Page 1
» User Guide «
CP-RIO6-001
CP-RIO6-001-HD
CP-RIO6-001-HD-216
6U CompactPCI Rear Transition Modules
Doc. ID: 1043-5620, Rev. 1.0
December 7, 2010
P R E L I M I N A R Y
If it’s embedded, it’s Kontron.
Page 2
Preface CP-RIO6-001/-HD/-HD-216
Revision History
Publication Title: CP-RIO6-001/CP-RIO6-001-HD/CP-RIO6-001-HD216
6U CompactPCI Rear Transition Modules
Doc. ID: 1043-5620
Rev. Brief Description of Changes Date of Issue
1.0 Initial issue 7-Dec-2010
Imprint
Kontron Modular Computers GmbH may be contacted via the following:
MAILING ADDRESS TELEPHONE AND E-MAIL
Kontron Modular Computers GmbH +49 (0) 800-SALESKONTRON
Sudetenstraße 7 sales@kontron.com
D - 87600 Kaufbeuren Germany
P R E L I M I N A R Y
For further information about other Kontron products, please visit our Internet web site:
www.kontron.com.
Disclaimer
Copyright © 2010 Kontron AG. All rights reserve d. All data is for information purposes only and
not guaranteed for legal purposes. Information has been carefully checked and is believed to
be accurate; however, no responsibility is assumed for inaccuracies. Kontron and the Kontron
logo and all other trademarks or registered trademarks are the property of their respective owners and are recognized. Specifications are subject to change without notice.
Page ii ID 1043-5620, Rev. 1.0
Page 3
CP-RIO6-001/-HD/-HD-216 Preface
Table of Contents
Revision History .........................................................................................................ii
Imprint ........................................................................................................................ii
Disclaimer ..................................................................................................................ii
Table of Contents ......................................................................................................iii
List of Tables ..............................................................................................................v
List of Figures ..........................................................................................................vii
Proprietary Note ........................................................................................................ix
Trademarks ...............................................................................................................ix
Environmental Protection Statement .........................................................................ix
Explanation of Symbols .............................................................................................x
For Your Safety .........................................................................................................xi
High Voltage Safety Instructions ...........................................................................xi
Special Handling and Unpacking Instructions ......................................................xi
General Instructions on Usage ................................................................................xii
Two Year Warranty ..................................................................................................xiii
1. Introduction ............................................................................. 1 - 3
1.1 Board Overview .......................................................................................1 - 3
1.2 CP-RIO6-001/-HD/-HD-216 Feature Comparison ...................................1 - 3
1.3 Board Diagrams ......................................................................................1 - 4
1.3.1 Functional Block Diagrams .............................................................1 - 4
1.3.2 Front Panels ...................................................................................1 - 6
1.3.3 Board Layout ..................................................................................1 - 7
1.4 Technical Specification ..........................................................................1 - 10
1.5 Standards ..............................................................................................1 - 12
1.6 Related Publications .............................................................................1 - 13
2. Functional Description ........................................................... 2 - 3
2.1 Board Interfaces ......................................................................................2 - 3
2.1.1 USB Interfaces ................................................................................2 - 3
2.1.1.1 Front Panel USB Connectors J6 and J7 ................................ 2 - 3
P R E L I M I N A R Y
2.1.1.2 Onboard USB NAND Flash Connector J17 ...........................2 - 4
2.1.2 Digital Video Interfaces ...................................................................2 - 5
ID 1043-5620, Rev. 1.0 Page iii
Page 4
Preface CP-RIO6-001/-HD/-HD-216
2.1.3 Gigabit Ethernet Interfaces .............................................................2 - 6
2.1.4 Serial ATA Interfaces .......................................................................2 - 7
2.1.4.1 SATA Connector J17 ..............................................................2 - 7
