switch (EXC-F, EXC‑F SIX DAYS) ............................ 13
Horn button (EXC-F, EXC‑F SIX DAYS)............................. 13
Turn signal switch (EXC-F, EXC‑F SIX DAYS).................... 13
Overview of indicator lamps (EXC-F, EXC‑F SIX DAYS) ...... 14
CONTROLS (EXC‑F, EXC‑F SIX DAYS, XCF-W) ...................... 15
Speedometer................................................................. 15
Speedometer activation and test ..................................... 15
Tripmaster switch .......................................................... 15
Setting kilometers or miles ............................................. 15
Setting the clock ........................................................... 16
Adjusting the speedometer functions............................... 16
Querying the lap time .................................................... 17
SPEED display mode (speed).......................................... 17
Display mode SPEED/H (service hours) ............................ 17
Display mode SPEED/CLK (clock) ................................... 18
Display mode SPEED/LAP (lap time) ............................... 18
Display mode SPEED/ODO (odometer) ............................. 18
Display mode SPEED/TR1 (trip master 1) ........................ 18
Display mode SPEED/TR2 (trip master 2) ........................ 19
Disply mode SPEED/A1 (average speed 1) ....................... 19
Display mode SPEED/A2 (average speed 2)...................... 19
Display mode SPEED/S1 (stop watch 1) .......................... 20
Display mode SPEED/S2 (stop watch 2) .......................... 20
CONTROLS....................................................................... 22
Fuel tap (EXC‑F, EXC‑F SIX DAYS, XCF-W)....................... 22
Fuel tap (SX‑F).............................................................. 22
Opening filler cap.......................................................... 22
Closing filler cap ........................................................... 23
Choke (EXC-F EU, EXC‑F SIX DAYS)................................ 23
Choke (XCF‑W, SX‑F, EXC‑F AUS) ................................... 23
Shift lever..................................................................... 23
Foot brake lever............................................................. 24
Kick starter................................................................... 24
Side stand (EXC‑F, EXC‑F SIX DAYS, XCF-W) ................... 24
Plug-in stand (SX‑F) ...................................................... 24
Steering lock (EXC-F, EXC‑F SIX DAYS) ........................... 25
Locking the steering (EXC-F, EXC‑F SIX DAYS)................. 25
Unlocking the steering (EXC-F, EXC‑F SIX DAYS).............. 25
GENERAL TIPS AND HINTS ON PUTTING INTO
OPERATION...................................................................... 26
Advice on first use ......................................................... 26
Running-in the engine ................................................... 27
Preparing vehicle for arduous riding conditions................. 27
Preparing for riding on dry sand ...................................... 27
Preparing for riding on wet sand...................................... 28
Preparing for riding on wet and muddy surfaces................ 29
Preparing for rides at high temperature and slow speed ..... 30
Preparing for rides at low temperatures or in snow ............ 30
RIDING INSTRUCTIONS .................................................... 31
Checks before putting into operation ............................... 31
Starting ........................................................................ 31
Starting up ................................................................... 32
Shifting, riding.............................................................. 32
Braking ........................................................................ 32
Stopping, parking .......................................................... 33
Refueling...................................................................... 33
SERVICE SCHEDULE (EXC‑F, EXC‑F SIX DAYS, XCF-W)........ 35
Important maintenance work to be carried out by an
authorized KTM workshop .............................................. 35
Important maintenance work to be carried out by an
authorized KTM workshop (as additional order)................. 36
SERVICE SCHEDULE (SX‑F)............................................... 37
Important maintenance work to be carried out by an
authorized KTM workshop .............................................. 37
Important maintenance work to be carried out by an
authorized KTM workshop (as additional order)................. 38
SERVICE SCHEDULE FOR RIDER....................................... 39
Important checks and maintenance work to be carried
out by the rider ............................................................. 39
MAINTENANCE WORK ON CHASSIS AND ENGINE .............. 40
Jacking up the motorcycle .............................................. 40
Removing the motorcycle from the work stand.................. 40
Checking the basic suspension setting with the rider's
weight .......................................................................... 40
Compression damping of shock absorber.......................... 40
Adjusting high-speed compression damping of the shock
absorber ....................................................................... 40
Adjusting the low-speed compression damping of the
shock absorber .............................................................. 41
Adjusting the rebound damping of the shock absorber....... 42
Measuring rear wheel sag unloaded ................................. 42
Checking the static sag of the shock absorber .................. 43
Checking the riding sag of the shock absorber .................. 43
Adjusting the spring preload of the shock absorber x ...... 43
Adjusting the riding sag x............................................. 44
Removing the shock absorber x..................................... 45
Installing the shock absorber x ..................................... 45
Checking basic setting of fork ......................................... 45
Adjusting the compression damping of the fork ................ 45
Adjusting the rebound damping of the fork....................... 46
Adjusting the spring preload of the fork (EXC‑F,
EXC‑F SIX DAYS, XCF-W) ............................................... 47
Bleeding fork legs.......................................................... 48
Cleaning the dust boots of the fork legs ........................... 48
Loosening the fork protector ........................................... 48
Positioning the fork protection ........................................ 48
Checking steering head bearing play................................ 49
Adjusting play of steering head bearing x (EXC‑F EU,
EXC‑F AUS, XCF‑W ZA) .................................................. 49
Adjusting the play of the steering head bearing x (SX‑F,
250 EXC-F SIX DAYS EU) .............................................. 50
Removing the fork legs................................................... 50
Installing the fork legs x............................................... 51
Removing the fork protector x....................................... 52
Installing the fork protector x ....................................... 52
Removing the front fender .............................................. 52
Installing the front fender............................................... 53
Removing headlight mask with headlight (EXC‑F,
EXC‑F SIX DAYS, XCF-W) ............................................... 53
Refitting the headlight mask with the headlight (EXC‑F,
EXC‑F SIX DAYS, XCF-W) ............................................... 53
Removing the start number plate (SX‑F) .......................... 54
