Kontron COMe Ref. Carrier-i T6 TMIP, COMe Ref. Carrier-i T6 TMIV, COMe Ref. Carrier-i T6 TMIE User Manual
Page 1
P R E L I M I N A R Y
The pulse of innovation
» User Guide «
COMe Ref. Carrier-i T6 TMI
Doc. ID: 1059-4224, Rev. 1.3
Date: April 15, 2019
Page 2
P R E L I M I N A R Y
2
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
Revision History
Imprint
Kontron Europe GmbH may be contacted via the following:
MAILING ADDRESS TELEPHONE AND E-MAIL
Kontron Europe GmbH +49 (0) 800-SALESKONTRON
Lise-Meitner-Str. 3-5 sales@kontron.com
86156 Augsburg, Germany
For further information concerning other Kontron products, please visit our Internet website:
www.kontron.com.
Disclaimer
Copyright © 2016 Kontron AG. All rights reserved. All data is for information purposes only and not
guaranteed for legal purposes. Information has been carefully checked and is believed to be accurate;
however, no responsibility is assumed for inaccuracies. Kontron and the Kontron logo and all other
trademarks or registered trademarks are the property of their respective owners and are recognized.
Specifications are subject to change without notice.
Revision Brief Description of Changes Date of Issue
1.0 Initial issue 24-Jun-2016
1.1 Update of table numbers
Included 1.4 Accessories
05-Aug-2016
1.2 2.1.1 SPI Flash update
2.3.14 DIP Switch update of table 16, poition 6
23-Aug-2017
1.3 2.3.15 Added Power connector (J1) mating connector information 15-Apr-2019
Page 3
P R E L I M I N A R Y
3
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
Contents
Revision History ..........................................................................................................2
Imprint .....................................................................................................................2
Disclaimer ..................................................................................................................2
Contents ....................................................................................................................3
Tables .......................................................................................................................5
Figures ......................................................................................................................6
Warranty ....................................................................................................................7
Proprietary Note ..........................................................................................................7
Trademarks ................................................................................................................7
Environmental Protection Statement ................................................................................7
1 Introduction ....................................................................................... 8
1.1 Carrier Overview .......................................................................................... 8
1.2 Board Diagrams........................................................................................... 9
1.2.1 Functional Block Diagram .............................................................................. 9
1.2.2 Rear Panel ................................................................................................ 10
1.2.3 Board Layout ............................................................................................. 10
1.2.3.1 Component Overview ................................................................................... 12
1.3 Technical Specification ................................................................................ 14
1.4 Accessories ............................................................................................... 16
1.5 Standards ................................................................................................. 17
1.6 Related Publications.................................................................................... 18
2 Functional Description ......................................................................... 19
2.1 Memory .................................................................................................... 19
2.1.1 SPI Flash .................................................................................................. 19
2.1.2 Carrier EEPROM .......................................................................................... 19
2.2 Graphics Interfaces ..................................................................................... 19
2.2.1 Digital Display Interfaces ............................................................................. 19
2.2.2 LVDS/eDP Interface ..................................................................................... 20
2.2.3 PEG Lanes ................................................................................................. 20
2.3 System Interfaces ....................................................................................... 21
2.3.1 PCI Express Interfaces.................................................................................. 21
2.3.2 SATA Interfaces .......................................................................................... 21
2.3.3 M.2 Interface ............................................................................................. 21
2.3.4 Gigabit Ethernet Interfaces ........................................................................... 21
2.3.5 USB 2.0 Interfaces ...................................................................................... 22
2.3.6 USB 3.0 Interfaces ...................................................................................... 23
2.3.7 HD Audio Interfaces .................................................................................... 24
2.3.8 UART Interfaces.......................................................................................... 25
Page 4
P R E L I M I N A R Y
4
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
2.3.9 GPIO Interfaces .......................................................................................... 25
2.3.10 SIM Interface............................................................................................. 26
2.3.11 SYS_Signals / Embedded Interfaces ................................................................ 26
2.3.12 CPU Fan Interface ....................................................................................... 27
2.3.13 Front Panel Interface................................................................................... 27
2.3.14 DIP Switch ................................................................................................ 28
2.3.15 Power Supply and Management ...................................................................... 29
2.3.16 RTC.......................................................................................................... 29
Page 5
P R E L I M I N A R Y
5
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
Tables
1 COMe Ref. Carrier-i T6 TMI Variants ...........................................................................8
2 Component Overview .......................................................................................... 12
3 COMe Ref. Carrier-i T6 TMI Main Specifications .......................................................... 14
4 COMe Ref. Carrier-i T6 TMI Accessories .................................................................... 16
5 Standards ........................................................................................................ 17
6 Related Publications ........................................................................................... 18
7 LVDS/JILI Connector J8 Pinout ............................................................................. 20
8 Pinout of USB 3.0/2.0 Pin Header J7 ...................................................................... 23
9 Front Panel HD Audio Header J22 Pinout ................................................................. 24
10 S/PDIF Header J23 Pinout .................................................................................... 24
11 Pinout of Pin Headers J30 and J29 ......................................................................... 25
12 GPIO Pin Header J32 ........................................................................................... 25
13 Pin Header J31 .................................................................................................. 26
14 PWM Fan Connector J4 ........................................................................................ 27
15 Front Panel Connector J27 Pinout .......................................................................... 27
16 DIP Switch SW1 Functionality ................................................................................ 28
17 Power Connector J1 Pinout ................................................................................... 29
Page 6
P R E L I M I N A R Y
6
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
Figures
1 COMe Ref. Carrier-i T6 TMI Functional Block Diagram .................................................. 9
2 COMe Ref. Carrier-i T6 TMI Rear Panel .................................................................... 10
3 COMe Ref. Carrier-i T6 TMI Layout - Top View ............................................................ 10
4 COMe Ref. Carrier-i T6 TMI Layout - Bottom View ....................................................... 11
5 LVDS/JILI Connector J8 ...................................................................................... 20
6 USB 3.0/2.0 Pin Header J7 .................................................................................. 23
7 Front Panel HD Audio Header J22 ......................................................................... 24
8 S/PDIF Header J23 ............................................................................................ 24
9 Pin Headers J30 and J29 ..................................................................................... 25
10 GPIO Pin Header J32 .......................................................................................... 25
11 Pin Header J31 ................................................................................................. 26
12 PWM Fan Connector J4 ....................................................................................... 27
13 Front Panel Connector J27 .................................................................................. 27
14 DIP Switch SW1 ................................................................................................ 28
15 Power Connector J1 ........................................................................................... 29
Page 7
P R E L I M I N A R Y
7
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
Warranty
This Kontron product is warranted against defects in material and workmanship for the warranty period
from the date of shipment. During the warranty period, Kontron will at its discretion decide to repair
or replace defective products.