2.1.4.2 SATA Connector J19 (optional) ..............................................2 - 8
2.1.5 COM Interfaces ...............................................................................2 - 9
2.1.6 FAN Connectors ............................................................................2 - 10
2.1.7 Rear I/O interface on Compact PCI Connectors rJ3, rJ4 and rJ5 .2 - 11
3. Installation ................................................................................3 - 3
3.1 Safety Requirements ...............................................................................3 - 3
3.2 Rear I/O Module Installation Procedures .................................................3 - 4
3.3 Rear I/O Module Removal Procedures ....................................................3 - 5
3.4 Installation of Peripheral Devices ............................................................3 - 5
3.4.1 USB Device Installation ...................................................................3 - 5
3.4.2 USB 2.0 NAND Flash Module Installation .......................................3 - 6
3.4.3 Installation of an External Serial ATA Device ..................................3 - 6
3.4.4 Installation of a 2.5” SATA HDD/SSD Device ..................................3 - 7
P R E L I M I N A R Y
Page iv ID 1043-56 20, Rev. 1.0
Page 5
CP-RIO6-001/-HD/-HD-216 Preface
List of Tables
1-1 CP-RIO6-001/-HD/-HD-216 Feature Comparison ..................................... 1 - 3
1-2 CP-RIO6-001/-HD/-HD-216 Main Specifications ..................................... 1 - 10
1-3 Standards for the CP-RIO6-001/-HD/-HD-216 ........................................ 1 - 12
1-4 Related Publications ................................................................................ 1 - 13
2-1 USB Connectors J6 and J7 Pinout ............................................................ 2 - 3
2-2 USB NAND Flash Connector J17 Pinout ................................................... 2 - 4
2-3 DVI Connector J9/J11 Pinout ..................................................................... 2 - 5
2-4 Pinout of Dual GbE Connector J8A/B ........................................................ 2 - 6
2-5 SATA Connector J17 Pinout ...................................................................... 2 - 7
2-6 SATA Connector J19 Pinout ...................................................................... 2 - 8
2-6 Serial Port Connector J15 (RS-232/RS-422) Pinout ................................. 2 - 9
2-7 Serial Port Connector J16 (RS-232) Pinout ............................................... 2 - 9
2-8 Fan Control Connectors J12 and J13 Pinout ........................................... 2 - 10
2-10 CP-RIO6-001/-HD Rear I/O CompactPCI Connector rJ3 Signals ........... 2 - 12
2-9 CP-RIO6-001/-HD Rear I/O CompactPCI Connector rJ3 Pinout ............. 2 - 12
2-12 CP-RIO6-001-HD-216 Rear I/O CompactPCI Connector rJ3 Signals ..... 2 - 13
2-11 CP-RIO6-001-HD-216 Rear I/O CompactPCI Connector rJ3 Pinout ....... 2 - 13
2-13 Rear I/O CompactPCI Connector rJ4 Pinout ........................................... 2 - 14
2-15 Rear I/O CompactPCI Rear I/O Connector rJ5 Signals ........................... 2 - 15
2-14 Rear I/O CompactPCI Connector rJ5 Pinout ........................................... 2 - 15
P R E L I M I N A R Y
ID 1043-5620, Rev. 1.0 Page v
Page 6
Preface CP-RIO6-001/-HD/-HD-216
This page has been intentionally left blank.
P R E L I M I N A R Y
Page vi ID 1043-5620, Rev. 1.0
Page 7
CP-RIO6-001/-HD/-HD-216 Preface
List of Figures
1-1 CP-RIO6-001Functional Block Diagram .................................................. 1 - 4
1-2 CP-RIO6-001-HD/CP-RIO6-001-HD-216 Functional Block Diagram ...... 1 - 5
1-3 CP-RIO6-001/-HD/-HD-216 Front Panels ................................................ 1 - 6
1-4 CP-RIO6-001 Board Layout – Front View ................................................ 1 - 7
1-5 CP-RIO6-001-HD Board Layout – Front View ......................................... 1 - 8
1-6 CP-RIO6-001-HD-216 Board Layout – Front View .................................. 1 - 9
2-1 USB Connectors J6 and J7 ...................................................................... 2 - 3
2-2 USB NAND Flash Con. J17 ..................................................................... 2 - 4
2-3 DVI Connector J9/J11 .............................................................................. 2 - 5
2-4 Dual Gigabit Ethernet Connector J8A/B ................................................. 2 - 6
2-5 SATA Connector J17 ................................................................................ 2 - 7
2-6 SATA Connector J19 ................................................................................ 2 - 8
2-7 Serial Port Connector J15/J16 ................................................................. 2 - 9
2-8 Fan Control Connectors J12 and J13 .................................................... 2 - 10
2-9 Rear I/O CompactPCI Connectors rJ3, rJ4 and rJ5 ............................. 2 - 11
3-1 Placement of the 2.5” SATA HDD/SSD on the CP-RIO6-001-HD/-HD-216 3 - 7
P R E L I M I N A R Y
ID 1043-5620, Rev. 1.0 Page vii
Page 8
Preface CP-RIO6-001/-HD/-HD-216
This page has been intentionally left blank.
