Kontron CP-RIO6-A216 User Manual

Page 1
» User Guide «
CP-RIO6-A CP-RIO6-B
CP-RIO6-A216 CP-RIO6-B216
6U CompactPCI Rear Transition Modules
Doc. ID: 1030-8996, Rev. 2.0
Ma y 11, 2011
P R E L I M I N A R Y
If it’s embedded, it’s Kontron.
Page 2
Revision History
Publication Title: CP-RIO6-A/CP-RIO6-B/CP-RIO6-A216/CP-RIO6-B216
6U CompactPCI Rear Transition Modules
Doc. ID: 1030-8996
Rev. Brief Description of Changes Date of Issue
1.0 Initial issue 4-Jun-2009
1.1 General update, changes to Chapter 2.1.7, HD Audio Interfaces 10-Sep-2009
2.0 General update 11-May-2011
Imprint
Kontron Modular Computers GmbH may be contacted via the following:
MAILING ADDRESS TELEPHONE AND E-MAIL
Kontron Modular Computers GmbH +49 (0) 800-SALESKONTRON Sudetenstraße 7 sales@kontron.com D - 87600 Kaufbeuren Germany
P R E L I M I N A R Y
For further information about other Kontron products, please visit our Internet website: www.kontron.com.
Disclaimer
Copyright © 201 1 Kontron AG. All righ ts reserved. All dat a is for information purposes only and not guaranteed for legal purposes. Information has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Kontron and the Kontron logo and all other trademarks or registered trademarks are the property of their respective own­ers and are recognized. Specifications are subject to change without notice.
Page ii ID 1030-8996, Rev. 2.0
Page 3
CP-RIO6-Ax/Bx Preface
Table of Contents
Revision History .........................................................................................................ii
Imprint ........................................................................................................................ii
Disclaimer ..................................................................................................................ii
Table of Contents ......................................................................................................iii
List of Tables ..............................................................................................................v
List of Figures ..........................................................................................................vii
Proprietary Note ........................................................................................................ix
Trademarks ...............................................................................................................ix
Environmental Protection Statement .........................................................................ix
Explanation of Symbols .............................................................................................x
For Your Safety .........................................................................................................xi
High Voltage Safety Instructions ...........................................................................xi
Special Handling and Unpacking Instructions ......................................................xi
General Instructions on Usage ................................................................................xii
Two Year Warranty ..................................................................................................xiii
1. Introduction ............................................................................. 1 - 3
1.1 Board Overview .......................................................................................1 - 3
1.2 CP-RIO6-Ax/Bx Feature Comparison .....................................................1 - 3
1.3 Board Diagrams ......................................................................................1 - 4
1.3.1 Functional Block Diagrams .............................................................1 - 4
1.3.2 Front Panels ...................................................................................1 - 6
1.3.3 Board Layout ..................................................................................1 - 7
1.4 Technical Specification .......................................................................... 1 - 11
1.5 Standards ..............................................................................................1 - 13
1.6 Related Publications .............................................................................1 - 14
2. Functional Description ........................................................... 2 - 3
2.1 Board Interfaces ......................................................................................2 - 3
2.1.1 USB Interfaces ................................................................................2 - 3
2.1.1.1 Front Panel USB 2.0 Interface ...............................................2 - 3
P R E L I M I N A R Y
2.1.1.2 Onboard USB 2.0 NAND Flash Interface ...............................2 - 4
2.1.2 COM Interfaces ...............................................................................2 - 5