Installing the start number plate (SX‑F) ........................... 54
Handlebar position ........................................................ 54
Adjusting handlebar position x...................................... 54
Checking throttle cable route .......................................... 55
Checking the play in the throttle cable............................. 55
Adjusting the play in the throttle cable x ....................... 56
Checking for chain dirt accumulation .............................. 56
Cleaning the chain......................................................... 56
Checking the chain tension ............................................ 57
Checking chain tension when fitting rear wheel ................ 57
Checking the rear sprocket/engine sprocket for wear ......... 57
Checking chain wear...................................................... 58
Adjusting chain tension.................................................. 58
Adjusting chain tension - after checking .......................... 59
Adjusting chain tension - fitting rear wheel ...................... 60
Adjusting the chain guide x (EXC‑F, EXC‑F SIX DAYS,
XCF-W)......................................................................... 60
Adjusting the chain guide x (SX‑F)................................ 61
Checking brake discs ..................................................... 61
Checking free travel of hand brake lever........................... 61
Adjusting basic position of hand brake lever (XCF‑W,
SX‑F)............................................................................ 62
Adjusting free travel of hand brake lever
(EXC-F, EXC‑F SIX DAYS)............................................... 62
Checking the brake fluid level of the front brake ............... 62
Topping up the front brake fluid x................................. 63
Checking the front brake linings...................................... 64
Changing the front brake linings x................................. 64
Checking free travel of foot brake lever ............................ 66
Adjusting basic position of footbrake lever x................... 66
Checking rear brake fluid level ........................................ 66
Adding brake fluid to the rear brake circuit x ................. 67
Checking rear brake linings ............................................ 67
Changing the rear brake linings x.................................. 68
Removing front wheel x................................................ 69
Installing the front wheel x........................................... 70
Removing the rear wheel x ........................................... 71
Installing the rear wheel x ............................................ 71
Tire condition checking.................................................. 72
Checking tire air pressure ............................................... 73
Checking spoke tension.................................................. 73
Removing the battery x (EXC‑F, EXC‑F SIX DAYS,
XCF-W)......................................................................... 74
Installing the battery x (EXC‑F, EXC‑F SIX DAYS,
XCF-W)......................................................................... 74
Recharging the battery x (EXC‑F, EXC‑F SIX DAYS,
XCF-W)......................................................................... 74
Removing a fuse (EXC‑F, EXC‑F SIX DAYS, XCF-W)........... 75
Replacing the fuse (EXC‑F, EXC‑F SIX DAYS, XCF-W) ....... 75
Adjusting the beam width of the headlight (EXC‑F,
EXC‑F SIX DAYS, XCF-W) ............................................... 76
Checking the headlight adjustment (EXC‑F,
EXC‑F SIX DAYS, XCF-W) ............................................... 76
Removing the seat ......................................................... 76
Mounting the seat ......................................................... 77
Dismounting the fuel tank x ......................................... 77
Installing the fuel tank x .............................................. 78
Cooling system .............................................................. 78
Checking the anti-freeze and coolant level ....................... 79
Checking the coolant level.............................................. 79
Draining the coolant x.................................................. 80
Refilling coolant x ....................................................... 80
Glass fiber yarn filling of main silencer ............................ 81
Removing main silencer ................................................. 81
Installing the main silencer ............................................ 81
Removing the air filter box lid......................................... 81
Installing the air filter box lid.......................................... 81
Removing the air filter x............................................... 82
Installing the air filter x ............................................... 82
Cleaning air filter x...................................................... 82
Adjusting basic position of clutch lever............................ 83
Checking the fluid level of hydraulic clutch...................... 83
Changing the hydraulic clutch fluid x ............................ 83
Checking the basic position of the shift lever.................... 84
Adjusting the basic position of the shift lever x .............. 84
Carburetor - idle ............................................................ 85
Carburetor - adjusting idle x ......................................... 85
Emptying the carburetor float chamber x ....................... 86
Checking the engine oil level .......................................... 87
Changing the engine oil and oil filter, cleaning the oil
screen x ..................................................................... 87
Draining the engine oil x .............................................. 87
Cleaning the oil screens x ............................................ 88
Removing the oil filter x............................................... 89
Installing the oil filter x ............................................... 89
Filling up with engine oil x........................................... 90
Adding engine oil .......................................................... 90
TROUBLESHOOTING......................................................... 91
CLEANING........................................................................ 93
Cleaning the motorcycle ................................................. 93
STORAGE ......................................................................... 94
Storage......................................................................... 94
Putting into operation after storage ................................. 94
TECHNICAL DATA - ENGINE .............................................. 95
Capacity - engine oil ...................................................... 96
Capacity - coolant.......................................................... 96
TECHNICAL DATA - ENGINE TIGHTENING TORQUES .......... 97
TECHNICAL DATA - CARBURETOR..................................... 99
EXC-F, EXC‑F SIX DAYS ................................................. 99
XCF-W.......................................................................... 99
SX‑F............................................................................. 99
TECHNICAL DATA - CHASSIS .......................................... 100
Lighting equipment ..................................................... 100
Tires .......................................................................... 101
Capacity - fuel............................................................. 101
TECHNICAL DATA - FORK................................................ 102
EXC‑F, EXC‑F SIX DAYS, XCF-W ................................... 102
SX‑F EU ..................................................................... 102