P R E L I M I N A R Y
Page viii ID 1043-5620, Rev. 1.0
Page 9
CP-RIO6-001/-HD/-HD-216 Preface
Proprietary Note
This document contains information proprietary to Kontron. It may not be copied or transmitted
by any means, disclosed to others, or stored in any retrieval system or media without the prior
written consent of Kontron or one of its authorized agents.
The information contained in this document is, to the best of our knowledge, entirely correct.
However, Kontron cannot accept liability for any inaccuracies or the consequences thereof, or
for any liability arising from the use or application of any circuit, product, or example shown in
this document.
Kontron reserves the right to change, modify, or improve this document or the product
described herein, as seen fit by Kontron without further notice.
Trademarks
Kontron, the PEP logo and, if occurring in this manual, “CXM” are trademarks owned by Kontron, Kaufbeuren (Germany). In addition, this document may include names, company logos
and trademarks, which are registered trademarks and, therefore, proprietary to their respective
owners.
Environmental Protection Statement
This product has been manufactured to satisfy environmental protection requirements where
possible. Many of the components used (structural parts, printed circuit boards, connectors,
batteries, etc.) are capable of being recycled.
Final disposition of this product after its service life must be accomplished in accordance with
applicable country, state, or local laws or regulations.
P R E L I M I N A R Y
ID 1043-5620, Rev. 1.0 Page ix
Page 10
Preface CP-RIO6-001/-HD/-HD-216
Explanation of Symbols
Caution, Electric Shock!
This symbol and title warn of hazards due to electrical shocks (> 60V)
when touching products or parts of them. Failure to observe the precautions indicated and/or prescribed by the law may endanger your
life/health and/or result in damage to your material.
Please refer also to the section “High Voltage Safety Instructions” on
the following page.
Warning, ESD Sensitive Device!
This symbol and title inform that electronic boards and their components are sensitive to static electricity. Therefore, care must be taken
during all handling operations and inspections of this product, in
order to ensure product integrity at all times.
Please read also the section “Special Handling and Unpacking
Instructions” on the following page.
Warning!
This symbol and title emphasize points which, if not fully understood
and taken into consideration by the reader, may endanger your health
and/or result in damage to your material.
Note ...
This symbol and title emphasize aspects the reader should read
through carefully for his or her own advantage.
P R E L I M I N A R Y
Page x ID 1043-5620, Rev. 1.0
Page 11
CP-RIO6-001/-HD/-HD-216 Preface
For Your Safety
Y our new Kontron product was developed and tested carefully to provide all features necessary
to ensure its compliance with electrical safety requirements. It was also designed for a long
fault-free life. However, the life expectancy of your product can be drastically reduced by
improper treatment during unpacking and installation. Therefore, in the interest of your own
safety and of the correct operation of your new Kontron product, you are requested to conform
with the following guidelines.
High Voltage Safety Instructions
Warning!
All operations on this device must be carried out by sufficiently skilled
personnel only.
Caution, Electric Shock!
Before installing a not hot-swappable Kontron product into a system
always ensure that your mains power is switched off. This applies
also to the installation of piggybacks.
Serious electrical shock hazards can exist during all installation,
repair and maintenance operations with this product. Therefore,
always unplug the power cable and any other cables which provide
external voltages before performing work.
Special Handling and Unpacking Instructions
ESD Sensitive Device!
Electronic boards and their components are sensitive to static electricity. Therefore, care must be taken during all handling operations
and inspections of this product, in order to ensure product integrity at
all times.
Do not handle this product out of its protective enclosure while it is not used for operational
purposes unless it is otherwise protected.
P R E L I M I N A R Y
Whenever possible, unpack or pack this product only at EOS/ESD safe work stations. Where
a safe work station is not guaranteed, it is important for the user to be electrically discharged
before touching the product with his/her hands or tools. This is most easily done by touching a
metal part of your system housing.
It is particularly important to observe standard anti-static precautions when changing piggybacks, ROM devices, jumper settings etc. If the product contains batteries for RTC or memory
backup, ensure that the board is not placed on conductive surfaces, including anti-static plastics or sponges. They can cause short circuits and damage the batteries or con ductive circuit s
on the board.