Within the warranty period, the repair of products is free of charge as long as warranty conditions are
observed.
The warranty does not apply to defects resulting from improper or inadequate maintenance or handling
by the buyer, unauthorized modification or misuse, operation outside of the product’s environmental
specifications or improper installation or maintenance.
Kontron will not be responsible for any defects or damages to other products not supplied by Kontron
that are caused by a faulty Kontron product.
Proprietary Note
This document contains information proprietary to Kontron. It may not be copied or transmitted by any
means, disclosed to others, or stored in any retrieval system or media without the prior written consent
of Kontron or one of its authorized agents.
The information contained in this document is, to the best of our knowledge, entirely correct. However, Kontron cannot accept liability for any inaccuracies or the consequences thereof, or for any liability
arising from the use or application of any circuit, product, or example shown in this document.
Kontron reserves the right to change, modify, or improve this document or the product described herein, as seen fit by Kontron without further notice.
Trademarks
This document may include names, company logos and trademarks, which are registered trademarks
and, therefore, proprietary to their respective owners.
Environmental Protection Statement
This product has been manufactured to satisfy environmental protection requirements where possible.
Many of the components used (structural parts, printed circuit boards, connectors, batteries, etc.) are
capable of being recycled.
Final disposition of this product after its service life must be accomplished in accordance with applicable country, state, or local laws or regulations.
Page 8
P R E L I M I N A R Y
8
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
1 Introduction
1.1 Carrier Overview
The COMe Reference Carrier-i Type 6 Thin-MiniITX (hereinafter referred to as COMe Ref. Carrier-i T6 TMI)
is a COM Express® pinout Type 6, Thin-mITX form factor-compliant reference carrier designed to accommodate a basic/compact Type 6 COM Express® Computer-on-Module compliant with the PICMG
COM.0 specification Rev 2.1.
The COMe Ref. Carrier-i T6 TMI comes in three variants:
» COMe Reference Carrier-i Type 6 Thin-MiniITX Professional (COMe Ref. Carrier-i T6 TMIP),
» COMe Reference Carrier-i Type 6 Thin-MiniITX Value (COMe Ref. Carrier-i T6 TMIV), and
» COMe Reference Carrier-i Type 6 Thin-MiniITX Entry (COMe Ref. Carrier-i T6 TMIE).
The following table provides information about the features implemented on the COMe Ref. Carrier-i T6
TMI variants.
Table 1: COMe Ref. Carrier-i T6 TMI Variants
COMe Ref. Carrier-i T6 TMIP
(P/N 38115-0000-00-0)
COMe Ref. Carrier-i T6 TMIV
(P/N 38115-0000-00-1)
COMe Ref. Carrier-i T6 TMIE
(P/N 38115-0000-00-2)
SPI BIOS Socket xxx
Carrier EEPROM xxx
DDI1 - DP++ xxx
DDI2 - mDP++ xx--
DDI3 - mDP++ xx--
LVDS xxx
mDP++ (eDP) -- -- --
mPCIe0 xxx
mPCIe1 / mSATA xx--
GBLan0 (Module) xxx
GBLan1 (Carrier) xx--
SATA0 (top) xxx
SATA3 (bottom) x----
M.2 x----
USB 2.0 / 3.0 I/O xxx
USB 3.0 Pin Header xx--
HDA Codec xx--
Line-In/Out xx--
FP Audio xx--
S/PDIF xx--
SER0/1 xxx
GPIO xxx
SIM xx--
Sys Signals xxx
Sys Panel xxx
CPU Fan xxx
Page 9
P R E L I M I N A R Y
9
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
1.2 Board Diagrams
The following diagrams provide additional information concerning board functionality and component
layout.