SX‑F USA ................................................................... 103
TECHNICAL DATA - SHOCK ABSORBER ........................... 104
EXC‑F, EXC‑F SIX DAYS, XCF-W ................................... 104
SX‑F........................................................................... 104
TECHNICAL DATA - TIGHTENING TORQUES FOR
CHASSIS ........................................................................ 105
WIRING DIAGRAM .......................................................... 106
Wiring diagram (EXC-F EU, EXC‑F SIX DAYS)................. 106
Wiring diagram (EXC‑F AUS) ........................................ 110
Wiring diagram (XCF-W) ............................................... 112
Wiring diagram (SX‑F).................................................. 114
SUBSTANCES................................................................. 116
AUXILIARY SUBSTANCES................................................ 117
STANDARDS................................................................... 119
INDEX ............................................................................ 120
Symbols used
The symbols used are explained in the following.
Indicates an expected reaction (e.g. of a work step or a function).
Indicates an unexpected reaction (e.g. of a work step or a function).
All work marked with this symbol requires specialist knowledge and technical understanding. In the interest of your own safety, have these jobs done in an authorized KTM workshop! There, your motorcycle will be serviced optimally by specially trained experts using the specialist tools required.
Identifies a page reference (more information is provided on the specified page).
Formats used
The typographical and other formats used are explained in the following.
Specific name Identifies a specific name.
®
Name
Brand™ Identifies a brand in merchandise traffic.
Identifies a protected name.
Use definition (EXC-F, EXC‑F SIX DAYS)
KTM sport motorcycles are designed and built to withstand the normal stresses and strains of competitive use. The motorcycles com­ply with currently valid regulations and categories of the top international motorsport organizations.
Info
The motorcycle is authorized for public road traffic in the homologous (reduced) version only. In the derestricted version, the motorcycle must be used only on closed off property remote from public road traffic. The motorcycle is designed for off-road sport endurance competition (Enduro) and not for the use predominantly in motocross.
Use definition (XCF‑W, SX‑F)
KTM sport motorcycles are designed and built to withstand the normal stresses and strains of competitive use. The motorcycles com­ply with currently valid regulations and categories of the top international motorsport organizations.
Info
The motorcycle must be used only on secluded property remote from public road traffic.
Maintenance
A prerequisite for trouble free operation and avoiding premature wear is that the engine and suspension are maintained and adjusted as described in this manual. Poor adjustment and tuning of the engine and suspension can lead to damage and breakage of compo­nents. Using a motorcycle in difficult conditions such as on sand or very wet and muddy ground can lead to excessive wear of components such as the power train or brakes. For this reason, it may be necessary to service or replace worn parts before the limit specified in the service schedule is reached. Pay careful attention to the prescribed running-in period, inspection and maintenance intervals. Observing these rules will vastly increase the service life of your motorcycle.
Warranty
The work prescribed in the service schedule must be carried out by an authorized KTM workshop only and confirmed in the customer's service record; otherwise, all warranty claims will be void. No warranty claim can be honored for damage resulting from manipulation and/or other changes to the vehicle.
Fuel, oils, etc.
You should use the fuels, oils and greases according to specifications as listed in the owner's manual.
Spare parts, accessories
For your own safety, only use spare parts and accessory products that have been approved and/or recommended by KTM and have them installed by an authorized KTM workshop. KTM accepts no liability for other products and any resulting damage or loss. Some spare parts and accessories are specified in brackets in the respective descriptions. Your KTM dealer will be happy to advise you.
You will find the current KTM PowerParts for your vehicle on the KTM website. International KTM Website: http://www.ktm.com
Work rules
Special tools are necessary for some of the work. These are not included with the vehicle and can be ordered under the number in parentheses. Ex: valve spring compressor (59029019000) During assembly, non-reusable parts (e.g. self-locking screws and nuts, seals and seal rings, O-rings, pins, lock washers) must be replaced by new parts. If thread lock (e.g. Loctite®) is used for screw connections, be sure to comply with the manufacturer's specific instructions on its usage. Parts that you want to reuse following repairs and servicing should be cleaned and checked for damage and wear. Change damaged or worn parts. Following repairs or servicing, the vehicle must be checked for roadworthiness.
Transport
Note
Danger of damage The parked vehicle can roll away or fall over.
– Always place the vehicle on a firm and even surface.
Note
Fire hazard Some vehicle components become very hot when the vehicle is operated.
– Do not park the vehicle near flammable or explosive substances. Do not place objects on the vehicle while it is still warm from
being run. Always let the vehicle cool first.
– Switch off the engine.
(EXC‑F, EXC‑F SIX DAYS, XCF-W)
– Turn handle of the fuel tap to the OFF position. (Figure 500137-10 p. 22)
(SX‑F)
– Turn handle of the fuel tap to the OFF position. (Figure 500178-10 p. 22)
– Use straps or other suitable devices to secure the motorcycle against accidents or falling over.
Environment
Motorcycling is a wonderful sport and we naturally hope that you can enjoy it to the full. However, it is a potential problem for the environment and can lead to conflicts with other persons. But if you use your motorcycle responsibly, you can ensure that such prob­lems and conflicts do not have to occur. To protect the future of motorcycle sport, make sure that you use your motorcycle legally, dis­play environmental consciousness, and respect the rights of others.
Notes/warnings
Pay close attention to the notes/warnings.
Info
Various information and warning labels are affixed to the vehicle. Do not remove information/warning labels. If they are miss­ing, you or others may not recognize potential hazards and may therefore be injured.
Grades of risks
Danger
Identifies a danger that will immediately and invariably lead to fatal or serious permanent injury if the appropriate measures are not taken.
Warning
Identifies a danger that is likely to lead to fatal or serious injury if the appropriate measures are not taken.
Note
Identifies a danger that will lead to considerable machine and material damage if the appropriate measures are not taken.
Warning
Identifies a danger that will lead to environmental damage if the appropriate measures are not taken.
Owner's manual
– It is important that you read this owner's manual carefully and completely before making your first trip. It contains useful infor-
mation and many tips on how to operate and handle your motorcycle. Only then will you find out how to best customize the motor­cycle for your own use and how you can protect yourself from injury. The owner's manual also contains important information on servicing the motorcycle.
– The owner's manual is an important component of the motorcycle and should be handed over to the new owner if the vehicle is
sold.