ID 1043-5620, Rev. 1.0 Page xi
Page 12
Preface CP-RIO6-001/-HD/-HD-216
General Instructions on Usage
In order to maintain Kontron’s product warranty, this product must not be altered or modified in
any way. Changes or modifications to the device, which are not explicitly approved by Kontron
and described in this manual or received from Kontron’s Technical Support as a special
handling instruction, will void your warranty.
This device should only be installed in or connected to systems that fulfill all necessary
technical and specific environmental requirements. This applies also to the operational
temperature range of the specific board version, which must not be exceeded. If batteries are
present, their temperature restrictions must be taken into account.
In performing all necessary installation and application operations, please follow only the
instructions supplied by the present manual.
Keep all the original packaging material for future storage or warranty shipments. If it is
necessary to store or ship the board, please re-pack it as nearly as possible in the manner in
which it was delivered.
Special care is necessary when handling or unp acking the product. Please co nsult the special
handling and unpacking instruction on the previous page of this manual.
P R E L I M I N A R Y
Page xii ID 1043-5620, Rev. 1.0
Page 13
CP-RIO6-001/-HD/-HD-216 Preface
Two Year Warranty
Kontron grants the original purchaser of Kontron’s products a TWO YEAR LIMITED HARDWARE
WARRANTY
implied by anyone on behalf of Kontron are valid unless the consumer has the expre ss written
consent of Kontron.
Kontron warrants their own products, excluding software, to be free from manufacturing and
material defects for a period of 24 consecutive months from the date of purchase. This warranty
is not transferable nor extendible to cover any other users or long-term storage of the product.
It does not cover products which have been modified, altered or repaired by any other party
than Kontron or their authorized agents. Furthermore, any product which has been, or is suspected of being damaged as a result of negligence , improper use, incorrect handling, servicing
or maintenance, or which has been damaged as a result of excessive current/voltage or temperature, or which has had its serial number(s), any ot her markings or parts thereof altered, defaced or removed will also be excluded from this warranty.
If the customer’s eligibility for warranty has not been voided, in the event of any claim, he may
return the product at the earliest possible convenience to the original place of p urchase, together with a copy of the original document of purchase, a full description of the application the
product is used on and a description of the defect. Pack the product in such a way as to ensure
safe transportation (see our safety instructions).
as described in the following. However , no other warranties that may be granted or
Kontron provides for repair or replacement of any p art, assembly or su b-assembly at their own
discretion, or to refund the original cost of purchase, if appropriate. In the event of repair, refunding or replacement of any part, the ownership of the removed or replaced parts reverts to
Kontron, and the remaining part of the original guarantee, or any new guarantee to cover the
repaired or replaced items, will be transferred to cover the new or repaired items. Any extensions to the original guarantee are considered gestures of goodwill, and will be defined in the
“Repair Report” issued by Kontron with the repaired or replaced item.
Kontron will not accept liability for any further claims resulting directly or indirectly from any
warranty claim, other than the above specified repair, replacement or refunding. In particular,
all claims for damage to any system or process in which the product was employed, or any loss
incurred as a result of the product not functioning at any given time, are excluded. The extent
of Kontron liability to the customer shall not exceed the original purchase price of the item for
which the claim exists.
Kontron issues no warranty or representation, either explicit or implicit, with respect to its
products’ reliability, fitness, quality, marketability or ability to fulfil any particular application or
purpose. As a result, the products are sold “as is,” and the responsibility to ensure their
suitability for any given task remains tha t of the purchaser. In no event will Kontron be liable for
direct, indirect or consequential damages resulting from the use of our hardware or software
products, or documentation, even if Kon tron were advised of the possibility of such claims prior
to the purchase of the product or during any period since the date of its purchase.
Please remember that no Kontron employee, dealer or agent is authorized to make any
modification or addition to the above specified terms, either verbally o r in any other form, written
or electronically transmitted, without the company’s consent.
P R E L I M I N A R Y
ID 1043-5620, Rev. 1.0 Page xiii
Page 14
Preface CP-RIO6-001/-HD/-HD-216
This page has been intentionally left blank.
P R E L I M I N A R Y
Page xiv ID 1043-5620, Rev. 1.0
Page 15
CP-RIO6-001/-HD/-HD-216 Introduction
Chapter 1
1
Introduction
ID 1043-5620, Rev. 1.0 Page 1 - 1
P R E L I M I N A R Y
Page 16
Introduction CP-RIO6-001/-HD/-HD-216
This page has been intentionally left blank.
