Page 1
DP75
SERVICE HANDBOOK
July 2000
Ver. 1.0
KONICA CORPORATION
TECHNOLOGY SUPPORT CENTER
TOKYO JAPAN
KCSDP7510
Page 2
KONICA CORPORATION
COPYRIGHT ©2000
N55ZF0710
Page 3
CONTENTS
CONTENTS
SAFETY AND IMPORTANT WARNING ITEMS
Refer to the 7075 service handbook on page ..............C-1
1. LIST OF DIFFERENCE
LIST OF MAJOR DIFFERENCES BETWEEN
Konica 7075 AND DP75 .......................................... 1-1
2. OUTLINE
OUTLINE OF SYSTEM ........................................... 2-1
DP75 PRODUCT SPECIFICATIONS...................... 2-2
[1] Type...................................................................2-2
[2] Functions ........................................................... 2-2
[3] Applicable Print Paper ....................................... 2-2
[4] Options .............................................................. 2-2
[5] Particulars of Machine ....................................... 2-3
[6] Maintenance and Life ........................................ 2-3
[7] Consumables.....................................................2-3
[8] Environmental Conditions.................................. 2-3
1 LIST OF DIFFERENCE
2 OUTLINE
Page 4
CONTENTS
1 LIST OF DIFFERENCE
2 OUTLINE
Blank page
Page 5
1
LIST OF DIFFERENCE
1 LIST OF DIFFERENCE
Page 6
1 LIST OF DIFFERENCE
Blank page
Page 7
LIST OF DIFFERENCE
LIST OF MAJOR DIFFERENCES BETWEEN
Konica 7075 AND DP75
Specifications
Mechanisms
Electrical Control
7075Classification DP75 Reason for change
1.E-RDH memory capacity
Standard : 64MB
Maximum : 512MB
2. Options
VIkit : VI-601(option)
3.Weight
Approx. 280kg
4.Machine dimensions(mm)
887(W) x 775(D) x 1203(H)
1.Operation panel unit
Exclusively for 7075
2.Read section
Provided
3.DF-313
Standard
1.Image control program
Exclusively for 7075
2.Operation program
Exclusively for 7075
3.Printer control program
Exclusively for 7075
Standard : 128MB
Maximum : 512MB
(Standard)
Approx.260Kg
887(W) x 775(D) x 990(H)
Exclusively for DP75
Not provided
Not provided
Exclusively for DP75
Exclusively for DP75
Exclusively for DP75
1 LIST OF DIFFERENCE
· Specification change
· Specification change
· Elimination of DF-313
and reading section
· Elimination of DF-313
· Redesigned specifically
for printing
· Specification change
1 - 1
Page 8
LIST OF DIFFERENCE
1 LIST OF DIFFERENCE
Blank page
1 - 2
Page 9
2
OUTLINE
2 OUTLINE
Page 10
2 OUTLINE
Blank page
Page 11
OUTLINE OF SYSTEM
Paper
exit tray
DP75 PRODUCT SPECIFICATIONS
Expansion memory unit
[MU-401/402]
OUTLINE OF SYSTEM
LCT [LT-401]
Post Inserter
[PI-108]
Trimmer
[TU-108]
Finisher
[FS-108]
Finisher
[FS-108BM]
Network board
[KN-302]
Postscript 3
[PS-361]
2 OUTLINE
LCT [LT-411]
Printer Controller
[IP-601]
2 - 1
Page 12
DP75 PRODUCT SPECIFICATIONS
DP75 PRODUCT SPECIFICATIONS
[1] Type
2 OUTLINE
[2] Functions
Installation T ype:
Console type (floor-mounted type)
Print method:
Indirect electrostatic method
Photosensitive material:
OPC
Sensitizing method:
Laser writing
Paper feed trays:
Three stacked trays (two for 500
sheets of 80 g/m2 paper; one for
1000 sheets of 80 g/m2 paper)
A by-pass tray for various paper
sizes (150 sheets of 80 g/m2 paper)
LCT (4000 sheets of 80 g/m
paper)*1
*1: Optional
Print size:
A3 to A5
11x17 to 8.5x11, F4
Wide paper (314x445mm)
Warm-up time:
Less than 6 minutes*2
(20°C,rated voltage)
*2: 6 minutes is the machine for the
230VAC specification.
Warm-up time dif fers depending
on the Power source (voltage).
First print time:
3.9 seconds or less (for A4, 400dpi,
straight paper ejection with the
copied image facing up, paper feed
from tray 1)
Resolution switch time:
15 seconds or less
Continuous print speed (400dpi, prints/min
utes):
Size ppm
A4 75
Print setting guantity:
1 to 9999
E-RDH memory capacity:
standard 128MB
maximum 512MB
Special functions:
Interleaves, chapter, combination (2
in 1, 4 in 1, 8 in 1), booklet, OHP
interleave, auto tray function, duplex
print function, reversed image,
repeated print, thin/thick paper,
Image shift, single step print, density
shift, printing function, print
reservation, image rotation, weekly
timer, auto power save, auto shutoff,
2
full image function, EKC.
[3] Applicable Print Paper
Plain paper:
High quality paper 60 g/m2 to 90 g/m
Special paper (bypass feed only):
Tabs
OHP film
Blueprint master paper
Recycled paper
(tray feed only):
High quality paper (50 g/m2 to 59 g/m2,
91g/m2 to 200 g/m2)
2
[4] Options
Finisher: FS-108, FS-108BM
4000-sheets LCT: LT-401/LT-411
Expantion memory unit:
MU-401: 64MB
MU-402: 128MB
Post inserter: PI-108
Trimmer: TU-108
Printer controller: IP-601
Network board: KN-302
Post script 3: PS-361
Paper exit tray
2 - 2
Page 13
[5] Particulars of Machine
Power supply:
230 VAC -14% to 10.6%
50 Hz/60 Hz
Power consumption:
3450W max.
(Full option)
Weight: Approx. 260 kg
Machine dimensions (mm):
887(W) x 775(D) x 990(H)
[6] Maintenance and Life
Periodic maintenance:
Every 250,000 prints
Machine life:
30,000,000 prints or 5 years
[7] Consumables
Developer:Common with Konica 7075
Toner : Common with Konica 7075
Drum: Common with Konica 7075 (ø100)
DP75 PRODUCT SPECIFICATIONS
2 OUTLINE
[8] Environmental Conditions
Temperature:
10°C to 30°C (50°F to 86°F)
Humidity: 10% to 80% RH
Note: The information herein may subject to change
for improvement without notice.
2 - 3
Page 14
MAIN UNIT
2 OUTLINE
Blank page
2 - 4
Loading...