Krups FNP1 User Manual

lock

www.krups.com

c b

a

lock

d
e

h
h1

i

j

g2

g

g1

f1

f

k

1

2

3

2

1

54 6

7

8

9

10

4

Espremio 01 FNP1

USA 6

Instructions for Use
Warranty
Guarantee of Performance

Français 15

Mode d’emploi
Garantie
Garantie de rendement

Español 24

Instrucciones de uso
Garantía
Garantía de rendimiento

5

USA

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and/or
injury to persons, including the following:

•Read all instructions.

•Do not touch hot surfaces. Use handles or knobs.

•To protect against fire, electric shock and injury to persons, do not
immerse cord, plugs, or appliance in water or other liquid.

•Close supervision is necessary when any appliance is used by or
near children.

•Unplug from outlet when not in use and before cleaning. Allow to
cool before putting on or taking off parts, and before cleaning the
appliance.

•Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Return appliance to your nearest authorized KRUPS
Service Center for examination, repair or adjustment (see
Guarantee of Performance).

•The use of accessory attachments not recommended by KRUPS
may result in fire, electric shock or injury to persons.

•Do not use outdoors.

•Do not let cord hang over edge of table or counter, or touch hot
surfaces.

•Do not place on or near a hot gas or electric burner, or in a heated
oven.

•To disconnect, turn switch to “OFF”, then remove plug from wall
outlet.

•Do not use appliance for other than intended use.

•Use extreme caution when dispensing hot steam.

SAVE THESE INSTRUCTIONS

6

CAUTION

•This appliance is for household use only. Any servicing other than
routine cleaning and user maintenance should be performed by
authorized KRUPS service personnel only (see Guarantee of
Performance).

•Do not immerse base in water.

•To reduce the risk of fire or electric shock, do not remove the base
of the machine. There are no user serviceable parts inside. Repairs
should be performed by authorized KRUPS service personnel only.

SPECIAL CORD SET INSTRUCTIONS

Regarding your Cord Set:
A. A short power-supply cord is to be provided to reduce risks

resulting from becoming entangled in or tripping over a longer
cord.

B. Longer extension cords are available and may be used if care is

exercised in their use.

C. If a long extension cord is used, (1) the marked electrical rating

of the extension cord should be at least as great as the electrical
rating of the appliance, (2) the longer cord should be arranged
so that it will not drape over the counter top or table top where
it can be pulled on by children or tripped over.

D. This appliance has a polarized plug (one blade is wider than the

other). To reduce the risk of electric shock, this plug is intended
to fit into a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to modify the
plug in any way.

7

Description

a Lid + water tank
b Function selector
c Temperature control indicator light
d Percolation head
e Level indicator of water
f Filter holder

f1 filter for one cup (ground coffee)
g Steam nozzle for heating liquids
g1 tip
g2 sliding part
h On /Off switch with included lamp
h1 operating indicator light

i Grid
j Drip tray
k Measuring spoon

Safety recommendations

• Read the instructions for use carefully
before using your appliance for the first
time: any use which does not conform
to these instructions will absolve KRUPS
from any liability.

• Never leave the appliance within the
reach of small children. The use of this
appliance by young children or disabled
persons must always be under close
supervision.

• Check that the voltage rating of your
appliance matches that of your household
electrical wiring system.

Any connection error will render the
guarantee null and void.

• Do not allow the power cord to hang down
within reach of children.

• Do not remove the filter holder containing
the coffee grounds while water is running
through, as the appliance is then under
pressure.

• Do not use the appliance when the drip tray
and the grid are not in place.

• Never unplug the appliance by pulling on
the cord.

• Make sure the filter holder is well tightened
before starting to make coffee. Reset the

8

selector to O before loosening the filter
holder.

• All the appliances made by KRUPS are
subjected to strict 100 % inspection.
Practical user tests are performed with a
number of appliances taken at random,
which explains any traces of utilization.

Espresso coffee

Espresso coffee is richer in flavor and stronger
than ordinary coffee. It is traditionally drunk
from small espresso cups which have been
pre-heated. Hot water and pressure combine
to passed through ground coffee in order to
obtain this delicious black, foamy coffee,
which has an invigorating effect.

You can always recognize genuine espresso
because of its characteristic flavor and rich,
delicious foam (crema). This however requires
both high pressure and your favorite espresso
coffee (which has been well roasted and
correctly ground). If you are unable to
purchase ground espresso coffee, use a coffee
grinder to grind the beans. The coffee must
not be ground «too fine». It should be slightly
grainy. If it is too fine, you run the risk of
blocking the grids of the percolation head and
the filter.

To guarantee complete success in making a
good espresso, it is necessary to use fresh,
clean, cold water—free of chlorine or other
impurities that can ruin the taste of your
coffee.

Before first use

• Clean the water heating system with one or
two tanks of clean water, as follows:

• Open the lid, lift out the tank and fill it with
water (1).

• Replace the tank, positioning it firmly in such
a way that the connecting valve situated
beneath the tank opens, and close the lid.

• Plug in the appliance.

• Set the «on/off» switch (h) . The indicator
light (h1) will come on.

• Place the filters in the filter holder without
any coffee. Then fit the assembly onto the
percolation head. To position the filter

holder correctly, point the handle to the left,
press the filter holder onto the percolation
head, then turn the handle to the right until
the lock position (2).

• Place as large an empty container as possible
under the filter holder.

• As soon as the appliance reaches the right
temperature, the temperature control
indicator light (c) will come on. Turn the
function selector (b) to the position «
and allow all the water contained in the tank
to run through the machine.

• If necessary, interrupt this operation by
turning the function selector (b) to the
position O to empty the container then
resume the operation.