P R E L I M I N A R Y
Page 1 - 2 ID 1043-5620, Rev. 1.0
Page 17
CP-RIO6-001/-HD/-HD-216 Introduction
1. Introduction
1.1 Board Overview
The CP-RIO6-001, the CP-RIO6-001-HD, and the CP-RIO6-001-HD-216 are 6U CompactPCI
rear transition module designed for use with Kontron 6U CompactPCI CPU boards and provide
comprehensive rear I/O functionality for peripherals. In order to use these modules, a special
6U CompactPCI backplane with rear I/O support as well as a compatible and correctly
configured CPU board are required.
All three modules provide various data and communi cation interfaces as well as support for one
optional USB 2.0 NAND Flash module and one external SATA device. In addition, the CPRIO6-001-HD and the CP-RIO6-001-HD-216 provide support for one onboard 2.5" SAT A HDD/
SSD.
The CP-RIO6-001 comes with three USB 2.0 ports, two Gigabit Ethernet ports with LED signals, two digital video ports, one onboard SAT A port, two onboard COM ports and two onboard
fan connectors.
The CP-RIO6-001-HD comes with three USB 2.0 ports, two Gigabit Ethernet ports with LED
signals, one digital video port, two onboard SATA ports, two onboard COM ports and two onboard fan connectors.
The CP-RIO6-001-HD-216 comes with three USB 2.0 ports, one digital video port, two onboard
SATA ports, two onboard COM ports and two onboard fan connectors. On the front panel, the
CP-RIO6-001-HD-216 is populated with a dual Ethernet connector. However, this connector
has no functionality and has protective caps installed. The CP-RIO6-001-HD-216 is intended
for use in a PICMG 2.16 backplane.
All modules provide three CompactPCI connectors for connection to the backplane.
1.2 CP-RIO6-001/-HD/-HD-216 Feature Comparison
The following table provides a feature comparison of the CP-RIO6-001/-HD/-HD-216.
Table 1-1: CP-RIO6-001/-HD/-HD-216 Feature Comparison
PORT CP-RIO6-001 CP-RIO6-001-HD CP-RIO6-001-HD-216
Digital video port 2 1 1
Gigabit Ethernet 2 2 --
Ports
USB 2.0 2 2 2
Front Panel
COM 2 2 2
P R E L I M I N A R Y
USB 2.0 NAND Flash 1 1 1
SATA port for external
SATA device
SATA port for HDD/SSD -- 1 1
Onboard Ports
FAN 2 2 2
ID 1043-5620, Rev. 1.0 Page 1 - 3
111
Page 18
Introduction CP-RIO6-001/-HD/-HD-216
xxx
xxx
Onboard
Connector
Front Panel
Connector
CPCI
Connectors
rJ3
rJ4
rJ5
SATA
Connector
(7-pin)
H
D
M
I
/
D
V
I
S
A
T
A
xxx
Controller /
Driver
HDMI/DVI
DVI
Connector
DVI
Connector
RS-232
2x GbE
2x Mag
2
x
E
t
h
e
r
n
e
t
2
x
E
t
h
USB NAND
Flash
2x USB2.0
2x USB
U
S
B
COM2
(10-pin)
R
S
-
2
3
2
/
R
S
-
4
2
2
FAN1
FAN2
Sense
COM2
(10-pin)
1.3 Board Diagrams
The following diagrams provide additional information concerning the boards’ functionality and
component layout.