3.1View of the vehicle from the left front (example)

1 Hand brake lever 2 Filler cap 3 Clutch lever 4 Fuel tap 5 Shift lever 6 Air filter box lid 7 Chain guide
600874-10

3.2View of the vehicle from the right rear (example)

1 Rubber band for the side stand 2 Shock absorber, compression adjustment 3 Chassis number 4 Fork protector 5 Shock absorber, rebound adjustment 6 Level viewer, rear brake fluid 7 Level viewer, engine oil 8 Kickstarter
600873-10

LOCATION OF SERIAL NUMBERS 10

4.1Chassis number

The chassis number is stamped on the steering head on the right.
500127-10

4.2Type label

The type label is fixed to the front of the steering head.
500128-10

4.3Key number (EXC-F, EXC‑F SIX DAYS)

500125-10

4.4Engine number

The key number is stamped on the key strap.
The engine number is stamped on the left side of the engine under the engine sprocket.

4.5Fork part number

600661-12
The fork part number is stamped on the inner side of the fork stub.
500082-10
LOCATION OF SERIAL NUMBERS 11

4.6Shock absorber part number

The shock absorber part number is stamped on the top of the shock absorber above the adjusting ring on the engine side.
500129-10

CONTROLS 12

5.1Clutch lever

The clutch lever is fitted on the left side of the handlebar. The clutch is hydraulically operated and self-adjusting.
600659-10

5.2Hand brake lever

Hand brake lever is located on the right side of the handlebar. The hand brake lever is used to activate the front brake.
400196-10

5.3Short circuit button (XCF‑W, SX‑F)

The short circuit button is fitted on the left side of the handlebar.
Possible states
• Short circuit button in basic position – In this position, the ignition circuit is
• Short circuit button pressed – In this position, the ignition circuit is interrupted,
500132-10

5.4Short circuit button (EXC-F, EXC‑F SIX DAYS)

The short circuit button is fitted on the left side of the handlebar.
Possible states
• Short circuit button in basic position – In this position, the ignition circuit is
• Short circuit button pressed – In this position, the ignition circuit is interrupted,
closed, and the engine can be started.
a running engine stops, and a non-running engine will not start.
closed, and the engine can be started.
a running engine stops, and a non-running engine will not start.
500134-10

5.5Emergency OFF switch (EXC‑F AUS)

500131-10
The emergency OFF switch is fitted on the right side of the handlebar.
Possible states
Ignition off – In this position, the ignition circuit is interrupted, a run­ning engine stops, and a non-running engine will not start.
Ignition on – In this position, the ignition circuit is closed, and the engine can be started.
CONTROLS 13

5.6Electric starter button (EXC‑F EU, EXC‑F SIX DAYS, XCF‑W)

The electric starter button is fitted on the right side of the handlebar.
Possible states
• Electric starter button in basic position
• Electric starter button pressed – In this position, the electric starter is actuated.
400198-10

5.7Electric starter button (EXC‑F AUS)

The electric starter button is fitted on the right side of the handlebar.
Possible states
• Electric starter button in basic position
• Electric starter button pressed – In this position, the electric starter is actuated.
500131-11

5.8Light switch (EXC-F, EXC‑F SIX DAYS)

500134-12

5.9Horn button (EXC-F, EXC‑F SIX DAYS)

The light switch is fitted on the left side of the handlebar.
Possible states
Light off – Light switch is turned to the right. In this position, the light is switched off.
Low beam on – Light switch is in the central position. In this position, the low beam and tail light are switched on.
High beam on – Light switch is turned to the left. In this position, the high beam and the tail light are switched on.
The horn button is fitted on the left side of the handlebar.
Possible states
• Horn button in neutral position
• Horn button pressed – The horn is operated in this position.
500134-11

5.10Turn signal switch (EXC-F, EXC‑F SIX DAYS)

Turn signal switch is fitted on the left side of the handlebar.
Possible states
500145-10
Turn signal light off – Turn signal switch is in the central position. Turn signal light, left, on – Turn signal switch turned to the left.
Turn signal light, right, on – Turn signal switch turned to the right.
CONTROLS 14

5.11Overview of indicator lamps (EXC-F, EXC‑F SIX DAYS)

Possible states
High beam indicator lamp lights up blue – High beam is switched on.
Turn signal indicator lamp flashes green – Turn signal light is switched on.
500147-01
CONTROLS (EXC‑F, EXC‑F SIX DAYS, XCF-W) 15

6.1Speedometer

– Press the key to change the display mode or change to one of the setup menus. – Press the button to control different functions. – Press the button to control different functions.
Info
In its condition at delivery, the display mode SPEED/H andSPEED/ODO is acti­vated.
400312-01

6.2Speedometer activation and test

Activating the speedometer: The speedometer is activated when one of the keys is pressed or a signal is received from the wheel speed sensor. Display test For the function test of the display, all display segments light up briefly.
400313-01
WS (wheel size) After the display function test, the wheel size WS is displayed briefly.
Info
2205 mm corresponds to the size of the 21" front wheel with a series produc­tion tire.
The display then changes to the last selected mode.
400314-01

6.3Tripmaster switch

(Option: Tripmaster switch)
You can use the trip master switch to control the functions of the speedometer from the handlebar.
Info
The trip master is an optional accessory.