1.2.1 Functional Block Diagram
Figure 1: COMe Ref. Carrier-i T6 TMI Functional Block Diagram
RTC connector xxx
Goldcap 1.5F -- x --
Goldcap 2.5F x----
12V Input xxx
8.5 - 30V Input x----
Rubber Feet x----
Table 1: COMe Ref. Carrier-i T6 TMI Variants (Continued)
COMe Ref. Carrier-i T6 TMIP
(P/N 38115-0000-00-0)
COMe Ref. Carrier-i T6 TMIV
(P/N 38115-0000-00-1)
COMe Ref. Carrier-i T6 TMIE
(P/N 38115-0000-00-2)
GBE#0
RTC
DDI3
5V_SB
PCIe #2
GPIO
I2C/SMB/WDT/LID/Sleep
PWRBTN# / SYS_RESET / HDD_ACT / SYS_LED
EXT_FAN
Rapid Shutdown
PCIe #0
USB 2.0 #6
USB 2.0 #2/3
USB 2.0 #0/1
USB 2.0 #7
PCIe #1
SATA #1
SATA #0
SATA #3
SER0/1
LVDS/eDP
DDI1
DDI2
USB 3.0 #0/1
USB 3.0 #2/3
Line In
FP_Audio
HDA
HD Audio
Line Out
USB 2.0 #4/5
SPKR
Front Panel
DS
Internal connector
or pin header
IO Shield
Jumper /
DataSwitch
Component
S/PDIF In/Out
USB 2.0
USB 3.0
USB 3.0
mini PCIe
mini PCIe
mSATA
SATA
RDRV
DP
Ethernet
JILI/LVDS
GPIO Header
SYS Signals
Front Panel
CPU_FAN
12V
8.5 - 30V
DS
COM1/COM2
I/O Power to Peripherals
SATA
RDRV
Ethernet
GBE
GBE#1
PEG #1-3
SIM Card
mDP
mDP
mDP
Switch
Battery Connector
Goldcap
RDRV
RDRV
RDRV
RDRV
Power
DS
USB-PWR
DS
EEPROM
SPI Flash
optional
PEG #0
C
O
N
N
E
C
T
O
R
C
D
RDRV
Switch
SATA #2
M.2
SPI
C
O
N
N
E
C
T
O
R
A
B
DS
Page 10
P R E L I M I N A R Y
10
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
1.2.2 Rear Panel
Figure 2: COMe Ref. Carrier-i T6 TMI Rear Panel
1.2.3 Board Layout
Figure 3: COMe Ref. Carrier-i T6 TMI Layout - Top View
DisplayPort
Voltage
Input
miniDP
miniDP
LAN LAN
Line-OutLine-In
USB
2.0
USB
3.0/2.0
1
J6
J10
C35
J1
J5
J7
J11
J12
U5
U7
U9
U41
J13
J14
J15
U11
U6
U8
Compact Module
Basic Module
U10
U42
J16 J17
J18
J19
J20
J25
J22
U13
J23
J36
SW1
J28J24
J21
J29
J30
J31
J27
12
12 11
U30
J26
J8
J4
J9
U3
U2
J32
D35
D37
D36
D38
D39
Page 11
P R E L I M I N A R Y
11
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
Figure 4: COMe Ref. Carrier-i T6 TMI Layout - Bottom View
J33
J34
U29
J35
Page 12
P R E L I M I N A R Y
12
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
1.2.3.1 Component Overview
Table 2: Component Overview
COMPONENT DESCRIPTION
C35 Goldcap
D35 Status LED: SUS_S3
D36 Status LED: SUS_S4
D37 Status LED: SUS_S5
D38 Status LED: V12_S5
D39 Status LED: V5.0_V3.3_PGOOD
J1 Power connector (8.5V – 30V input voltage)
J4 PWM fan connector
J5 SATA plug connector (with power connector)
J6 DC jack (12V only)
J7 USB 3.0/2.0 pin header
J8 LVDS / JILI connector
J9 Mini DisplayPort++ connector (eDP option)
J10 USB 2.0 double-stack connector
J11 USB 3.0/2.0 double-stack connector
J12 DisplayPort++ connector (DDI1)
J13 Mini PCIe card latch (full-size) / mSATA socket
J14 COMe connector (Row A and B)
J15 COMe connector (Row C and D)
J16 Mini DisplayPort++ connector (DDI3)
J17 Mini DisplayPort++ connector (DDI2)
J18 RJ45 Ethernet connector
J19 SPI BIOS socket
J20 RJ45 Ethernet connector
J21 Mini PCIe card slot (full-size) / mSATA socket
J22 Front panel HD audio header
J23 S/PDIF Header
J24 Mini PCIe card slot (half-size)
J25 Rear panel line-in connector
J26 Rear panel SPK / line-out connector
J27 Front panel connector
J28 Mini PCIe card latch (half-size)
J29 COM port pin header (COM2/SER1)
J30 COM port pin header (COM1/SER0)
J31 SYS_Signals / embedded interfaces pin header
J32 GPIO pin header
J33 SATA receptacle connector (with power connector)
J34 M.2 socket
J35 SIM card slot
J36 CMOS battery connector
Page 13
P R E L I M I N A R Y
13
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
SW1 DIP switch
U2 Redriver IC for SATA interfacing (SATA#0)
U3 Redriver IC for SATA interfacing (SATA#0)
U5 Redriver IC for DP interfacing (DDI1)
U6 Redriver IC for SATA interfacing (SATA#3)
U7 Redriver IC for DP interfacing (DDI3)
U8 Redriver IC for SATA interfacing (SATA#3)
U9 Redriver IC for DP interfacing (DDI2)
U10 Redriver IC for SATA interfacing (SATA#1)
U11 Redriver IC for SATA interfacing (SATA#1)
U13 HD Audio Codec IDT / Tempo Semi 92HD73C
U29 Intel® Ethernet Controller I210-IT
U30 Carrier EEPROM (FRUPROM)
U41 Redriver IC for SATA interfacing (SATA#2)
U42 Redriver IC for SATA interfacing (SATA#2)
Table 2: Component Overview (Continued)
COMPONENT DESCRIPTION
Page 14
P R E L I M I N A R Y
14
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
1.3 Technical Specification
Table 3: COMe Ref. Carrier-i T6 TMI Main Specifications
FEATURES SPECIFICATIONS