ID 1030-8996, Rev. 2.0 Page iii
Page 4
2.1.3 VGA Interface ..................................................................................2 - 7
2.1.4 DVI-D Interface ...............................................................................2 - 8
2.1.5 HDMI Interface ................................................................................2 - 9
2.1.6 Gigabit Ethernet Interfaces ...........................................................2 - 10
2.1.7 HD Audio Interfaces ......................................................................2 - 11
2.1.7.1 HD Audio Specifications ......................................................2 - 11
2.1.7.2 Mic-In, Line-In and Line-Out Interfaces ................................2 - 13
2.1.7.3 S/P-DIF-Out Interface ...........................................................2 - 13
2.1.7.4 CD-In Interface .....................................................................2 - 13
2.1.7.5 Internal Line-Out Mono Interface ..........................................2 - 13
2.1.8 FAN Connectors ............................................................................2 - 14
2.1.9 Serial ATA Interfaces .....................................................................2 - 14
2.1.10 Rear I/O Interface on CompactPCI Connectors rJ3, rJ4 and rJ5 ..2 - 15
2.1.10.1 States of ID Bits ....................................................................2 - 17
3. Installation ................................................................................3 - 3
3.1 Safety Requirements ...............................................................................3 - 3
3.2 Initial Installation Procedures ...................................................................3 - 4
3.3 Standard Removal Procedures ................................................................3 - 5
3.4 Installation of Peripheral Devices ............................................................3 - 5
3.4.1 USB Device Installation ...................................................................3 - 5
3.4.2 USB 2.0 NAND Flash Module Installation .......................................3 - 6
3.4.3 Installation of External Serial ATA Devices .....................................3 - 6
P R E L I M I N A R Y
Page iv ID 1030-89 96, Rev. 2.0
Page 5
CP-RIO6-Ax/Bx Preface
List of Tables
1-1 CP-RIO6-Ax/Bx Feature Comparison ........................................................ 1 - 3
1-2 CP-RIO6-Ax/Bx Main Specifications ....................................................... 1 - 11
1-3 Standards for the CP-RIO6-Ax/Bx ........................................................... 1 - 13
1-4 Related Publications ................................................................................ 1 - 14
2-1 USB Connectors J17 and J18 Pinout ........................................................ 2 - 3
2-2 USB NAND Flash Connectors J7 and J11 Pinout ..................................... 2 - 4
2-3 Serial Port Connector J20 (COM1) Pinout (RS-232) ................................. 2 - 5
2-4 Serial Port Connector J6 (COM2) Pinout (RS-232/RS-422) ...................... 2 - 6
2-5 D-Sub VGA Connector J22 Pinout ............................................................ 2 - 7
2-6 DVI Connector J23 Pinout ......................................................................... 2 - 8
2-7 HDMI Connector J21 Pinout ...................................................................... 2 - 9
2-8 Pinout of GbE Connector J19A/B ............................................................ 2 - 10
2-9 HD Audio Specifications .......................................................................... 2 - 11
2-10 CD-In Connector J14 Pinout .................................................................... 2 - 13
2-11 Internal Line-Out Mono Connector J10 Pinout ........................................ 2 - 13
2-12 Fan Control Connectors J1 and J2 Pinout ............................................... 2 - 14
2-13 SATA Connectors J8, J9, J12 and J13 Pinout ......................................... 2 - 14
2-14 Rear I/O CompactPCI Rear I/O Connector rJ3 Pinout ............................ 2 - 16
2-15 Rear I/O CompactPCI Rear I/O Connector rJ3 Signals ........................... 2 - 17
2-16 Bit ID1 States ........................................................................................... 2 - 17
2-17 Bits ID4 and ID3 States ........................................................................... 2 - 17
2-18 Rear I/O CompactPCI Rear I/O Connector rJ4 Pinout ............................ 2 - 18
2-19 Rear I/O CompactPCI Rear I/O Connector rJ5 Pinout ............................ 2 - 19
2-20 Rear I/O CompactPCI Rear I/O Connector rJ5 Signals ........................... 2 - 20
P R E L I M I N A R Y
ID 1030-8996, Rev. 2.0 Page v
Page 6
This page has been intentionally left blank.
