Krups Espremio, Espremio Auto cappuccino, Espremio Auto cappuccino FNP2, Espremio FNP1 Instructions For Use Manual

KRUPS

lock

I

0

e e

LP

f.',";~':..'.,

-

-

~

0

~

. -

~

FNP1/FNP2

c

a

KRUPS

~Iock

.~-

92J9

91

d

e

h.
h1

. a a.g:""~ ~ ~~a
E>a a aa a E>a a e -

aaaaa~i:§ :§e{;aaaa:;:

a ae:t :§ ~ aaeee

e e

e

f1

f

~

k

I

KRUPS

Espremio

Espremio Auto cappuccino

FNP1
FNP2

USA -

6

Instructions for Use
Warranty

Guarantee of Performance

Fran<;ais

15

Mode d'emploi
Garantie

Garantiede rendement

Espanol

24

Instrucciones de uso
Garantia

Garantia de rendimiento

33

Instructions for Use of steam
and AutocappuCCIno functions of FNP2

Fran<;ais

36

Mode d'emploi pour lesfonctions
vapeur et Autocappuccino FNP2

Espanol

38

Instrucciones de uso per funcion vapor
y Autocappuccino FNP2

ORUPS5

--- -- -- ---

-

.

Em

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should

always be followed to reduce the risk of fire, electric shock and/or
injury to persons, including the following:

-Read all instructions.

-Do not touch hot surfaces. Use handles or knobs.

-To protect against fire, electric shock and injury to persons, do not
immerse cord, plugs, or appliance inwater or other liquid.

-Close supervision is necessary when any appliance is used by or
near children.

-Unplug from outlet when not in use and before cleaning. Allow to
cool before putting on or taking off parts, and before cleaning the
appliance.

-Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Return appliance to your nearest authorized KRUPS
Service Center for examination, repair or adjustment (see

Guarantee of Performance).

-The use of accessory attachments not recommended by KRUPS

may result in fire, electric shock or injury to persons.

-Do not use outdoors.

-Do not let cord hang over edge of table or counter, or touch hot
surfaces.

-Do not place on or near a hot gas or electric burner, or in a heated
oven.

-To disconnect, turn switch to "OFF",then remove plug from wall
outlet.

-Do not use appliance for other than intended use.

-Use extreme caution when dispensing hot steam.

SAVE THESE INSTRUCTIONS

6 KRUPS

- -- -- -- - - -- - - -- - - -- - - - - - - - -

CAUTION

-This appliance isfor household use only. Any servicing other than
routine cleaning and user maintenance should be performed by
authorized KRUPSservice personnel only (see Guarantee of

Performance).

-Do not immerse base in water.

-To reduce the risk of fire or electric shock, do not remove the base
of the machine. There are no user serviceable parts inside. Repairs
should be performed by authorized KRUPSservice personnel only.

SPECIAL CORD SET INSTRUCTIONS

Regarding your Cord Set:
A. A short power-supply cord is to be provided to reduce risks

resulting from becoming entangled in or tripping over a longer
cord.

B. Longer extension cords are available and may be used if care is

exercised in their use.

e. If a long extension cord is used, (1) the marked electrical rating

of the extension cord should be at least asgreat as the electrical
rating of the appliance, (2) the longer cord should be arranged
so that it will not drape over the counter top or table top where
it can be pulled on by children or tripped over.

D. This appliance has a polarized plug (one blade is wider than the

other). To reduce the risk of electric shock, this plug is intended
to fit into a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does not fit,

contact a qualified electrician. Do not attempt to modify the
plug in any way.

KRUPS7

Description

a
b

Lid+ water

tank

Function selector

Temperature control indicator light

Percolation head
LevelIndicator of water
Filter holder

filter for one cup (ground coffee)

Steam nozzle for heating liquids
tip
sliding part
On /Off switch with included lamp
operating indicator light

Grid
Drip tray

Measuring spoon

c
d
e
f
f1

g
gl
g2

h
h1

j

k

Safety recommendations ,,:~

.Read the instructions for use carefully

before using your appliance for the first
time: any use which does not conform

to these instructions will absolve KRUPS
from any liability.

.Never leave the appliance within the

reach of small children. The useof this
appliance by young children or disabled

persons must always be under close
supervision.