CPU
Processor & Chipset Via COMe basic/compact Type 6 module
Memory
System Memory Via COMe basic/compact Type 6 module
Flash Memory One SPI BIOS socket for SPI flash ICs with up to 16 MB flash memory
EEPROM EEPROM with 32 kbit on the carrier (FRUPROM)
Graphics Interfaces
Digital Display Interfaces Three digital display interfaces (DDI):
» DDI1: DisplayPort++ connector from COMe DDI1 with redriver IC, J12
» DDI2: Mini DisplayPort++ connector from COMe DDI2 with redriver IC, J17
» DDI3: Mini DisplayPort++ connector from COMe DDI3 with redriver IC, J16
LVDS LVDS / JILI connector (24-bit, dual-channel LVDS), J8
Embedded DisplayPort Mini DisplayPort++ connector via eDP (optional, instead of LVDS), J9
PEG Four PEG lanes (PEG#[0-3]) used for the M.2 interface
System Interfaces
PCI Express Three PCIe interfaces:
» PCIe#0 for Mini PCIe 2.0 half-size card slot connected to the SIM card slot,
J24
» PCIe#1 for Mini PCIe 2.0 full-size card slot muxed with SATA#1 (mSATA) and
connected to the SIM card slot, J21
» PCIe#2 for the onboard Gigabit Ethernet controller
SATA Four SATA 6 Gb/s interfaces:
» SATA#0 via the 22-pin SATA plug connector (with redriver ICs), J5
» SATA#1 for the mSATA socket / Mini PCIe full-size card slot (with redriver ICs), J21
» SATA#2 muxed with PEG#0 for the M.2 interface (with redriver ICs)
» SATA#3 via the 22-pin SATA receptacle connector (with redriver ICs), J33
M.2 M.2 socket via PEG#[0-3] and SATA#2 (muxed with PEG#0), J34
Ethernet Two Gigabit Ethernet interfaces:
» GbE#0 on RJ45 connector, J18, via COMe basic/compact Type 6 module
» GbE#1 on RJ45 connector, J20, via the onboard GbE controller (Intel® Ether-
net Controller I210-IT)
USB 2.0 Eight USB 2.0 interfaces:
» Two USB 2.0 interfaces (USB#[0;1]) for USB 3.0/2.0 double-stack connector,
J11
» Two USB 2.0 interfaces (USB#[2;3]) for USB 3.0/2.0 pin header, J7
» Two USB 2.0 interfaces (USB#[4;5]) for USB 2.0 double-stack connector, J10
» One USB 2.0 interface (USB#6) for PCIe#0 (Mini PCIe half-size interface)
» One USB 2.0 interface (USB#7) for PCIe#1 (Mini PCIe full-size/mSATA inter-
face)
USB 3.0 Four USB 3.0 interfaces:
» Two USB 3.0 interfaces (USB_SS#[0;1]) for USB 3.0/2.0 double-stack con-
nector, J11
» Two USB 3.0 interfaces (USB_SS#[2;3]) for USB 3.0/2.0 pin header, J7
Page 15
P R E L I M I N A R Y
15
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
System Interfaces
HD Audio Four HD Audio interfaces:
» Rear panel line-in connector, J25
» Rear panel SPK/line-out connector, J26
» Front panel HD audio header, J22
» S/PDIF header, J23
UART Two RS-232 COM ports (RX/TX only) via pin headers, J30 (COM1/SER0) and J29
(COM2/SER1)
System Interfaces
GPIO Four GPIs and four GPOs via the 10-pin GPIO pin header, J32
SIM SIM card slot connected to both Mini PCIe interfaces, J35
I2CI
2
C interface via 15-pin SYS_Signals / embedded interfaces pin header, J31
SMBus SMBus interface via 15-pin SYS_Signals / embedded interfaces pin header, J31
LID/SLEEP LID/SLEEP signals via 15-pin SYS_Signals / embedded interfaces pin header, J31
CPU Fan One 4-pin PWM fan connector, J4
LEDs Two status LEDs available via the front panel connector, J27:
»Power LED
» HDD Activity LED
Switch
DIP Switch One 8-position DIP switch, SW1, for board configuration
Power Supply and
Management
Power Supply Power input 1: 12V only
Power input 2: 8.5V - 30V wide input range
Power / Reset Button Available via the front panel connector, J27
RTC 2-pin connector for external CMOS battery, J36
Goldcap for RTC backup, C35
General
BIOS Via COMe basic/compact Type 6 module
Temperature Range Operational: -40°C to +85°C
Storage: -40°C to +85°C
Note: When additional components are installed, refer to their operational
specifications as this will influence the operational and storage
temperature of the COMe Ref. Carrier-i T6 TMI.
Climatic Humidity 93% RH at 40 °C, non-condensing (acc. to IEC 60068-2-78)
Form Factor COM Express® carrier, pinout Type 6, Thin-mITX form factor
Dimensions 170 mm x 170 mm (mITX)
Max. component height:
Top side: 16.2 mm
Bottom side: 5.4 mm
Table 3: COMe Ref. Carrier-i T6 TMI Main Specifications (Continued)
FEATURES SPECIFICATIONS
Page 16
P R E L I M I N A R Y
16
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
1.4 Accessories
The following accessories are available for the COMe Ref. Carrier-i T6 TMI.