P R E L I M I N A R Y
Page vi ID 1030-8996, Rev. 2.0
Page 7
CP-RIO6-Ax/Bx Preface
List of Figures
1-1 CP-RIO6-A/CP-RIO6-A216 Functional Block Diagram ........................... 1 - 4
1-2 CP-RIO6-B/CP-RIO6-B216 Functional Block Diagram ........................... 1 - 5
1-3 CP-RIO6-Ax/Bx Front Panels .................................................................. 1 - 6
1-4 CP-RIO6-A Board Layout – Front View ................................................... 1 - 7
1-5 CP-RIO6-A216 Board Layout – Front View ............................................. 1 - 8
1-6 CP-RIO6-B Board Layout – Front View ................................................... 1 - 9
1-7 CP-RIO6-B216 Board Layout – Front View ........................................... 1 - 10
2-1 USB Connectors J17 and J18 .................................................................. 2 - 3
2-2 USB NAND Flash Connectors J7 and J11 ............................................... 2 - 4
2-3 Serial Port Connector J20 (COM1) .......................................................... 2 - 5
2-4 Serial Port Connector J6 (COM2) ............................................................ 2 - 6
2-5 D-Sub VGA Connector J22 ...................................................................... 2 - 7
2-6 DVI Connector J23 ................................................................................... 2 - 8
2-7 HDMI Connector J21 ............................................................................... 2 - 9
2-8 Gigabit Ethernet Connectors J19A/B ..................................................... 2 - 10
2-9 Triple Audio Jack 16 ............................................................................... 2 - 13
2-10 S/P-DIF-Out Connector 15 ..................................................................... 2 - 13
2-11 CD-In Connector J14 ............................................................................. 2 - 13
2-12 Internal Line-Out Mono Connector J10 ................................................. 2 - 13
2-13 Fan Control Connectors J1 and J2 ........................................................ 2 - 14
2-14 SATA Connectors J8, J9, J12 and J13 .................................................. 2 - 14
2-15 Rear I/O CompactPCI Connectors rJ3, rJ4 and rJ5 .............................. 2 - 15
P R E L I M I N A R Y
ID 1030-8996, Rev. 2.0 Page vii
Page 8
This page has been intentionally left blank.
P R E L I M I N A R Y
Page viii ID 1030-8996, Rev. 2.0
Page 9
CP-RIO6-Ax/Bx Preface
Proprietary Note
This document contains information proprietary to Kontron. It may not be copied or transmitted by any means, disclosed to others, or stored in any retrieval system or media without the prior written consent of Kontron or one of its authorized agents.
The information contained in this document is, to the best of our knowledge, entirely correct. However, Kontron cannot accept liability for any inaccuracies or the consequences thereof, or for any liability arising from the use or application of any circuit, product, or example shown in this document.
Kontron reserves the right to change, modify, or improve this document or the product described herein, as seen fit by Kontron without further notice.
Trademarks
Kontron, the PEP logo and, if occurring in this manual, “CXM” are trademarks owned by Kon­tron, Kaufbeuren (Germany). In addition, this document may include names, company logos and trademarks, which are registered trademarks and, therefore, proprietary to their respective owners.
Environmental Protection Statement
This product has been manufactured to satisfy environmental protection requirements where possible. Many of the components used (structural parts, printed circuit boards, connectors, batteries, etc.) are capable of being recycled.
Final disposition of this product after its service life must be accomplished in accordance with applicable country, state, or local laws or regulations.
P R E L I M I N A R Y
ID 1030-8996, Rev. 2.0 Page ix
Page 10
Explanation of Symbols
Caution, Electric Shock!
This symbol and title warn of hazards due to electrical shocks (> 60V) when touching products or parts of them. Failure to observe the pre­cautions indicated and/or prescribed by the law may endanger your life/health and/or result in damage to your material.
Please refer also to the section “High Voltage Safety Instructions” on the following page.
Warning, ESD Sensitive Device!
This symbol and title inform that electronic boards and their compo­nents are sensitive to static electricity. Therefore, care must be taken during all handling operations and inspections of this product, in order to ensure product integrity at all times.
Please read also the section “Special Handling and Unpacking Instructions” on the following page.
Warning!
This symbol and title emphasize points which, if not fully understood and taken into consideration by the reader, may endanger your health and/or result in damage to your material.
Note ...
This symbol and title emphasize aspects the reader should read through carefully for his or her own advantage.
P R E L I M I N A R Y
Page x ID 1030-8996, Rev. 2.0
Page 11
CP-RIO6-Ax/Bx Preface
For Your Safety
Y our new Kontron product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation. Therefore, in the interest of your own safety and of the correct operation of your new Kontron product, you are requested to conform with the following guidelines.
High Voltage Safety Instructions
Warning!