.Check that the voltage rating of your

appliance matches that of your household

electrical wiring system.

Any connection error will render the
guarantee null and void.

.Do not allow the power cord to hang down

within reach of children.

. Do not remove the filter holder containing

the coffee grounds while water is running
through, asthe appliance is then under
pressure.

. Do not usethe appliance when the drip tray

and the grid are not in place.

. Neverunplug the appliance by pulling on

the cord.

. Make sure the filter holder is well tightened

before starting to make coffee. Resetthe

8 KRUPS

selector to 0 before loosening the filter
holder

. All the appliances made by KRUPSare

subjected to strict 100 % inspection.
Practicaluser tests areperformed with a
number of appliances taken at rahdom,
which explainsany traces of utilization

ES,m!$so';coffee

Espressocoffee is richer in flavor and stronger
than ordinary coffee. It istraditionally drunk
from small espressocups which have been
pre-heated. Hot water and pressurecombine
to passedthrough ground coffee in order to
obtain this delicious black, foamy coffee,
which hasan invigorating effect.

You can always recognize genuine espresso

becauseof its characteristic flavor and rich,
delicious foam (crema). This however requires
both high pressureand your favorite espresso
coffee (which has been well roasted and
correctly ground). If you are unable to
purchaseground espressocoffee, usea coffee
grinder to grind the beans. The coffee must
not be ground «too fine». It should be slightly
grainy. If It istoo fine, you run the risk of
blocking the grids of the percolation head and

the filter
Toguarantee complete successin making a

good espresso,it is necessaryto usefresh,
clean, cold water-free of chlorine or other

impurities that can ruin the taste of your

coffee.

.Cleanthe water heating systemwith one or

two tanks of clean water, asfollows:

. Open the lid, lift out the tank and fill it with

water (1)

. Replacethe tank, positioning it firmly In such

a way that the connecting valve situated

beneath the tank opens, and close the lid.

. Plug in the appliance.

.Set the «on/off» switch (h) . The indicator

light (h1) will come on.

.Place the filter in the filter holder without

anycoffee.Thenfit theassemblyonto the

percolation head. Toposition the filter

holder correctly, pOint the handle to the left,
pressthe filter holder onto the percolation
head, then turn the handle to the right until
the lock position (2)

.Placeas large an empty container as possible

under the filter holder.

.As soon as the appliance reachesthe right

temperature, the temperature control
indicator light (c)will come on. Turn the
function selector (b) to the position «~»

and allow all the water contained in the tank
to run through the machine.

.If necessary,interrupt this operation by

turning the function selector (b) to the
position 0 to empty the container then
resumethe operation

Using the vario]
your espresso.:

.,tions of

1. ESPRESSOFUNCTION

.For best results, preheat the accessories

(filter holder, filter and cups) by running
water directly into the cups (see «Before first
use»).

. Whenthecuparefullofhotwater,reset

the function selector (b) to the position O.

. Preparing an espresso with ground
coffee:

.Fill the water container with fresh, cold

water (1)

.Setthe «on/off» switch (h) The indicator

light (h1)will come on.

.Put the filter for one cup in the filter holder

.Put some ground coffee in the filter, firmly

pressing down the ground coffee with the
back of the spoon (1 measuring spoon = 1
cup) (3)

.Cleanthe edgesof thefilter holder.

.Put the filter holder in place (2)

.Placeone espressocup under the filter

holder.

As soon as the appliance reachesthe correct
temperature, the indicator light (c)comes on.

.Then turn the function selector (b) to the

position «~».

.When the cups are full, resetthe function

selector (b) to the position O.

.Takethe filter holder out of the appliance,

and remove the ground coffee, holding the
filter in place with the gripper clamp (4).

The filter can now be refilled to prepare more
espressos.

2. STEAM FUNCTION

The thumping noise which occurs while steam
is being produced comesfrom the intermit-
tent regulation of the pump and hasno effect
on the proper working of the appliance.

Caution: during and after use of the
machine, the metallic parts of the steam
nozzle can become extremely hot.