Table 4: COMe Ref. Carrier-i T6 TMI Accessories
Part Number Part Name Description
96006-0000-00-2 COMe Post T6 NFCB POST Code / Debug card
38019-0000-00-0 ADA-COMe-Height-Dual EERC height adapter
38017-0000-00-5 COMe Mount Kit 5 mm 1 set Mounting Kit for 1 module including screws for
5 mm connectors
38017-0100-00-5 COMe Mount Kit 5 mm 100 sets Mounting Kit for 100 modules including screws for
5 mm connectors
38017-0000-00-0 COMe Mount Kit 8 mm 1 set Mounting Kit for 1 module including screws for
8 mm connectors
38017-0100-00-0 COMe Mount Kit 8 mm 100 sets Mounting Kit for 100 modules including screws for
8 mm connectors
9-5000-0352 ADA-LVDS_DVI 18 bit 18 bit LVDS to DVI converter
9-5000-0353 ADA-LVDS_DVI 24 bit 24 bit LVDS to DVI converter
96006-0000-00-8 ADA-DP-LVDS DP to LVDS adapter
96082-0000-00-0 KAB-ADAPT-DP-DVI DP to DVI adapter cable
96083-0000-00-0 KAB-ADAPT-DP-VGA DP to VGA adapter cable
96084-0000-00-0 KAB-ADAPT-DP-HDMI DP to HDMI adapter cable
Page 17
P R E L I M I N A R Y
17
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
1.5 Standards
This product complies with the requirements of the following standards.
Note: Customers desiring to perform further environmental testing of the COMe Ref. Carrier-i T6
TMI must contact Kontron for assistance prior to performing any such testing.
Boards without conformal coating must not be exposed to a change of temperature which
can lead to condensation, as it may cause irreversible damage especially when the board
is powered up again.
Kontron does not accept any responsibility for damage to products resulting from destructive environmental testing.
Table 5: Standards
TYPE ASPECT STANDARD REMARKS
CE Emission EN61000-6-3, EN55022 --
Electrical Safety Directive 2014/35/EU Low Voltage Directive (LVD)
EN60950-1 --
Product Safety Directive 2001/95/EC General Product Safety Directive
EMC Directive 2014/30/EU Electromagnetic Compatibility
Environmental Climatic Humidity IEC60068-2-78 (see note below) --
WEEE Directive 2002/96/EC Waste electrical and electronic
equipment
RoHS 2 Directive 2011/65/EU Restriction of the use of certain
hazardous substances in electri-
cal and electronic equipment
Environmental Vibration
(Sinusoidal)
IEC60068-2-6 Test parameters:
9-150 (Hz) frequency range
1 (g) acceleration
1 (oct/min) sweep rate
10 cycles/axis
3 axes
Single Shock IEC60068-2-27 Test parameters:
15 (g) acceleration
11 (ms) shock duration half sine
3 number of shocks per direction
(total: 18)
6 directions
5 (s) recovery time
Page 18
P R E L I M I N A R Y
18
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
1.6 Related Publications
The following publications contain information relating to this product.
Table 6: Related Publications
PRODUCT PUBLICATION
COM Express® COM Express® Carrier Design Guide Rev 2.0
COM Express® Module Base Specification Rev 2.1
SATA Serial ATA Specification Revision 3.0
PCI Express PCI Express Base Specification Rev 2.0
PCI Express M.2 Specification Rev 1.0
DisplayPort Display Port 1.1a Standard
Display Port 1.2 Standard
USB Universal Serial Bus (USB) 2.0 Specification Rev 2.0
Universal Serial Bus (USB) 3.0 Specification Rev 1.0
I
2
C
I2C Bus Specification Version 4.0
SMBus SMBus Specification Version 2.0
ACPI ACPI spec Rev 5.0
Page 19
P R E L I M I N A R Y
19
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
2 Functional Description
2.1 Memory
2.1.1 SPI Flash
The COMe Ref. Carrier-i T6 TMI provides one SPI BIOS socket, J19, for SPI flash ICs with up to 16 MB
flash memory for use with an external Carrier BIOS. Recommended SPI flash ICs include Winbond
W25Q64FVSSIG (8 MB) and W25Q128FVSIG (16 MB), depending on the COMe module used. Booting
from the Carrier SPI flash can be enabled or disabled via the onboard DIP switch SW1.
2.1.2 Carrier EEPROM
The COMe Ref. Carrier-i T6 TMI comes with an onboard 32-kbit I²C EEPROM, U30, for storage of manufacturer records or COMe module information.
2.2 Graphics Interfaces
2.2.1 Digital Display Interfaces
The COMe Ref. Carrier-i T6 TMI provides the following digital display interfaces (DDIs):
» DDI1 from the COMe module is directly mapped to the DisplayPort++ connector, J12, through
a redriver IC, U5
» DDI2 from the COMe module is directly mapped to the Mini DisplayPort++ connector, J17,
through a redriver IC, U9
» DDI3 from the COMe module is directly mapped to the Mini DisplayPort++ connector, J16,
through a redriver IC, U7
Note: The Mini DisplayPort++ connectors J16 and J17 are available as a standard feature on the
COMe Ref. Carrier-i T6 TMIV (Value) and the COMe Ref. Carrier-i T6 TMIP (Professional) versions.