All operations on this device must be carried out by sufficiently skilled personnel only.
Caution, Electric Shock!
Before installing a not hot-swappable Kontron product into a system always ensure that your mains power is switched off. This applies also to the installation of piggybacks.
Serious electrical shock hazards can exist during all installation, repair and maintenance operations with this product. Therefore, always unplug the power cable and any other cables which provide external voltages before performing work.
Special Handling and Unpacking Instructions
ESD Sensitive Device!
Electronic boards and their components are sensitive to static elec­tricity. Therefore, care must be taken during all handling operations and inspections of this product, in order to ensure product integrity at all times.
Do not handle this product out of its protective enclosure while it is not used for operational purposes unless it is otherwise protected.
P R E L I M I N A R Y
Whenever possible, unpack or pack this product only at EOS/ESD safe work stations. Where a safe work station is not guaranteed, it is important for the user to be electrically discharged before touching the product with his/her hands or tools. This is most easily done by touching a metal part of your system housing.
It is particularly important to observe standard anti-static precautions when changing piggy­backs, ROM devices, jumper settings etc. If the product contains batteries for RTC or memory backup, ensure that the board is not placed on conductive surfaces, including anti-static plas­tics or sponges. They can cause short circuits and damage the batteries or con ductive circuit s on the board.
ID 1030-8996, Rev. 2.0 Page xi
Page 12
General Instructions on Usage
In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or modifications to the device, which are not explicitly approved by Kontron and described in this manual or received from Kontron’s Technical Support as a special handling instruction, will void your warranty.
This device should only be installed in or connected to systems that fulfill all necessary technical and specific environmental requirements. This applies also to the operational temperature range of the specific board version, which must not be exceeded. If batteries are present, their temperature restrictions must be taken into account.
In performing all necessary installation and application operations, please follow only the instructions supplied by the present manual.
Keep all the original packaging material for future storage or warranty shipments. If it is necessary to store or ship the board, please re-pack it as nearly as possible in the manner in which it was delivered.
Special care is necessary when handling or unp acking the product. Please co nsult the special handling and unpacking instruction on the previous page of this manual.
P R E L I M I N A R Y
Page xii ID 1030-8996, Rev. 2.0
Page 13
CP-RIO6-Ax/Bx Preface
Two Year Warranty
Kontron grants the original purchaser of Kontron’s products a TWO YEAR LIMITED HARDWARE
WARRANTY
implied by anyone on behalf of Kontron are valid unless the consumer has the expre ss written consent of Kontron.
Kontron warrants their own products, excluding software, to be free from manufacturing and material defects for a period of 24 consecutive months from the date of purchase. This warranty is not transferable nor extendible to cover any other users or long-term storage of the product. It does not cover products which have been modified, altered or repaired by any other party than Kontron or their authorized agents. Furthermore, any product which has been, or is sus­pected of being damaged as a result of negligence , improper use, incorrect handling, servicing or maintenance, or which has been damaged as a result of excessive current/voltage or tem­perature, or which has had its serial number(s), any ot her markings or parts thereof altered, de­faced or removed will also be excluded from this warranty.
If the customer’s eligibility for warranty has not been voided, in the event of any claim, he may return the product at the earliest possible convenience to the original place of p urchase, togeth­er with a copy of the original document of purchase, a full description of the application the product is used on and a description of the defect. Pack the product in such a way as to ensure safe transportation (see our safety instructions).
as described in the following. However , no other warranties that may be granted or
Kontron provides for repair or replacement of any p art, assembly or su b-assembly at their own discretion, or to refund the original cost of purchase, if appropriate. In the event of repair, re­funding or replacement of any part, the ownership of the removed or replaced parts reverts to Kontron, and the remaining part of the original guarantee, or any new guarantee to cover the repaired or replaced items, will be transferred to cover the new or repaired items. Any exten­sions to the original guarantee are considered gestures of goodwill, and will be defined in the “Repair Report” issued by Kontron with the repaired or replaced item.