6.4Setting kilometers or miles

Info
If you change the unit of measure, the ODO value is retained and converted accordingly. The values TR1, TR2, A1, A2 and S1 are cleared when the unit of measure is changed.
400329-01
Condition
The motorcycle is stationary. – Press the button briefly and repeatedly until H appears at the bottom right of the
display.
– Press the button for 3 - 5 seconds.
The Setup menu opens and the active functions are displayed.
– Press the button repeatedly until the Km/h/Mph display flashes. Adjusting Km/h
– Press the button .
Adjusting Mph
– Press the button .
CONTROLS (EXC‑F, EXC‑F SIX DAYS, XCF-W) 16
– Press the button for 3 - 5 seconds.
The settings are saved and the Setup menu closed.
Info
If no button is pressed for 20 seconds, or if no impulse comes from the wheel speed sensor, the settings are automatically saved and the Setup menu is closed.

6.5Setting the clock

Condition
The motorcycle is stationary. – Press the button briefly and repeatedly until CLK appears at the bottom right of
the display.
– Press the button for 3 - 5 seconds.
The hour display flashes.
– Set the hour display with the button and/or button . – Press the button briefly.
The next segment of the display flashes and can be set.
400330-01
– You can set the following segments in the same way as the hours by pressing the
button and the button .
Info
The seconds can only be set to zero.
– Press the button for 3 - 5 seconds.
The settings are saved and the Setup menu closed.
Info
If no button is pressed for 20 seconds, or if no impulse comes from the wheel speed sensor, the settings are automatically saved and the Setup menu is closed.

6.6Adjusting the speedometer functions

Info
Upon delivery, only the SPEED/H and SPEED/ODO display modes are activated.
Condition
The motorcycle is stationary. – Press the button briefly and repeatedly until H appears at the bottom right of the
display.
– Press the button for 3 - 5 seconds.
The Setup menu opens and the active functions are displayed.
– Switch to the function you require by briefly pressing the button .
The selected function flashes.
Activating a function
– Press the button .
400318-01
Deactivating a function
– Press the button .
– Activate or deactivate all functions accordingly. – Press the button for 3 - 5 seconds.
The icon remains in the display and the display changes to the next func­tion.
The icon disappears from the display and the display changes to the next function.
The settings are saved and the Setup menu closed.
CONTROLS (EXC‑F, EXC‑F SIX DAYS, XCF-W) 17
Info
If no button is pressed for 20 seconds, or if no impulse comes from the wheel speed sensor, the settings are automatically saved and the Setup menu is closed.

6.7Querying the lap time

Info
This function can be called only if lap times are measured.
Condition
The motorcycle is stationary. – Press the button briefly and repeatedly until LAP appears at the bottom right of
the display.
– Press the button briefly.
LAP 1 appears on the left side of the display.
– Laps 1-10 can be displayed by pressing the button . – The button has no function – Press the button briefly.
400321-01
Next display mode
Info
If an impulse is received from the wheel speed sensor, the left side of the display changes back to the SPEED mode.

6.8SPEED display mode (speed)

400317-02

6.9Display mode SPEED/H (service hours)

400316-01
– Press the button briefly and repeatedly until SPEED appears on the left side of
the display.
The current speed is displayed in the SPEED display mode. The current speed can be displayed in Km/h or Mph.
Info
Making the setting according to the country. When an impulse comes from the front wheel, the left side of the speedometer display changes to the SPEED mode and the current speed is shown.
Condition
• The motorcycle is stationary – Press the button briefly and repeatedly until H appears at the bottom right of the
display.
In display mode H, the service hours of the engine are displayed. The service hour counter stores the total traveling time.
Info
The service hour counter is necessary for ensuring that maintenance work is car­ried out at the right intervals. If the speedometer is in H display mode at the start of the journey, it automati­cally changes to the ODO display mode. The H display mode is suppressed during the journey.
Press the button . No function Press the button . No function Press the button
for 3 - 5 seconds. Press the button
The display changes to the Setup menu of the speedometer functions.
Next display mode
briefly.
CONTROLS (EXC‑F, EXC‑F SIX DAYS, XCF-W) 18

6.10Display mode SPEED/CLK (clock)

– Press the button briefly and repeatedly until CLK appears at the bottom right of
the display.
The time is displayed in CLK display mode.
Press the button . No function Press the button . No function
400319-01

6.11Display mode SPEED/LAP (lap time)

Press the button for 3 - 5 seconds.
Press the button briefly.
– Press the button briefly and repeatedly until LAP appears at the bottom right of
the display.
In the LAP display mode, up to 10 lap times can be timed with the stop watch.
Info
If the lap time continues after you press the button , 9 memory locations are already occupied. Lap 10 must be timed with the button .
The display changes to the Setup menu of the clock.
Next display mode
400320-01

6.12Display mode SPEED/ODO (odometer)

400317-01

6.13Display mode SPEED/TR1 (trip master 1)