Page 20
P R E L I M I N A R Y
20
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
2.2.2 LVDS/eDP Interface
The COMe Ref. Carrier-i T6 TMI supports a 24-bit, dual-channel LVDS interface via the LVDS/JILI connector, J8.
The following figure and table provide pinout information for the LVDS/JILI connector, J8.
If eDP support is required, the COMe Ref. Carrier-i T6 TMI may optionally be equipped with a Mini DisplayPort++ connector, J9, instead of the LVDS/JILI connector, J8.
Note: In order to use the eDP interface, the COMe module installed must also support eDP.
2.2.3 PEG Lanes
The COMe Ref. Carrier-i T6 TMI provides four PEG lanes (PEG#[0-3]) used for the M.2 socket, J34. PEG#0
is muxed with SATA#2.
Figure 5: LVDS/JILI Connector J8
J8
140
Table 7: LVDS/JILI Connector J8 Pinout
PIN SIGNAL PIN SIGNAL
1 LVDS_BKLT_CTRL 21 LVDS_B1+
2LVDS_A0- 22GND
3 LVDS_A0+ 23 LVDS_B2-
4 LVDS_VDD_EN 24 LVDS_B2+
5LVDS_A1- 25GND
6 LVDS_A1+ 26 LVDS_B_CK-
7NC 27LVDS_B_CK+
8LVDS_A2- 28GND
9 LVDS_A2+ 29 LVDS_B3-
10 GND 30 LVDS_B3+
11 LVDS_A_CK- 31 +5V
12 LVDS_A_CK+ 32 +5V
13 GND 33 +5V
14 LVDS_A3- 34 +5V
15 LVDS_A3+ 35 LVDS_BKLT_EN
16 LVDS_I2C_DAT 36 GND
17 LVDS_B0- 37 GND
18 LVDS_B0+ 38 +12V
19 LVDS_IC2_CK 39 +12V
20 LVDS_B1- 40 +12V
Page 21
P R E L I M I N A R Y
21
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
2.3 System Interfaces
2.3.1 PCI Express Interfaces
The COMe Ref. Carrier-i T6 TMI provides three general-purpose PCI Express (PCIe) lanes:
» PCIe#0 for the Mini PCIe half-size card slot, J24, connected to the SIM card socket, J35
» PCIe#1 for Mini PCIe full-size card slot, J21, muxed with SATA#1 (mSATA), connected to the
SIM card socket, J35. Mini PCIe may be enabled via the onboard DIP switch SW1.
» PCIe#2 for onboard Gigabit Ethernet Controller, U29
Note: The MiniPCIe full-size card slot, J21, is available as a standard feature on the COMe Ref.
Carrier-i T6 TMIV (Value) and the COMe Ref. Carrier-i T6 TMIP (Professional) versions.
2.3.2 SATA Interfaces
The COMe Ref. Carrier-i T6 TMI supports up to four SATA 6 Gb/s interfaces:
» SATA#0 via the 22-pin SATA plug connector, J5, through the redriver ICs, U2 and U3
» SATA#1 for the mSATA socket / Mini PCIe full-size card slot, J21, through the redriver ICs,
U10 and U11, muxed with PCIe#1 (Mini PCIe). mSATA may be enabled via the onboard DIP
switch, SW1.
» SATA#2 through the redriver ICs, U41 and U42, muxed with PEG#0 for the M.2 interface, J34
» SATA#3 via the 22-pin SATA receptacle connector, J33, through the redriver ICs, U6 and U8,
for the SATA 2.5” HDD mounting.
Note: The mSATA socket, J21, is available as a standard feature on the COMe Ref. Carrier-i T6
TMIV (Value) and the COMe Ref. Carrier-i T6 TMIP (Professional) versions.
Note: The SATA receptacle, J33, is available as a standard feature on the COMe Ref. Carrier-i T6
TMIP (Professional) version only.
2.3.3 M.2 Interface
The COMe Ref. Carrier-i T6 TMI provides an M.2 socket, J34, via PEG#[0-3] and SATA#2 (muxed with
PEG#0), which supports 3M key pinning and 2242, 2260 and 2280 M.2 modules.
Note: The M.2 socket, J34, is available as a standard feature on the COMe Ref. Carrier-i T6 TMIP
(Professional) version only.
2.3.4 Gigabit Ethernet Interfaces
The COMe Ref. Carrier-i T6 TMI provides up to two Gigabit Ethernet interfaces via two single RJ45 connectors:
» GBE#0 on RJ45 Ethernet connector, J18, directly via the COMe basic / compact Type 6 module
» GBE#1 on RJ45 Ethernet connector, J20, via the onboard Intel® Ethernet Controller I210-IT,
U29 (on PCIe#2)
Page 22
P R E L I M I N A R Y
22
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
The Ethernet connector LEDs have the following states:
LINK (green): Ethernet Link
ACT (green): 1000BASE-T Ethernet Speed
ACT (yellow): 100BASE-TX Ethernet Speed
ACT (off) + LINK (on): 10BASE-T Ethernet Speed
Note: The RJ45 Ethernet connector, J20, and the Intel® Ethernet Controller I210-IT, U29, are
available as a standard feature on the COMe Ref. Carrier-i T6 TMIV (Value) and the COMe
Ref. Carrier-i T6 TMIP (Professional) versions.