Kontron will not accept liability for any further claims resulting directly or indirectly from any warranty claim, other than the above specified repair, replacement or refunding. In particular, all claims for damage to any system or process in which the product was employed, or any loss incurred as a result of the product not functioning at any given time, are excluded. The extent of Kontron liability to the customer shall not exceed the original purchase price of the item for which the claim exists.
Kontron issues no warranty or representation, either explicit or implicit, with respect to its products’ reliability, fitness, quality, marketability or ability to fulfil any particular application or purpose. As a result, the products are sold “as is,” and the responsibility to ensure their suitability for any given task remains tha t of the purchaser. In no event will Kontron be liable for direct, indirect or consequential damages resulting from the use of our hardware or software products, or documentation, even if Kon tron were advised of the possibility of such claims prior to the purchase of the product or during any period since the date of its purchase.
Please remember that no Kontron employee, dealer or agent is authorized to make any modification or addition to the above specified terms, either verbally o r in any other form, written or electronically transmitted, without the company’s consent.
P R E L I M I N A R Y
ID 1030-8996, Rev. 2.0 Page xiii
Page 14
This page has been intentionally left blank.
P R E L I M I N A R Y
Page xiv ID 1030-8996, Rev. 2.0
Page 15
CP-RIO6-Ax/Bx Introduction
Chapter 1
1
Introduction
ID 1030-8996, Rev. 2.0 Page 1 - 1
P R E L I M I N A R Y
Page 16
Introduction CP-RIO6-Ax/Bx
This page has been intentionally left blank.
P R E L I M I N A R Y
Page 1 - 2 ID 1030-8996, Rev. 2.0
Page 17
CP-RIO6-Ax/Bx Introduction
1. Introduction
1.1 Board Overview
The CP-RIO6-Ax/Bx 6U CompactPCI rear transition module has been designed for use with Kontron 6U CompactPCI CPU boards and provides comprehensive rear I/O functionality for peripherals. In order to use the CP-RIO6-Ax/Bx, a special 6U CompactPCI backplane with rear I/O support as well as a compatible and correctly configured CPU board are required.
There are four modules described in this user guide: CP-RIO6-A, CP-RIO6-A216, CP-RIO6-B, and CP-RIO6-B216. All four modules provide various data, communication and multimedia in­terfaces as well as support for two optional USB 2.0 NAND Flash modules and four external SATA devices. The CP-RIO6-Ax/Bx comes with four USB 2.0 ports, four onboard SATA ports, two COM ports, and an HD audio codec supporting five audio ports such as one onboard CD­In port, one Mic-In port, one Line-In port, one Line-Out port, and one S/P-DIF-Out port. Further­more, the CP-RIO6-A and the CP-RIO6-A216 are equipped with one VGA (CRT) port on the front panel. The CP-RIO6-B and the CP-RIO6-B216 provide a DVI-D port and a HDMI port on the front panel. In addition, the CP-RIO6-A and the CP-RIO6-B are equipped with two Gigabit Ethernet ports on the front panel. The CP-RIO6-Ax/Bx has three CompactPCI connectors for connecting the CP-RIO6-Ax/Bx to the backplane.
1.2 CP-RIO6-Ax/Bx Feature Comparison
The following table provides a feature comparison of the CP-RIO6-Ax/Bx.
Table 1-1: CP-RIO6-Ax/Bx Feature Comparison
PORT CP-RIO6-A CP-RIO6-A216 CP-RIO6-B CP-RIO6-B216
VGA x x -- -­DVI-D -- -- x x HDMI -- -- x x 2x GbE x -- x -­COM1 xxxx 2x USB 2.0 x x x x Mic-In xxxx
Front Panel Ports
Line-In x x x x Line-Out x x x x S/P-DIF-Out xxxx COM2 xxxx 2x USB 2.0 NAND Flash x x x x
P R E L I M I N A R Y
4x SATA xxxx CD-In x x x x
Onboard Ports
Internal Line-Out Mono x x x x 2x FAN xxxx
ID 1030-8996, Rev. 2.0 Page 1 - 3
Page 18
Introduction CP-RIO6-Ax/Bx
xxx
xxx
Onboard Connector
Front Panel Connector
CPCI
Connectors
rJ3
rJ4
rJ5
SATA
Connector
S
A
T
A
xxx
Controller / Driver
HD A
udio
HD
Audio
Codec
S/P-DIF
Out
Line-In
Line-
Out
Mic-In
CD-In
Stereo output
Digital output
Stereo input
Stereo input
Stereo input
R
S
-
2
3
2
V
G
A
VGA
COM1
SATA
Connector
S
A
T
A
SATA
Connector
S
A
T
A
SATA
Connector
S
A
T
A
2x GbE
2x Mag
2
x
E
t
h
e
r
n
e
t
2
x
E
t
h
USB NAND
Flash
USB NAND
Flash
2x USB2.0
USB
U
S
B
U
S
B
COM2
(10-pin)
S
e
r
i
a
l
FAN1 FAN2
Sense
Not available on the CP-RIO6-A216
Mono output
Internal
Line-Out
1.3 Board Diagrams
The following diagrams provide additional information concerning the boards’ functionality and component layout.