Press the button . Starts or stops the clock. Press the button . Stops the current lap time and saves it, and the stop watch
starts the next lap.
Press the button
The stop watch and the lap time are reset.
for 3 - 5 seconds. Press the button
Next display mode
briefly.
– Press the button briefly and repeatedly until ODO appears at the bottom right of
the display.
In ODO display mode, the total number of kilometers ridden is displayed.
Press the button . No function Press the button . No function Press the button
–
for 3 - 5 seconds. Press the button
Next display mode
briefly.
– Press the button briefly and repeatedly until TR1 appears at the top right of the
display.
TR1 (trip master 1) runs constantly and counts up to 999.9. You can use it to measure trips or the distance between refuelling stops. TR1 is coupled with A1 (average speed 1) and S1 (stop watch 1).
400323-01
Info
If 999.9 is exceeded, the values of TR1, A1 and S1 are automaticallt reset to
0.0.
Press the button . No function Press the button . No function Press the button
for 3 - 5 seconds.
Displays of TR1, A1 and S1 are reset to 0,0.
CONTROLS (EXC‑F, EXC‑F SIX DAYS, XCF-W) 19

6.14Display mode SPEED/TR2 (trip master 2)

400324-01

6.15Disply mode SPEED/A1 (average speed 1)

Press the button
Next display mode
briefly.
– Press the button briefly and repeatedly until TR2 appears at the top right of the
display.
TR2 (trip master 2) runs constantly and counts up to 999.9. The displayed value can be set manually with the button and the button . A very practical function when riding using the road book.
Info
The TR2 value can also be corrected manually during the journey with the but­ton and the button . If 999.9 is exceeded, the value of TR2 is automatically reset to 0.0.
Press the button . Increases value of TR2. Press the button . Reduces value of TR2. Press the button
for 3 - 5 seconds. Press the button
briefly.
– Press the button briefly and repeatedly until A1 appears at the top right of the
display.
A1 (average speed 1) shows the average speed calculated using TR1 (trip master 1) and S1 (stop watch 1).
The calculation of this value is activated by the first impulse of the wheel speed sensor and ends 3 seconds after the last impulse.
Deletes value of TR2.
Next display mode
400325-01

6.16Display mode SPEED/A2 (average speed 2)

– Press the button briefly and repeatedly until A2 appears at the top right of the
A2 (average speed 2) shows the average speed on the basis of the current speed if the stop watch S2 (stop watch 2) is running.
400326-01
Press the button . No function Press the button . No function Press the button
Displays of TR1, A1 and S1 are reset to 0,0.
for 3 - 5 seconds. Press the button
Next display mode
briefly.
display.
Info
The displayed value can differ from the actual average speed if S2 was not timed after the ride.
Press the button . No function Press the button . No function Press the button
for 3 - 5 seconds. Press the button
briefly.
–
Next display mode
CONTROLS (EXC‑F, EXC‑F SIX DAYS, XCF-W) 20

6.17Display mode SPEED/S1 (stop watch 1)

– Press the button briefly and repeatedly until S1 appears at the top right of the
display.
S1 (stop watch 1) displays the journey time on the basis of TR1 and continues when an impulse is received from the wheel speed sensor. The calculation of this value starts with the first impulse of the wheel speed sensor and ends 3 seconds after the last impulse.
Press the button . No function
400327-01

6.18Display mode SPEED/S2 (stop watch 2)

Press the button . No function Press the button
Displays of TR1, A1 and S1 are reset to 0,0.
for 3 - 5 seconds. Press the button
Next display mode
briefly.
– Press the button briefly and repeatedly until S2 appears at the top right of the
display.
S2 (stop watch 2) is a manual stop watch. If S2 is running in the background, the S2 display flashes in the speedometer display.
Press the button . Starts or stops S2. Press the button . No function
400328-01
Press the button for 3 - 5 seconds.
Press the button
Displays of S2 and A2 are reset to 0.0.
Next display mode
briefly.
Table of functions Display Press the button . Press the button . Press the button for 3 -
5 seconds.
Display mode SPEED/H (service hours)
No function No function The display changes to
the Setup menu of the speedometer functions.
Display mode SPEED/CLK (clock)
No function No function The display changes to
the Setup menu of the clock.
Display mode SPEED/LAP (lap time)
Starts or stops the clock.
Stops the current lap time and saves it, and
The stop watch and the
lap time are reset. the stop watch starts the next lap.
Display mode
No function No function – Next display mode
SPEED/ODO (odometer) Display mode SPEED/TR1
(trip master 1) Display mode SPEED/TR2
No function No function Displays of TR1, A1 and
S1 are reset to 0,0.
Increases value of TR2. Reduces value of TR2. Deletes value of TR2. Next display mode
(trip master 2) Disply mode SPEED/A1
(average speed 1) Display mode SPEED/A2
No function No function Displays of TR1, A1 and
S1 are reset to 0,0.
No function No function – Next display mode
(average speed 2) Display mode SPEED/S1
(stop watch 1) Display mode SPEED/S2
(stop watch 2)
No function No function Displays of TR1, A1 and
S1 are reset to 0,0.
Starts or stops S2. No function Displays of S2 and A2
are reset to 0.0.
Press the button briefly.
Next display mode
Next display mode
Next display mode
Next display mode
Next display mode
Next display mode
Next display mode
Table of conditions and activability Display The motorcycle is
stationary
Display mode SPEED/H (service hours) •
Menu can be acti­vated
CONTROLS (EXC‑F, EXC‑F SIX DAYS, XCF-W) 21
Table of conditions and activability Display The motorcycle is
stationary
Display mode SPEED/CLK (clock) • Display mode SPEED/LAP (lap time) • Display mode SPEED/TR1 (trip master 1) • Display mode SPEED/TR2 (trip master 2) • Disply mode SPEED/A1 (average speed 1) • Display mode SPEED/A2 (average speed 2) • Display mode SPEED/S1 (stop watch 1) • Display mode SPEED/S2 (stop watch 2) •
Menu can be acti­vated