1.3.1 Functional Block Diagrams
Figure 1-1: CP-RIO6-001Functional Block Diagram
P R E L I M I N A R Y
Page 1 - 4 ID 1043-5620, Rev. 1.0
Page 19
CP-RIO6-001/-HD/-HD-216 Introduction
xxx
xxx
Onboard
Connector
Front Panel
Connector
CPCI
Connectors
rJ3
rJ4
rJ5
SATA
Connector
(7-pin)
S
A
T
A
xxx
Controller /
Driver
HDMI/DVI
DVI
Connector
RS-232
SATA
Socket
S
A
T
A
2x GbE
2x Mag
2
x
E
t
h
e
r
n
e
t
2
x
E
t
h
USB NAND
Flash
2x USB2.0
2x USB
U
S
B
COM2
(10-pin)
R
S
-
2
3
2
/
R
S
-
4
2
2
FAN1
FAN2
Sense
Not available on the
CP-RIO6-001-HD-216
COM2
(10-pin)
Figure 1-2: CP-RIO6-001-HD/CP-RIO6-001-HD-216 Functional Block Diagram
P R E L I M I N A R Y
ID 1043-5620, Rev. 1.0 Page 1 - 5
Page 20
Introduction CP-RIO6-001/-HD/-HD-216
CP-RIO6-001 CP-RIO6-001-HD CP-RIO6-001-HD-216
1.3.2 Front Panels
Figure 1-3: CP-RIO6-001/-HD/-HD-216 Front Panels
P R E L I M I N A R Y
Page 1 - 6 ID 1043-5620, Rev. 1.0
Page 21
CP-RIO6-001/-HD/-HD-216 Introduction
rJ3
rJ5
rJ4
USB
USB
Magn.
Magn.
J6
J7
GbE
B
GbE
A
J8
J16
(COM A)
J15
(COM B)
J17
(SATA)
HDMI/DVI
J11
HDMI/DVI
J9
J18
USB
NAND
Flash
1
2
10
9
1
2
10 9
12
10
9
1
1
J12
J13
17
1.3.3 Board Layout
Figure 1-4: CP-RIO6-001 Board Layout – Front View
P R E L I M I N A R Y
ID 1043-5620, Rev. 1.0 Page 1 - 7
Page 22
Introduction CP-RIO6-001/-HD/-HD-216
DVI/HDMI
J9
J18
USB
NAND
Flash
1
2
10
9
1
2
10 9
12
10
9
1
1
J12
J13
17
S1
J19
(SATA)
HDD
rJ3
rJ5
rJ4
USB
USB
Magn.
Magn.
J6
J7
GbE
B
GbE
A
J8
J16
(COM A)
J15
(COM B)
J17
(SATA)
Figure 1-5: CP-RIO6-001-HD Board Layout – Front View
P R E L I M I N A R Y
Page 1 - 8 ID 1043-5620, Rev. 1.0
Page 23
CP-RIO6-001/-HD/-HD-216 Introduction
DVI/HDMI
J9
J18
USB
NAND
Flash
1
2
10
9
1
2
10 9
12
10
9
1
1
J12
J13
17
S1
J19
(SATA)
HDD
rJ3
rJ5
rJ4
USB
USB
Magn.
Magn.
J6
J7
J8
J16
(COM A)
J15
(COM B)
J17
(SATA)
Protective
Caps
Figure 1-6: CP-RIO6-001-HD-216 Board Layout – Front View
P R E L I M I N A R Y
ID 1043-5620, Rev. 1.0 Page 1 - 9
Page 24
Introduction CP-RIO6-001/-HD/-HD-216
1.4 Technical Specification
Table 1-2: CP-RIO6-001/-HD/-HD-216 Main Specifications
CP-RIO6-001/-HD/-HD-216 SPECIFICATIONS
Digital Video CP-RIO6-001:
• Two digital video interfaces implemented as two 29-pin DVI-I con-
nectors, J9 and J11, supporting HDMI and DVI signaling for digital
monitors
CP-RIO6-001-HD, CP-RIO6-001-HD-216:
• One digital video interface implemented as a DVI-I connector , J9, for
connecting a monitor with a DVI/HDMI interface
Ethernet CP-RIO6-001, CP-RIO6-001-HD:
• Two Gigabit Ethernet interfaces implemented as a dua l RJ -45 co n-
nector, J19A/B
Front Panel Interfaces
CP-RIO6-001-HD-216:
• Ethernet not supported du e to the fact that the Et hernet interface is
isolated on the CompactPCI connector rJ3
USB Two USB 2.0 interfaces on type A connectors, J6 and J7
SATA CP-RIO6-001:
• One SATA interface implemented as one onboa rd connect or, J17,
for connecting a SATA device via a SATA cable
CP-RIO6-001-HD, CP-RIO6-001-HD-216:
Up to two SATA interfaces implemented as two onboard connectors:
• One SATA connector, J17, for connecting a SATA device via a
SATA cable
• One SATA connector, J19, for installing a 2.5” SATA HDD/SSD
(optional)
USB One onboard connector, J18, for connecting one USB 2.0 NAND Flash
module
Onboard Interfaces
COM Two onboard COM ports implemented as two 10-pin, 2.54 mm onboard
P R E L I M I N A R Y
Fan Two fan connectors, J12 and J13, with PWM control and sense inputs for
CompactPCI Three CompactPCI connectors, rJ3, rJ4 and rJ5, for connecting the mod-
connectors, J15 and J16
monitoring the fan speed.
ule to the backplane
Page 1 - 10 ID 1043-5620, Rev. 1.0
Page 25
CP-RIO6-001/-HD/-HD-216 Introduction
Note ...