. Preparing frothed and steamed milk for

a cappuccino, a latte or hot chocolate:

If you aremaking a cappuccino or latte, you

will need at least a 5 oz cup (150 ml)

. Cappuccino ismade using 1/3 espresso, 1/3

hot steamed milk and 1/3frothed milk.

. Cafe latte ismade using 1/2 espresso, 1/2

steamed milk, and topped with a bit of
frothy milk.

. Hot chocolate: heat the milk if you are

using powdered chocolate. Then simply mix
the powder in the heated milk.

Please note: the sliding part (g2) of the
nozzle must be in the down position (5)

.Fillthe water container with fresh, cold

water (1).

.Set the «on/off» switch (h). The operating

light (h1) will come on.

.Move the nozzle towards the outside of the

appliance.

As soon asthe appliance reachesthe
appropriate temperature, the temperature
control indicator light (c) will come on.

.Placean empty container under the nozzle.

Return the nozzleto the inside and hold the
container by itshandle or place it on the grid

(I)(6)

.Then turn the function selector (b) to the

position «6» until to obtain some steam

then resetit to the position 0 and remove
the container

.Immerse the tip of the nozzle in the milk to

be heated. Return the nozzle to the inside
and hold the container by its handle or place

it on the grid (i) (6)

KRUPS9

Assoon as the appliance reachesthe

appropriate temperature, the temperature
control indicator light (c) will come on.

.Then turn the function selector (b) to the

position «\!!\.J» untilthe milkisfrothed

enough, then reset it to the pOSItion 0 and
remove the container.

.Do the cleaning operation In order to

prevent the nozzle from becoming blocked:
place an empty container under the nozzle.

. then turn the function selector (b) to .the

position «\!!\.J»again during few seconds.

. turnthefunctionselector(b)to the position

O.

clean the nozzle with a damp cloth.

.Forthorough cleaning of the nozzle, please

refer to the paragraph «Maintenance».

. Heating water (for tea, for example) or
thick liquids (soup, for example)

Please note: the sliding part (g2) of the

nozzle must be in the raised position (5).

.Fillthe water container with fresh, cold

water (1)

.Set the «on/off» switch (h) The indicator

light (h 1) comes on.

.Move the nozzle towards the outside of the

appliance.

Assoon as the appliance reaches the

appropriate temperature, the temperature
control indicator light (c)willcome on.

.Place an empty container under the nozzle.

Return the nozzle to the Inside and hold the
container by its handle or place it on the grid

(i) (6)

.Then turn the function selector (b) to the

position«\!!\.J»untilto obtainsomesteam

then reset it to the position 0 and remove
the container

.Immerse the tip of the nozzle in the liquid to

be heated. Return the nozzleto the inside
and hold the container by Itshandle or place

It on the grid (i) (6)

Assoon as the appliance reaches the
appropriate temperature, the temperature
control indicator light (c)willcome on.

.Then turn the function selector (b) to the

position «\!!\.J» until the liquid IShot enough,

then reset it to the position 0 and remove
the container.

10 KRUPS

.Forliquidsother than water, do the cleaning

operation in order to prevent the nozzle
from becoming blocked:

place an empty container under the nozzle.

. then turn the function selector (b) to the

position «\!!\.J»again during few seconds.

. turn the function selector (b)to the position

O.

. clean the nozzlewith a damp cloth.

.For thorough cleaning of the nozzle, please

refer to the paragraph «Maintenance».

Notes
Ifyou wish to make an espresso

immediately after steam, the appliance

must first cool down untilit reaches the right
temperature for extraction

.To do this, insert an empty filter holder (no

coffee) in the machine and pOSItion a
suitable container beneath it. Then turn the

function selector (b) to the position «~».

.Let the water run through until the indicator

light (c)goes out. Then, turn the function
selector (b)to the position 0

After this, the machine is now ready once
more to make an espresso (see paragraph

«espresso function»).
Please note: when the appliance isrunning,

and also afterwards, the nozzlewillbe very
hot. Allowtime for the appliance to cool
down to prevent scalding or burning.

Maintenance

.Unplug the appliance and allow it to cool.

.Neverwash the accessoriesfor your espresso

In the dishwasher.

.Clean the body of the appliance with a

damp cloth.

After use, the water tank must be emptied.