CONTROLS 22

7.1Fuel tap (EXC‑F, EXC‑F SIX DAYS, XCF-W)

The fuel tap is on the left side of the fuel tank. Using tap handle on the fuel tap, you can open or close the supply of fuel to the carburetor.
Possible states
• Fuel supply closed OFF – No fuel can flow from the tank to the carburetor.
• Fuel supply open ON – Fuel can flow from the tank to the carburetor. The fuel tank empties down to the reserve.
• Reserve fuel supply open RES – Fuel can flow from the tank to the carburetor. The fuel tank empties completely.
500137-10

7.2Fuel tap (SX‑F)

7.3Opening filler cap

The fuel tap is on the left side of the fuel tank. Using tap handle on the fuel tap, you can open or close the supply of fuel to the carburetor.
Possible states
• Fuel supply closed OFF – No fuel can flow from the tank to the carburetor.
• Fuel supply open ON – Fuel can flow from the tank to the carburetor. The fuel tank empties completely.
500178-10
– Press release button , turn filler cap counterclockwise and lift it upwards and
remove.
400199-10
CONTROLS 23

7.4Closing filler cap

– Replace the filler cap and turn clockwise until the release button locks in place.
Info
Route the fuel tank breather hose without kinking.
400199-11

7.5Choke (EXC-F EU, EXC‑F SIX DAYS)

The choke lever is fitted on the left side of the handlebar. Activating the choke function frees an opening through which the engine can draw extra fuel. This gives a richer fuel-air mixture, which is needed for a cold start.
Info
If the engine is warm, the choke function must be deactivated.
Possible states
500136-10
• Choke function activated – The choke lever is pulled to the stop.
• Choke function deactivated – The choke lever is pushed back to the stop.

7.6Choke (XCF‑W, SX‑F, EXC‑F AUS)

600660-10

7.7Shift lever

600661-13
Choke is fitted on the left side of the carburetor. Activating the choke function frees an opening through which the engine can draw extra fuel. This gives a richer fuel-air mixture, which is needed for a cold start.
Info
If the engine is warm, the choke function must be deactivated.
Possible states
• Choke function activated – The choke lever is pulled out to the stop.
• Choke function deactivated – The choke lever is pushed in to the stop.
Shift lever is mounted on the left side of the engine.
The gear positions can be seen in the photograph. The neutral or idle position is between the first and second gears.
600661-10
CONTROLS 24

7.8Foot brake lever

Foot brake lever is located in front of the right footrest. The foot brake lever is used to activate the rear brake.
600664-10

7.9Kick starter

The kick starter is fitted on the right of the engine. The engine can be started with either the kick starter or the electric starter. The upper part of the kick starter can be swung out.
Info
Before riding, swing the upper part of the kick starter inwards towards the engine.
600664-11

7.10Side stand (EXC‑F, EXC‑F SIX DAYS, XCF-W)

Note
Danger of damage The parked vehicle can roll away or fall over.
– Always place the vehicle on a firm and even surface.
Note
Material damage Damage and destruction of components by excessive load.
– The side stand is designed for the weight of the motorcycle only. Do not sit on the
500140-10
To park the motorcycle, press the side stand to the ground with your foot and lean the motorcycle on it.
When you are riding, the side stand must be folded up and secured with the rubber band .
motorcycle when it is supported by the side stand only. The side stand and/or the frame could be damaged and the motorcycle could fall over.

7.11Plug-in stand (SX‑F)

600665-10
400203-10
Note
Danger of damage The parked vehicle can roll away or fall over.
– Always place the vehicle on a firm and even surface.
To park the motorcycle, insert plug-in stand into the left side of the wheel spindle.
Info
Remove the plug-in stand before starting on a trip.
CONTROLS 25

7.12Steering lock (EXC-F, EXC‑F SIX DAYS)

Steering lock is fitted on the left side of the steering head. The steering lock is used to lock the steering. Steering, and therefore riding, is no longer possible.
500126-10

7.13Locking the steering (EXC-F, EXC‑F SIX DAYS)

Note
Danger of damage The parked vehicle can roll away or fall over.
– Always place the vehicle on a firm and even surface.
– Park the vehicle. – Turn the handlebar as far as possible to the right. – Insert the key in the steering lock, turn it to the left, press it in and turn it to the
right. Remove the key.
Steering is no longer possible.
400732-01

7.14Unlocking the steering (EXC-F, EXC‑F SIX DAYS)

– Insert the key in the steering lock, turn it to the left, pull it out and turn it to the
right. Remove the key.
400731-01
Info
Never leave the key in the steering lock.
You can now steer the bike again.
Info
Never leave the key in the steering lock.