»

Using the various functions of
your espresso

1. ESPRESSO FUNCTION

• For best results, preheat the accessories
(filter holder, filter and cups) by running
water directly into the cups (see «Before first
use»).

• When the cup are full of hot water, reset
the function selector (b) to the position O.

. Preparing an espresso with ground
coffee:

• Fill the water container with fresh, cold
water (1).

• Set the «on/off» switch (h). The indicator
light (h1) will come on.

• Put the filter for one cup in the filter holder.

• Put some ground coffee in the filter, firmly
pressing down the ground coffee with the
back of the spoon (1 measuring spoon = 1
cup) (3).

• Clean the edges of the filter holder.

• Put the filter holder in place (2).

• Place one espresso cup under the filter
holder.

As soon as the appliance reaches the correct
temperature, the indicator light (c) comes on.

• Then turn the function selector (b) to the
position «

• When the cups are full, reset the function
selector (b) to the position O.

».

• Take the filter holder out of the appliance,
and remove the ground coffee, holding the
filter in place with the gripper clamp (4).

The filter can now be refilled to prepare more
espressos.

2. STEAM FUNCTION

The thumping noise which occurs while steam
is being produced comes from the intermit­tent regulation of the pump and has no effect
on the proper working of the appliance.

Caution : during and after use of the
machine, the metallic parts of the steam
nozzle can become extremely hot.

. Preparing frothed and steamed milk for
a cappuccino, a latte or hot chocolate :

If you are making a cappuccino or latte, you
will need at least a 5 oz. cup (150 ml).

. Cappuccino is made using 1/3 espresso, 1/3

hot steamed milk and 1/3 frothed milk.

. Café latte is made using 1/2 espresso, 1/2

steamed milk, and topped with a bit of
frothy milk.

. Hot chocolate: heat the milk if you are

using powdered chocolate. Then simply mix
the powder in the heated milk.

Please note : the sliding part (g2) of the
nozzle must be in the down position (5).

• Fill the water container with fresh, cold
water (1).

• Set the «on/off» switch (h). The operating
light (h1) will come on.

• Move the nozzle towards the outside of the
appliance.

As soon as the appliance reaches the
appropriate temperature, the temperature
control indicator light (c) will come on.

• Place an empty container under the nozzle.
Return the nozzle to the inside and hold the
container by its handle or place it on the grid
(i) (6).

• Then turn the function selector (b) to the
position «
then reset it to the position O and remove
the container.

• Immerse the tip of the nozzle in the milk to
be heated. Return the nozzle to the inside
and hold the container by its handle or place
it on the grid (i) (6).

» until to obtain some steam

9

As soon as the appliance reaches the
appropriate temperature, the temperature
control indicator light (c) will come on.

• Then turn the function selector (b) to the
position « » until the milk is frothed
enough, then reset it to the position O and
remove the container.

• Do the cleaning operation in order to
prevent the nozzle from becoming blocked:

. place an empty container under the nozzle.
. then turn the function selector (b) to the

position «

. turn the function selector (b) to the position

O.

. clean the nozzle with a damp cloth.

• For thorough cleaning of the nozzle, please
refer to the paragraph «Maintenance».

. Heating water (for tea, for example) or
thick liquids (soup, for example)

Please note : the sliding part (g2) of the

nozzle must be in the raised position (5).

• Fill the water container with fresh, cold
water (1).

• Set the «on/off» switch (h). The indicator
light (h1) comes on.

• Move the nozzle towards the outside of the
appliance.

As soon as the appliance reaches the
appropriate temperature, the temperature
control indicator light (c) will come on.

• Place an empty container under the nozzle.
Return the nozzle to the inside and hold the
container by its handle or place it on the grid
(i) (6).

• Then turn the function selector (b) to the
position «
then reset it to the position O and remove
the container.

• Immerse the tip of the nozzle in the liquid to
be heated. Return the nozzle to the inside
and hold the container by its handle or place
it on the grid (i) (6).

As soon as the appliance reaches the
appropriate temperature, the temperature
control indicator light (c) will come on.

• Then turn the function selector (b) to the
position «
then reset it to the position O and remove
the container.

10

» again during few seconds.

» until to obtain some steam

» until the liquid is hot enough,

• For liquids other than water, do the cleaning
operation in order to prevent the nozzle
from becoming blocked:

. place an empty container under the nozzle.
. then turn the function selector (b) to the

position «

. turn the function selector (b) to the position

O.

. clean the nozzle with a damp cloth.

• For thorough cleaning of the nozzle, please
refer to the paragraph «Maintenance».

Notes
If you wish to make an espresso

immediately after steam, the appliance

must first cool down until it reaches the right
temperature for extraction.

• To do this, insert an empty filter holder (no
coffee) in the machine and position a
suitable container beneath it. Then turn the
function selector (b) to the position «

• Let the water run through until the indicator
light (c) goes out. Then, turn the function
selector (b) to the position O.

After this, the machine is now ready once
more to make an espresso (see paragraph
«espresso function»).

Please note: when the appliance is running,
and also afterwards, the nozzle will be very
hot. Allow time for the appliance to cool
down to prevent scalding or burning.

» again during few seconds.

».

Maintenance

• Unplug the appliance and allow it to cool.

• Never wash the accessories for your espresso
in the dishwasher.

• Clean the body of the appliance with a
damp cloth.

After use, the water tank must be emptied.

. The drip tray (j)

• Each time an espresso is prepared, the drip
tray fills with water. This is perfectly normal.
To prevent any overflow, remove the grid (7)
and empty the drip tray regularly.

• If necessary, clean the drip tray and the grid
with water and a little non-abrasive
washing-up liquid, rinse and dry. When
replacing, return the plastic block situated at
the back of the tray (8).