When additional components are installed, refer
to their operational specifications as this will influence the modules’ operational and storage temperature.
Table 1-2: CP-RIO6-001/-HD/-HD-216 Main Specifications (Continued)
CP-RIO6-001/-HD/-HD-216 SPECIFICATIONS
Temperature Range Operational: 0°C to +60°C Standard
-40°C to +85°C E2 (optional)
Storage: -55°C to +85°C Without any additional components
General
Mechanical 6U, 4HP, CompactPCI-compliant form factor
Dimensions 233.35 mm x 80 mm
Board Weight CP-RIO6-001: 224 g (without USB NAND Flash module)
CP-RIO6-001-HD: 218 g (without USB NAND Flash module)
CP-RIO6-001-HD-216: 224 g (without USB NAND Flash module)
ID 1043-5620, Rev. 1.0 Page 1 - 11
P R E L I M I N A R Y
Page 26
Introduction CP-RIO6-001/-HD/-HD-216
1.5 Standards
The CP-RIO6-001/-HD/-HD-216 complies with the requirements of the following standards:
Table 1-3: Standards for the CP-RIO6-001/-HD/-HD-216
TYPE ASPECT STANDARD REMARKS
CE Emission EN55022
EN61000-6-3
Immission EN55024
EN61000-6-2
Electrical Safety EN60950-1 --
Mechanical Mechanical Dimen-
sions
Environmental Climatic Humidity IEC60068-2-78 93% RH at 40°C, non-condensing
WEEE Directive 2002/96/EC Waste electrical and electronic equipment
RoHS Directive 2002/95/EC Restriction of the use of certain hazardous
Vibration
(Sinusoidal)
Single Shock IEC61131-2
IEEE 1101.10 --
IEC61131-2
IEC60068-2-6
IEC60068-2-27
--
--
substances in electrical and electronic
equipment
Test parameters (without protective caps):
• 5-150 (Hz) frequency range
• 1 (g) acceleration
• 1 (oct/min) sweep rate
• 10 cycles/axis
• 3 axes
Test parameters:
• 15 (g) acceleration
• 11 (ms) pulse duration
• 3 shocks per direction
• 6 directions
• 5 (s) recovery time
P R E L I M I N A R Y
Note ...
Kontron performs comprehensive environmental testing of its products in accordance with applicable standards.
Customers desiring to perform further environmental testing of Kontron products must contact Kontron for assistance prior to performing any such testing.
This is necessary, as it is possible that environmental testing can be destructive
when not performed in accordance with the applicable specifications.
In particular, for example, boards without conformal coating must not be
exposed to a change of temperature exceeding 1K/minute, averaged over a
period of not more than five minutes. Otherwise, condensation may cause irreversible damage, especially when the board is powered up again.
Kontron does not accept any responsibility for damage to products resulting
from destructive environmental testing.
Page 1 - 12 ID 1043-5620, Rev. 1.0
Page 27
CP-RIO6-001/-HD/-HD-216 Introduction
1.6 Related Publications
The following publications contain information relating to the CP-RIO6-001/-HD/-HD-216.
Table 1-4: Related Publications
PRODUCT PUBLICATION
CompactPCI Systems and
Boards
All Kontron products Product Safety and Implementation Guide, ID 1021-9142
CompactPCI Specification 2.0, Rev. 3.0
CompactPCI Packet Switching Backplane Specification PICMG 2.16 Rev. 1.0
(CP-RIO6-001-HD-216)
Kontron CompactPCI Backplane Manual, ID 24229
ID 1043-5620, Rev. 1.0 Page 1 - 13
P R E L I M I N A R Y
Page 28
Introduction CP-RIO6-001/-HD/-HD-216
This page has been intentionally left blank.
P R E L I M I N A R Y
Page 1 - 14 ID 1043-5620, Rev. 1.0
Loading...