1.3.1 Functional Block Diagrams
Figure 1-1: CP-RIO6-A/CP-RIO6-A216 Functional Block Diagram
P R E L I M I N A R Y
Page 1 - 4 ID 1030-8996, Rev. 2.0
Page 19
CP-RIO6-Ax/Bx Introduction
xxx
xxx
Onboard Connector
Front Panel Connector
CPCI
Connectors
rJ3
rJ4
rJ5
SATA
Connector
D
V
I
-
D
S
A
T
A
xxx
Controller / Driver
H
DMI
HDMI
DVI
HD Audio
HD
Audio
Codec
S/P-DIF
Out
Line-In
Line-Out
Mic-In
CD-In
Stereo output
Digital output
Stereo input
Stereo input
Stereo input
RS-232
COM1
SATA
Connector
S
A
T
A
SATA
Connector
S
A
T
A
SATA
Connector
S
A
T
A
2x GbE
2x Mag
2
x
E
t
h
e
r
n
e
t
2
x
E
t
h
USB NAND
Flash
USB NAND
Flash
2x USB2.0
2x USB
U
S
B
U
S
B
COM2
(10-pin)
S
e
r
i
a
l
FAN1 FAN2
Sense
Not available on the CP-RIO6-B216
Mono output
Internal
Line-Out
Figure 1-2: CP-RIO6-B/CP-RIO6-B216 Functional Block Diagram
P R E L I M I N A R Y
ID 1030-8996, Rev. 2.0 Page 1 - 5
Page 20
Introduction CP-RIO6-Ax/Bx
CP-RIO6-A CP-RIO6-A216 CP-RIO6-B CP-RIO6-B216
1.3.2 Front Panels
Figure 1-3: CP-RIO6-Ax/Bx Front Panels
P R E L I M I N A R Y
Page 1 - 6 ID 1030-8996, Rev. 2.0
Page 21
CP-RIO6-Ax/Bx Introduction
rJ3
rJ5
rJ4
GbE
A
GbE
B
J19
J18
USB
J17
J16
Mic-
In
Line-
In
J15
S/P­DIF Out
Magn.
Magn.
Line-
Out
J7
USB
NAND
Flash
12
10
9
J11
1 210
9
1 2
9
1
1
1
USB NAND Flash
1717
1717
10
J12
SATA
J8
SATA
J9
SATA
J13
SATA
J22
VGA
J6
COM2
J20
COM1
CD-In
J14
J2
FAN1
J1
FAN2
2
1
Internal
Line-Out
Mono
J10
1.3.3 Board Layout
Figure 1-4: CP-RIO6-A Board Layout – Front View
P R E L I M I N A R Y
ID 1030-8996, Rev. 2.0 Page 1 - 7
Page 22
Introduction CP-RIO6-Ax/Bx
rJ3
rJ5
rJ4
J18
USB
J17
J16
Mic-
In
Line-
In
J15
S/P-
DIF Out
Line-
Out
J7
USB
NAND
Flash
12
10
9
J11
1 210
9
1 2
9
1
1
1
USB NAND Flash
1717
1717
10
J12
SATA
J8
SATA
J9
SATA
J13
SATA
J22
VGA
J6
COM2
J20
COM1
CD-In
J14
J2
FAN1
J1
FAN2
21
J10
Internal
Line-Out
Mono
Figure 1-5: CP-RIO6-A216 Board Layout – Front View
P R E L I M I N A R Y
Page 1 - 8 ID 1030-8996, Rev. 2.0
Page 23
CP-RIO6-Ax/Bx Introduction
rJ3
rJ5
rJ4
GbE
A
GbE
B
J19
J18
USB
J17
J16
Mic-
In
Line-
In
J15
S/P-
DIF Out
Magn.