2.3.5 USB 2.0 Interfaces
The COMe Ref. Carrier-i T6 TMI supports eight high-speed USB 2.0 interfaces used as host:
» USB#[0;1] are used for USB 3.0/2.0 double-stack connector, J11.
5V standby power for wake events may be enabled and disabled via the onboard DIP switch,
SW1.
» USB#[2;3] are used for USB 3.0/2.0 pin header, J7
» USB#[4;5] are routed to the USB 2.0 double-stack connector, J10.
5V Standby Power for wake events may be enabled or disabled via the onboard DIP switch,
SW1.
» USB#6 is used for the Mini PCIe half-size interface to enable usage of USB 2.0 high-speed
Mini PCIe form factor devices.
» USB#7 is used for the Mini PCIe full-size / mSATA interface to enable usage of USB 2.0 high-
speed Mini PCIe form factor devices.
Page 23
P R E L I M I N A R Y
23
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
2.3.6 USB 3.0 Interfaces
The COMe Ref. Carrier-i T6 TMI supports four super-speed USB 3.0 interfaces used as host:
» USB_SS#[0;1] are routed to the USB 3.0/2.0 double-stack connector, J11.
» USB_SS#[2;3]) are routed to the 20-pin USB 3.0/2.0 pin header, J7.
The following figure and table provide pinout information for the USB 3.0/2.0 pin header, J7.
Note: The USB 3.0/2.0 pin header, J7, is available as a standard feature on the COMe Ref. Carrier-
i T6 TMIV (Value) and the COMe Ref. Carrier-i T6 TMIP (Professional) versions.
Figure 6: USB 3.0/2.0 Pin Header J7
110
20 11
J7
Table 8: Pinout of USB 3.0/2.0 Pin Header J7
PIN SIGNAL PIN SIGNAL
1Power 20--
2 SSRX2- 19 Power
3 SSRX2+ 18 SSRX3-
4 GND 17 SSRX3+
5SSTX2- 16GND
6 SSTX2+ 15 SSTX3-
7GND 14SSTX3+
8USB2- 13GND
9USB2+ 12USB3-
10 NC 11 USB3+
Page 24
P R E L I M I N A R Y
24
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
2.3.7 HD Audio Interfaces
The COMe Ref. Carrier-i T6 TMI provides HD Audio via the industrial grade HD Audio Codec IDT / Tempo
Semi 92HD73C (U13) through the following analog and digital audio connectors:
» Rear panel line-in connector, J25
» Rear panel SPK / line-out connector, J26
» Front panel HD audio header, J22
» S/PDIF header, J23
The following figure and table provide pinout information for the front panel HD audio header, J22.
The following figure and table provide pinout information for the S/PDIF header, J23.
Note: The HD Audio Codec including all of its functions is available as a standard feature on the
COMe Ref. Carrier-i T6 TMIV (Value) and the COMe Ref. Carrier-i T6 TMIP (Professional) versions.
Figure 7: Front Panel HD Audio Header J22
J22
9
1
10
2
Table 9: Front Panel HD Audio Header J22 Pinout
PIN SIGNAL PIN SIGNAL
10 LINE2_JD 9 LINE2_L
8- 7SENSE
6MIC2_JD 5LINE2_R
4PRESENCE# 3MIC2_R
2 GNDA 1 MIC2_L
Figure 8: S/PDIF Header J23
J23
1
4
Table 10: S/PDIF Header J23 Pinout
PIN SIGNAL
1SPDIF_OUT
2GND
3SPDIF_IN
4GND
Page 25
P R E L I M I N A R Y
25
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
2.3.8 UART Interfaces
The COMe Ref. Carrier-i T6 TMI provides two RS232 COM ports (RX/TX only) via the pin headers J30
(COM1/SER0) and J29 (COM2/SER1).
The following figure and table provide pinout information for the pin headers J30 (COM1/SER0) and
J29 (COM2/SER1).
2.3.9 GPIO Interfaces
The COMe Ref. Carrier-i T6 TMI provides four GPIs and four GPOs via a 10-pin GPIO pin header, J32.
The following figure and table provide pinout information for the GPIO pin header J32.
Figure 9: Pin Headers J30 and J29
J29
J30
1
2
3
1
2
3
Table 11: Pinout of Pin Headers J30 and J29
PIN SIGNAL ON J30 SIGNAL ON J29
3GND GND
2 SER0_RX SER1_RX
1SER0_TX SER1_TX
Figure 10: GPIO Pin Header J32
J32
J31
1
10
SH2
SH1
Table 12: GPIO Pin Header J32
PIN SIGNAL
10 GND
9GPO3
8GPO2
7GPO1
6GPO0
5GPI3
4GPI2
3GPI1
2GPI0
1 VCC 3.3V
Page 26
P R E L I M I N A R Y
26
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
2.3.10 SIM Interface
The COMe Ref. Carrier-i T6 TMI provides a SIM card socket, J35, connected to both Mini PCIe interfaces,
PCIe#0 and PCIe#1, to support radio-based services on Mini PCIe.
Note: The SIM card socket is available as a standard feature on the COMe Ref. Carrier-i T6 TMIV (Val-
ue) and the COMe Ref. Carrier-i T6 TMIP (Professional) versions.
2.3.11 SYS_Signals / Embedded Interfaces
On the COMe Ref. Carrier-i T6 TMI, a pin header for various SYS_Signals / embedded interfaces, J31, is
available and provides access to the following I/Os:
»I2C
»SMBus
» Watchdog
»LID
» SLEEP
The following figure and table provide pinout information for the pin header J31.