. The drip tray (j)

.Each time an espresso is prepared, the drip

tray fills with water. This is perfectly normal.
To prevent any overflow, remove the grid (7)
and empty the drip tray regularly.

.Ifnecessary, clean the dnp tray and the gnd

with water and a littlenon-abrasive
washing-up liquid,rinse and dry.When

replacing, return the plasticblocksituated at

the back of the tray (8)

.The percolation head, the filter holder

and the filters

These must be cleaned after everyuse. Simply
run a damp cloth over the percolation head

and clean the other accessorieswith water

and a smallquantityof non-abrasiveliquid

cleanser. Rinseand dry.

.Ifthe percolation head becomes heavily

encrusted, unscrew itsgrid using a coin,

cleanitand replace,tighteningitfirmly(9).

0 The seal for the percolation head

When you are not using your espresso, do not

leave the filter holder inthe appliance

in order

to prevent wear on the seal.

. Clean the seal regularly using a damp cloth.

0 The steam nozzle (g)

. It must be cleaned with a damp cloth after

every

use.

Please note: it may still be very hot!

For more thorough cleaning, the nozzle may
be taken off (10)

. Unscrew the tip (g1), If necessary using a

coin.

.Separate the various components and clean

them with hot water and a small quantity of
non-abrasive liquid cleanser.Rinseand dry.

. If need be, unblock the tip (g1)using a fine

needle.

Descaling

It is vital that you descaleyour espresso

machine in order to guarantee its continued

operation.

.Descale your espresso at regular intervals

using citric or tartaric acid.

We do, however, advise you to use the Krups

descaling accessory, reference 054, which

is available from approved Krups service
centers. This

accessory includes, in addition to

two doses of descaler, a water hardness test

strip to evaluate the frequency of descaling
for your appliance in normal use. The amount
of scaling depends on the hardness of the

water, but also on how often it is used. The

frequency of descaling indicated by accessory
054 is thus given by way of Indication only.

You must

never, under any Circumstances, use

classic sulfuric acid or other products

containing this acid asthere is a risk of
damaging the appliance. Carefully check the
composition of the descaling products you
intend to use

- Then use the following method:

. Unscrewthe grid of the percolation head

and clean it (9).

. Dissolve2 tablespoons of descaler or one

packet of accessory054 in half a liter (16 oz)
of lukewarm water and pour the mixture
into the empty water tank.

.Set the «on/off» switch (h). The indicator

light (h1) comes on.

Once the appliance reachesthe appropriate
temperature, the temperature control
indicator light (c) comes on.

. Placea container under the percolation

head. Runthrough about 1/3 of the mixture,

setting the function selector (b) to the

position «.1E».

.Set the «on/off» switch (h). The indicator

light (h1)comes off and wait 10 to 15
minutes to allow the descalerto take effect

. Then set the «on/off» switch (h).The

indicator light (h1)comes on.

. With the function selector (b) in the position

«.1E», allowthe remainderof the mixtureto

run into the container placed under the
percolation head.

.Then reset the function selector (b) to O.

.Run two tanks of fresh water through to

rinse the percolation head. Todo this:

. fillthe tank

. placeacontainerunderthe percolation

head, set the function selector (b) to «.1E»
and allow the content of the tank to run

through.

. then set the function selector (b) to O.

.Set the «on/off» switch (h). The indicator

light (h1) comes off

. replacethe grid on the head of the appliance

(see paragraph «Maintenance») (9).

Notes:

In the caseof seriousscaling, soak the grid of
the percolation head for 5 minutes in 1/3 of
the mixture obtained during the first run-

through.

If necessary,this operation can also be

performed with the steam nozzle:

KRUPS11

.Todo thiS, dismantle the nozzleas instructed

inthe paragraph «Maintenance» and soak
the scaled parts for 5 minutes In1/3 of the
mixture obtained duringthe first run-
through. Rinsethe various parts thoroughly
before replacing them

Problems, :likely causes .and
corrective a"Ctions

12

KRUPS

Problems

Probable Corrective

causes actions

Espressonot

Theaccessories

Pre-heatthe

hotenough.

arecold

accessories

(cups,filter Seetheparagraph
andfilterholder)

«Preparingan
espresso»

Theapplianceis

Waitforthe

nothotenough.

indicatorlight
(c)tocomeon

Leakingcoffee

Thefilterholder

Seeparagraph

aroundthefilter

ISnotfitted

«Preparingan

holder

correctly. espresso»
ThereISresidual Cleanaround

coffeeontheedge

thefilterandthe

ofthefilter seal
Thesealofthe Cleantheseal
percolationhead withadamp

ISdirty.

cloth

Thesealof the

Contactan

percolationheadis approvedKRUPS
defective. servicecenter.