Magn.
Line-
Out
J7
USB
NAND
Flash
12
10
9
J11
1 210
9
1 2
9
1
1
1
USB NAND Flash
1717
1717
10
J12
SATA
J8
SATA
J9
SATA
J13
SATA
J23 DVI
J6
COM2
J20
COM1
CD-In
J14
J2
FAN1
J1
FAN2
J21
HDMI
21
J10
Internal
Line-Out
Mono
Figure 1-6: CP-RIO6-B Board Layout – Front View
P R E L I M I N A R Y
ID 1030-8996, Rev. 2.0 Page 1 - 9
Page 24
Introduction CP-RIO6-Ax/Bx
rJ3
rJ5
rJ4
J18
USB
J17
J16
Mic-
In
Line-
In
J15
S/P-
DIF Out
Line-
Out
J7
USB
NAND
Flash
12
10
9
J11
1 210
9
1 2
9
1
1
1
USB NAND Flash
1717
1717
10
J12
SATA
J8
SATA
J9
SATA
J13
SATA
J23 DVI
J6
COM2
J20
COM1
CD-In
J14
J2
FAN1
J1
FAN2
J21
HDMI
21
J10
Internal
Line-Out
Mono
Figure 1-7: CP-RIO6-B216 Board Layout – Front View
P R E L I M I N A R Y
Page 1 - 10 ID 1030-8996, Rev. 2.0
Page 25
CP-RIO6-Ax/Bx Introduction
1.4 Technical Specification
Table 1-2: CP-RIO6-Ax/Bx Main Specifications
CP-RIO6-Ax/Bx SPECIFICATIONS
VGA (CP-RIO6-A, CP-RIO6-A216)
DVI-D (CP-RIO6-B, CP-RIO6-B216)
HDMI (CP-RIO6-B, CP-RIO6-B216)
Ethernet (CP-RIO6-A, CP-RIO6-B)
COM1 One serial RS-232 port on a 9-pin, D-Sub connector, J20 USB Two USB 2.0 interfaces on type A connectors, J17 and J18
Front Panel Interfaces
HD Audio AD1884A HD audio codec supporting the following ports:
One VGA interface on a 15-pin, D-Sub connector, J22, for connecting a standard analog monitor
One DVI-D interface (digital only) on a 29-pin DVI connector, J23, for connecting a monitor with a DVI-D interface
One HDMI interface on a 19-pin HDMI connector, J21, for connecting a monitor with a HDMI interface
Two Gigabit Ethernet interfaces implemented as a dual RJ-45 connector, J19A/B
Mic-In stereo port on a 3.5 mm stereo jack (pink), J16
Line-In stereo port on a 3.5 mm stereo jack (blue), J16
Line-Out stereo port on a 3.5 mm stereo jack (green), J16
S/P-DIF-Out digital port on an optical fiber connector (Toslink), J15
The CP-RIO6-Ax/Bx provides no audio jack detection support.
SATA Four SATA I interfaces implemented as onboard connectors, J8, J9, J12
and J13, for connecting external SATA devices via a SATA cable
USB Two onboard connectors, J7 and J11, for connecting two USB 2.0 NAND
Flash modules COM2 One onboard serial port implemented as a 10-pin, 2.54 mm connector, J6 HD Audio AD1884A HD audio codec supporting the following ports:
CD-In stereo port on a 4-pin onboard connector, J14
Internal line-out mono port on a 2-pin onboard connector, J10
Onboard Interfaces
Fan Two fan connectors, J1 and J2, with PWM control and sense inputs for
monitoring the fan speed. CompactPCI Three CompactPCI connectors, rJ3, rJ4 and rJ5, for connecting the CP-
RIO6-Ax/Bx to the backplane
P R E L I M I N A R Y
ID 1030-8996, Rev. 2.0 Page 1 - 11
Page 26
Introduction CP-RIO6-Ax/Bx
Note ...
