Page 1
INSTALLATION GUIDE
Stainless Steel Farmhouse
Kitchen Sink
KHF200-30 / KHF200-33 / KHF200-36
KHF203-33 / KHF203-36
KHF204-33
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV. September 7, 2018
Page 2
Thank you for your purchase
We would like to take this opportunity to thank you for choosing Kraus.
We hope that you are completely satised with your purchase, and enjoy it for years
to come. If you have any questions, or require technical assistance, please contact
us at 800.775.0703 and one of our representatives will be happy to help.
For more information about Kraus products, please visit:
www.kraususa.com
In order to activate your warranty and get faster access to customer support, please
register your new Kraus product at:
www.kraususa.com/registration
Sincerely,
Kraus USA Customer Service
1
Page 3
Prior to Installation:
• Inspect the sink prior to installation to make sure the sink has not been damaged
during shipping
• Use the cut-out template provided by Kraus
• Observe all plumbing and building codes according to your state requirement
• Additional oor and wall preparation may be required to avoid damaging the
product
• Make sure to purchase the correct cabinet for your farmhouse sink. Farmhouse
base cabinets should be 3” larger than the actual size of the sink
• Not recommended to be installed with laminate countertop
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or Customerservice@kraususa.com
The step-by-step guidelines in the installation instructions are a general reference for installing a
Kraus Sink. Should there be any discrepancies, Kraus cannot be held liable. It is recommended to
install all Kraus products by hiring a licensed professional.
2
Page 4
Tools you will need:
Phillips screwdriver
Adjustable wrench
Phillips screwdriver
Hex wrench
Silicone Sealant
I
D
J
F
B
G
H
E
Safety Goggles
Phillips Screwdriver
Drill
Tape Measure
Silicone Adhesive Jig Saw
Pencil
Screwdriver
Acetone
Level
NOTE: Specialized tools may be necessary to install Kraus Stainless Steel Undermount
sinks with countertop materials other than wood, marble, or granite
Parts List
• Cut-Out Template
• Bottom Grids
• 1 Drain - BST-1 for Single Bowl
• 2 Drains – BST-1 & ST-1 for Double Bowls
3
Page 5
Dimensions
KHF200-30
20-3/4”
527mm
16”
406mm
27”
686mm
29-3/4”
756mm
KHF200-30
527mm
KHF200-33
527mm
254mm
254mm
527mm
KHF203-33
254mm
20-3/4”
527mm
16”
406mm
11-5/8”
295mm
17-3/8”
442mm
32-7/8”
835mm
KHF203-33
527mm
835mm
KHF203-36
16”
27”
686mm
29-3/4”
756mm
9”
KHF200-30
29 3/4” x 20 3/4” x 10”
Min Cabinet Size: 30”
Matching Grid: KBG-200-30
Drain Model #: BST-1
17-3/8”
442mm
32-7/8”
11-5/8”
295mm
406mm
229mm
16”
406mm
20-3/4”
10”
254mm
KHF200-33
32 7/8” x 20 3/4” x 10”
Min Cabinet Size: 33”
Matching Grid: KBG-200-33
Drain Model #: BST-1
20-3/4”
19”
483mm
30”
762mm
32-7/8”
835mm
35-7/8”
911mm
330mm
16”
406mm
20-3/4”
33”
838mm
35-7/8”
911mm
9”
10”
229mm
16”
527mm
406mm
20-3/4”
9”
10”
229mm
254mm
KHF200-36
35 7/8” x 20 3/4” x 10”
Min Cabinet Size: 36”
Matching Grid: KBG-200-36
Drain Model #: BST-1
16”
527mm
406mm
20-3/4”
13”
11-5/8”
295mm
32-7/8”
855mm
17-3/8”
442mm
16”
406mm
20-3/4”
KHF203-33
32 7/8” x 20 3/4” x 10”
Min Cabinet Size: 33”
Matching Grid: KBG-200-33-1
and KBG-200-33-2
Drain Model #: BST-1 & ST-1
9”
9”
10”
229mm
KHF203-36
35 7/8” x 20 3/4” x 10”
Min Cabinet Size: 36”
Matching Grid: KBG-200-36-1
and KBG-200-36-2
Drain Model #: BST-1 & ST-1
9”
10”
229mm
254mm
KHF204-33
32 7/8” x 20 3/4” x 10”
Min Cabinet Size: 33”
Matching Grid: KBG-204-33-1
and KBG-204-33-2
Drain Model #: BST-1 & ST-1
229mm
10”
4
Page 6
1. Measure & Build Supports
• Measure the actual height of apron
• Build supports on inside of cabinet based on sink measurements
Installer Tip: Support Options
• 1 ¼” Angle Irons
• (2) 2”x 4’
• 3/4” Plywood
SUPPORTS
5
Page 7
2. Cut Cabinet Front
• Measure height of apron front. Add 1/16” to the dimension when you
mark base cabinet front cutout. Use jigsaw to cut
6
Page 8
3. Install Sink
• Place sink in opening. The weight of sink should be sustained
by the built supports
• Make sure sink is leveled from front to back and side to side
• Uses silicone to ll in gaps where necessary
7
Page 9
4. Cut Countertop
• Use a bead of silicone (or preferred adhesive) around the rim of the
sink. Check the alignment of the sink to the cutout in the countertop.
Place countertop cutout hole over sink and press rmly
Installer Tip: Use acetone or denatured alcohol to remove any excess
sealant
Silicone Adhesive
8
Page 10
5. Installing Plumbing Fixtures
• Connect drain, trap to drain and water supply connections to the
faucet according to manufacturer’s instruction.
• Run water into sink and check for leaks
9
Page 11
Codes/Standards Applicable:
HELP LINE
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com
If you are a HOMEOWNER please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
Customerservice@kraususa.com
If you are a PLUMBING CONTRACTOR OR TRADE PROFESSIONAL please contact a Kraus
Pro Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
Proservice@kraususa.com
If you are an AUTHORIZED PARTNER please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
Partnersupport@kraususa.com
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
10
Page 12
IMPORTANT
Register Your Kraus Product
Activate Your Warranty
Access Premium Customer Support
Get Product Information
REGISTER TODAY
http://www.kraususa.com/registration
www.kraususa.com
Loading...