Veryloudnoise

NowaterInthe

Fillthetank

pump

comingfromthe
tank.

Tankincorrectly

Pressfirmlyon

fitted. thetank
Groundcoffeetoo

Usefreshly

oldordry groundcoffee.

Waterdoesnot

Nowaterinthe Fillthe

flowproperly.

tank tank
Tankbadly

Pressfirmlyon

fitted. thetank

Waterdoesnot

Thefilteris

Cleanthefilter

flowproperly.

blocked-the

andthegridof

groundcoffeeis thepercolation
toofineor headSeethe

compacted

paragraph

tootightly.

«Maintenance»
andtryuSinga

coarserground
coffee

Gridofthe

Putthegridto

percolationhead

soakInthe

isclogged. descaling

solutionSeethe

paragraph
«Descallng».

Appliancescaled. SeetheParagraph

«Descallng»

Waterpasses

Groundcoffeetoo

Tryafiner

tooqUickly

coarse.

groundcoffee

Insufficientquan- Usethespoon
tyofground

suppliedto

coffee measureoutthe

coffee

Groundcoffeenot

Compactthe

compacted groundcoffee

more

Theespressohas

Groundcoffee

TryuSinga finer

nohead(crema

toocoarse

groundcoffee

on thecoffee)

Groundcoffeenot

Compactthe

compacted

groundcoffee

enough

more
Groundcoffeeold Useafresh
ortoodry.

groundcoffee

Insufficient

SteamIcappuccino

Seeparagraph

foamonmilk. nozzleblocked «Maintenance»

Milktooold

Usefreshmilk

Milkislukewarm.

Coolmilkin
therefrigerator

Residualwater

Groundcoffeenot

Compactthe

Intheground sufficientlycompac-

groundcoffee.

coffee.

ted
Insufficient Increasethe
quantity quantityof

ofgroundcoffee

groundcoffee

Thereiswater

Thedriptray

Emptyit regularly

aroundthe

isoverflowing

appliance.

Limited'One v:ea~V\(arianty

Your KRUPS# FNP1IScovered by the
following warranty:

If within one year from date of purchasethis
KRUPSproduct fails to function becauseof
defects in materials or workmanship, KRUPS
North America will, at its option, repair or
replace the unit without charge, provided the
owner hasa proof of date of purchase.

Thiswarranty will bevoid if malfunction was
caused by damage to the product by accident,
misuse, useon frequency or voltage other
than marked on the product and/or described
in the instructions, abuse including tampering,
damage in transit, or use for commercial
purposes. Thiswarranty givesyou specific
legal rights, and you may also haveother
rights which may vary from state to state.

KRUPS13

- - - - --- - - -u-u -- ----

GUARANTEE OF PERFORMANCE

This fine KRUPS product is manufactured according to a rigid code

of quality standards, and, with minimum care, should give years of
service. However, should the need arise for repairs or for
replacement parts within or after the warranty period, please call

our CONSUMER SERVICEDEPARTMENT:

USA:

[phone]
24-hours a day, 7 days a week

[phone]
Monday-Friday 8:00 a.m - 4:30 p.m

Canada:

You will be provided with specific instruction on how to get your

product repaired.
The department will also be able to answer any general product
questions you may have.

Before calling the Consumer Service Department, please have the
type number of your KRUPSappliance available.
You must have this information before calling our Consumer

Service Department so that we may better answer your questions.
The type number can be located by looking at the bottom of your

appliance.

This product is Type #FNP1

Any general correspondence can be addressed to:

USA:

KRUPS North America, Inc.
P.O.Box 3900

Peoria, IL 61612

Canada: KRUPS Service

20 Caldari Rd
Concord, Ontario
L4K 4N8

14KRUPS