When additional components are installed, refer to their operational specifications as this will influ­ence the modules’ operational and storage tem­perature.
Table 1-2: CP-RIO6-Ax/Bx Main Specifications (Continued)
CP-RIO6-Ax/Bx SPECIFICATIONS
Temperature Range Operational: 0°C to +60°C Standard
-40°C to +85°C E2 (optional)
Storage: -55°C to +85°C Without any additional components
MTBF 750253 h (MIL-HDBK-217 FN2, Ground Benign 30°)
General
Mechanical 6U, 4HP, CompactPCI-compliant form factor Dimensions 233.35 mm x 80 mm
1262748 h (Bellcore Issue 6, Ground Benign 30°)
Board Weight CP-RIO6-A: 227 g (without USB NAND Flash module)
CP-RIO6-A216: 223 g (without USB NAND Flash module) CP-RIO6-B: 231 g (without USB NAND Flash module) CP-RIO6-B216: 227 g (without USB NAND Flash module)
P R E L I M I N A R Y
Page 1 - 12 ID 1030-8996, Rev. 2.0
Page 27
CP-RIO6-Ax/Bx Introduction
1.5 Standards
The CP-RIO6-Ax/Bx complies with the requirements of the following standards:
Table 1-3: Standards for the CP-RIO6-Ax/Bx
TYPE ASPECT STANDARD REMARKS
CE Emission EN55022
EN61000-6-3
Immission EN55024
EN61000-6-2
Electrical Safety EN60950-1 --
Mechanical Mechanical Dimen-
sions
Environmental Climatic Humidity IEC60068-2-78 93% RH at 40°C, non-condensing
WEEE Directive 2002/96/EC Waste electrical and electronic equipment RoHS Directive 2002/95/EC Restriction of the use of certain hazardous
Vibration (Sinusoidal)
Single Shock IEC61131-2
IEEE 1101.10 --
IEC61131-2 IEC60068-2-6
IEC60068-2-27
--
--
substances in electrical and electronic equipment
Test parameters:
• 5-150 (Hz) frequency range
• 1 (g) acceleration
• 1 (oct/min) sweep rate
• 10 cycles/axis
• 3 axes Test parameters:
• 15 (g) acceleration
• 11 (ms) pulse duration
• 3 shocks per direction
• 6 directions
• 5 (s) recovery time
Note ...
Kontron performs comprehensive environmental testing of it s products in accor­dance with applicable standards.
Customers desiring to perform further environmental testing of Kontron prod­ucts must contact Kontron for assistance prior to performing any such testing. This is necessary, as it is possible that environmental testing can be destructive when not performed in accordance with the applicable specifications.
In particular, for example, boards without conformal coating must not be exposed to a change of temperature exceeding 1K/ minute, averaged over a period of not more than five minutes. Otherwise, condensation may cause irre­versible damage, especially when the board is powered up again.
Kontron does not accept any responsibility for damage to products resulting from destructive environmental testing.
ID 1030-8996, Rev. 2.0 Page 1 - 13
P R E L I M I N A R Y
Page 28
Introduction CP-RIO6-Ax/Bx
1.6 Related Publications
The following publications contain information relating to the CP-RIO6-Ax/Bx.
Table 1-4: Related Publications
PRODUCT PUBLICATION
CompactPCI Systems and Boards
HD Audio Intel’s High Definition Audio Specification, Rev. 1.0, April 15, 2004 All Kontron products Product Safety and Implementation Guide, ID 1021-9142
CompactPCI Specification 2.0, Rev. 3.0 CompactPCI Packet Switching Backplane Specification PICMG 2.16 Rev. 1.0
(CP-RIO6-A216, CP-RIO6-B216) Kontron CompactPCI Backplane Manual, ID 24229
P R E L I M I N A R Y
Page 1 - 14 ID 1030-8996, Rev. 2.0
Loading...