GENERAL TIPS AND HINTS ON PUTTING INTO OPERATION 26

8.1Advice on first use

Danger
Danger of accidents Danger arising from the rider's judgement being impaired.
– Do not use the vehicle if you are inexperienced or if you have consumed alcohol or drugs.
Warning
Risk of injury Missing or poor protective clothing present an increased safety risk.
– Wear protective clothing (helmet, boots, gloves, pants and jacket with protectors) every time you ride the vehicle. Always
wear protective clothing, which must be undamaged and meet legal requirements.
Warning
Danger of crashing Poor vehicle handling due to different tire tread patterns on front and rear wheels.
– The front and rear wheels must be fitted with tires with similar tread patterns to prevent loss of control over the vehicle.
Warning
Danger of accidents Critical handling characteristic due to inappropriate riding style.
– Adapt your riding speed to the road conditoins and your riding ability.
Warning
Danger of accidents Accident risk caused by presence of a passenger.
– Your vehicle is not designed to carry passengers. Do not ride with a passenger.
Warning
Danger of accidents Failure of brake system.
– If the foot brake lever is not released, the brake linings drag permanently. The rear brake can fail due to overheating. Take
your foot off the foot brake lever if you do not want to brake.
Warning
Danger of accidents Unstable riding behavior.
– Do not exceed the maximum permissible weight and axle loads.
Warning
Risk of misappropriation Usage by unauthorized persons.
– Never leave the vehicle while the engine is running. Secure the vehicle against use by unauthorized persons.
Info
When using your motorcycle, remember that others may feel disturbed by excessive noise.
– Make sure that the pre-delivery inspection work has been carried out by an authorized KTM workshop.
You receive a delivery certificate and the service record at vehicle handover.
– Before your first trip, read the entire operating instructions carefully. – Get to know the controls. – Adjust the basic position of clutch lever. ( p. 83) (XCF‑W, SX‑F)
– adjust the basic position of hand brake lever. ( p. 62)
(EXC-F, EXC‑F SIX DAYS)
– Adjust the free travel of the hand brake lever. ( p. 62)
–
Adjust the basic position of the footbrake lever. x ( p. 66)
–
Adjust the basic position of the shift lever. x ( p. 84)
– Get used to handling the motorcycle on a suitable piece of land before making a longer trip.
Info
Offroad, you should be accompanied by another person on another machine so that you can help each other.
– Try also to ride as slowly as possible and in a standing position to get a better feeling for the vehicle. – Do not make any offroad trips that over-stress your ability and experience. – Hold the handlebar firmly with both hands and keep your feet on the footrests when riding.
GENERAL TIPS AND HINTS ON PUTTING INTO OPERATION 27
(EXC‑F, EXC‑F SIX DAYS, XCF-W)
– If you carry any baggage, make sure it is fixed firmly as close as possible to the center of the vehicle and ensure even weight
distribution between the front and rear wheels.
Info
Motorcycles react sensitively to any changes of weight distribution.
(SX‑F)
– Do not transport luggage.
– Do not exceed the overall maximum permitted weight and the axle loads.
Guideline
Maximum permissible overall weight 335 kg (739 lb.) Maximum permissible front axle load 145 kg (320 lb.) Maximum permissible rear axle load 190 kg (419 lb.)
– Check the spoke tension. ( p. 73)
Info
The spoke tension must be checked after half an hour of operation.
– Run the engine in.

8.2Running-in the engine

– During the running-in phase, do not exceed the specified engine speed and engine performance.
Guideline
Maximum engine speed
During the first 3 service hours 7,000 rpm
Maximum engine performance
During the first 3 service hours ≤ 50 % During the next 12 service hours ≤ 75 %
– Avoid fully opening the throttle!

8.3Preparing vehicle for arduous riding conditions

– Using a motorcycle in arduous conditions can lead to excessive wear of components such as the power train or brakes. For this
reason, it may be necessary to service or replace worn parts before the limit specified in the service schedule is reached.
Arduous riding conditions are:
– Riding on dry sand. ( p. 27) – Riding on wet sand. ( p. 28) – Riding on wet and muddy surfaces. ( p. 29) – Rides at high temperature and slow speed. ( p. 30) – Rides at low temperatures or in snow. ( p. 30)

8.4Preparing for riding on dry sand

– Check the radiator cap.
Value on radiator cap 1.8 bar (26 psi)
» If the displayed value does not correspond to specifications:
Warning
Danger of scalding During motorcycle operation, the coolant gets
very hot and is under pressure.
600872-10
– Do not remove the radiator cap, radiator hoses or other cooling
system components when the engine is hot. Allow the engine and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.
– Change the radiator cap.
–
Seal the air filter box. x
GENERAL TIPS AND HINTS ON PUTTING INTO OPERATION 28
Tip
Seal the air filter box on the edges against dirt.
–
Clean the air filter. x ( p. 82)
Info
Check the air filter approx. every 30 minutes.
– Fit a dust protection device on the air filter.
Dust protection device for air filter (59006019000)
Info
See the KTM PowerParts fitting instructions.
600869-01
– Fit a sand screen device on the air filter.
Sand protection device for air filter (59006022000)
Info
See the KTM PowerParts fitting instructions.
600871-01
600868-01

8.5Preparing for riding on wet sand

600872-10
– Adjust the carburetor jetting and settings.
Info
Your authorized KTM workshop has the recommended carburetor tuning set­tings.
– Clean the chain.
Chain cleaner ( p. 117)
– Fit the steel sprocket.
Tip
Do not grease the chain.
– Clean radiator fins. – Straighten bent radiator fins carefully.
– Check the radiator cap.
Value on radiator cap 1.8 bar (26 psi)
» If the displayed value does not correspond to specifications:
Warning
Danger of scalding During motorcycle operation, the coolant gets
very hot and is under pressure.
– Do not remove the radiator cap, radiator hoses or other cooling
system components when the engine is hot. Allow the engine and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.
– Change the radiator cap.
–
Seal the air filter box. x
Tip
Seal the air filter box on the edges against dirt.
–
Clean the air filter. x ( p. 82)
Loading...
+ 95 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use