Figure 11: Pin Header J31
J32
J31
1
15
SH2
SH1
Table 13: Pin Header J31
PIN SIGNAL
15 GND
14 GND
13 GND
12 RAPID_SHDWN_IN
11 THRM#
10 LPC_SERIRQ
9 SLEEP#
8LID#
7WAKE1#
6WDT
5SMB_ALERT#
4SMB_DAT
3SMB_CK
2I2C_DAT
1I2C_CK
Page 27
P R E L I M I N A R Y
27
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
2.3.12 CPU Fan Interface
The COMe Ref. Carrier-i T6 TMI provides a 4-pin PWM fan connector, J4, directly controlled by the module fan output.
The following figure and table provide pinout information for the PWM fan connector J4.
2.3.13 Front Panel Interface
The COMe Ref. Carrier-i T6 TMI provides a front panel connector, J27, with access to the following signals:
» HDD activity LED
»Power LED
» Power button
» Reset button
» Speaker -out (Beep)
The following figure and table provide pinout information for the front panel connector J27.
Figure 12: PWM Fan Connector J4
J4
1
2
3
4
Table 14: PWM Fan Connector J4
PIN SIGNAL
1GND
212V
3SENSE
4 PWM Control
Figure 13: Front Panel Connector J27
J27
1
11
2
12
Table 15: Front Panel Connector J27 Pinout
PIN SIGNAL PIN SIGNAL
12 BEEP# 11 GND
10 GND 9 SYS_RESET#
8GND 7GND
6 BEEP+ 5 PWRBTN#
4GND 3ATA_ACT#
2 Power_LED+ 1 HDD_LED+
Page 28
P R E L I M I N A R Y
28
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
2.3.14 DIP Switch
The COMe Ref. Carrier-i T6 TMI provides one 8-position DIP switch, SW1, for board configuration.
Figure 14: DIP Switch SW1
The default setting is indicated by using italic bold.
Table 16: DIP Switch SW1 Functionality
POSITION SETTING FUNCTIONALITY
1 ON Disable rapid shutdown support for Kontron RXT modules
OFF Enable rapid shutdown support for Kontron RXT modules
2 ON Enable 5V standby power supply on COMe module for ATX function (S-States)
OFF Disable 5V standby power supply on COMe module for ATX function (S-States)
3 ON Enable 5V standby power to USB ports USB#[4;5] for wake events
OFF Disable 5V standby power to USB ports USB#[4;5] for wake events
4 ON Enable 5V standby power to USB ports USB#[0;1] for wake events
OFF Disable 5V standby power to USB ports USB#[0;1] for wake events
5 ON Enable mSATA on full-size Mini PCIe / mSATA interface
OFF Disable mSATA on full-size MiniPCIe / mSATA interface
6 ON Enable booting from COMe module SPI Flash
OFF Disable booting from COMe module SPI Flash-Carrier BIOS enabled
7 ON Wireless disable for Mini PCIe
OFF Wireless enable for Mini PCIe
8 ON Reserved
OFF
132
4
576
8
ON
Page 29
P R E L I M I N A R Y
29
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
2.3.15 Power Supply and Management
The COMe Ref. Carrier-i T6 TMI supports fixed input voltage (12V only) as a standard feature via the DC
jack, J6.
Note: The COMe Ref. Carrier-i T6 TMIP (Professional) version also supports a wide input voltage
range (8.5V - 30V) by default via a wired power connector, J1. The COMe Ref. Carrier-i T6
TMIP can be powered up either through the J1 or the J6 connector.
Warning: Powering up the COMe Ref. Carrier-i T6 TMIP through power both connectors (J1 and J6) at
the same time may result in damage to the power supply unit/power adapter.
The following 12V power supply unit is recommended for use with the COMe Ref. Carrier-i T6 TMI:
» DELTA ELECTRONICS. MDS-150AAS12B
The following figure and table provide pinout information for the wired power connector, J1.
Note: The rapid shutdown feature is only available on the COMe Ref. Carrier-i T6 TMIV (Value) and
the COMe Ref. Carrier-i T6 TMIE (Entry) versions if rapid shutdown is supported by the COMe
module used and enabled via the onboard DIP switch, SW1.
The following mating power connectors are recommended for use with the COMe Ref. Carrier-i T6 TMI:
» Wurth Electronics, Part Numbers: 691361100004 / 691363110004
» TE Connectivity AMP Connectors, Part Numbers: 284506-4 / 1986692-4 / 1986693-4
2.3.16 RTC
The COMe Ref. Carrier-i T6 TMI provides a 2-pin connector, J36, for an external CMOS battery. In addition, the following versions provide a goldcap, C35, for RTC backup:
» COMe Ref. Carrier-i T6 TMIP (Professional): 2.5F goldcap
» COMe Ref. Carrier-i T6 TMIV (Value): 1.5F goldcap
Figure 15: Power Connector J1
1
4
J1
Table 17: Power Connector J1 Pinout
PIN SIGNAL
1V_IN
2V_IN
3GND
4GND
Page 30
P R E L I M I N A R Y
30
www.kontron.com
User Guide
COMe Ref. Carrier-i T6 TMI
Global Headquarters
Kontron S&T AG
Lise-Meitner-Str. 3-5
86156 Augsburg
Germany
Tel.: + 49 (0) 821 / 4086 0
Fax: + 49 (0) 821 / 4086 111
info@kontron.com
Loading...